aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/files
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add support for ZTE MF286DPawel Dembicki2022-02-051-0/+435
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZTE MF286D is a LTE router with four gigabit ethernet ports and integrated QMI mPCIE modem. Hardware specification: - CPU: IPQ4019 - RAM: 256MB - Flash: NAND 128MB + NOR 2MB - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2 - LTE: mPCIe cat 12 card (Modem chipset MDM9250) - LAN: 4 Gigabit Ports - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem) - Serial console: X8 connector 115200 8n1 Known issues: - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs are driven by cpu. - Wifi LED is triggered by phy0tpt only - No VoIP support - LAN1/WAN port is configured as WAN - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN and WLAN0/1 Opening the case: 1. Take of battery lid (no battery support for this model, battery cage is dummy). 2. Unscrew screw placed behind battery lid. 3. Take off back cover. It attached with multiple plastic clamps. 4. Unscrew four more screws hidden behind back case. 5. Remove front panel from blue chassis. There are more plastic clamps. 6. Unscrew two boards, which secures the PCB in the chassis. 7. Extract board from blue chassis. Console connection (X8 connector): 1. Parameters: 115200 8N1 2. Pin description: (from closest pin to X8 descriptor to farthest) - VCC (3.3V) - TX - RX - GND Install Instructions: Serial + initramfs: 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.1.3 2. Connect serial console (115200,8n1) to X8 connector. 3. Connect TFTP server to RJ-45 port. 4. Stop in u-Boot and run u-Boot commands: setenv serverip 192.168.1.3 setenv ipaddr 192.168.1.72 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock. 6. Login via ssh or serial and remove stock partitions: ubiattach -m 9 ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. Install image via "sysupgrade -n". Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cosmetic changes to the commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add MikroTik cAP ac supportAlar Aun2022-02-011-0/+250
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBcAPGi-5acD2nD (cAP ac), a indoor dual band, dual-radio 802.11ac wireless AP, two 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/cap_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 port, PoE in and passive PoE out Unsupported: - PoE out Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Alar Aun <alar.aun@gmail.com>
* ipq40xx: rename RT-AC42U WLAN/LAN LEDsSungbo Eo2022-01-171-4/+6
| | | | | | | | | | Assign LED numbers properly by adding function-enumerator property in DTS. While at it, remove default trigger of LAN LEDs as it will be handled in 01_leds anyway. Fixes: 51b9aef553a8 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: AP-365: fix non-existent node or label "macaddr_mfginfo_1d"Christian Lamparter2022-01-161-0/+7
| | | | | | | | | | | | | | | | | | | Chen Minqiang reported on github: | DTC arch/arm/boot/dts/qcom-ipq4029-ap-365.dtb |qcom-ipq4019.dtsi:520.23-560.5: ERROR (phandle_references): /soc/wifi@a000000: |Reference to non-existent node or label "macaddr_mfginfo_1d" | | also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:243.8-248.3 |qcom-ipq4019.dtsi:562.23-602.5: ERROR (phandle_references): /soc/wifi@a800000: |Reference to non-existent node or label "macaddr_mfginfo_1d" | | also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:250.8-256.3 |ERROR: Input tree has errors, aborting (use -f to force output) |scripts/Makefile.lib:326: recipe for target 'qcom-ipq4029-ap-365.dtb' failed Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: utilize nvmem-cells for macs & (pre-)calibration dataChristian Lamparter2022-01-1530-36/+482
| | | | | | | | | | | | | | | moves extraction entries out of 11-ath10k-caldata and into the individual board's device-tree. Some notes: - mmc could work as well (not tested) - devices that pass the partitions via mtdparts bootargs are kept as is - gl-b2200 has a weird pcie wifi device (vendor claims 9886 wave 2. But firmware-extraction was for a wave 1 device?!) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-ACRH17/RT-AC42UJoshua Roys2022-01-152-10/+308
| | | | | | | | | | | | | | | | | | | | | SOC: IPQ4019 CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d DRAM: 256 MB NAND: 128 MiB Macronix MX30LF1G18AC ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN) USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4 INPUT: 1x WPS, 1x Reset LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed with an intermediary initramfs image, the jffs2 ubi volume deleted, and then finally a sysupgrade with the final image performed. Signed-off-by: Joshua Roys <roysjosh@gmail.com> (added ALT0) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix reset button GPIO for GL.iNet GL-B2200Enrico Mioso2021-12-121-1/+1
| | | | | | | | | GL.iNet's U-Boot checks for GPIO 40, not 43. Changing this allows the RESET button to work as expected. Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> CC: Daniel Golle <daniel@makrotopia.org> CC: Li Zhang <li.zhang@gl-inet.com>
* ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUPChristian Lamparter2021-12-041-0/+34
| | | | | | | | | | introduce nvmem pre-cal + mac-address cells for both Wifis and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of the few devices in which the correct mac adress is already at the right place for Wifi, so no separate nvmem cell is needed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for GL.iNet GL-B2200TruongSinh Tran-Nguyen2021-12-021-0/+364
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dishAlexander Couzens2021-12-021-0/+269
| | | | | | | | | | | | | | | | | | | | | | | | | | | | LHGG-60ad is IPQ4019 + wil6210 based. Specification: - Qualcomm IPQ4019 (717 MHz) - 256 MB of RAM (DDR3L) - 16 MB (SPI NOR) of flash - 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035. - WLAN: wil6210 802.11ad PCI card - No USB or SD card ports - UART disabled - 8x LEDs Biggest news is the wil6210 PCI card. Integration for its configuration and detection has already been taken care of when adding support for TP-Link Talon AD7200. However, signal quality is much lower than with stock firmware, so probably additional board-specific data has to be provided to the driver and is still missing at the moment. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [Fix Ethernet Interface] Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: Add support for Teltonika RUTX10Felix Matouschek2021-11-282-0/+277
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org>
* ipq40xx: add support for MikroTik hAP ac3Robert Marko2021-11-281-0/+328
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD (hAP ac³), a indoor dual band, dual-radio 802.11ac wireless AP with external omnidirectional antennae, USB port, five 10/100/1000 Mbps Ethernet ports and PoE passthrough. See https://mikrotik.com/product/hap_ac3 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR + 128 MB NAND - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in, PoE passtrough on port 5 - 1x USB Type A port Installation: 1. Boot the initramfs image via TFTP 2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1" 3. Use ubiformat to remove MikroTik specific UBI volumes * Detach the UBI partition by running: "ubidetach -d 0" * Format the partition by running: "ubiformat /dev/mtdN -y" Replace mtdN with the correct mtd index from step 2. 3. Flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com> Tested-by: Mark Birss <markbirss@gmail.com> Tested-by: Michael Büchler <michael.buechler@posteo.net> Tested-by: Alex Tomkins <tomkins@darkzone.net>
* ipq40xx: utilize nvmem on Netgear EX61X0 v2 SeriesChristian Lamparter2021-11-281-0/+27
| | | | | | | | the Netgear EX6100v2 and EX6150v2 can utilize the nvmem for the pre-calibration and mac-address for both WIFI devices. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: purge clk_ignore_unused bootargChristian Lamparter2021-11-272-2/+2
| | | | | | | | | these flags have been creeping in from the QSDK. All needed clocks should be accounted for, and if a device is broken due to this. It should be looked into. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix missing includeChristian Lamparter2021-11-141-0/+1
| | | | | | | | | | | | This patch fixes a blunder of mine. The include needed for LED_COLOR_ID_BLUE property is missing. This caused the builds to fail with: |Error: arch/arm/boot/dts/qcom-ipq4019-r619ac.dtsi:91.13-14 syntax error |FATAL ERROR: Unable to parse input tree Fixes: 12d33d388c52 ("ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)Richard Yu2021-11-143-0/+378
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work <https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c> With some changes: 1. Added `qpic_bam` node in dts. I don't know much about this, but I observed other dtses have this node. 2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not working. This fix is from <https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2> 3. Removed the 32MB NOR variant. 4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes wlan2g led light up. 5. Added ethphy led config in dts. 6. Changed nand partition label from `rootfs` to `ubi`. About the 128MiB variant: The stock bootloader sets size of nand to 64MiB. But most of this devices have 128MiB nand. If you want to use all 128MiB, you need to modify the `MIBIB` data of bootloader. More details can be found on github: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060> For instructions on how to flash the MIBIB partition from u-boot console: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232> About the Mini PCIe slot: (from "ygleg") "The REFCLK signals on the Mini PCIe slot is not connected on this board out of the box. If you want to use the Mini PCIe slot on the board, you need to (preferably) solder two 0402 resistors: R436 (REFCLK+) and R444 (REFCLK-)..." This and much more information is provoided in the github comment: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670> Signed-off-by: Richard Yu <yurichard3839@gmail.com> Signed-off-by: DENG Qingfang <dqfext@gmail.com> [Added comment about MIBIB+128 MiB variant. Added commit message section about pcie slot. Renamed gpio-leds' subnodes and added color, function+enum properties.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50Davide Fioravanti2021-11-015-0/+409
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost identical AC3000 routers. The SRR60 has one port labeled as wan while the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a different external shape but they have an USB 2.0 port on the back. This patch has been tested only on SRS60 and RBR50, but should work on SRR60 and RBS50. Hardware -------- SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads) RAM: 512MB DDR3 FLASH: 4GB EMMC ETH: - 3x 10/100/1000 Mbps Ethernet - 1x 10/100/1000 Mbps Ethernet (WAN) WIFI: - 2.4GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x QCA9984 (4x4:4) - 6 internal antennas BTN: - 1x Reset button - 1x Sync button - 1x ON/OFF button LEDS: - 8 leds controlled by TLC59208F (they can be switched on/off independendently but the color can by changed by GPIOs) - 1x Red led (Power) - 1x Green led (Power) UART: - 115200-8-N-1 Everything works correctly. Installation ------------ These routers have a dual partition system. However this firmware works only on boot partition 1 and the OEM web interface will always flash on the partition currently not booted. The following steps will use the SRS60 firmware, but you have to chose the right firmware for your router. There are 2 ways to install Openwrt the first time: 1) Using NMRPflash 1. Download nmrpflash (https://github.com/jclehner/nmrpflash) 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img file in the same folder of the nmrpflash executable 3. Connect your pc to the router using the port near the power button. 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img". Replace XXX with your network interface (can be identified by running "nmrpflash -L") 5. Power on the router and wait for the flash to complete. After about a minute the router should boot directly to Openwrt. If nothing happens try to reboot the router. If you have problems flashing try to set "10.164.183.253" as your computer IP address 2) Without NMRPflash The OEM web interface will always flash on the partition currently not booted, so to flash OpenWrt for the first time you have to switch to boot partition 2 and then flash the factory image directly from the OEM web interface. To switch on partition 2 you have to enable telnet first: 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet". 2. Connect through telent ("telnet 192.168.1.250") and login using admin/password. To read the current boot_part: artmtd -r boot_part To write the new boot_part: artmtd -w boot_part 02 Then reboot the router and then check again the current booted partition Now that you are on boot partition 2 you can flash the factory Openwrt image directly from the OEM web interface. Restore OEM Firmware -------------------- 1. Download the stock firmware from official netgear support. 2. Follow the nmrpflash procedure like above, using the official Netgear firmware (for example SRS60-V2.2.1.210.img) nmrpflash -i XXX -f SRS60-V2.2.1.210.img Notes ----- 1) You can check and edit the boot partition in the Uboot shell using the UART connection. "boot_partition_show" shows the current boot partition "boot_partition_set 1" sets the current boot partition to 1 2) Router mac addresses: LAN XX:XX:XX:XX:XX:69 WAN XX:XX:XX:XX:XX:6a WIFI 2G XX:XX:XX:XX:XX:69 WIFI 5G XX:XX:XX:XX:XX:6b WIFI 5G (2nd) XX:XX:XX:XX:XX:6c LABEL XX:XX:XX:XX:XX:69 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com> [added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved sysupgrade mmc.sh to here and renamed it, various dtsi changes] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: MR33: Fix LP5562 LED driver probeTan Zien2021-10-231-4/+15
| | | | | | | | | | | | | Add the reg and color property to each channel node. This update is to accommodate the multicolor framework. Refer to: <https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com> <https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com> Signed-off-by: Tan Zien <nabsdh9@gmail.com> [replaced links to lore, wrote something of a commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: 5.10: move AR40xx to MDIO driversRobert Marko2021-09-252-2232/+0
| | | | | | | | | | | MDIO drivers were moved into their own sub directory of networking drivers. This has caused the AR40xx driver to probe before MDIO drivers and that wont work as it depends on the MDIO bus to be up so it can be fetched. Lets solve it by moving the AR40xx into MDIO folder so they get probed like before. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: reject unsupported coalescing paramsRobert Marko2021-09-251-0/+4
| | | | | | | | | | | Set ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters. This driver did not previously reject unsupported parameters. This is a required ethtool op since kernel 5.7. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: update of_get_phy_mode() for 5.10Robert Marko2021-09-251-1/+9
| | | | | | | | | | In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0 or errors instead of phymode. Phymode is now returning by passing a pointer to phy_interface_t where it will be stored. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: ar40xx: reset port status registerDavid Bauer2021-08-141-2/+1
| | | | | | | This resolves incosnsitencies of the configured RX / TX flow control modes between different boards or bootloaders. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: ar40xx: use FIELD_GET macroDavid Bauer2021-08-141-7/+8
| | | | | | This improves code readability. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: increase EX6150v2 SPI frequencyDavid Bauer2021-08-141-1/+1
| | | | | | | | | The chip supports clock speeds up to 50 MHz, however it won't even read the chip-id correctly at this frequency. 45 MHz however works reliable. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: backport support for nvmem on non platform devicesAnsuel Smith2021-08-051-5/+1
| | | | | | | | | | | | In the current state, nvmem cells are only detected on platform device. To quickly fix the problem, we register the affected problematic driver with the of_platform but that is more an hack than a real solution. Backport from net-next the required patch so that nvmem can work also with non-platform devices and rework our current patch. Drop the mediatek and dsa workaround and rework the ath10k patches. Rework every driver that use the of_get_mac_address api. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq40xx: convert mtd-mac-address to nvmem implementationAnsuel Smith2021-07-192-4/+32
| | | | | | | Define nvmem-cells and convert mtd-mac-address to nvmem implementation. The conversion is done with an automated script. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq40xx: fix FRITZRepeater 1200 RGMII delayDavid Bauer2021-07-171-1/+1
| | | | | | | | | | | | | | When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the at803x PHY driver incorrectly set up the delays, not disabling delays set by the bootloader. The PHY was always operating with RX as well as TX delays enabled, but with kernel 5.4 and later, the required TX delay is disabled, breaking ethernet operation. Correct the PHY mode, so the driver enables both delays. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: increase SPI frequency for Zyxel NBG6617Dmitry Tunin2021-07-111-3/+3
| | | | | | | | | | | | The mx25l25635f supports clock speed up to 50Mhz. Also remove obsolete "mx25l25635f" hack and rename the matching device-tree flash node. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [mention node rename as well. chip is very very likely always the "f" revision for all NBG6617] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-051-0/+371
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix hard_config partition size on MikroTik hAP-ac2Baptiste Jonglez2021-05-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The routerbootparts driver dynamically discovers the location of MikroTik partitions, but it cannot determine their size (except by extending them up to the start of the next discovered partition). The hard_config partition has a default size of 0x1000 in the driver, while it actually takes 0x2000 on the hAP-ac2. Set the correct size in the hAP-ac2 DTS. On most devices, this isn't a problem as the actual data fits in 0x1000 bytes. However, some devices have larger data that doesn't fit in 0x1000 bytes. In any case, all devices seen so far have enough space for a 0x2000 hard_config partition before the start of the dtb_config partition. With the current 0x1000 size: 0x00000000e000-0x00000000f000 : "hard_config" 0x000000010000-0x000000017bbc : "dtb_config" With this patch extending the size to 0x2000: 0x00000000e000-0x000000010000 : "hard_config" 0x000000010000-0x000000017bbc : "dtb_config" Other ipq40xx boards may need the same fix but it needs testing. References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324 Acked-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* ipq40xx: add support for MikroTik SXTsq 5 acRoger Pueyo Centelles2021-04-291-0/+242
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD), an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet port. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in - 1x Ethernet LED (green) - 7x user-controllable LEDs · 1x power (blue) · 1x user (green) · 5x rssi (green) Note: Serial UART is probably available on the board, but it has not been tested. Flashing: Boot via TFTP the initramfs image. Then, upload a sysupgrade image via SSH and flash it normally. More info at the "Common procedures for MikroTik products" page https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ipq40xx: add MikroTik hAP ac2 supportRobert Marko2021-04-051-0/+272
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: net: phy: qca807x: fix GPIO driverRobert Marko2021-03-051-0/+1
| | | | | | | | | | | While rebasing into setting bits instead of magic values, I accidentally forgot to actually set the force bit. Without it using the pins as GPIO-s did not actually work. Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* uboot-envtools: add support for Aruba AP-303 and AP-365Jan Alexander2021-01-142-3/+0
| | | | | | | | | Both devices use u-boot env variables to boot OpenWrt from its flash partition. Using u-boot envtools, it is possible to change the bootcmd back to the stock firmware partition directly from OpenWrt without attaching a serial cable or even physically accessing the device. Signed-off-by: Jan Alexander <jan@nalx.net>
* ipq40xx: remove unnecessary execute permission bitSungbo Eo2021-01-031-0/+0
| | | | | | | | | DTS files do not need to be executable. 644 is enough. Fixes: 0fbdb51f7643 ("ipq40xx: add Edgecore OAP-100 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> [split by targets] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: remove non-existent ethernet PHYDavid Bauer2020-12-302-0/+8
| | | | | | | | | Since updating the MDIO driver, the probe will fail hard on any PHY not present on the bus, while this was not the case prior. Fixes commit 26b1f72381fb ("ipq40xx: net: phy: ar40xx: remove PHY handling") Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for GL.iNet GL-AP1300Dongming Han2020-12-251-0/+269
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq40xx: net: ethernet: edma: use generic PHY printRobert Marko2020-12-231-2/+2
| | | | | | | | | | | | | Lets use the generic upstream phy_print_status() instead of doing something similar by hand. Before: ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000 After: ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: use generic ksettings functionsRobert Marko2020-12-231-56/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since we now have a proper PHY driver for QCA807x and AR803x has already been supported properly there is no need for the driver to be poking on PHY registers for ethtool ops. So, lets simply use the generic phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions. This also has the advantage of properly populating stuff other than speeds like, transceiver type, MDI-X etc. ethtool before: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes ethtool after: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: Symmetric Receive-only Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: external Auto-negotiation: on MDI-X: off (auto) Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: dts: convert PHY GPIO bindingsRobert Marko2020-12-232-22/+41
| | | | | | | | | | Since the new PHY driver manages each PHY individually and therefore registers each PHY that is marked with gpio-controller; DT property as a GPIO controller we need to convert old DT bindings to account for this. Only 2 boards use this so its not much of an issue. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: fix link detectionRobert Marko2020-12-231-0/+4
| | | | | | | PHY needs to be soft reset before starting it from ethernet driver as AR40xx calibration will leave it in unwanted state. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: phy: ar40xx: remove PHY handlingRobert Marko2020-12-231-225/+16
| | | | | | | | | | | | | | | Since we now have proper PHY driver for the QCA807x PHY-s, lets remove PHY handling from AR40xx. This removes PHY driver, PHY GPIO driver and PHY init code. AR40xx still needs to handle PSGMII calibration as that requires R/W from the switch, so I am unable to move it into PHY driver. This also converted the AR40xx driver to use OF_MDIO to find the MDIO bus as it now cant be set through the PHY driver. So lets depend on OF_MDIO in KConfig. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add Qualcomm QCA807x driverRobert Marko2020-12-231-0/+828
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s. They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s. They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC, while second one is SGMII for connection to MAC or fiber. Both models have a combo port that supports 1000BASE-X and 100BASE-FX fiber. Each PHY inside of QCA807x series has 2 digitally controlled output only pins that natively drive LED-s. But some vendors used these to driver generic LED-s controlled by user space, so lets enable registering each PHY as GPIO controller and add driver for it. This also adds the ability to specify DT properties so that 1000 Base-T LED will also be lit up for 100 and 10 Base connections. This is usually done by U-boot, but boards running mainline U-boot are not configuring this yet. These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x boards. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: edma: convert to of_mdio_find_bus()Robert Marko2020-12-231-21/+4
| | | | | | | | | | | | | | With the reworked MDIO driver, EDMA will fail to get the MII BUS as it used the MII BUS stored inside the MDIO structure private data. This obviously does not work with the modernized driver, so lets switch to using a purpose build of_mdio_find_bus() which will return the MII BUS and only requires the MDIO node to be passed. This is easy as we already have the node parsed. Also, since we now require OF_MDIO add that as dependency. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add support for devolo Magic 2 WiFi nextStefan Schake2020-12-221-0/+268
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
* ipq40xx: add support for Plasma Cloud PA2200Marek Lindner2020-12-221-0/+210
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for Plasma Cloud PA1200Marek Lindner2020-12-221-0/+197
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: revert usage of VLAN S-TAGDavid Bauer2020-12-142-37/+9
| | | | | | | | | | | This reverts the usage of the S-Tag for separating LAN and WAN port on the embedded switch. Many users complained about not being able to manage C-Tag addition / removal on the switch as well as degraded performance. Fixes: commit 9da2b567605b ("ipq40xx: fix ethernet vlan double tagging") Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix 5Ghz tx/rx power on the ASUS MAP-AC2200Yushi Nishida2020-12-131-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | The ASUS MAP-AC2200 suffers from a lower transmit/receive signal power as compared to the stock firmware. Upon investigation, it was discovered that stock firmware from the GPL_MAP-AC2200_3.0.0.4.384.46249-g97d05bb.tar archive. set the following GPIOs in "release/src/router/rc/init.c". GPIO 44 and 46 have to be set to output high GPIO 45 and 47 have to be set to output low Here are some results, after activating the relevant gpios through cmdline: <https://forum.openwrt.org/t/asus-map-ac2200-low-transmit-receive-signal-5ghz/69005/12> THX @ slh Fixes: 9ad3967f140 ("ipq40xx: add support for ASUS Lyra") Signed-off-by: Yushi Nishida <kyro2man@gmx.net> [slightly rewritten commit, added missing <>) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: DTS style updates for OpenMesh devicesSven Eckelmann2020-11-232-46/+18
| | | | | | | | | | | | | | | | | The OpenMesh related files were not updated since a while and the new coding style requirements weren't integrated. This can cause problems for new devices when an author uses these files as starting point. * use SPDX-License-Identifiers instead of full license texts * drop linux,default-trigger with value default-off for LEDs * led nodes with label "abc:xyz" should have name "xyz_abc" * led DT labels for "xyz_abc" should be "led_xyz_abc" * "m25p80@0" flash node should be renamed to "flash@0" * drop unnecessary empty lines Signed-off-by: Sven Eckelmann <sven@narfation.org> [minor commit title and message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 15:21:45 +0000