aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add support for Crisis Innovation Lab MeshPoint.OneRobert Marko2019-11-304-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon Jalapeno module from 8Devices). MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and smart city gateway that can be installed and powered from street lighting (even solar power in the future). MeshPoint provides up to 27 hours of interrupted Wi-Fi and IoT services from internal battery even when external power is not available. MeshPoint.One can be used for disaster relief efforts in order to provide instant Wi-Fi coverage that can be easily expanded by just adding more devices that create wide area mesh network. MeshPoint.One devices have standard Luci UI for management. Features: - 1x 1Gpbs WAN - 1x 1Gbps LAN - POE input (eth0) - POE output (eth1) - Sensor for temperature, humidity and pressure (Bosch BME280) - current, voltage and power measurement via TI INA230 - Hardware real time clock - optional power via Li-Ion battery - micro USB port with USB to serial chip for easy OpenWrt terminal access - I2C header for connecting additional sensors Installation: ------------- Simply flash the sysupgrade image from stock firmware. Or use the built in Web recovery into bootloader: Hold Reset button for 5 to 20 seconds or use UART and httpd command. Web UI will appear on 192.168.2.100 by default. For web recovery use the factory.ubi image. Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr> Signed-off-by: Damir Franusic <damir.franusic@sartura.hr> Signed-off-by: Valent Turkovic <valent@meshpoint.me> Signed-off-by: Robert Marko <robert@meshpoint.me> [commit description long line wrap, usb->USB] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: ipq4019: Add new device Compex WPJ419Daniel Danzberger2019-11-023-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device contains 2 flash devices. One NOR (32M) and one NAND (128M). U-boot and caldata are on the NOR, the firmware on the NAND. SoC: IPQ4019 CPU: 4x 710MHz ARMv7 RAM: 256MB FLASH: NOR:32MB NAND:128MB ETH: 2x GMAC Gigabit POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V) WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO 1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO USB: 1x 3.0 PCI: 1x Mini PCIe SIM: 1x Slot SD: 1x MicroSD slot BTN: Reset LED: - Power - Ethernet UART: 1x Serial Port 4 Pin Connector (UART) 1x Serial Port 6 Pin Connector (High Speed UART) POWER: 12V 2A Installation ------------ Initial flashing can only be done via u-boot using the following commands: tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi nand erase.chip; nand write ${fileaddr} 0x0 ${filesize} res Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
* ipq40xx: add support for AVM FRITZ!Repeater 1200David Bauer2019-10-233-4/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add missing backslash in 11-ath10k-caldataDavid Bauer2019-10-231-1/+1
| | | | | | | This adds a missing backslash in the caldata-extraction script. Without this fix, caldata extraction fails for every device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: Add support for Unielec U4019Kristian Evensen2019-10-212-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* treewide: use a single ath10k MAC patching function with checksumAdrian Schmutzler2019-10-151-12/+12
| | | | | | | | | | | | | | | | While all ath10k eeproms have a checksum field, so far two functions for patching ath10k MAC address have been present (and been used). This merges code to provide a single function ath10k_patch_mac in caldata.sh, having its name in accordance with ath9k functions. By doing so, correct MAC patching for current and future ath10k devices should be ensured. This patch adds checksum adjustments for several targets on ath79 and lantiq. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move MAC address patch functions to common libraryAdrian Schmutzler2019-10-141-25/+0
| | | | | | | | | This unifies MAC address patch functions and moves them to a common script. While those were implemented differently for different targets, they all seem to do the same. The number of different variants is significantly reduced by this patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move calibration data extraction function to libraryAdrian Schmutzler2019-10-131-74/+27
| | | | | | | | | | | | | | | | | This moves the almost identical calibration data extraction functions present multiple times in several targets to a single library file /lib/functions/caldata.sh. Functions are renamed with more generic names to merge different variants that only differ in their names. Most of the targets used find_mtd_chardev, while some used find_mtd_part inside the extraction code. To merge them, the more abundant version with find_mtd_chardev is used in the common code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [rebase on latest master; add mpc85xx] Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: move xor() from caldata extraction to functions.shAdrian Schmutzler2019-10-131-16/+1
| | | | | | | | The xor() function is defined in each of the caldata extraction scripts for several targets. Move it to functions.sh to reduce duplicate code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: sysupgrade: use $UPGRADE_BACKUP to check for backupRafał Miłecki2019-09-112-2/+2
| | | | | | | Now that $UPGRADE_BACKUP is set conditionally there is no need to check the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-052-2/+2
| | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: replace remaining (not working now) $SAVE_CONFIG usesRafał Miłecki2019-09-052-2/+2
| | | | | | | This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG Fixes: b534ba961100 ("base-files: pass "save_config" option to the "sysupgrade" method") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: sync bootcount scripts across targetsChuanhong Guo2019-08-171-3/+1
| | | | | | | | | | | | | | | This commit made the following changes to sync all bootcount scripts: 1. use boot() instead of start() This script only needs to be executed once when boot is complete. use boot() to make this explicit. 2. drop sourcing of /lib/functions.sh This is aready done in /etc/rc.common. 3. ramips: replace board name checking with a case Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ipq40xx: fix AVM NAND caldata extractionDavid Bauer2019-08-151-3/+15
| | | | | | | | | | | | | The AVM Fritz!Box 7530 (and probably other AVM IPQ4019 NAND devices) has it's caldata not stored consistently, but instead at currently 3 known possible offsets. As we get a non-zero exit code from fritz_cal_extract, simply try all three possible offsets on both bootloader partitions, until a matching caldata for each radio is found. Reported-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: convert WiFi caldata size and offset to hexadecimalAdrian Schmutzler2019-08-141-29/+29
| | | | | | | | | | | | | | This changes size and offset set for WiFi caldata extraction and MAC address adjustment to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-cal-data in DTS files. Since dd cannot deal with hexadecimal notation, one has to convert back to decimal by simple $(($hexnum)). Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-143-9/+9
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: sysupgrade: get rid of platform_nand_pre_upgrade()Rafał Miłecki2019-07-221-23/+11
| | | | | | | | | | | 1) nand_do_upgrade() is always called by a target code 2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade() It means there is no need for the platform_nand_pre_upgrade() callback at all. All code that was present there could bo moved & simplly called by a target right before the nand_do_upgrade(). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-4/+4
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq40xx: Linksys: sysupgrade: Ensure OEM volumes are removedJeff Kletsky2019-06-201-20/+22
| | | | | | | | | | | | | | | | | | When OEM volumes are present in the [alt_]firmware partition, sysupgrade will write a new kernel, but will fail to write the root file system. The next boot will hang indefinitely Waiting for root device /dev/ubiblock0_0... Modified ipq40xx/base-files/lib/upgrade/linksys.sh to remove both `squashfs` and `ubifs` if found on the target firmware partition's UBI device. Run-tested-on: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [applied some shellcheck suggestions as well]
* ipq40xx: Add support for Linksys EA8300 (Dallas)Jeff Kletsky2019-05-186-9/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* mtd: base-files: Unify dual-firmware devices (Linksys)Jeff Kletsky2019-05-183-52/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
* ipq40xx: add support for EnGenius ENS620EXTSteve Glennon2019-03-213-1/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M FLASH: 32M SPI NOR W25Q256 ETH: QCA8075 WiFi2: IPQ4018 2T2R 2SS b/g/n WiFi5: IPQ4018 2T2R 2SS n/ac LED: - Power amber - LAN1(PoE) green - LAN2 green - Wi-Fi 2.4GHz green - Wi-Fi 5GHz green BTN: - WPS UART: 115200n8 3.3V J1 VCC(1) - GND(2) - TX(3) - RX(4) Added basic support to get the device up and running for a sysupgrade image only. There is currently no way back to factory firmware, so this is a one-way street to OpenWRT. Install from factory condition is convoluted, and may brick your device: 1) Enable SSH and disable the CLI on the factory device from the web user interface (Management->Advanced) 2) Reboot the device 3) Override the default, limited SSH shell: a) Get into the ssh shell: ssh admin@192.168.1.1 /bin/sh --login b) Change the dropbear script to disable the limited shell. At the empty command prompt type: sed -i '/login_ssh/s/^/#/g’ dropbear /etc/init.d/dropbear restart exit 4) ssh in to a (now-) normal OpenWRT SSH session 5) Flash your built image a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin admin@192.168.1.1:/tmp/ b) ssh admin@192.168.1.1 c) sysupgrade -n /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin 6) After flash completes (it may say "Upgrade failed" followed by "Upgrade completed") and device reboots, log in to newly flashed system. Note you will now need to ssh as root rather than admin. Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> [whitespace fixes, reordered partitions, removed rng node from 4.14, fixed 901-arm-boot-add-dts-files.patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for AVM FRITZ!Repeater 3000David Bauer2019-03-133-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M (NANYA NT5CC128M16JR-EK) FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI) ETH: Qualcomm QCA8072 WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac WiFi5: QCA9984 4T4R 4SS n/ac LED: - Connect green/blue/red - Power green BTN: WPS/Connect UART: 115200n8 3.3V VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz3000' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ3000.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz3000.bin uboot0 > mtd write /path/to/uboot-fritz3000.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: tidy up 02_networksChristian Lamparter2019-03-131-2/+2
| | | | | | | | - fix linksys' EA6350v3 order - remove whitespace that should have been tabs Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for FritzBox 7530David Bauer2019-02-284-3/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Qxwlan E2600AC C1 and C2张鹏2019-02-284-13/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ALFA Network AP120C-ACPiotr Dymacz2019-02-265-2/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 4x LED (all driven by GPIO) - 1x button (reset) - 1x USB 2.0 (optional, not installed in indoor version) - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) Flash instruction: 1. This board uses dual-image feature (128 MB NAND is divided into two 64 MB partitions: 'rootfs1' and 'rootfs2'). 2. Before update, make sure your device is running firmware no older than v1.1 (previous versions have incompatible U-Boot). 3. Use 'factory' image in vendor GUI or for sysupgrade tool, without preserving settings. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: speed up ath10k-caldata extractionChristian Lamparter2019-02-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reading and writing to and from flash storage is slow and currently, the ath10kcal_extract() scripts are even more at an disadvantage because they use a block size of 1 to be able skip. This patch reworks the extraction scripts to be much faster and efficient by reading and writing the calibration data in possibly one big block. before: (Tested on a RT-AC58U, which has SPI-NAND). # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064 12064+0 records in 12064+0 records out real 0m 0.28s user 0m 0.02s sys 0m 0.24s after: # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.01s user 0m 0.00s sys 0m 0.00s Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3Oever González2019-02-141-1/+1
| | | | | | | | | | | | | This commit fixes the script that sets the MAC address of the LAN switch. The LAN MAC address should be the WAN MAC address plus one. Without this patch the WAN and the LAN interface will use the same MAC address and an error will be generated. With this patch all interfaces will have a different MAC address, consecutive in the following order: WAN, LAN, radio0 and radio1. Signed-off-by: Oever González <notengobattery@gmail.com>
* ipq40xx: add support for ASUS LyraMarius Genheimer2019-02-144-4/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix ASUS RT-AC58U switch port numberingChristian Lamparter2019-02-051-5/+5
| | | | | | | | This patch fixes the ASUS' RT-AC58U port order by unifying the configuration with the NBG6617. Reported-by: Roberto Socrates (rtac58u-user on the forum) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: consolidate 02_network board defaultsChristian Lamparter2019-02-051-58/+66
| | | | | | | | This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Linksys EA6350v3Oever González2019-01-265-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 RAM: 256 MiB Samsung K4B2G1646F-BYK0 FLASH1: MX25L1605D 2 MB FLASH2: Winbond W25N01GV 128Mb ETH: Qualcomm QCA8075 WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Reset LED: Status - Green SERIAL: Header at J19, Beneath DC Power Jack 1-VCC ; 2-TX ; 3-RX; 4-GND; Serial 115200-8-N-1. Tested and working: - USB (requires extra packages) - LAN Ethernet (Correct MAC-address) - WAN Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from Web UI - OpenWRT sysupgrade - LED - Reset Button Need Testing: - WPS button Install via Web UI: - Attach to a LAN port on the router. - Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login - Select the connectivity tab on the left - In the manual update box on the right - Select browse, and browse to openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin - Click update. - Read and accept the warning - The router LED will start blinking. When the router LED goes solid, you can now navigate to 192.168.1.1 to your new OpenWrt installation. Sysupgrade: - Flash the sysupgrade image as usual. Please: try to do a reset everytime you can (doing it with LuCI is easy and can be done in the same step). Recovery (Automatic): - If the device fails to boot after install or upgrade, whilst the unit is turned on: 1 - Wait 15 seconds 2 - Switch Off and Wait 10 seconds 3 - Switch on 4 - Repeat steps 1 to 3, 3 times then go to 5. 5 - U-boot will have now erased the failed update and switched back to the last working firmware - you should be able to access your router on LAN. Recovery (Manual): - The steps for manual recovery are the same as the generic u-boot tftp client method. Back To Stock: - Use the generic recovery using the tftp client method to flash the "civic.img". Also you can strip-and-pad the original image and use the generic "mtd" method by flashing over the "kernel" partition. * Just be careful to flash in the partition that the device is currently booted. Signed-off-by: Ryan Pannell <ryan@osukl.com> Signed-off-by: Oever González <notengobattery@gmail.com> [minor edits, removed second compatible of nand, added dtb entry to 4.19] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: remove misplaced MR33 UCI definitionDavid Bauer2019-01-261-3/+0
| | | | | | | | | | | This removes the misplaced UCI-network configuration for the MR33. The LAN port is set in 01_leds while it is already correctly defined in 02_network. This was most likely an oversight as no network configuration belongs into 01_leds. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: convert to device-tree based USB LED triggerChristian Lamparter2018-12-271-2/+0
| | | | | | | | Thanks to the ledtrig-usb.c the USB LED trigger can be setup in the device-tree definition for the Asus RT-AC58U and ZyXEL NBG6617. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: integrate ath10kcal_patch_mac into ath10kcal_patch_mac_crcChristian Lamparter2018-12-151-17/+11
| | | | | | | | | | | | | | | In the thread: "ipq806x: add ath10k calibration data MAC addresses patching" Chuanhong Guo <gch981213@gmail.com> noted that: "All ath10k calibration data have a checksum at 0x2. ath10kcal_patch_mac works for QCA9880/QCA9882 only because the ath10k firmware for these two chips doesn't check the checksum value. (QCA proprietary driver checks this and refuses to use caldata with incorrect checksum.)" This patch updates 11-ath10k-caldata of the ipq40xx target accordingly. Reported-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic ↵Petr Štetiar2018-12-061-45/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | diag.sh I wanted to add status LEDs support to my imx6 based board and have found out, that I could use diag.sh script found in ramips platform, which seems to be also shared in a few other platforms: 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh And @chunkeey suggested to me, that I can also add lantiq, ipq806x and apm821xx to the list of platforms which could share this generic diag.sh. I've extended the base diag.sh in a way, that if it detects any of the DTS LED aliases, then it would use the generic DTS set_led_state code. The code in platform's diag.sh has moved to base-files package in this commit: base-files: diag.sh: Make it more generic towards DTS so it could be reused Signed-off-by: Petr Štetiar <ynezz@true.cz> Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
* ipq40xx: fix openmesh sysupgrade with tar content out of orderMarek Lindner2018-12-051-3/+3
| | | | | | | | | | | | The tar extraction depends on the order in which the files are added to the tar file. Since the order is not guaranteed and depends on the host system, the combined mtd write fails with sysupgrade images built on some systems. Fix by changing to tar file order independent mtd write. Fixes: 86e18f6706e1 ("ipq806x: add support for OpenMesh A42") Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for EnGenius EAP1300Steven Lin2018-12-053-6/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin <steven.lin@senao.com>
* ipq40xx: fix NBG6617 LED mappingDavid Bauer2018-11-051-3/+3
| | | | | | | | The NBG6617's LEDs are wrongly identified in the 01_leds boardinit script (board instead of boardname), resulting in referencing non-existent LEDs in UCI. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: Create /var/lock directory in platform_do_upgrade_*Sven Eckelmann2018-10-071-8/+1
| | | | | | | | | | | | | | | | | | The sysupgrade_pre_upgrade hook was removed with 5e1b4c57ded7 ("base-files: drop fwtool_pre_upgrade") while there were still scripts using it: * target/linux/ar71xx/base-files/lib/upgrade/allnet.sh * target/linux/ar71xx/base-files/lib/upgrade/openmesh.sh * target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh Not running the hooks can either prevent a successful upgrade or brick the device because the fw_setenv program cannot be started correctly. Instead of adding this hook again, the directory /var/lock for fw_setenv can also just be created directly before fw_setenv is called. Fixes: 5e1b4c57ded7 ("base-files: drop fwtool_pre_upgrade") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* treewide: drop unused get_status_led functionsMathias Kresin2018-08-161-4/+0
| | | | | | | The function isn't used for targets getting the status leds from the devicetree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix upgrade led handlingMathias Kresin2018-08-161-2/+4
| | | | | | | | | | | | The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: consolidate upgrade state setMathias Kresin2018-08-161-6/+0
| | | | | | | | | | Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add support for the ZyXEL NBG6617Christian Lamparter2018-06-266-0/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ZyXEL NBG6617 Hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz NOR: 32 MiB Macronix MX25L25635F ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS Serial: WARNING: The serial port needs a TTL/RS-232 3.3v level converter! The Serial setting is 115200-8-N-1. The 1x4 .1" header comes pre-soldered. Pinout: 1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX first install / debricking / restore stock: 0. Have a PC running a tftp-server @ 192.168.1.99/24 1. connect the PC to any LAN-Ports 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file into the tftp-server root directory and rename it to just "ras.bin". 3. power-cycle the router and hold down the the WPS button (for 30sek) 4. Wait (for a long time - the serial console provides some progress reports. The u-boot says it best: "Please be patient". 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs flashes fast at the same time. You have to reboot the device and it should then come right up. Installation via Web-UI: 0. Connect a PC to the powered-on router. It will assign your PC a IP-address via DHCP 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234) 2. Go to the "Expert Mode" 3. Under "Maintenance", select "Firmware-Upgrade" 4. Upload the OpenWRT factory image 5. Wait for the Device to finish. It will reboot into OpenWRT without any additional actions needed. To open the ZyXEL NBG6617: 0. remove the four rubber feet glued on the backside 1. remove the four philips screws and pry open the top cover (by applying force between the plastic top housing from the backside/lan-port side) Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6617> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6617> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6617> ATSE NBG6617 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6617> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6617> ATGU |NBG6617# Co-authored-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-183-1/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
* ipq40xx: add get_status_led to diag.shDavid Bauer2018-06-181-0/+4
| | | | | | | | | | | This commit adds the get_status_led method to diag.sh, which sets the boot-led as status-led for scripts using this method to get a status-led. This method is used platform-independent in downstream project gluon to set the LED used to indicate the config-mode. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for OpenMesh A62Sven Eckelmann2018-04-234-4/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: add support for Netgear EX6100v2/EX6150v2David Bauer2018-04-133-2/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for 8devices JalapenoRobert Marko2018-04-133-8/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for 8devices Jalapeno. Specification: QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz 256 MB of DDR3 RAM 8 MB of SPI NOR flash 128 MB of Winbond SPI NAND flash WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN) phy@mdio3: Label: eth0 gmac0 phy@mdio4: Label: eth1 gmac1 Installation instructions: Since boards ship with old version of LEDE installation is simple. Just use sysupgrade -n -F sysupgrade.bin Syuspgrade needs to be forced since OpenWRT uses DT detection in recent releases. If you get error that FIT configuration is not found during boot it is due to older U-boot used on your board. That is because 8devices used custom FIT configuration partition name as they internally had v1 and v2 boards. Only v2 boards are sold so now they are shipping boards with never U-boot using generic config@1 FIT partition name. Also for old uboot it is possible to force loading config@1 by changing uboot environment: setenv boot5 'bootm 0x84000000#config@1’ saveenv Signed-off-by: Robert Marko <robimarko@gmail.com>