aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add support for Teltonika RUTX50David Bauer2023-07-263-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M Flash: 16MB SPI-NOR (W25Q128) 128MB SPI-NAND (XTX) WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac) ETH: 4x LAN ; 1x WAN (Gigabit) CELL: Quectel RG501Q 3G/4G/5G UART: Available on the goldfinger connector (Pinout silkscreened) 115200 8N1 3V3 - Only connect RX / TX / GND Installation ------------ 1. Enable SSH in the Teltonika UI (System --> Administration --> Access Control) 2. Check from which partition set the device is currently running from. $ cat /proc/boot_info/rootfs/primaryboot In case this output reads 0, install a Software update from Teltonika first. After upgrade completion, check this file now reads 1 before continuing. 2. Transfer the OpenWrt factory image to the device using scp. Use the same password (user root!) as used for the Web-UI. $ scp -O openwrt-factory.bin root@192.168.1.1:/tmp 3. Connect to the device using ssh as the root user. 4. Install OpenWrt by writing the factory image to flash. $ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin 5. Instruct the bootloaer to boot from the first partition set. $ echo 0 > /proc/boot_info/rootfs/primaryboot $ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin $ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin $ mtd write /tmp/bootconfig.bin /dev/mtd2 $ mtd write /tmp/bootconfig1.bin /dev/mtd3 6. Reboot the device. $ reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 844bb4bfad84cc6267f9b138d1f63b07ed3b77d0)
* ipq4019: add support for ZTE MF287+ aka DreiNeoAndreas Böhler2023-07-012-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit f70ee53b08466f612546f699c556cbdaa39e1466)
* ipq40xx: convert Buffalo WTR-M2133HP to DSAYanase Yuki2023-06-081-0/+1
| | | | | | | This commit convert WTR-M2133HP to DSA setup. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp> (cherry picked from commit edb3a4162c0763ecc9d5e7660700a68a25bf28e3)
* ipq40xx: add e2600ac c2 to dsa张 鹏2023-05-311-0/+3
| | | | | | | | | Convert E2600ac c2 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 0dca52cf595cedcabec5d384ddc83f1954cca46d)
* ipq40xx: add e2600ac c1 to dsa张 鹏2023-05-311-0/+3
| | | | | | | | | Convert E2600ac c1 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 7f2ecab0f4623e9b437b1a6656275695ac063fe4)
* ipq40xx: convert EZVIZ CS-W3-WD1200G-EUP to DSAChristian Lamparter2023-05-201-0/+1
| | | | | | Convert the repeater to DSA. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: convert AVM FRITZ!Repeater 3000 to DSANick Hainke2023-05-031-0/+1
| | | | | | Convert the repeater to DSA. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: convert GL-AP1300 to DSANick Hainke2023-04-242-1/+2
| | | | | | | | | | Convert GL-AP1300 to DSA and enable it. While working on it rename the GL-AP1300 leds from green to white. Tested-by: Rob White <rob@blue-wave.net> Tested-by: Robert Sommer <frauhottelmann@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: convert AP-365 to DSADavid Bauer2023-04-151-0/+1
| | | | | | | | | Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as the board design is pretty much the already updated AP-303. Run-tested on the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: fix Linksys upgrade, restore config stepMichael Trinidad2023-04-111-1/+1
| | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx and ipq806x devices using the linksys.sh script. Fixes: 8634c1080d50 ("ipq40xx: Fix Linksys upgrade, restore config step") Fixes: 2715aff5df83 ("ipq806x: Fix Linksys upgrade, restore config step") Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
* ipq40xx: Fix Linksys upgrade, restore config stepJeff Kletsky2023-03-261-1/+6
| | | | | | | | | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This was restored for some devices in commit 84ff6c90dda1 ("base-files: bring back nand_do_upgrade_success"). This restored preservation of config for ipq40xx devices using the linksys.sh script. Other devices and targets have not been examined. Closes: #11677 Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code") Tested-on: EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> (checkpatch nitpick) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Wallystech DR40x9Robert Marko2023-03-213-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* ipq40xx: convert Netgear EX6100/EX6150 v2 to DSADavid Bauer2023-03-081-1/+3
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: replace /sys/devices/virtual/ubi by /sys/class/ubiDaniel Golle2023-02-151-1/+1
| | | | | | | | | | Starting from Linux Kernel version 6.3 UBI devices will no longer be considered virtual, but rather have an MTD device parent. Hence they will no longer be listed under /sys/devices/virtual/ubi which is used in multiple places in OpenWrt. Prepare for future kernels by using /sys/class/ubi instead of /sys/devuces/virtual/ubi. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: convert Extreme AP3915i to DSAJames Andrewartha2023-01-171-0/+1
| | | | | | Convert and re-enabled Extreme AP3915i to DSA. Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
* ipq40xx: add DSL support for FritzBox 7530Martin Schiller2023-01-162-3/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set up MAC, LED, settings and default packages for DSL usage, similar to the lantiq target. Due to licensing uncertainty, we do not include the firmware files for the DSL drivers. To have a working DSL setup, follow the instructions below. Download the firmware files locally: mkdir -p files/lib/firmware/09a9 wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin For people building their own images: Run the above commands in the root of your local OpenWrt clone, and the firmware files will be part of the resulting images. For people downloading images: Copy the firmware files onto the router once it's booted up: scp -O -r files/lib/firmware root@fritz:/lib Reboot the device afterwards. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> [cleaned up] Signed-off-by: Andre Heider <a.heider@gmail.com> [set up LED] Signed-off-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: add support for Linksys WHW03 V2Vincent Tremblay2023-01-153-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: Add support ZTE MF18AMarcin Gajda2023-01-142-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* ipq40xx: sysupgrade: allow flashing Linksys factory firmwareTony Ambardar2022-12-311-0/+18
| | | | | | | | | | | | | | | | | Allow forced flashing of a factory firmware image, after checking for the correct FIT magic header and Linksys board-specific footer. Details of the footer are already described in scripts/linksys-image.sh. This is convenient as it avoids using a TFTP server or OEM GUI, and allows restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA migration and kernel repartition) directly from the command line. Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> # WHW01 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: migrate Linksys WHW01 to DSA and re-enableTony Ambardar2022-12-311-0/+3
| | | | | | | | | Convert Linksys WHW01 network configuration to DSA and re-enable builds. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix up Linksys WHW01 board name, device definitionTony Ambardar2022-12-312-2/+2
| | | | | | | | | | | | | | Update the board name defined in DTS to match online documentation and the name encoded into factory firmware. This helps supports flashing firmware factory images using 'sysupgrade'. Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB instead of the correct 74 MB, and defines factory images which include extra adjustments/padding that do not match OEM factory images and may cause problems flashing. Update image size and build recipe to fix these. Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: re-enable EA6350v3, EA8300, MR8300 buildsTony Ambardar2022-12-311-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300, and correspondingly reduce the rootfs size by 2 MB: * modify partition definitions in related .dts files * modify device kernel/image sizes in generic.mk Update to compat-version 2.0 to force factory image usage on sysupgrade, noting the current version 1.1 is an unreleased update for DSA migration. Also update the compat-version message, explaining the need to run one of the following console commands to update U-Boot's kernel-size variable before flashing the OpenWrt factory image. fw_setenv kernsize 500000 # (OpenWrt command line) setenv kernsize 500000 ; saveenv # (U-Boot serial console) Finally, re-enable the 3 devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: convert Aruba AP-303H to DSA and enable target againNick Hainke2022-12-291-0/+1
| | | | | | | | | The target was disabled since noone did the DSA conversion. Add the conversion and enable it again. Tested-by: John Walshaw <jjw@myself.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6Alexander Couzens2022-11-274-7/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP with a miniPCIe slot for a LTE modem. The wAP R AC is similar to the wAP AC but with the miniPCIe slot. The wAP R AC requires installing a LTE modem. The wAP LTE and wAP LTE6 comes with a LTE modem installed. See https://mikrotik.com/product/wap_r_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless: - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports one with 802.3af/at PoE in - 1x Mini PCI-E port (USB2) Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ipq40xx: Convert plasmacloud,pa2200 to DSASven Eckelmann2022-11-131-1/+2
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa2200Sven Eckelmann2022-11-131-7/+2
| | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert plasmacloud,pa1200 to DSASven Eckelmann2022-11-131-0/+3
| | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa1200Sven Eckelmann2022-11-131-2/+0
| | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for openmesh,a62Sven Eckelmann2022-11-123-10/+0
| | | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for openmesh,a42Sven Eckelmann2022-11-123-4/+0
| | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a62 to DSASven Eckelmann2022-11-122-3/+6
| | | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a42 to DSASven Eckelmann2022-11-122-0/+10
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: D-Link DAP-2610: convert to DSAGuillaume Lefebvre2022-11-121-0/+1
| | | | | | | Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
* ipq40xx: add support for GL.iNet GL-A1300Weiping Yang2022-11-092-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ipq40xx: add support for MikroTik hAP ac3 LTE6 kitCsaba Sipos2022-10-305-1/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD (hAP ac³ LTE6 kit), an indoor dual band, dual-radio 802.11ac wireless AP with built-in Mini PCI-E LTE modem, one USB port, five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac3_lte6_kit for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port - 1x USB Type A port - 1x Mini PCI-E port (supporting USB) - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6) Installation: Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6). 0. Export your MikroTik license key (in case you want to use the device with RouterOS later) 1. Boot the initramfs image via TFTP 2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder 3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin 4. Recovery to factory software is possible via Netinstall: https://help.mikrotik.com/docs/display/ROS/Netinstall Signed-off-by: Csaba Sipos <metro4@freemail.hu>
* ipq40xx: convert to DSA and enable Netgear Orbi devicesDavide Fioravanti2022-10-251-0/+10
| | | | | | | | | | Convert to DSA and enable again Netgear Orbi devices: - RBR50 - RBS50 - SRR60 - SRS60 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ipq40xx: Convert Google Wifi to DSA, reenableBrian Norris2022-10-231-0/+5
| | | | | | | | | | | | | | | | Undo parts of these: 116feb4a1cad ipq40xx: remove non-converted network configs db19efee9512 ipq40xx: disable boards not converted to DSA Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock bootloader has memorized them (instead of following aliases); then plug the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the 'local-mac-address' property is no longer in the correct node. Cc: David Bauer <mail@david-bauer.net> Cc: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* ipq40xx: convert to DSA and enable mobipromo,cm520-79fJack Chen2022-10-232-4/+5
| | | | | | | Convert to DSA and enable the MobiPromo CM520-79F device again. Signed-off-by: Jack Chen <redchenjs@live.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: convert to DSA and enable asus,rt-ac42uChen Minqiang2022-10-223-6/+16
| | | | | | | This convert board asus,rt-ac42u to DSA and re-enable it Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ipq40xx: Convert mikrotik,wap-ac to DSAMark Mentovai2022-10-192-4/+7
| | | | | | | | | | | | | | | | | | As done previously, this preserves the MAC addresses of they physical Ethernet ports. The interfaces are renamed as eth0 is in use for the native GMAC; the new interface naming matches the physical port labels. - sw-eth1 corresponds to the physical port labeled ETH1 and has the base MAC address. This port can be used to power the device. - sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC address one greater than the base. As this device has 2 physical ports, they are each connected to their respective PHYs, allowing the link status to be visible to software. Since they are not marked on the case with any role (such as LAN or WAN), both are bridged to the lan network by default, although this can easily be changed if needed. Signed-off-by: Mark Mentovai <mark@mentovai.com>
* ipq40xx: convert to DSA and enable Sony NCP-HG100/CellularINAGAKI Hiroshi2022-10-092-2/+3
| | | | | | | This patch converts networking on Sony NCP-HG100/Cellular to DSA and re-enables support for the device. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq40xx: ZTE MF289F: convert to DSADirk Buchwalder2022-10-091-6/+2
| | | | | | | | | Convert ZTE MF289F device to DSA, re-order network ports to match the labels on the case and re-enable the device. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de> Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: pakedge_wr-1: convert to DSATomasz Maciej Nowak2022-10-051-0/+1
| | | | | | | | | Convert pakedge_wr-1 device to DSA and enable it. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>i [ improve commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: luma_wrtq-329acn: convert to DSATomasz Maciej Nowak2022-10-051-0/+1
| | | | | | | | | Convert luma_wrtq-329acn device to DSA and enable it. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> [ improve commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: remove non-converted network configsRobert Marko2022-10-021-96/+0
| | | | | | | Remove networking configs for non DSA converted boards in ipq40xx. Currently, they are just causing clutter. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: Meraki MR33: convert MAC addresses to nvmemLech Perczak2022-10-022-8/+0
| | | | | | | | This fixes assigning random MAC to br-lan interface upon boot. While at that, rename at24@50 node to eeprom@50, to align with upstream device tree style. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: convert some boards to DSARobert Marko2022-10-025-85/+73
| | | | | | | | | | | | Convert IPQ40xx boards to DSA setup. Signed-off-by: Leon M. George <leon@georgemail.eu> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org> Signed-off-by: ChunAm See <z1250747241@gmail.com> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Andrew Sim <andrewsimz@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: Add ZTE MF289FGiammarco Marzano2022-09-243-3/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Sony NCP-HG100/CellularINAGAKI Hiroshi2022-09-246-1/+110
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac (WiFi-5) wireless function, based on IPQ4019. Specification: - SoC : Qualcomm IPQ4019 - RAM : DDR3 512 MiB (H5TC4G63EFR) - Flash : eMMC 4 GiB (THGBMNG5D1LBAIT) - WLAN : 2.4/5 GHz 2T2R (IPQ4019) - Ethernet : 10/100/1000 Mbps x2 - Transceiver : Qualcomm QCA8072 - WWAN : Telit LN940A9 - Z-Wave : Silicon Labs ZM5101 - Bluetooth : Qualcomm CSR8811 - Audio DAC : Realtek ALC5629 - Audio Amp. : Realtek ALC1304 - Voice Input Processor : Conexant CX20924 - Micro Controller Unit : Nuvoton MINI54FDE - RGB LED, Fan, Temp. sensors - Touch Sensor : Cypress CY8C4014LQI - RGB LED driver : TI LP55231 (2x) - LEDs/Keys : 11x, 6x - UART : through-hole on PCB - J1: 3.3V, TX, RX, GND from tri-angle marking - 115200n8 - Power : 12 VDC, 2.5 A Flash instruction using initramfs image: 1. Prepare TFTP server with the IP address 192.168.132.100 and place the initramfs image to TFTP directory with the name "C0A88401.img" 2. Boot NCP-HG100/Cellular and interrupt after the message "Hit any key to stop autoboot: 2" 3. Perform the following commands and set bootcmd to allow booting from eMMC setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000" saveenv 4. Perform the following command to load/boot the OpenWrt initramfs image tftpboot && bootm 5. On the initramfs image, perform sysupgrade with the sysupgrade image (if needed, backup eMMC partitions by dd command and download to other place before performing sysupgrade) 6. Wait for ~120 seconds to complete flashing Known issues: - There are no drivers for audio-related chips/functions in Linux Kernel and OpenWrt, they cannot be used. - There is no driver for MINI54FDE Micro-Controller Unit, customized for this device by the firmware in the MCU. This chip controls the following functions, but they cannot be controlled in OpenWrt. - RGB LED - Fan this fan is controlled automatically by MCU by default, without driver - Thermal Sensors (2x) - Currently, there is no driver or tool for CY8C4014LQI and cannot be controlled. It cannot be exited from "booting mode" and moved to "normal op mode" after booting. And also, the 4x buttons (mic mute, vol down, vol up, alexa trigger) connected to the IC cannot be controlled. - it can be exited from "booting mode" by installing and executing i2cset command: opkg update opkg install i2c-tools i2cset -y 1 0x14 0xf 1 - There is a connection issue on the control by uqmi for the WWAN module. But modemmanager can be used without any issues and the use of it is recommended. - With the F2FS format, too many errors are reported on erasing eMMC partition "rootfs_data" while booting: [ 1.360270] sdhci: Secure Digital Host Controller Interface driver [ 1.363636] sdhci: Copyright(c) Pierre Ossman [ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO ... [ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 1.528325] mmc0: new HS200 MMC card at address 0001 [ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB [ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB [ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB [ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0) [ 1.550323] Alternate GPT is invalid, using primary GPT. [ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 ... [ 8.841400] mount_root: loading kmods from internal overlay [ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 9.240465] block: attempting to load /etc/config/fstab [ 9.246722] block: unable to load configuration (fstab: Entry not found) [ 9.246863] block: no usable configuration [ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet [ 9.438915] urandom_read: 5 callbacks suppressed [ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read) [ 12.243332] mmc_erase: erase error -110, status 0x800 [ 12.246638] mmc0: cache flush error -110 [ 15.134585] mmc_erase: erase error -110, status 0x800 [ 15.135891] mmc_erase: group start error -110, status 0x0 [ 15.139850] mmc_erase: group start error -110, status 0x0 ...(too many the same errors)... [ 17.350811] mmc_erase: group start error -110, status 0x0 [ 17.356197] mmc_erase: group start error -110, status 0x0 [ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00 [ 17.446910] mmc0: tuning execution failed: -5 [ 17.447111] mmc0: cache flush error -110 [ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint [ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b [ 18.198691] block: attempting to load /etc/config/fstab [ 18.198972] block: unable to load configuration (fstab: Entry not found) [ 18.203029] block: no usable configuration [ 18.211371] mount_root: overlay filesystem has not been fully initialized yet [ 18.214487] mount_root: switching to f2fs overlay So, this support uses ext4 format instead which has no errors. Note: - The primary uart is shared for debug console and Z-Wave chip. The function is switched by GPIO15 (Linux: 427). value: 1: debug console 0: Z-Wave - NCP-HG100/Cellular has 2x os-image pairs in eMMC. - 0:HLOS, rootfs - 0:HLOS_1, rootfs_1 In OpenWrt, the first image pair is used. - "bootipq" command in U-Boot requires authentication with signed-image by default. To boot unsigned image of OpenWrt, use "mmc read" and "bootm" command instead. - This support is for "Cellular" variant of NCP-HG100 and not tested on "WLAN" (non-cellular) variant. - The board files of ipq-wifi may also be used in "WLAN" variant of NCP-HG100, but unconfirmed and add files as for "Cellular" variant. - "NET" LED is used to indicate WWAN status in stock firmware. - There is no MAC address information in the label on the case, use the address included in UUID in the label as "label-MAC" instead. - The "CLOUD" LEDs are partially used for indication of system status in stock firmware, use they as status LEDs in OpenWrt instead of RGB LED connected to the MCU. MAC addresses: LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex)) WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex)) 2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex)) 5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex)) partition layout in eMMC (by fdisk, GPT): Disk /dev/mmcblk0: 7733248 sectors, 3776M Logical sector size: 512 Disk identifier (GUID): **** Partition table holds up to 20 entries First usable sector is 34, last usable sector is 7634910 Number Start (sector) End (sector) Size Name 1 34 1057 512K 0:SBL1 2 1058 2081 512K 0:BOOTCONFIG 3 2082 3105 512K 0:QSEE 4 3106 4129 512K 0:QSEE_1 5 4130 4641 256K 0:CDT 6 4642 5153 256K 0:CDT_1 7 5154 6177 512K 0:BOOTCONFIG1 8 6178 6689 256K 0:APPSBLENV 9 6690 8737 1024K 0:APPSBL 10 8738 10785 1024K 0:APPSBL_1 11 10786 11297 256K 0:ART 12 11298 11809 256K 0:HSEE 13 11810 28193 8192K 0:HLOS 14 28194 44577 8192K 0:HLOS_1 15 44578 306721 128M rootfs 16 306722 568865 128M rootfs_1 17 568866 3958065 1654M rootfs_data [initial work] Signed-off-by: Iwao Yuki <dev.clef@gmail.com> Co-developed-by: Iwao Yuki <dev.clef@gmail.com> [adjustments, cleanups, commit message, sending patch] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (dropped clk_unused_ignore, dropped 901-* patches, renamed key nodes, changed LEDs chan/labels to match func-en, made :net -> (w)wan leds) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: base-files: properly close caseTomasz Maciej Nowak2022-09-241-0/+1
| | | | | | | | Fix this occurrence during boot: /bin/board_detect: line 10: Unsupported: not found Fixes: 80baffd2aa91 (" ipq40xx: add support for Pakedge WR-1") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 02:55:15 +0000