aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: fix 4.14 ImageBuilder build woesChristian Lamparter2019-01-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | Robert Marko reported an issue with the current imagebuilder images: "Imagebuilder includes the new kmod-usb-dwc3-qcom USB driver package by default even on 4.14. [...] the current state imagebuilder can't build images under 4.14 at all as the kmod-usb-dwc3-qcom does not exist in it so it throws and error and exits." This patch reverts the Makefile to just kmod-usb-dwc3-of-simple and once the switch to 4.19 is done. It also removes the kmod-usb-phy-qcom-dwc3 as they only contain the usb-phy drivers for the ipq806x generation. Dynamic switching based on the KERNEL_PATCHVER is possible by using: $(if $(filter 4.14,$(KERNEL_PATCHVER)),kmod-usb-dwc3-of-simple,kmod-usb-dwc3-qcom) though it Fixes: 13321fa1429 ("ipq40xx: Use kmod-usb-dwc3-qcom by default") Fixes: 6e58fb2c33e ("ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom") Reported-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcomChristian Lamparter2018-12-271-0/+1
| | | | | | | | | | | | | | | | | | | | | Robert Marko <robimarko@gmail.com> noted in "ipq40xx: Use kmod-usb-dwc3-qcom by default": | Since 4.18 we cant use DWC3 OF Simple anymore so we | have to use kmod-usb-dwc3-qcom. This patch adds a TODO right next to the KERNEL_PATCHVER so it will be picked up when moving to 4.19. I would also like to point out: All users/devs that are compiling their own images from source and have a existing 4.14 config and want to switch to 4.19: Please drop kmod-usb-dwc3-of-simple and add kmod-usb-dwc3-qcom module package. Otherwise, the USB port on your router will no longer work. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: Use kmod-usb-dwc3-qcom by defaultRobert Marko2018-12-271-1/+1
| | | | | | | Since 4.18 we cant use DWC3 OF Simple anymore so we have to use kmod-usb-dwc3-qcom. Signed-off-by: Robert Marko <robimarko@gmail.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-1/+1
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mac80211: fix selecting of ath10k -ct firmwareHauke Mehrtens2018-09-271-1/+1
| | | | | | | There is not firmware file with -ct-ct postfix, remove one -ct. Fixes: 61b5b4971e7d ("mac80211: make ath10k-ct the default ath10k") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: make ath10k-ct the default ath10kJohn Crispin2018-09-261-2/+2
| | | | | | | | We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: unbundle firmware and board fileMathias Kresin2018-04-131-0/+1
| | | | | | | | | | | Don't select the firmware with the board file, it prevents an easy use of the -ct ath10k firmware. Select the firmware within the default packages instead. Remove the per device selection of the firmware now that it the firmware is selected by default. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13Christian Lamparter2018-03-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add targetJohn Crispin2018-03-141-0/+21
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>