aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm63xx/patches-4.4
Commit message (Collapse)AuthorAgeFilesLines
* brcm63xx: remove misleading warning about partial SPI NOR writesJonas Gorski2017-07-051-0/+33
| | | | | | | | The warning will be triggered by jffs2 or UBI, and partial writes are no issue for most flash chips. Fixes: 2a2b16210bbc ("brcm63xx: backport upstream solution for SPI message size limits") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: add support for the Actiontec R1000H gatewayAnthony Sepa2017-06-301-0/+50
| | | | | | | | | | | | | | | | | | | | | | | SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz) Flash size: 32MB (split 16/16 dual boot) RAM size: 64MB Wireless: BCM432x 802.11a/b/g/n(pci) Ethernet: Broadcom BCM53115 USB: 1 x USB 2.0 Known issues: - Unable to detect 53115 switch attached to MDIO. Not supported - No support for the cable port More info on the device and the research can be found at: http://www.actiontec.com/212.html Same FCC ID as: https://wikidevi.com/wiki/Actiontec_V1000H_(Telus) Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca> [jonas.gorski: fix commit subject/message] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: fix bcm6328 pinmux other registerJonas Gorski2017-06-301-1/+1
| | | | | | | The pinmux register is at relative offset 0x8, not 0xc. Fixes hang when trying to modify pins >= 32. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: probe SPI connected switches through DTJonas Gorski2017-06-1037-164/+96
| | | | | | Now that we can configure the switches through DT, do so. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: leds-bcm6328: fix signal assignments for leds 4~7Jonas Gorski2017-06-101-0/+34
| | | | | | Properly use modulus for bit calculation for LEDs 4 to 7. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: add pinctrl supportJonas Gorski2017-06-1027-36/+5214
| | | | | | | Add and enable pincontrol drivers, and update dts(i) files with appropriate hogs. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: backport upstream generic gpio changesJonas Gorski2017-06-105-19/+2727
| | | | | | Backport patches that add a data pointer to gpio_chip. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: drop support for specifying SPI flash part parsersJonas Gorski2017-06-045-85/+9
| | | | | | No need to keep this since we set them from device-tree. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: drop support for caldata in brcm63xxpartJonas Gorski2017-06-0410-369/+22
| | | | | | | Now that we always provide these partitions through DT, we don't need to pass their data through parser data from board files anymore. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: do not require fixed partitions when probing from DTJonas Gorski2017-06-041-1/+1
| | | | | | | | Allow the parser to be invoked from DT without fixed cfe/linux/nvram partitions. This allows flash to be probed from DT also for multi flash-size images. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: register SPI controllers through DTJonas Gorski2017-06-0417-32/+419
| | | | | | | Register SPI controllers through device tree. We will wire up the clocks at a later stage. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: backport upstream solution for SPI message size limitsJonas Gorski2017-06-0418-102/+1135
| | | | | | | Backport upstream solution for working around SPI controller maximum message sizes. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: update flash of_node patches to full patch setJonas Gorski2017-06-0410-2/+920
| | | | | | Fixes missing of_node for SPI flash probed through devicetree. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: CPVA502+: add SPROM wifiDaniel Gonzalez Cabanelas2017-02-2842-111/+118
| | | | | | | | | | Add SPROM wifi to the kernel board data. After this fix, the wifi won't work anyway due the lack of RAM memory (16 MB). It will throw a kernel panic when loading the b43 drivers. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* brcm63xx: fix external IRQ edge type senseDaniel Gonzalez Cabanelas2017-02-281-1/+1
| | | | | | | | | | Fix the register for configuring rising/falling edge Rising should be sense=1, and falling sense=0. The old driver used these values, but the new one have them flipped. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* brcm63xx: Add Observa VH4032N supportDaniel Gonzalez Cabanelas2017-02-091-0/+64
| | | | | | | | | | | | | Add support for the Observa Telecom VH4032N router. This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB host ports. The wifi chip is an onboard Broadcom BCM43222. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> [jonas.gorski: use gpio-hog instead of abusing ephy-reset] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: Neufbox 6: fix switch by probing through DTJonas Gorski2017-02-0943-208/+128
| | | | | | | | | | | | Probe the switch through DT instead of a platform device. This fixes probe, as GPIO offsets are now properly accounted for. Fixes the following issue: [ 0.802953] 8021q: 802.1Q VLAN Support v1.8 [ 0.810518] rtl8366_smi: gpio_request failed for 18, err=-517 Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: add support for Pirelli/ADB P.DG AV4202NPaul Wassi2017-02-091-0/+71
| | | | | | | This patch adds support for the ADB P.DG AV4202N aka Pirelli PRG AV4202N. Signed-off-by: Paul Wassi <p.wassi@gmx.at> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: setup internal switch leds for bcm6368Jonas Gorski2017-02-097-7/+34
| | | | | | Setup the GPIO_MODE register bits for used internal switch port leds. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: do a full reset phy cycleJonas Gorski2017-02-091-0/+28
| | | | | | Make sure we do a proper reset of the phy, if the phy reset is defined. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: implement gpio_to_irq for bcm63xx-gpioJonas Gorski2017-02-091-1/+13
| | | | | | | | | Add support for mapping some GPIO lines to IRQs. GPIO to IRQ mappings were found out through experimentation, helped by having the GPIO as output still toggling the IRQ input. Based-on: http://patchwork.ozlabs.org/patch/660534/ Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: fix external interrupts on BCM6318Jonas Gorski2017-02-091-7/+20
| | | | | | | | Setting the clear bit for an interrupt seems to cause interrupts to be deasserted again immediately. So unset the bit for BCM6318 to allow subsequent interrupts to still work. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: backport MIPS changes introducing a separate IRQ stackFelix Fietkau2017-01-151-1/+1
| | | | | | | | Prevents crashes when IRQs arrive when the current kernel stack context already contains deeply nested function calls, e.g. when stacking lots of network devices on top of each other Signed-off-by: Felix Fietkau <nbd@nbd.name>
* generic: mtd: backport SPI_NOR_HAS_LOCKVictor Shyba2017-01-031-1/+1
| | | | | | | | | This flag was added to 4.9 with upstream commit 76a4707de5e18dc32d9cb4e990686140c5664a15. Signed-off-by: Victor Shyba <victor1984@riseup.net> [refresh and adjust platform patches, fix commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: update kernel 4.4 to version 4.4.30Stijn Segers2016-11-021-1/+1
| | | | | | | | | | This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches. Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood. Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed by P. Wassi). Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* kernel: update kernel 4.4 to version 4.4.20Álvaro Fernández Rojas2016-09-151-1/+1
| | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on brcm2708 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: Backport pending appended DTB handling patchesDaniel Gimpelevich2016-09-121-2/+2
| | | | | | | | | | Backport patches from upstream Linux kernel which are making the kernel stores the appended dtb not in the same resisters as defined in the UHI specification, use a separate variable on MIPS. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [some modifications] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: mtd: backport Macronix sector size fixMathias Kresin2016-09-031-1/+1
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* brcm63xx: backport mtd of node changes from upstreamJonas Gorski2016-08-1312-23/+608
| | | | | | | Should fix parser data containing uninitialized values for of probed physmap flashes, which could break e.g. the redboot parser. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: update kernel 4.4 to version 4.4.15Hauke Mehrtens2016-07-131-1/+1
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm63xx: use upstreamed compatible name for the periph intcJonas Gorski2016-06-211-1/+1
| | | | | | | This makes the eventual migration to bmips easier, as dts files will require less changes. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: fix external IRQsDaniel Gonzalez2016-06-211-9/+9
| | | | | | | | | | | | | External IRQs are currently broken, fix the BCM6345_EXT_IRQ driver. Since the adoption of the new driver irq-bcm6345-ext, in Chaos Calmer, external IRQs don't work. It seems there were some minor errors at the initial development of the driver. This patch fixes the ticket https://dev.openwrt.org/ticket/21613 Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: add initial support for Netgear EVG2000Graham Fairweather2016-06-031-0/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear EVG2000 VoIP Gateway to the bcm63xx targets. This device was not sold to the general public, but rather is/was provided by telcos to customers in Sweden, Australia, Singapore and other parts of asia. Known issues: - Unable to detect 53115 switch. This appear to be a problem with probing for the PHY using MDIO and results in error 5. Doesn't seem to be a problem with the configuration, and could use someone with experience to have a look at it. - Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver fails to load the firmware for the 4322, so 802.11n is not supported. More info on the device and the research can be found at: https://wiki.openwrt.org/toh/netgear/evg2000 https://wikidevi.com/wiki/Netgear_EVG2000 https://github.com/Xotic750/mirror-lede/tree/evg2000 https://forum.openwrt.org/viewtopic.php?id=63950 Signed-off-by: Graham Fairweather <xotic750@gmail.com> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: set DSL-274XB-F1 ath9k LED as active highÁlvaro Fernández Rojas2016-06-0335-102/+103
| | | | | | D-Link DSL-274XB rev F1 has an active high ath9k LED. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: set HG556a A/B ath9k LED as active highÁlvaro Fernández Rojas2016-06-0324-61/+63
| | | | | | Huawei HG556a has an active high ath9k LED. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: add support for inverting ath9k LED polarityÁlvaro Fernández Rojas2016-06-032-9/+12
| | | | | | | Some devices with ath9k WiFi require changing the default active low polarity to high in order to correctly operate the WiFi status LEDs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: refresh kernel patches and configÁlvaro Fernández Rojas2016-06-033-4/+4
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: update kernel 4.4 to version 4.4.6Hauke Mehrtens2016-03-171-1/+1
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 49032
* kernel: update kernel 4.4 to version 4.4.3Hauke Mehrtens2016-02-252-4/+4
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48783
* brcm63xx: add support for Huawei HG622Jonas Gorski2016-01-181-0/+72
| | | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 48305
* brcm63xx: fix platform gpio lookups for gpios < 32Jonas Gorski2016-01-182-19/+10
| | | | | | | | | | | | | Overwriting static strings is never a good idea, especially expecting identical strings to be stored in different memory locations. This caused the lookups to always return the second chip's name. Fix this by just initializing the lookup with the right values, so we don't need to modify the strings at all. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 48303
* brcm63xx: add linux 4.4 supportJonas Gorski2015-12-02157-0/+15914
Only netboot tested. Flash at your own risk. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 47702
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-14 03:35:13 +0000