aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm63xx/dts
Commit message (Collapse)AuthorAgeFilesLines
* brcm63xx: Add Observa VH4032N supportDaniel Gonzalez Cabanelas2017-04-281-0/+102
| | | | | | | | | | | | | Add support for the Observa Telecom VH4032N router. This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB host ports. The wifi chip is an onboard Broadcom BCM43222. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> [jonas.gorski: use gpio-hog instead of abusing ephy-reset] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: Neufbox 6: fix switch by probing through DTJonas Gorski2017-02-131-0/+8
| | | | | | | | | | | | Probe the switch through DT instead of a platform device. This fixes probe, as GPIO offsets are now properly accounted for. Fixes the following issue: [ 0.802953] 8021q: 802.1Q VLAN Support v1.8 [ 0.810518] rtl8366_smi: gpio_request failed for 18, err=-517 Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: fix external interrupts on BCM6318Jonas Gorski2017-02-101-1/+1
| | | | | | | | Setting the clear bit for an interrupt seems to cause interrupts to be deasserted again immediately. So unset the bit for BCM6318 to allow subsequent interrupts to still work. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: Livebox 1: fix part probe nameDaniel Gonzalez Cabanelas2016-11-211-1/+1
| | | | | | | | Fix the DTS file for the Livebox 1 routers: - part probe wrong, it should be RedBoot (uppercase matters) Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: Livebox 1: fix led namingDaniel Gonzalez Cabanelas2016-11-211-5/+5
| | | | | | | | Fix the DTS file for the Livebox 1 routers: - leds are totally wrong, fix them. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: Livebox 1: use button 1 as failsafe buttonDaniel Gonzalez Cabanelas2016-11-211-3/+3
| | | | | | | | Fix the DTS file for the Livebox 1 routers: - no failsafe button, use button 1 for this purpose Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* treewide: dts: use keycode defines from input dt-bindingMathias Kresin2016-11-131-1/+1
| | | | | | | | | | | | | | | | | | | | | All compiled device tree files not mentioned are binary identical to the former ones. Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts. Due to the include of the input binding header, the BTN_* node names in: - ramips/GL-MT300A.dts - ramips/GL-MT300N.dts - ramips/GL-MT750.dts - ramips/Timecloud.dts will be changed by the compiler to the numerical equivalent. Move the binding include of lantiq boards to the file where they are used the first time to hint the user where the values do come from. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: dts: fix dtc compiler warningsMathias Kresin2016-11-124-4/+4
| | | | | | | | | | | Fixes invalid device tree parameters. Drop the mvsw61xx node used in mvebu device tree source files. It looks like some kind of ethernet switch cargo cult. Neither the marvell,88e6352 nor the marvell,88e6172 compatible strings can be found in any LEDE file or in the kernel sources. Signed-off-by: Mathias Kresin <dev@kresin.me>
* brcm63xx: fix CT-536p/CT-5621T supportDaniel Gonzalez2016-08-011-1/+1
| | | | | | | | | | | Fix support for the Comtrend CT-536+, CT-5361 and CT-5621T routers support. Currently the firmware is broken for these routers, because there is a missing bar in the code at the DTS file avoiding to match with DTS stuff at the kernel. This causes the router boots without ethernet connectivity. The status led also has a typo. Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: fix HG556a C buttondani2016-07-241-1/+1
| | | | | | | One button of the HG556a-C has the wrong GPIO pin defined in the dts file, fix it Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
* brcm63xx: fix CVG834G compatible stringJonas Gorski2016-07-091-1/+1
| | | | | | | The CVG834G claimed to be a BCM6348, but is actually BCM3368. Since we don't test against it, this was harmless. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: move the bootargs into the dtb filesJonas Gorski2016-06-2183-0/+334
| | | | | | Instead of using a fixed commandline, allow one per device. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: use upstreamed compatible name for the periph intcJonas Gorski2016-06-2110-10/+10
| | | | | | | This makes the eventual migration to bmips easier, as dts files will require less changes. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: add initial support for Netgear EVG2000Graham Fairweather2016-06-031-0/+103
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear EVG2000 VoIP Gateway to the bcm63xx targets. This device was not sold to the general public, but rather is/was provided by telcos to customers in Sweden, Australia, Singapore and other parts of asia. Known issues: - Unable to detect 53115 switch. This appear to be a problem with probing for the PHY using MDIO and results in error 5. Doesn't seem to be a problem with the configuration, and could use someone with experience to have a look at it. - Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver fails to load the firmware for the 4322, so 802.11n is not supported. More info on the device and the research can be found at: https://wiki.openwrt.org/toh/netgear/evg2000 https://wikidevi.com/wiki/Netgear_EVG2000 https://github.com/Xotic750/mirror-lede/tree/evg2000 https://forum.openwrt.org/viewtopic.php?id=63950 Signed-off-by: Graham Fairweather <xotic750@gmail.com> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: fix BCM3368 interrupt controller addressesJohn Crispin2016-03-101-2/+2
| | | | | | | | | Looks like the addresses for BCM3368 were wrongly defined when DT support was introduced. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 48980
* brcm63xx: add support for Huawei HG622Jonas Gorski2016-01-181-0/+74
| | | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 48305
* brcm63xx: Add NuCom R5010UNv2 supportJonas Gorski2015-12-021-0/+64
| | | | | | | | | | | | | | | | | This patch adds support for the NuCom R5010UNv2. It's a BCM6328 based board. It has an onboard BCM43217 wifi chip. For this wifi chip looks like the brcmsmac driver isn't still supported, b43 drivers are used for the profile of the router. It's worth mentioning this board was affected by a bug solved with https://dev.openwrt.org/changeset/46707 Tested-by: Angel Fontan <angel.fontan@gmail.com> Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 47697
* brcm63xx: fix BCM3368 external interruptsJonas Gorski2015-11-041-1/+1
| | | | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 47375
* brcm63xx: add Comtrend VR-3026e supportJonas Gorski2015-08-301-0/+88
| | | | | | | | | | Add support for Comtrend VR-3026e v1. The device is almost identical to the Comtrend VR-3025un. Signed-off-by: Martin Tesar <tesarmar@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46752
* brcm63xx: Add support for Plusnet 2704NJonas Gorski2015-08-051-0/+84
| | | | | | | | BCM6318: add support for Plusnet / Sagem 2704N (V1) Signed-off-by: Matt Goring <matt.goring@googlemail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46562
* brcm63xx: make use of dt-includesJonas Gorski2015-07-1678-184/+340
| | | | | | | | | Now that we have a dtc command that invokes the preprocessor, make use of it and replace the magic numbers with KEY_* defines. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46391
* brcm63xx: HG553 buttons supportJonas Gorski2015-07-161-0/+20
| | | | | | | | | This patch adds buttons support for Huawei EchoLife HG553. Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46388
* brcm63xx: swap a4001n power leds againJonas Gorski2015-06-301-5/+5
| | | | | | | | | | This partially reverts r44577 ("brcm63xx: fix DTS LEDs and buttons"). Fixes #19858. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46149
* brcm63xx: Add Huawei HG655b supportJonas Gorski2015-05-211-0/+110
| | | | | | | | | | | | | | | This patch adds support for the Huawei HG655b. Nothing much special in this router, it's just another BCM6368 with a Ralink RT3062 wifi chip and the calibration data embedded in the main flash chip at offset 0x7c0000. There is also configuration data used by the OEM firmware before the cal_data partition, this area is protected by the board_data partition in this patch. Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45708
* brcm63xx: fix bcm6348 ext irqc compatible nameJonas Gorski2015-04-271-1/+1
| | | | | | | | | This was a remnant of an old version. Reported-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45583
* brcm63xx: fix bcm3368.dtsi typo.Jonas Gorski2015-04-271-2/+2
| | | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45582
* brcm63xx: fix leds bcm963269bhrJonas Gorski2015-04-211-4/+4
| | | | | | | | Fix the led naming and gpios. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45558
* brcm63xx: add missing bcm96329bhr profile and dtsJonas Gorski2015-04-211-0/+36
| | | | | | | | Hopefully the last missing board. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45557
* brcm63xx: move DSL-275XB to DTJonas Gorski2015-03-301-0/+75
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45168
* brcm63xx: move bcm6318 reference boards to DTJonas Gorski2015-03-302-0/+100
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45167
* brcm63xx: move VG50 to DTJonas Gorski2015-03-301-0/+28
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45166
* brcm63xx: move V2110 to DTJonas Gorski2015-03-301-0/+69
| | | | | | | | Also readd image generation which was accidentally dropped in r43364. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45165
* brcm63xx: move RTA770(B)W to dtsJonas Gorski2015-03-252-0/+136
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44992
* brcm63xx: move MAGIC to dtsJonas Gorski2015-03-251-0/+70
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44991
* brcm63xx: move CPVA502+ to dtsJonas Gorski2015-03-251-0/+44
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44990
* brcm63xx: move dg834g v4 to dtsJonas Gorski2015-03-251-0/+66
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44989
* brcm63xx: move dsl-2640u to dtsJonas Gorski2015-03-251-0/+50
| | | | | | | | Also build image again(?). Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44988
* brcm63xx: move bcm963268bu_p300 to dtsJonas Gorski2015-03-251-0/+28
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44987
* brcm63xx: Add BT Home Hub 2A support.Jonas Gorski2015-03-251-0/+140
| | | | | | | | | | | | | | | | | | Support for the BT HomeHub 2.0 Type A. This router was manufactured by Thomson, and it's BCM6358 based. The leds are controled by two chained HC594, all working ok. The BCM5325 switch has the RESET# pin wired to the GPIO15, but currently there is no way to tell the b53 driver how to get this gpio number in brcm63xx, therefore swconfig won't use it when performing a switch reset. The patch was tested with several firmwares, and all except unsupported stuff (i.e xDSL) works pretty well. Tested-by: Tahir <tahir00ali@gmail.com> Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com> SVN-Revision: 44985
* brcm63xx: Add DGND3700 v1 / DGND3800B supportJonas Gorski2015-03-161-0/+110
| | | | | | | | | | | | | | | | | This adds support for the Netgear DGND3700 v1 and DGND3800B. DGND3700 v1 and DGND3800B are exactly the same router, only one difference, the factory firmware. This patch produces two factory firmwares for each router. The router includes an onboard NAND flash for extra storage. NAND is currently not supported in bcm63xx, so no code added for this part. The NOR flash (32MB) is enough for storing an openwrt firmware. Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com> [jogo: Add back commit message from v1] Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44831
* brcm63xx: fix 6368 cpu1 reg typoJonas Gorski2015-03-151-1/+1
| | | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44784
* brcm63xx: fix DTS LEDs and buttonsJonas Gorski2015-02-286-20/+68
| | | | | | | | | | | | | - A4001N/A4001N1: fix swapped green and red LEDs - CVG834G: add missing LED - RTA1320: reorder LEDs by GPIO# - V2500V: add missing LEDs and buttons - WAP-5813n: fix WPS button (GPIO 35) Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44577
* brcm63xx: backport and enable DT spi-gpio no CS supportJonas Gorski2015-02-273-12/+6
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 44570
* brcm63xx: move buttons and leds to dts filesJonas Gorski2015-02-2756-0/+2543
| | | | | | | | | | | | | | Register buttons and leds through DT for all available dts, and remove them from the board files. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> [jogo: remove leds/buttons from board files fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw comment out spi-gpio and associated leds] Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44566
* brcm63xx: probe gpio controllers through DTJonas Gorski2015-02-2710-0/+183
| | | | | | | | | | | | | | | | Add a generic mmio gpio controller based driver and probe it through device tree. Use aliases for base calculation until we converted all users to device tree or named gpios. Convert bcm63xx_enet's ephy-reset gpio to use a named gpio. While at it, remove the duplicate reset gpio defintion for livebox. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44565
* brcm63xx: convert BTV2500V to dtsJonas Gorski2015-02-271-0/+30
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44564
* brcm63xx: convert RTA1320 to dtsJonas Gorski2015-02-271-0/+30
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44563
* brcm63xx: convert RTA1025 to dtsJonas Gorski2015-02-271-0/+30
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44562
* brcm63xx: use dtb for cvg834gJonas Gorski2015-02-272-0/+105
| | | | | | | | | | | | | Add a dtsi for bcm3368, add a dts and profile for cvg834g, and convert it to use ImageDTB. Since HCS requires more arguments, enhance the max arguments of the call. The image name is intentionally left blank to prevent non-initramfs images to be built, as they currently contain no rootfs and consequently won't work. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44561
* brcm63xx: add dts and profile for LiveboxJonas Gorski2015-02-271-0/+15
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44559
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 15:09:16 +0000