openwrt/upstream - upstream openwrt

	Commit message (Collapse)	Author	Age	Files	Lines
*	bcm63xx: Add support for the T-Com Speedport W 500V.	Daniel Dickinson	2010-11-28	2	-1/+15
\| \| \| \| \| \| \| \| \| \|	Add support for the T-Com Speedport W 500V using a special tagged image as it identifies itself as a 96348GW, but has some gpios wired differently, and also has only one ethernet port without a switch attached to it. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> SVN-Revision: 24190
*	bcm63xx: Finalize support for DSL-274xB, rev C2.	Daniel Dickinson	2010-11-28	2	-0/+19
\| \| \| \| \| \| \| \| \| \| \| \|	The DSL-2740B/DSL-2741B rev C2 support was missing the board definition, resulting in a kernel panic on boot. This patch adds it, and also renames the generated image name to properly reflect that it is for the revision C2, and for both the DSL-2740B and DSL-2741B. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> SVN-Revision: 24188
*	bcm63xx: Allow 'colored' power leds.	Daniel Dickinson	2010-11-28	1	-1/+1
\| \| \| \| \| \| \| \| \| \| \|	Since some devices have more than one power led, they might be separated by their color in the name. To also allow them to be on after leaving preinit, set any status led starting with 'power' to on instead of only those with the exact name of 'power'. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> SVN-Revision: 24187
*	bcm63xx: Don't hardcode the switch ethernet interface in preinit.	Daniel Dickinson	2010-11-28	2	-10/+10
\| \| \| \| \| \| \| \| \| \|	Currently eth1 is hardcoded as the expected interface switches in diagmode. This patch replaces the eth1 with the ifname, and also directly tests if the interface specified by ifname has a switch attached. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> SVN-Revision: 24186
*	bcm63xx: Add defconfigs.	Daniel Dickinson	2010-11-28	2	-1/+18
\| \| \| \| \| \| \| \| \| \| \|	Port the mechanism for different default configurations from ar71xx and use the old configuration as the default configuration. This should have no functional differences to before. While we are at it, remove the obsolete nat option. Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com> SVN-Revision: 24185
*	base-files: diag.sh: For power button as preinit status led, end with led ↵	Daniel Dickinson	2010-08-02	1	-1/+5
\| \| \| \| \| \|	left on, not off SVN-Revision: 22466
*	base-files: brcm63xx.sh: Added comtrend (96348GW-11) to routers with buttons ↵	Daniel Dickinson	2010-08-02	1	-1/+6
\| \| \| \| \| \|	and leds on preinit SVN-Revision: 22465
*	brcm63xx: Fixed vlan packet leakage in preinit for known devices with a ↵	Daniel Dickinson	2010-05-30	4	-0/+97
\| \| \| \| \| \|	switch on eth1 (currently only 96348GW - Tecom 6x00) SVN-Revision: 21629
*	brcm63xx: Added preinit reset button module loading for devices known to ↵	Daniel Dickinson	2010-05-30	1	-0/+16
\| \| \| \| \| \|	support it and for which /lib/brcm63xx.sh has the definitions (currently only 96348GW - Tecom 6x00) SVN-Revision: 21628
*	brcm63xx: Added LED code for preinit (/etc/diag.sh) for 96348GW (Tecom 6x00)	Daniel Dickinson	2010-05-30	1	-0/+67
\| \| \| \|	SVN-Revision: 21627
*	brcm63xx: Added preinit board-type detection (currently only 96348GW - Tecom ↵	Daniel Dickinson	2010-05-30	2	-0/+35
\| \| \| \| \| \|	6x00) SVN-Revision: 21626
*	we are using the default-on trigger for power LEDs, no need to change their ↵	Florian Fainelli	2009-07-18	1	-12/+0
\| \| \| \| \| \|	state from userspace SVN-Revision: 16892
*	register GPIO-connected LEDs for known boards	Florian Fainelli	2009-07-18	1	-0/+12
\| \| \| \|	SVN-Revision: 16887
*	add support for sysupgrade (#5117)	Florian Fainelli	2009-05-17	1	-0/+16
\| \| \| \|	SVN-Revision: 15900
*	Make 4-port LAN and 1 port wan configurations work	Florian Fainelli	2008-11-26	1	-0/+19
	SVN-Revision: 13362