aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm47xx
Commit message (Collapse)AuthorAgeFilesLines
* brcm47xx: refresh patchesHauke Mehrtens2014-04-083-4/+4
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 40425
* brcm47xx: backport 3.14 patch for nvram GPIO pin readHauke Mehrtens2014-03-301-0/+30
| | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 40346
* brcm47xx: Name LEDs colors for Linksys E1000 V2.1Hauke Mehrtens2014-03-302-0/+26
| | | | | | | | | Handle it by creating a new patch for simple database changes. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 40345
* brcm47xx: update workarounds patch to V3Hauke Mehrtens2014-03-302-6/+18
| | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 40344
* kernel: update 3.10 to 3.10.34Gabor Juhos2014-03-272-8/+8
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 40291
* brcm47xx: add initial support for kernel 3.14Hauke Mehrtens2014-03-1222-0/+1958
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39905
* brcm47xx: explicitely mention MIPS to avoid confusionFlorian Fainelli2014-03-081-1/+1
| | | | | | | | | And while at it, fix the nomenclature, BCM947xx/953xx refer to specific boards, while BCM47xx/BCM53xx refer to chip identification number. Signed-off-by: Florian Fainelli <florian@openwrt.org> SVN-Revision: 39841
* brcm47xx: b44: some fixes in combination with the switchHauke Mehrtens2014-02-231-2/+26
| | | | | | | | | Let the switch start the carrier and set the duplex mode independently if this nic is up of not. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39733
* brcm47xx: b44: start the phyHauke Mehrtens2014-02-231-0/+23
| | | | | | | | | | | We did not start the PHY when an external phy was in use. Without this patch the driver uses half duplex mode and the switch uses full duplex mode, which causes problems. Thank you fback for spotting this problem. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39719
* brcm47xx: fix detection of some Linksys WRT54G* devicesHauke Mehrtens2014-02-233-6/+45
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39718
* kernel: update 3.10 to 3.10.32Gabor Juhos2014-02-231-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39707
* brcm47xx: new patch adding arch workarounds.cHauke Mehrtens2014-02-044-5/+77
| | | | | | | | | It was recently sent to linux-mips for comments. It adds workaround for WNR3500L to enable USB port. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 39469
* brcm47xx: use upstream patch removing WGT634U codeHauke Mehrtens2014-02-042-5/+27
| | | | | | | | It does the same, it just reorders things Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 39468
* brcm47xx: move OpenWrt arch patches a bit furtherHauke Mehrtens2014-02-043-0/+0
| | | | | | | | This allows picking more upstreamed stuff Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 39467
* kernel: ssb: update ssb to a version from kernel 3.14-rc1Hauke Mehrtens2014-02-042-480/+0
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39464
* kernel: bcma: update bcma to a version from kernel 3.14-rc1Hauke Mehrtens2014-02-042-242/+0
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39463
* kernel: update 3.10 to 3.10.28Gabor Juhos2014-01-262-3/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39399
* brcm47xx: add brcmsmac + bgmac profileHauke Mehrtens2014-01-121-0/+20
| | | | | | | Signed-off-by: Cody P Schafer <devel@codyps.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39258
* brcm47xx: parse model from cpuinfoHauke Mehrtens2014-01-121-3/+2
| | | | | | | | | Instead of looking into the proc entry provided by broadcom-diag use the board info from /proc/cpuinfo to get the board we are on. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39256
* brcm47xx: fix led indicationHauke Mehrtens2014-01-121-16/+26
| | | | | | | | | Use the new led api also on brcm47xx. The led for failsafe indication is searched for. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39255
* brcm47xx: fix network failsafe indicationHauke Mehrtens2014-01-123-75/+18
| | | | | | | | | | Remove the code used on the old switch driver. The Ethernet drive is loaded as a module and needs some time to get up therefor we added some wait function. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39254
* brcm47xx: do not use broadcom-diagHauke Mehrtens2014-01-121-1/+3
| | | | | | | | | This makes brcm47xx target use the default gpio led and button driver and not broadcom-diag any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39253
* brcm47xx: add new led and button supportHauke Mehrtens2014-01-1221-20/+2555
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39252
* brcm47xx: update some patches to versions in linux mainlineHauke Mehrtens2014-01-129-115/+315
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39251
* brcm74xx: fix patch for BCM4706 CPUsHauke Mehrtens2014-01-123-15/+46
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39250
* brcm47xx: update mtd driversHauke Mehrtens2014-01-127-35/+154
| | | | | | | | This backports some patches from linux upstream. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39249
* kernel: update 3.10 to 3.10.26Gabor Juhos2014-01-111-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 39220
* brcm47xx: fix cpu wait for BCM4706Hauke Mehrtens2013-12-263-19/+18
| | | | | | | | This was called to early. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39167
* brcm47xx: b44: This updates the phylib patches to the version send upstreamHauke Mehrtens2013-12-2615-165/+252
| | | | | | | | This uses a fixed phy instead of a dummy one. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39166
* brcm47xx: deactivate early printk supportHauke Mehrtens2013-12-154-52/+4
| | | | | | | | | This breaks some devices where the serial console is not at port 0 but somewhere else. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39060
* kernel: update kernel 3.10 to 3.10.24Hauke Mehrtens2013-12-151-1/+1
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 39059
* brcm47xx: misc cleanupsHauke Mehrtens2013-12-012-4/+2
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38980
* brcm47xx: deactivate mips wait instruction only for BCM4706Hauke Mehrtens2013-12-013-13/+27
| | | | | | | | | The wait instruction is only broken on the BCM4706 and not on the other similar SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38979
* brcm47xx: config: set CONFIG_HZ=100 and CONFIG_IP_ROUTE_VERBOSEHauke Mehrtens2013-12-011-4/+0
| | | | | | | | | This sets both values to the OpenWrt default values. There is no reason to use some brcm47xx specific values here. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38978
* brcm47xx: add vectored interruptsHauke Mehrtens2013-12-012-0/+67
| | | | | | | | | This adds support for vectored interrupts in this SoC. This is supported by the 74K cpus. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38975
* brcm47xx: add cpu overwritesHauke Mehrtens2013-12-012-14/+102
| | | | | | | | | | | | bcm47xx misses cpu overwrites for the features of the CPUs used in these SoCs. Instead of manually checking, it is now known at compile time for some options and the compiler is able to remove the checks and optimize the code. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38974
* brcm47xx: use "firmware" partition nameHauke Mehrtens2013-12-013-22/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Some time ago, after switching to the mainline bcm47xxpart driver following patch has been applied: commit 03cef8725d2062335ffc3de50fc037b294fd458c Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73> Date: Sat Apr 6 22:22:26 2013 +0000 brcm47xx: use old partition names again for kernel 3.8 This fixes sysupgrade. The partition names are used all over the Internet in various howtos. Thank you russell for spotting this problem. I propose to revert this change and make sysupgrade use "firmware" instead. This makes brcm47xx compatible with widely used ar71xx and after all "firmware" sounds like a much better name for... the firmware. This change doesn't affect "sysupgrade" usage, because it never takes a partition name as a parameter. This change only affects users using mtd tool directly. Hopefully there are not many howtos using "mtd" command. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 38973
* kernel: update 3.10 to 3.10.21Gabor Juhos2013-12-011-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38972
* brcm47xx: swap also early boot console if necessary.Hauke Mehrtens2013-11-132-2/+49
| | | | | | | | | | | Some devices are using tty1 as the default console, also swap the early boot console in such case. This is needed for the WGT634U. Thank you Russell for reporting this. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38794
* brcm47xx: fix netconfig for inverted vlan?ports in nvramHauke Mehrtens2013-11-111-2/+4
| | | | | | This was observed on the Belkin Share F7D7302. SVN-Revision: 38769
* linux/brcm47xx : Belkin F7Dx30x board detectionHauke Mehrtens2013-11-111-0/+33
| | | | | | | | | | | | | | | boardnum is unstable, so allow using NULL to make it unchecked. A method for differentiating F7D3301 from F7D3302 using nvram is unknown at this point. Reading the first 32bits of magic from the "linux" mtd partition would do the trick, but these 2 are similar enough that we don't need separate led/button definitions. Not knowing which one you have is only a usability issue for upgrading the device: they expect different magic numbers for their trx images. Signed-off-by: Cody P Schafer <devel@codyps.com> SVN-Revision: 38767
* brcm47xx: b44: fix logic in BUG_ON()Hauke Mehrtens2013-11-111-1/+1
| | | | | | | | It is a problem when phydev is not set at this position and not the other way around. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38744
* brcm47xx: add detection for Linksys WRT54GS V1Hauke Mehrtens2013-11-091-1/+12
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38700
* brcm47xx: register ADM6996L switchHauke Mehrtens2013-11-093-3/+127
| | | | | | | | | | | | This patch makes it possible to use adm6996.c on first generation BCM47XX devices with ADM switches. This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for the device. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38699
* brcm47xx: fix detection of Asus RT-N12B1 and Netgear WNR3500LHauke Mehrtens2013-11-051-1/+10
| | | | | | | | This closes #14367 and #14328. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38656
* kernel: update 3.10 to 3.10.18Gabor Juhos2013-11-051-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38652
* brcm47xx: b44: fix error handling for dummy phy creationHauke Mehrtens2013-10-251-24/+3
| | | | | | | | | When the mdio bus is unregistered the newly created phy will also be unregistered and freed. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38539
* brcm47xx: b44: add dummy phy device if we do not find anyHauke Mehrtens2013-10-251-0/+64
| | | | | | | | | | | On some devices with e.g. a BCM2535F switch the second MAC is used, but we can not find a phy under all addresses between 0 and 31, 0xffffffff is returned as phy id. If we can not find a phy at the expected address create a dummy one. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38538
* kernel: update 3.10 to 3.10.17Gabor Juhos2013-10-231-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 38506
* brcm47xx: b44: detect external phy by bit set in DevControl registerHauke Mehrtens2013-10-228-73/+147
| | | | | | | | | | Without this patch we treated only phy addr 30 as an external phy, but there is a register to check that. Now we do not have to try to reset the switch to check for an external switch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38502
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 09:06:03 +0000