aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm47xx
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.93Koen Vandeputte2019-01-152-21/+22
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* brcm47xx: Enable USB power on WNDR3400v3Tuomas Tynkkynen2018-12-181-0/+39
| | | | | | | | WNDR3400v3 needs GPIO 21 pulled high to enable power to USB ports. Add a kernel patch to do that. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> (backported from 5dd745588edea19846b2bc3a2e6938f139374ea9)
* kernel: bump 4.14 to 4.14.81Koen Vandeputte2018-11-141-4/+4
| | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed patches: - 081-spi-bcm-qspi-switch-back-to-reading-flash-using-smal.patch Altered patches: - 0054-cpufreq-dt-Handle-OPP-voltage-adjust-events Compile-tested on: cns3xxx, imx6, ipq806x, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.137Koen Vandeputte2018-11-141-4/+4
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed hunks: - 703-phy-support-layerscape.patch Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.71Koen Vandeputte2018-09-211-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.128Koen Vandeputte2018-09-211-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.68Koen Vandeputte2018-09-071-76/+0
| | | | | | | | | | | | | | | | Refreshed all patches. Remove upstream accepted: - 330-Revert-MIPS-BCM47XX-Enable-74K-Core-ExternalSync-for.patch Altered: - 303-v4.16-netfilter-nf_tables-remove-multihook-chains-and-fami.patch - 308-mips32r2_tune.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.125Koen Vandeputte2018-09-071-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* brcm47xx: cosmetic fix in model detectionPaul Wassi2018-08-131-1/+1
| | | | | | | | In "brcm47xx: rework model detection" the file 01_detect was moved to 01_network, therefore also update the warning message in case everything fails. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kernel: bump 4.14 to 4.14.60 for 18.06Stijn Segers2018-08-061-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Refreshed patches. * Patches made redundant by changes upstream: - target/linux/ramips/patches-4.14/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch * Patches accepted upstream: - target/linux/apm821xx/patches-4.14/020-0001-crypto-crypto4xx-remove-bad-list_del.patch - target/linux/apm821xx/patches-4.14/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch - target/linux/brcm63xx/patches-4.14/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - target/linux/brcm63xx/patches-4.14/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - target/linux/generic/backport-4.14/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch - target/linux/generic/pending-4.14/900-gen_stats-fix-netlink-stats-padding.patch The ext4 regression introduced in 4.14.55 has been fixed by 4.14.60 (commit f547aa20b4f61662ad3e1a2040bb3cc5778f19b0). Fixes the following CVEs: - CVE-2018-10876 - CVE-2018-10877 - CVE-2018-10879 - CVE-2018-10880 - CVE-2018-10881 - CVE-2018-10882 - CVE-2018-10883 Thanks to Stijn Tintel for the CVE list :-). Compile-tested on: ramips/mt7621, x86/64 Run-tested on: ramips/mt7621, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* kernel: bump 4.9 to 4.9.117 for 18.06Stijn Segers2018-08-061-2/+2
| | | | | | | | | | | | | | | | | | | | | | | * Refreshed patches. * Removed patches: - target/linux/ar71xx/patches-4.9/103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch superseded by upstream - target/linux/ar71xx/patches-4.9/403-mtd_fix_cfi_cmdset_0002_status_check.patch superseded by upstream - target/linux/brcm63xx/patches-4.9/001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch accepted upstream - target/linux/brcm63xx/patches-4.9/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch accepted upstream - target/linux/brcm63xx/patches-4.9/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch accepted upstream - target/linux/generic/pending-4.9/900-gen_stats-fix-netlink-stats-padding.patch * New backported patch to address ext4 breakage, introduced in 4.9.112: - backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9 Thanks to Koen Vandeputte for pointing out the need to add the ARM64_SSBD symbol, and the ext4 patch. Compile-tested on: ar71xx Run-tested on: ar71xx Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* brcm47xx: rework model detectionJo-Philipp Wich2018-07-302-18/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | On brcm47xx boards, the model ID is the combination of the "boardtype" nvram variable and an optional supplemental "boardnum" variable while the human readable model name is usually exposed in the "machine" field of the /proc/cpuinfo file. Move the extraction of the board nvram variables and model name string into the 01_sysinfo file and rework the 01_detect board configuration script to solely use the prepared sysinfo values without performing own detection logic. As a consequence, we can drop the ucidef_set_board_id() and ucidef_set_model_name() invocations in favor to the generic behaviour which copies the /tmp/sysinfo/{board_name,model} values into the board.json "id" and "name" fields respectively. Since "01_detect" only contains network configuration logic after this change, move it to "01_network" and rename the contained "detect_by_xxx" functions to "configure_by_xxx" instead, to avoid potential confusion. Fixes FS#1576 Acked-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Jo-Philipp Wich <jo@mein.io> (cherry picked from commit d7d10f2c1e8511fe07c9760e85f2272a85168f8d)
* brcm47xx: revert upstream commit breaking BCM4718A1Rafał Miłecki2018-07-271-0/+76
| | | | | | | This fixes kernel hang when booting on BCM4718A1 (& probably BCM4717A1). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 4c1aa64b4d804e77dfaa8d53e5ef699fcced4b18)
* kernel: bump 4.14 to 4.14.54 for 18.06Koen Vandeputte2018-07-121-2/+2
| | | | | | | | | | | | Refreshed all patches Reworked patches to match upstream: 335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.111 for 18.06Koen Vandeputte2018-07-121-2/+2
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.106 for 18.06Stijn Segers2018-06-071-4/+4
| | | | | | | | | | | Refreshed patches. The following patches were upstreamed and have been deleted: * target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch * target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch * target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch * target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* brcm47xx: add switch port mapping to Asus WL-500WMirko Parthey2018-05-241-1/+1
| | | | | | | | | | | | Switch ports 0..3 are connected to external ports LAN{1..4} in sequence, switch port 4 is not used, and switch port 5 is connected to the CPU. The WAN port is attached to the CPU's second network interface; it has no connection to the internal switch. Reuse the "Dell TrueMobile 2300" entry, which describes the same mapping. Signed-off-by: Mirko Parthey <mirko.parthey@web.de> (cherry picked from commit 7ac238fc9855d20f0cfbc5754a1f9591438abfe3)
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit 67a3cdcbb05559549985a189eabaf2df92559ed7)
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit bdc2b58c4bccb50242af853dc80b50f9324b841c)
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit a08b0d0c3149060f1585ad3ea2ea3edfde71bce4)
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit 978543a246c6badb5e5e1c2430211e01f005af27)
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-241-2/+0
| | | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit ead26e9db649a508ba93e7e8193ada70322620b1)
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit f928c338ad6c8215a5fe280473e37786157a2d05)
* kernel: bump 4.14 to 4.14.43 for 18.06Koen Vandeputte2018-05-241-4/+4
| | | | | | | | | | | | | | | | | | | | | Refreshed all patches Dropped upstreamed patches: 522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch 523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch 525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch 527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch updated patches: 524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch 030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718 Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* brcm47xx: switch to the kernel 4.14Rafał Miłecki2018-05-081-1/+1
| | | | | | | | | | | | | | | | | | The biggest (and the only?) disadventage of this is obviously an increased image size. For mips74k the size of vmlinux goes up from 4186684 B to 4701436 B. Most devices use LZMA compressed kernel so probably more important is vmlinux.lzma size which goes up from 1342945 B to the 1508498 B. Still this isn't something that should stop target kernel bump. There are various adventages of kernel 4.14. If kernel / image size is a serious concern for anyone, it's perfectly possible to use previous release which is pretty solid for the brcm47xx. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Cc: Paul Wassi <p.wassi@gmx.at> Cc: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: remove linux 4.4 supportFelix Fietkau2018-04-2725-2935/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.9 to 4.9.96Kevin Darbyshire-Bryant2018-04-261-1/+1
| | | | | | | | | | | | | | | | | | Refresh patches, following required reworking: ar71xx/patches-4.9/930-chipidea-pullup.patch layerscape/patches-4.9/302-dts-support-layercape.patch sunxi/patches-4.9/0052-stmmac-form-4-12.patch Fixes for CVEs: CVE-2018-1108 CVE-2018-1092 Tested on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Arjen de Korte <build+openwrt@de-korte.org>
* brcm47xx: backport upstream patches for Netgear WNR1000 V3Rafał Miłecki2018-04-2317-137/+383
| | | | | | This includes fix for reading NVRAM content. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 4.14 to 4.14.34Stijn Tintel2018-04-162-4/+4
| | | | | | | | | | | | | Refresh patches. Update patches that no longer apply: - backport/313-netfilter-remove-defensive-check-on-malformed-packet.patch - pending/642-net-8021q-support-hardware-flow-table-offload.patch Compile-tested: x86/64. Runtime-tested: x86/64. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* brcm47xx: add kernel 4.14 supportPaul Wassi2018-04-0322-0/+2685
| | | | | | | | | | | | | | Add patches for 4.14, drop patch 030 since it's already included upstream. Tested on: 1) WRT54GL (with RAM upgraded to 32 MiB) 2) WL500gPv2 (with RAM upgraded to 64 MiB) 3) BCM47186B0 SoC board 4) BCM4706 SoC board Signed-off-by: Paul Wassi <p.wassi@gmx.at> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* brcm47xx: add Luxul XAP-1500 and XWR-1750 WiFi LEDsRafał Miłecki2018-04-034-4/+176
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: unroll MIPS r4k cache blast functionFelix Fietkau2018-03-101-7/+48
| | | | | | | | | | | Optimize the compiler output for larger cache blast cases that are common for DMA-based networking. On ar71xx, I measured a routing throughput increase of ~8% Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com> Signed-off-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* brcm47xx: image: build firmware for Asus WL-500g DeluxeRafał Miłecki2017-12-291-0/+8
| | | | | | | | It's a device based on BCM5365P (0x5365 package 0x00). This SoC has USB 1.1 controller but device has two USB 2.0 parts. They are handled by PCI-based controllers: 1106:3038 UHCI and 1106:3104 EHCI. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* brcm47xx: remove versions from linksys-e1000 targetMoritz Warning2017-12-111-2/+2
| | | | | | | | | | The target name does not need to included a revision if all revisions are supported. This target supports all revisions (v1, v2, v2.1). Signed-off-by: Moritz Warning <moritzwarning@web.de> [Keep the version numbers in the device title, it doesn't harm] Signed-off-by: Mathias Kresin <dev@kresin.me>
* brcm47xx: use proper region code in image nameMoritz Warning2017-12-111-9/+9
| | | | | | | Replace 'north-america' by 'na' and remove 'other-regions' in image files for Netgear WGR614 v10. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* brcm47xx: fix switch port mapping on D-Link DIR-330Antony Black2017-11-161-0/+1
| | | | | | | | D-Link DIR-330 is clone of ASUS WL500GP2, by default conf the WAN port is eth1, it's not working cus eth1 not soldered and wan port function performs 5th port of the switch. Signed-off-by: Antony Black <gtrtfm@gmail.com>
* brcm47xx: fix switch port mapping on Asus RT-N16Tim Thorpe2017-11-101-1/+1
| | | | | | | On the Asus RT-N16, the ports are not mapped the in the same way as the RT-N12. It is, however, the same as the Linksys E3000v1. Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
* brcm47xx: use kernel 4.9 by defaultHauke Mehrtens2017-10-181-1/+1
| | | | | | | | Kernel 4.9 is now working on the brcm47xx boards, we just recently fixed the problem that some boards did not boot at all, by changing the memory regions used to relocate the kernel to in the loader. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: relocate the stack in loaderHauke Mehrtens2017-10-112-2/+4
| | | | | | | | | | | By default we are reusing the stack provided by CFE, like it is intended by CFE. On my WRT54GS it is located at 0x8043BF30, so a big kernel image could overwrite it. Relocate it to a different memory region which is still under the 8MB RAM, but in the higher area. We only need this memory region for the stack of the loader, Linux will set up this for its own. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: relocate loader to higher addressHauke Mehrtens2017-10-111-1/+1
| | | | | | | | | | | | | | | | | | | | | The boot process on a WRT54GL works the following way: 1. CFE gets loaded by the boot rom from flash 2. CFE loads the loader from the flash and gzip uncompresses it 3. CFE starts the loader 4. The loader stores the FW arguments and relocates itself to BZ_TEXT_START (now 0x80600000) 5. The loader reads the Linux image from flash 6. The loader lzma decompresses the Linux image to LOADADDR (0x80001000) 7. The loader executes the uncompress Linux image at LOADADDR The BZ_TEXT_START was set to 0x80400000 before. When the kernel gets uncompressed and is bigger than BZ_TEXT_START - LOADADDR it overwrote the loader which was currently uncompressing it and made the board crash. Increase the BZ_TEXT_START my 2 MB to have more space for the kernel. Even on 16MB RAM devices the memory goes till 0x80FFFFFF so this should not be a problem. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "brcm47xx: Fix sysupgrade with E1200v1"Hauke Mehrtens2017-09-251-1/+0
| | | | | | | | | | This reverts commit 31e9445b7e614f54daa0caf3148e223d088311ab. "Linksys E1200 V1" is not a valid board name, as the brcm47xx arch code can not detect this device. Stefan Lippers-Hollmann also found a typo in this patch "cybetran" instead of "cybertan". Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: Fix sysupgrade with E1200v1Rosen Penev2017-09-241-0/+1
| | | | | | Entry was missing for some reason. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* brcm47xx: fix switch port mapping on Asus RT-N12 and RT-N16 modelsJo-Philipp Wich2017-07-211-0/+2
| | | | | | | | | | | | | On Asus RT-N12 and RT-N16 models, the WAN and LAN4 ports are swapped in the initial switch configuration since the presets present in nvram appear to be wrong. Add special casing for these models to detect_by_model() in order to ensure a proper switch configuration. Fixes FS#502. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* treewide: use only board_name function to get nameMathias Kresin2017-07-151-1/+1
| | | | | | | | | | | | Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree compatible string directly. Always use the board_name function to get the board name. The admswconfig package still reads /proc/cpuinfo directly. The code looks somehow broken and the whole adm5120 which uses this package looks unmaintained. Leave it as it is for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: use the generic board_name functionMathias Kresin2017-07-151-5/+1
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: do board detection during preinitMathias Kresin2017-07-151-0/+12
| | | | | | Do the board detection during preinit to unify it across all targets. Signed-off-by: Mathias Kresin <dev@kresin.me>
* brcm47xx: Add support for kernel 4.9Hauke Mehrtens2017-07-0222-0/+2782
| | | | | | | I tested this on a WRT54GS and a WRT610N V1. The WRT610N does not boot when the kernel is too big, so I deactivated KALLSYMS Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: refresh kernel configurationHauke Mehrtens2017-07-021-8/+8
| | | | | | Run make kernel_oldconfig on the brcm47xx target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: remove kernel 4.1 supportHauke Mehrtens2017-07-0236-3487/+0
| | | | | | Kernel 4.1 is not supported by LEDE for some time now. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: use DMZ LED as status indicatorMirko Parthey2017-07-021-15/+7
| | | | | | | | | | | | | On the Linksys WRT54GSv1, the Power LED flickers in the "off" state. Indicate status using the DMZ LED if available, since it has solid "on" and "off" states. This change was tested on the WRT54GSv1, but may also affect other brcm47xx devices. Fixes FS#793. Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 17:40:36 +0000