| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
| |
This sets both values to the OpenWrt default values. There is no reason
to use some brcm47xx specific values here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38978 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
This adds support for vectored interrupts in this SoC.
This is supported by the 74K cpus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38975 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38699 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
This just add some bytes to the kernel and is activated on other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38388 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
Early printk was disabled because it caused hangs on some devices, the
old patches were using the CFE console now we use the normal serial
console, it is at a constant address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38309 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
The SRAB interface is used on BCM4707 and BCM5301X SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38198 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
| |
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37958 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37465 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37287 3c298f89-4303-0410-b956-a3cf2f4a3e73
|