aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/bmips/dts
Commit message (Collapse)AuthorAgeFilesLines
* bmips: add support for Arcadyan AR7516Daniel González Cabanelas2023-06-221-0/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi fast ethernet router, 2.4 GHz single band with two internal antennas. It comes with a horizontal stand black shiny casing. Newer Bright Box 1 model stands vertically, and comes with a totally different board inside, not compatible with this firmware. Hardware: - SoC: Broadcom BCM6328 - CPU: single core BMIPS4350 V7.5 @ 320Mhz - RAM: 64 MB DDR2 - Flash: 8 MB SPI NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: Broadcom BCM43227 802.11bgn (onboard) - USB: 1x 2.0 - ADSL: yes, unsupported - Buttons: 2x - LEDs: 9x, power LED is hardware controlled - UART: yes Installation in two steps, new CFE bootloader and firmware: Install new CFE: 1. Power off the router and press the RESET button 2. Power on the router and wait some seconds 3. Release the RESET button 3. Browse to http://192.168.1.1, this web interface will offer both firmware (“Software”) upgrade and bootloader upgrade; be sure to use the bootloader section of the upload form. 4. Upload the new CFE (availabe at the wiki page) 5. Wait about a minute for flashing to finish and reboot into the new bootloader. Install OpenWrt via new CFE web UI: 1. After installing the new CFE, visit http://192.168.1.1 2. Upload the Openwrt cfe firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> (cherry-picked from df8e4b6c2e6440bc9a31467de1739c69c328e391)
* bmips: add support for NuCom R5010UNv2Daniel González Cabanelas2023-06-191-0/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band with two external antennas. Hardware: - SoC: Broadcom BCM6328 - CPU: single core BMIPS4350 V7.5 @ 320Mhz - RAM: 64 MB DDR2 - Flash: 16 MB SPI NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard) - USB: 1x 2.0 - Buttons: 2x - ADSL: yes, unsupported - LEDs: 7x - UART: yes Installation via CFE web UI: 1. Power off the router and press the RESET button 2. Power on the router and wait 12 or more seconds 3. Release the RESET button 4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> (cherry picked from commit 6cb3328b4fd4939f3800d4be9d52744b753de1b6)
* bmips: add support for Comtrend VG-8050Álvaro Fernández Rojas2023-06-161-0/+237
| | | | | | | | | | | | | | | | | | | | | | | | | | | The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with two external antennas. Hardware: - SoC: Broadcom BCM63169 - CPU: dual core BMIPS4350 @ 400Mhz - RAM: 128 MB DDR - Flash: 128 MB NAND - LAN switch: Broadcom BCM53125, 5x 1Gbit - Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn - USB: 1x 2.0 (optional) - Buttons: 2x (reset) - LEDs: yes - UART: yes Installation via CFE web UI: 1. Power off the router. 2. Press reset button near the power switch. 3. Keep it pressed while powering up during ~20+ seconds. 4. Browse to http://192.168.1.1 and upload the firmware. 5. Wait a few minutes for it to finish. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit 47cc09aa7a9a12cb7b18ef96f0b5d0bcb5d84b9e)
* bmips: dts: dgnd3700: fix WAN portÁlvaro Fernández Rojas2023-06-151-1/+1
| | | | | | | | All switch ports are labeled as port@address so let's follow the same pattern. Fixes: ed79519b8d89 ("bmips: add support for Netgear DGND3700 v1, DGND3800B") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit d9210c5ff797896317d1b6293a5ad768b7482cfe)
* bmips: add support for Sercomm AD1018Álvaro Fernández Rojas2023-06-151-0/+312
| | | | | | | | | | | | | | | | | | | | | | | | | The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with two internal antennas. Hardware: - SoC: Broadcom BCM6328 - CPU: single core BMIPS4350 @ 320Mhz - RAM: 64 MB (v1) / 128 MB (v2) DDR - Flash: 128 MB NAND - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn - USB: 1x 2.0 - Buttons: 3x (reset) - LEDs: yes - UART: yes Installation via OEM web UI: 1. Use the admin credentials to login via web UI 2. Go to Managament->Update firmware and select the OpenWrt CFE firmware 3. Press "Update Firmware" button and wait some minutes until it finish Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit 38ebb2eafde604ff6d9b0021d1d21208070a2d09)
* bmips: add support for Actiontec R1000HDaniel González Cabanelas2023-06-151-0/+220
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with two external antennas. It comes with a coaxial HomePNA port. Hardware: - SoC: Broadcom BCM6368 - CPU: dual core BMIPS4350 V3.1 @400Mhz - RAM: 64 MB DDR - Flash: 32 MB parallel NOR - LAN switch: Broadcom BCM53115, 5x 1Gbit - LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn - USB: 1x 2.0 - Buttons: 2x, 1 reset - LEDs: 7x - UART: yes The HPNA hardware probably needs a firmware to make the coaxial port work. In the OEM firmware, it's apparently sent with an utility (inhpna) through the ethernet port. Installation via CFE web UI: 1. Connect the UART serial port. 2. Power on the router and press enter at the console prompt to stop the bootloader. 4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> (cherry picked from commit e1a55de7a7eafd40a4fab5f29153a1a3c3606818)
* bmips: fix NETGEAR DGND3700v2 boot loopÁlvaro Fernández Rojas2023-06-151-0/+1
| | | | | | | | | | | | | The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX is the number of firmware upgrades performed by the bootloader. Other bcm63xx devices rename cferam.000 to cferam.XXX, but this device is special because the cferam name isn't changed on the first firmware flashing but it's changed on the subsequent ones. Therefore, we need to look for "cfe" instead of "cferam" to properly detect the cferam partition and fix the bootlop. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit 915e914cfaa243ea36f8c7a4f0f045ec890304fa)
* bmips: add support for Comtrend AR-5381uÁlvaro Fernández Rojas2023-06-121-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | The Comtrend AR-5381u is a wifi fast ethernet router, 2.4 GHz single band with two internal antennas. Hardware: - SoC: Broadcom BCM6328 - CPU: single core BMIPS4350 @ 320Mhz - RAM: 64 MB DDR - Flash: 16 MB SPI NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: miniPCI Broadcom BCM43225 802.11bgn - USB: 1x 2.0 - Buttons: 1x (reset) - LEDs: yes - UART: yes Installation via CFE web UI: 1. Power off the router. 2. Press reset button near the power switch. 3. Keep it pressed while powering up during ~20+ seconds. 4. Browse to http://192.168.1.1 and upload the firmware. 5. Wait a few minutes for it to finish. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit bcdf861519)
* bmips: add support for Comtrend WAP-5813nÁlvaro Fernández Rojas2023-06-111-0/+230
| | | | | | | | | | | | | | | | | | | | | | | | | | | The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with two external antennas. Hardware: - SoC: Broadcom BCM6369 - CPU: dual core BMIPS4350 @ 400Mhz - RAM: 64 MB DDR - Flash: 8 MB parallel NOR - LAN switch: Broadcom BCM53115, 5x 1Gbit - Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn - USB: 1x 2.0 (optional) - Buttons: 3x (reset) - LEDs: yes - UART: yes Installation via CFE web UI: 1. Power off the router. 2. Press reset button near the power switch. 3. Keep it pressed while powering up during ~20+ seconds. 4. Browse to http://192.168.1.1 and upload the firmware. 5. Wait a few minutes for it to finish. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit c3b1ef2dfd)
* bmips: add support for Comtrend VR-3025unÁlvaro Fernández Rojas2023-06-111-0/+182
| | | | | | | | | | | | | | | | | | | | | | | | | | | The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with two external antennas. Hardware: - SoC: Broadcom BCM6368 - CPU: dual core BMIPS4350 @ 400Mhz - RAM: 64 MB DDR - Flash: 8 MB parallel NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn - USB: 1x 2.0 - Buttons: 1x (reset) - LEDs: yes - UART: yes Installation via CFE web UI: 1. Power off the router. 2. Press reset button near the antenna. 3. Keep it pressed while powering up during ~20+ seconds. 4. Browse to http://192.168.1.1 and upload the firmware. 5. Wait a few minutes for it to finish. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> (cherry picked from commit 3baa45fbd8)
* bmips: dts: improve and align device tree filesÁlvaro Fernández Rojas2023-06-1112-71/+40
| | | | | | | Align all the device tree files and follow the same criteria before more devices are ported from bcm63xx and this goes out of control. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add support for Netgear EVG2000Daniel González Cabanelas2023-06-111-0/+237
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with two internal antennas integrated in the main PCB. Hardware: - SoC: Broadcom BCM6369 - CPU: dual core BMIPS4350 V3.1 @400Mhz - RAM: 64 MB DDR - Flash: 16 MB parallel NOR - LAN switch: Broadcom BCM53115, 5x 1Gbit - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn - USB: 2x 2.0 - Buttons: 2x, 1 reset - LEDs: 10x - FXS: 2x - UART: yes Installation via CFE web UI: 1. Power off the router and make a temporal TX-RX shortcircuit on the serial pins. 2. Power on the router and wait 3 or more seconds 3. Remove the TX-RX shortcircuit 4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bmips: add support for Netgear DGND3700 v1, DGND3800BDaniel González Cabanelas2023-06-103-0/+282
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear DGND3700 v1 and DGND3800B are the same device but with different factory firmwares. It's an xDSL wifi router with a slim black shiny casing and 4 PCB internal antennas connected via UFL to a miniPCI detachable card. Hardware: - SoC: Broadcom BCM6368 - CPU: dual core BMIPS4350 V3.1 @400Mhz - RAM: 128 MB DDR - NOR Flash: 32 MB parallel (CFE and OS) - NAND flash: 128 MB (empty) - Ethernet LAN: 5x 1Gbit - Wifi 2.4 GHz: Broadcom BCM43222 802.11bgn - Wifi 5 GHz: Broadcom BCM43222 802.11abgn - USB: 2x 2.0 - Buttons: 3x, 1 reset - LEDs: 11x - UART: yes Installation via OEM web UI: 1. Open the Netgear administration web interface, by default: http://192.168.0.1 user: admin password: password 2. Look for "upgrade firmware" and proceed 3. Wait some minutes until it finishes Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bmips: add support for Observa VH4032NDaniel González Cabanelas2023-06-101-0/+233
| | | | | | | | | | | | | | | | | | | | | | | | The Observa VH4032N is an xDSL wifi router with a vertical white casing and two internal antennas connected via UFL. Hardware: - SoC: Broadcom BCM6368 - CPU: dual core BMIPS4350 V3.1 @400MHz - RAM: 128 MB DDR - Flash: 32 MB parallel NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn - USB: 3x 2.0 - Buttons: 2x, 1 reset - LEDs: 8x, blue and red - UART: 1x Installation via OEM web UI: 1. Use the admin credentials to login via web UI 2. Go to Managament->Update firmware and select the OpenWrt CFE firmware 3. Press "Update Firmware" button and wait some minutes until it finish Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* bmips: document GPIO external interruptsÁlvaro Fernández Rojas2023-04-276-0/+6
| | | | | | | BCM63xx SoCs have an external interrupt controller which can be used for specific GPIO keys. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: increment polled keys interval to 100Álvaro Fernández Rojas2023-04-279-9/+9
| | | | | | | There's no need to poll the gpio keys every 20 ms and the linux kernel documentation suggests 100 ms. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: shg2500: add BCM4360 fallback SPROMÁlvaro Fernández Rojas2023-04-231-0/+13
| | | | | | | | Apart from the embedded BCM63268 wireless, this device has an external BCM4360 connected by PCIe which needs a fallback SPROM. b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: switch to generic bcma/ssb fallback SPROMÁlvaro Fernández Rojas2023-04-233-3/+6
| | | | | | | | Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback SPROMs. This way we don't need to include the b43-sprom fixups on devices without Broadcom wireless. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: pci-bcm6348: load IO resource from DT rangesÁlvaro Fernández Rojas2023-04-182-10/+6
| | | | | | Correctly load IO resource from DT ranges and remove the specific IO resource. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: hg556a: switch to kmod-owl-loaderÁlvaro Fernández Rojas2023-04-181-13/+31
| | | | | | Stop using custom ath9k fixup and switch to standard kmod-owl-loader Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dts: add missing phy modesÁlvaro Fernández Rojas2023-04-105-0/+17
| | | | | | PHY modes should be defined in the device tree for the bcm63xx internal switch. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add support for Sercomm SHG2500Álvaro Fernández Rojas2023-04-091-0/+312
| | | | | | | | Sercomm SHG2500 is a BCM63168 with 128M of RAM, 256M of NAND, an external BCM53124S switch for the LAN ports and internal/external Broadcom wifi. LEDs are connected to an external MSP430G2513 MCU controlled via SPI. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: bcm6362/bcm63268: enable HW RNGÁlvaro Fernández Rojas2023-03-312-0/+24
| | | | | | | This enables the HW Random Number Generator on the BCM6362 and BCM63268 SoCs, which is the same one used on BCM6368 SoC. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: bcm6348-enet: add PHY supportÁlvaro Fernández Rojas2023-03-291-0/+7
| | | | | | | We should ensure that the PHY is properly configured. This is specially needed in devices using the internal PHY for ethernet0. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add basic BCM6358 ethernet supportÁlvaro Fernández Rojas2023-03-282-0/+90
| | | | | | | | The MDIO bus is supported but there are errors when trying to probe and configure the external BCM5325E switch through B53 DSA. Therefore, let's add basic ethernet (but working) support for now. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: add more dsa b53 pending patchesÁlvaro Fernández Rojas2023-03-241-1/+1
| | | | | | | | | | | | | | | | | These patches have now received a positive review upstream, so let's add them to pending patches. 776-net-dsa-b53-mmap-add-phy-ops.patch: This is mostly bmips/bcm63xx-specific to get external switches working without hanging the device when accessing certain registers. 777-net-dsa-b53-mdio-add-support-for-BCM53134: This adds support for BCM53134 switch on DSA B53, so any target using DSA B53 can benefit from it. Also fix sercomm-h500-s external switch IMP port phy-mode. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add support for Sercomm H-500sÁlvaro Fernández Rojas2023-03-223-0/+314
| | | | | | | | | | | | | Sercomm H-500s is a BCM63268 with 128M, internal and external (Quantenna) wifi and external BCM53134S switch. This device is already supported in bcm63xx target, so more information can be found in https://openwrt.org/toh/sercomm/h500-s. It's a perfect example of a device with internal and external switch coexistance since most devices only have ports on one of the switches but not both of them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: drop unneded cpu labels from external switchesÁlvaro Fernández Rojas2023-03-222-2/+0
| | | | | | | | | These labels aren't needed and were accidentally added when adding external switches support for bmips. Fixes: 80a3ecc89489 ("bmips: add Huawei HG253s v2 support") Fixes: 61f3c3b1eebd ("bmips: dgnd3700v2: enable external BCM53125 switch") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dts: nand: add missing address/size cellsÁlvaro Fernández Rojas2023-03-212-0/+6
| | | | | | | | | | | Fixes the following warnings for Netgear DGND3700v2 and Comtrend VR-3032u: [ 1.059540] 7 fixed-partitions partitions found on MTD device brcmnand.0 [ 1.066570] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions [ 1.073766] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions [ 1.081927] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions [ 1.089128] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add Huawei HG253s v2 supportÁlvaro Fernández Rojas2023-03-211-0/+241
| | | | | | | | | | | | | Huawei HG253s v2 is a BCM6362 with 128M RAM, internal wifi and external BCM53124S switch. This device is already supported in bcm63xx target, so more information can be found in https://openwrt.org/toh/huawei/hg253s_v2. It's a perfect example of a device with internal and external switch coexistance since most devices only have ports on one of the switches but not both of them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700v2: enable external BCM53125 switchÁlvaro Fernández Rojas2023-03-211-1/+55
| | | | | | | The Netgear DGND3700v2 has an external BCM53125 switch which can now be enabled as a DSA disjoint switch tree setup. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dts: fix switch compatible stringsÁlvaro Fernández Rojas2023-03-204-4/+4
| | | | | | Use the proper string for each SoC. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dts: fix warningsÁlvaro Fernández Rojas2023-03-097-2/+22
| | | | | | | | - Add missing interrupt-parent to ext_intc. - Add missing #address-cells and #size-cells to gpio_cntl. - Use proper gpio handle for gpios (ar-5315u). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* Revert "bmips: add missing switch cpu label"Álvaro Fernández Rojas2023-03-055-5/+0
| | | | | | | | This reverts commit dc0de05e10a9c6e1ef66ca2934e8a0ff0d488943. As pointed out by @BKPepe and @arinc9 this was removed by 9df035b since it isn't needed. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add missing switch cpu labelÁlvaro Fernández Rojas2023-03-045-0/+5
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* treewide: remove label = "cpu" from DSA dt-bindingArınç ÜNAL2023-02-265-5/+0
| | | | | | | This is not used by the DSA dt-binding, so remove it from all devicetrees. Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* bmips: convert mtd-mac-address to nvmem implementationAnsuel Smith2021-07-196-13/+82
| | | | | | | Define nvmem-cells and convert mtd-mac-address to nvmem implementation. The conversion is done with an automated script. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* bmips: dts: align LEDsÁlvaro Fernández Rojas2021-03-296-32/+45
| | | | | | Align all bmips devices LED configurations. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: backport accepted pinctrl patchesÁlvaro Fernández Rojas2021-03-2911-248/+245
| | | | | | | These patches have been accepted for linux v5.13. External interrupts not supported for now. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: vr-3032u: fix gpio keysÁlvaro Fernández Rojas2021-03-291-2/+2
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700-v2: fix gpio keysÁlvaro Fernández Rojas2021-03-291-9/+9
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: switch to upstream ehci overcurrent flagÁlvaro Fernández Rojas2021-03-246-6/+6
| | | | | | | After backporting upstream ehci overcurrent patches we need to use spurious-oc instead of ignore-oc. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add ATH9K PCI fixupsÁlvaro Fernández Rojas2021-03-231-0/+15
| | | | | | | Add support for registering ATH9K PCI fixups needed to bring up wifi on some devices. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add B43 SPROM PCI fixupsÁlvaro Fernández Rojas2021-03-233-1/+75
| | | | | | Add support for registering fallback BCMA/SSB B43 SPROMs. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add experimental PCI/PCIe supportÁlvaro Fernández Rojas2021-03-2311-0/+223
| | | | | | | | These PCI drivers are a bit hacky and definitely not suitable for upstreaming, but hopefully we can use them as a base for developing proper upstream PCI drivers. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700-v2: fix ethernetÁlvaro Fernández Rojas2021-03-161-0/+16
| | | | | | | This is a temporary workaround to get the ethernet working, since external switch is connected by MDIO and it needs additional work. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add experimental ethernet supportÁlvaro Fernández Rojas2021-03-1410-0/+637
| | | | | | | | | | | | | | | | | | This adds experimental ethernet support for BCM6318, BCM6328, BCM6362, BCM6368 and BCM63268. BCM6358 needs a different driver, so there's no support for now. Working devices: - Comtrend AR-5315u - Comtrend AR-5387un - Comtrend VR-3025u - Comtrend VR-3032u Not working devices: - Netgear DGND3700 v2 (no idea on how the external switch is connected) - Huawei HG556a ver B (BCM6358 needs a separate driveer) Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: automatically detect RAM sizeÁlvaro Fernández Rojas2021-03-086-30/+0
| | | | | | | | | Introduce new patch for automatically detecting RAM size. Some boards have a different amount of RAM depending on the HW revision. Therefore, automatically detecting the RAM size instead of hard-coding it will reduce the number of device definitions. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dts: comestic changesÁlvaro Fernández Rojas2021-03-088-22/+18
| | | | | | Improve and refactor device tree files. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: remove unneeded console from bootargsÁlvaro Fernández Rojas2021-03-086-6/+6
| | | | | | console parameter is no longer needed after latest procd update. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 04:48:01 +0000