openwrt/upstream - upstream openwrt

	Commit message (Collapse)	Author	Age	Files	Lines
*	bcm63xx: stop using legacy lzma for all devices	Álvaro Fernández Rojas	2020-06-03	1	-54/+59
\| \| \| \| \| \| \| \| \|	BCM6368 and newer devices are compatible with any lzma compression parameters. Add a new legacy device definition and use it on BCM6358 and older devices. Compressed kernel size is reduced by ~1.35%. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
*	brcm63xx: add support for ADB P.DG A4001N A-000-1A1-AX	Daniele Castro	2020-05-22	1	-0/+12
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI) has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE. It has different LEDs configuration and flash size/layout w.r.t the ADB P.DG A4001N A-000-1A1-AX. Hardware: * Board ID: 96328avng * SoC: Broadcom BCM6328 * RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01) * LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193) NC GND NC Installation via CFE: * Stock CFE has to be overwriten with one for 96328avng boards that can upload .bin images with no signature check (cfe-A4001N-V0000_96328avng.bin) * connect a serial port to the board * Stop the boot process after power on by pressing enter * set static IP 192.168.1.2 and subnet mask 255.255.255.0 * navigate to http://192.168.1.1/ * upload the OpenWrt image file Signed-off-by: Daniele Castro <danielecastro@hotmail.it> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
*	bcm63xx: image: add CVG834G CHIP_ID	Álvaro Fernández Rojas	2020-05-20	1	-1/+1
\| \| \| \|	Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
*	bcm63xx: image: rename CFE_CHIP_ID to CHIP_ID	Álvaro Fernández Rojas	2020-05-20	1	-91/+90
\| \| \| \| \| \|	Rename CFE_CHIP_ID to a generic name that doesn't involve CFE. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
*	bcm63xx: loader-lzma: use default lzma	Álvaro Fernández Rojas	2020-05-12	1	-1/+1
\| \| \| \| \| \|	Specific CFE LZMA parameters aren't needed for LZMA Loader. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
*	bcm63xx: disable all devices with <= 4MiB flash and <= 32 MiB RAM	Jonas Gorski	2020-04-12	1	-0/+11
\| \| \| \| \| \| \| \| \| \| \|	Device with 4 MiB flash and 32 MiB RAM won't be able to run OpenWrt in a sufficient manner without tweaks, so don't build images for them by default. This includes all BCM6338, BCM6345 and BCM6348 "generic" devices, as there are no supported devices of these with more than that. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
*	treewide: gather DEVICE_VARS into one place	Sungbo Eo	2020-03-21	1	-5/+6
\| \| \| \| \| \| \| \| \| \| \|	Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
*	brcm63xx: rename target to bcm63xx	Adrian Schmutzler	2020-02-14	1	-0/+1151
	This change makes the names of Broadcom targets consistent by using the common notation based on SoC/CPU ID (which is used internally anyway), bcmXXXX instead of brcmXXXX. This is even used for target TITLE in make menuconfig already, only the short target name used brcm so far. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>