aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/bcm63xx/base-files/etc/board.d/01_leds
Commit message (Collapse)AuthorAgeFilesLines
* bcm63xx: add support for ADB P.DG A4101N A-000-1A1-AEDaniele Castro2020-12-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4101N A-000-1A1-AE has a similar PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. Hardware: * Board ID: 96328avngv * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25 * Serial flash: 16 Mbyte - Winbond 25Q128BVFG * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43225 Wireless Network Adapter (rev 23) * LEDs: 1x Power, 1x DSL, 1x Internet, 4x ETH, 1x USB, 1x WLAN, 1x WPS, 1x TEL * Buttons: 1x Reset, 1x WPS, 1x unnamed * UART: 1x TTL 115200n8, VCC RX TX GND, on J502 connector Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the cfe boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file A4101N GPIO LAYOUT: Power always on DSL GPIO483(03) Internet GPIO491(11) ETH1 GPIO505(25) ETH2 GPIO506(26) ETH3 GPIO507(27) ETH4 GPIO508(28) USB GPIO490(10) WLAN controlled by BCM43225 WPS GPIO489(09) TEL GPIO511(31) Key RESET GPIO503(23) Key WPS GPIO504(24) Key unnamed GPIO492(12) Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [Amend commit description, DTS improvements, refresh patches] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: Add support for D-Link DSL-2750u rev C1Ahmed Naseef2020-12-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the D-Link DSL-2750u rev C1. (https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1) It uses the same hardware as ADB P.DG A4001N. CPU: Broadcom BCM63281 (320 MHz) RAM: 32M (Winbond W9725G6JB) Flash: 8M (MXIC MX25L6445E) Ethernet: 4x 100 Mbps Wireless: 802.11b/g/n: BCM43225 USB: 1x 2.0 Flash instructions: 1. Assign static IP 192.168.1.100 to PC 2. Unplug the power source 3. Press the RESET button at the router, don't release it yet! 4. Plug the power source.Wait some seconds 5. Release the RESET button 6. Browse to http://192.168.1.1 7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and wait some minutes until the firmware upgrade finish. Signed-off-by: Ahmed Naseef <naseefkm@gmail.com> [DTS improvements, proper board patch, refresh patches] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: add USB status LED in 01_leds for ADP P.DG A4001NDaniele Castro2020-12-041-1/+2
| | | | | | Add a status LED in 01_leds for USB 2-1 connected devices. Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
* bcm63xx: remove model name from LED labelsAdrian Schmutzler2020-10-101-61/+48
| | | | | | | | | | | | | | | | Like in the previous patches for various targets, this will remove the "devicename" from LED labels in bcm63xx, as it's useless and only creates complexity. The devicename is removed in DTS files and 01_leds, merging several cases on the way. A migration script is added for existing configurations. Note that a few labels were using "model::function" scheme without color specified, those were converting to just "function" and the necessary migrations were added to the migration script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: add support for the Sercomm H500-sDaniel González Cabanelas2020-06-071-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sercomm H500-s is an xDSL dual band wireless router based on Broadcom BCM63167 SoC. Hardware: SoC: Broadcom BCM63167 CPU: BMIPS4350 V8.0, 400 MHz, 2 cores Flash: NAND 128 MiB RAM: DDR3 128 MiB Ethernet: 4x 10/100/1000 Mbps Switch: BCM53134S Wireless: 802.11b/g/n: BCM435f (integrated) 802.11ac: Quantenna QT3740BC (onboard SoC) USB: 1x 2.0 LEDs/Buttons: 11x / 2x Flash instruction, web UI: 1. Reset to defaults using the reset button if the admin password is unknown 2. Login into the web UI as admin. Address: http://192.168.0.1 User: admin Password: VF-ESVodafone-H-500-s or l033i-h500s 3. Go to Settings -> Firmware Update, and select the Openwrt factory firmware 4. Update the firmware. 5. Wait until it finish, the device will reboot with Openwrt installed on the alternative image partitions keeping the stock firmware in the former. Notes: - The patch also adds support for the lowi version. Only the factory firmware is different. - The integrated Wifi in the Broadcom Soc isn't still supported. - The Quantenna 802.11ac wifi works ok, but needs to be configured with the Quantenna client application. It can't be configured with Luci nor any iw command since it's a separated subsystem linked via ethernet. - The BCM53134S external switch is managed via MDIO which isn't supported in this target. Therefore it will behave as a dumb switch. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* brcm63xx: add support for ADB P.DG A4001N A-000-1A1-AXDaniele Castro2020-05-221-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI) has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE. It has different LEDs configuration and flash size/layout w.r.t the ADB P.DG A4001N A-000-1A1-AX. Hardware: * Board ID: 96328avng * SoC: Broadcom BCM6328 * RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01) * LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193) NC GND NC Installation via CFE: * Stock CFE has to be overwriten with one for 96328avng boards that can upload .bin images with no signature check (cfe-A4001N-V0000_96328avng.bin) * connect a serial port to the board * Stop the boot process after power on by pressing enter * set static IP 192.168.1.2 and subnet mask 255.255.255.0 * navigate to http://192.168.1.1/ * upload the OpenWrt image file Signed-off-by: Daniele Castro <danielecastro@hotmail.it> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: use model part of board name as variable in 01_ledsAdrian Schmutzler2020-05-221-10/+11
| | | | | | | | This extracts the model part of the board name and uses it for the LED string identifiers in 01_leds. As this makes statements more generic, it will allow to merge more cases in the future. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: WIP: add Huawei HG253s v2 supportÁlvaro Fernández Rojas2020-05-211-0/+3
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: fix AD1018 WLAN ledÁlvaro Fernández Rojas2020-05-201-1/+3
| | | | | | | Standard AD1018 has lower case LEDs. Fixes: 5f826919232d ("bcm63xx: add unmodded SERCOMM AD1018 support") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add unmodded SERCOMM AD1018 supportÁlvaro Fernández Rojas2020-05-191-0/+1
| | | | | | | | | Until now only HW modded SPI flash version was supported. BCM6328 with 64M RAM and 128M NAND. More info: https://openwrt.org/toh/sercomm/ad1018 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add NETGEAR DGND3700v2 supportÁlvaro Fernández Rojas2020-05-191-0/+5
| | | | | | | | BCM6362 with 64M RAM, 32M NAND and BCM53125 switch. Switch is connected by MMAP, which is currently unsupported (no VLANs). More info: https://openwrt.org/toh/netgear/dgnd3700v2 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add support for Comtrend VR-3032uÁlvaro Fernández Rojas2020-05-181-0/+3
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* brcm63xx: rename target to bcm63xxAdrian Schmutzler2020-02-141-0/+89
This change makes the names of Broadcom targets consistent by using the common notation based on SoC/CPU ID (which is used internally anyway), bcmXXXX instead of brcmXXXX. This is even used for target TITLE in make menuconfig already, only the short target name used brcm so far. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 08:35:50 +0000