| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
| |
There's no eth0.2 since all ethernet ports as configured as LAN.
LAN LED is unneeded since all ethernet ports have their own LED.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Technicolor TG582n has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.
Hardware:
* Board ID: DANT-1
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L6445EMI
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x Ethernet, 1x Broadband, 2x Wi-Fi, 2x WPS, 4x ethernet
* Buttons: 1x Reset, 1x WPS, 1x WiFi
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
PCB: |GPIO: |TG582n:
LED2R |488(08) |red Power
LED2G |484(04) |green Power
LED10R |486(06) |
LED13G |485(05) |green Ethernet
LED11R |494(14) |
LED14G |491(11) |green Broadband
LED5R |487(07) |red Internet
LED5G |481(01) |green Internet
LED12R |498(18) |
LED12G |499(19) |
LED6R |482(02) |red Wi-Fi
LED6G |483(03) |green Wi-Fi
LED7R |490(10) |red WPS
LED7G |489(09) |green WPS
LED4 |508(28) |ethernet port 4
LED3 |507(27) |ethernet port 3
LED9 |506(26) |ethernet port 2
LED8 |505(25) |ethernet port 1
SW3 |503(23) |key Reset
SW5 |504(24) |key WPS
SW4 |495(15) |key Wi-Fi
SW6 |493(13) |
SW1 |492(12) |
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Fix base-files, refresh patch]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.
Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
PCB: |GPIO: |TG582n: |AGTWI:
LED2R |488(08) |red Power |red Power
LED2G |484(04) |green Power |green Power
LED10R |486(06) | |missing R85 end LED
LED13G |485(05) |green Ethernet |green ADSL
LED11R |494(14) | |red Internet
LED14G |491(11) |green Broadband |green Internet
LED5R |487(07) |red Internet |red Wi-Fi
LED5G |481(01) |green Internet |green Wi-Fi
LED12R |498(18) | |red Service
LED12G |499(19) | |green Service
LED6R |482(02) |red Wi-Fi |missing R108 end LED
LED6G |483(03) |green Wi-Fi |missing R107 end LED
LED7R |490(10) |red WPS |missing R91 end LED
LED7G |489(09) |green WPS |missing R92 end LED
LED4 |508(28) |ethernet port 4 |ethernet port 4
LED3 |507(27) |ethernet port 3 |ethernet port 3
LED9 |506(26) |ethernet port 2 |ethernet port 2
LED8 |505(25) |ethernet port 1 |ethernet port 1
SW3 |503(23) |key Reset |key Reset
SW5 |504(24) |key WPS |key Wi-Fi/LED
SW4 |495(15) |key Wi-Fi |missing R127 end key
SW6 |493(13) | |missing R171 end key
SW1 |492(12) | |missing R1 end key
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ADB P.DG A4101N A-000-1A1-AE has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.
Hardware:
* Board ID: 96328avngv
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - Winbond 25Q128BVFG
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43225 Wireless Network Adapter (rev 23)
* LEDs: 1x Power, 1x DSL, 1x Internet, 4x ETH, 1x USB, 1x WLAN, 1x WPS, 1x TEL
* Buttons: 1x Reset, 1x WPS, 1x unnamed
* UART: 1x TTL 115200n8, VCC RX TX GND, on J502 connector
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the cfe boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
A4101N GPIO LAYOUT:
Power always on
DSL GPIO483(03)
Internet GPIO491(11)
ETH1 GPIO505(25)
ETH2 GPIO506(26)
ETH3 GPIO507(27)
ETH4 GPIO508(28)
USB GPIO490(10)
WLAN controlled by BCM43225
WPS GPIO489(09)
TEL GPIO511(31)
Key RESET GPIO503(23)
Key WPS GPIO504(24)
Key unnamed GPIO492(12)
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Amend commit description, DTS improvements, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the D-Link DSL-2750u rev C1.
(https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1)
It uses the same hardware as ADB P.DG A4001N.
CPU: Broadcom BCM63281 (320 MHz)
RAM: 32M (Winbond W9725G6JB)
Flash: 8M (MXIC MX25L6445E)
Ethernet: 4x 100 Mbps
Wireless: 802.11b/g/n: BCM43225
USB: 1x 2.0
Flash instructions:
1. Assign static IP 192.168.1.100 to PC
2. Unplug the power source
3. Press the RESET button at the router, don't release it yet!
4. Plug the power source.Wait some seconds
5. Release the RESET button
6. Browse to http://192.168.1.1
7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and
wait some minutes until the firmware upgrade finish.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
[DTS improvements, proper board patch, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
| |
Add a status LED in 01_leds for USB 2-1 connected devices.
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Like in the previous patches for various targets, this will remove
the "devicename" from LED labels in bcm63xx, as it's useless and
only creates complexity.
The devicename is removed in DTS files and 01_leds, merging
several cases on the way. A migration script is added for
existing configurations.
Note that a few labels were using "model::function" scheme without
color specified, those were converting to just "function" and the
necessary migrations were added to the migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sercomm H500-s is an xDSL dual band wireless router based on Broadcom
BCM63167 SoC.
Hardware:
SoC: Broadcom BCM63167
CPU: BMIPS4350 V8.0, 400 MHz, 2 cores
Flash: NAND 128 MiB
RAM: DDR3 128 MiB
Ethernet: 4x 10/100/1000 Mbps
Switch: BCM53134S
Wireless: 802.11b/g/n: BCM435f (integrated)
802.11ac: Quantenna QT3740BC (onboard SoC)
USB: 1x 2.0
LEDs/Buttons: 11x / 2x
Flash instruction, web UI:
1. Reset to defaults using the reset button if the admin password is
unknown
2. Login into the web UI as admin.
Address: http://192.168.0.1
User: admin
Password: VF-ESVodafone-H-500-s or l033i-h500s
3. Go to Settings -> Firmware Update, and select the Openwrt factory
firmware
4. Update the firmware.
5. Wait until it finish, the device will reboot with Openwrt installed
on the alternative image partitions keeping the stock firmware in
the former.
Notes:
- The patch also adds support for the lowi version. Only the factory
firmware is different.
- The integrated Wifi in the Broadcom Soc isn't still supported.
- The Quantenna 802.11ac wifi works ok, but needs to be configured with
the Quantenna client application. It can't be configured with Luci
nor any iw command since it's a separated subsystem linked via
ethernet.
- The BCM53134S external switch is managed via MDIO which isn't
supported in this target. Therefore it will behave as a dumb switch.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected
to different GPIO PINs in active low configuration.
OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE.
It has different LEDs configuration and flash size/layout
w.r.t the ADB P.DG A4001N A-000-1A1-AX.
Hardware:
* Board ID: 96328avng
* SoC: Broadcom BCM6328
* RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01)
* LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193)
NC GND NC
Installation via CFE:
* Stock CFE has to be overwriten with one for 96328avng boards that can upload
.bin images with no signature check (cfe-A4001N-V0000_96328avng.bin)
* connect a serial port to the board
* Stop the boot process after power on by pressing enter
* set static IP 192.168.1.2 and subnet mask 255.255.255.0
* navigate to http://192.168.1.1/
* upload the OpenWrt image file
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
| |
This extracts the model part of the board name and uses it for the
LED string identifiers in 01_leds. As this makes statements more
generic, it will allow to merge more cases in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
| |
Standard AD1018 has lower case LEDs.
Fixes: 5f826919232d ("bcm63xx: add unmodded SERCOMM AD1018 support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
| |
Until now only HW modded SPI flash version was supported.
BCM6328 with 64M RAM and 128M NAND.
More info: https://openwrt.org/toh/sercomm/ad1018
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
| |
BCM6362 with 64M RAM, 32M NAND and BCM53125 switch.
Switch is connected by MMAP, which is currently unsupported (no VLANs).
More info: https://openwrt.org/toh/netgear/dgnd3700v2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|