aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/bcm53xx
Commit message (Collapse)AuthorAgeFilesLines
...
* bcm53xx: MR32: replace i2c-gpio with SoC's i2cChristian Lamparter2021-10-303-1/+118
| | | | | | | | | During review of the MR32, Florian Fainelli pointed out that the SoC has a real I2C-controller. Furthermore, the connected pins (SDA and SCL) would line up perfectly for use. This patch swaps out the the bitbanged i2c-gpio with the real deal. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: backport patch fixing pinctrl driverRafał Miłecki2021-10-292-33/+106
| | | | | | | This switches pinctrl driver to use the old & good DT binding. There is no more need to adjust upstream DTS file. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: bridge all LAN ports on Linksys EA9500Rafał Miłecki2021-10-221-1/+1
| | | | | | External switch ports need to be bridged too. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: switch to the upstream DSA-based b53 driverRafał Miłecki2021-10-215-77/+49
| | | | | | | | | | 1. Drop swconfig 2. Simplify network setup 3. Verify network config 4. Disable Buffalo WZR-900DHP for now - it misses ports definition Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-By: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: enable Linksys EA6300 & EA9200 buildsRafał Miłecki2021-10-181-3/+0
| | | | | | | | | | Both should be supported since: 1. Adding NVMEM driver for NVRAM 2. Using NVRAM info for determining active firmware partition Linksys EA9500 uses very similar design and works fine. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport bgmac upstream commits from 5.15 / for 5.16Rafał Miłecki2021-10-071-41/+0
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.4 to 5.4.150Hauke Mehrtens2021-10-021-2/+2
| | | | | | | | | | | | | | | | Manually rebased: generic/pending-5.4/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch mvebu/patches-5.4/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch Removed upstreamed: layerscape/patches-5.4/819-uart-0004-MLK-18137-fsl_lpuart-Fix-loopback-mode.patch All others updated automatically. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.10 to 5.10.70Rui Salvaterra2021-09-301-41/+0
| | | | | | | Deleted (upstreamed): bcm53xx/patches-5.10/181-Revert-USB-bcma-Add-a-check-for-devm_gpiod_get.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.69Rui Salvaterra2021-09-301-6/+1
| | | | | | Patches automatically refreshed. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.65Rui Salvaterra2021-09-301-2/+2
| | | | | | | | | Manually refreshed: generic/pending-5.10/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm53xx: MR32: read mac-address from eepromChristian Lamparter2021-09-232-4/+46
| | | | | | | | Meraki wrote the ethernet MAC-address of the device onto the eeprom (AT24C64) at the fixed location 0x66 to 0x6C. Let's fetch it from there. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* scripts: mkits.sh: Allow legacy @ mode for dts creationDamien Mascord2021-09-231-3/+5
| | | | | | | | | | | | | | | | | | commit 5ec60cbe9d94 ("scripts: mkits.sh: replace @ with - in nodes") broke support for Meraki MR32 and this patch makes the replacement configurable allowing for specifying the @ or - or whatever character that is desired to retain backwards compatibility with existing devices. For example, this patch includes the fix for the Meraki MR32 in target/linux/bcm53xx/image for meraki_mr32: DEVICE_DTS_DELIMITER := @ DEVICE_DTS_CONFIG := config@1 Fixes: 5ec60cbe9d94 ("scripts: mkits.sh: replace @ with - in nodes") Signed-off-by: Damien Mascord <tusker@tusker.org> [Added tags, checkpatch.pl fixes, noted that this is for old stuff] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: backport early DT patches queued for 5.16Rafał Miłecki2021-09-2312-4/+642
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: drop DTS based workaround for serial support in procdRafał Miłecki2021-09-161-116/+0
| | | | | | | | | Specifying serial in bootargs is not needed since the commit ffeb37047e85 ("procd: update to git HEAD"). It's thanks to the procd commit 2cfc26f8456a ("inittab: detect active console from kernel if no console= specified"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.4 to 5.4.145John Audia2021-09-131-1/+1
| | | | | | | | | | | | Removed upstreamed: generic-backport/040-ARM-8918-2-only-build-return_address-if-needed.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.64John Audia2021-09-131-1/+1
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* bcm53xx: specify switch ports for more devicesRafał Miłecki2021-09-072-0/+864
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: switch to the kernel 5.10Rafał Miłecki2021-08-311-1/+1
| | | | | | With PCI and USB regressions fixed it should be safe to switch now. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix kmod-i2c-bcm-iproc for kernel 5.10Rafał Miłecki2021-08-311-1/+3
| | | | | | | | | | | | | | | | | | | | | I2C_BCM_IPROC selects I2C_SLAVE which in turn makes two new symbols available: I2C_SLAVE_EEPROM and I2C_SLAVE_TESTUNIT. That was causing: I2C support (I2C) [M/n/y/?] m Enable compatibility bits for old user-space (I2C_COMPAT) [N/y/?] n I2C device interface (I2C_CHARDEV) [M/n/?] m I2C bus multiplexing support (I2C_MUX) [N/m/?] n Autoselect pertinent helper modules (I2C_HELPER_AUTO) [N/y/?] n SMBus-specific protocols (I2C_SMBUS) [N/m/?] n I2C/SMBus Test Stub (I2C_STUB) [N/m/?] n I2C slave support (I2C_SLAVE) [Y/?] y I2C eeprom slave driver (I2C_SLAVE_EEPROM) [N/m/?] n I2C eeprom testunit driver (I2C_SLAVE_TESTUNIT) [N/m/?] (NEW) Ideally I2C_SLAVE should probably be packaged as kmod-i2c-slabe. For now just modify kmod-i2c-bcm-iproc to fix kernel compilation. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix USB in kernel 5.10Rafał Miłecki2021-08-311-0/+41
| | | | | | | This makes USB controller driver work with USBs that are always powered on (don't require toggling any GPIO). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport missed DT patch cleaning up CRU blockRafał Miłecki2021-08-3014-22/+196
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport the latest upstream DT changesRafał Miłecki2021-08-2925-2/+2324
| | | | | | | | This includes: 1. BCM5301X changes from 5.14 and queued 5.15 stuff 2. NSP changes from 5.11 - 5.15 for kernel 5.10 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: move two symbols to the generic kconfigsRui Salvaterra2021-08-292-4/+0
| | | | | | | CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them to the generic kconfigs. And resort the generic kconfigs while at it. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.55Rui Salvaterra2021-08-084-5/+5
| | | | | | No deleted or manually refreshed patches. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.4 to 5.4.136John Audia2021-07-311-1/+1
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* bcm53xx: refresh kernel 5.10 configRafał Miłecki2021-07-291-76/+12
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: add testing support for kernel 5.10Rafał Miłecki2021-07-2932-1/+2357
| | | | | | | | | | | | | | | | It still requires fixing PCIe support: [ 6.644699] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges: [ 6.652217] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff] [ 6.661833] OF: /axi@18000000/pcie@12000: Missing device_type [ 6.667622] pcie_iproc_bcma: probe of bcma0:7 failed with error -12 [ 6.673985] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges: [ 6.681514] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff] [ 6.691137] pcie_iproc_bcma: probe of bcma0:8 failed with error -12 [ 6.697522] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges: [ 6.705048] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff] [ 6.714669] pcie_iproc_bcma: probe of bcma0:9 failed with error -12 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.4 to 5.4.118John Audia2021-05-231-2/+2
| | | | | | | | | | | | | | | | | | Manually rebased: ath79/patches-5.4/0033-spi-ath79-drop-pdata-support.patch Removed uneeded patch: ath79/patches-5.4/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-211-2/+0
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove redundant ubifs kconfig symbolsRui Salvaterra2021-04-211-4/+0
| | | | | | | For the targets which enable ubifs, these symbols are already part of the generic kconfigs. Drop them from the target kconfigs. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm53xx: fix Luxul XWR-3150 LAN ports numberingRafał Miłecki2021-04-211-1/+1
| | | | | | | Port numbers were reverted. Fixes: c459a6bf482f ("bcm53xx: add support for Luxul FullMAC WiFi devices") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: add pending TRX patch for "firmware" partitionRafał Miłecki2021-04-141-0/+43
| | | | | | | This fixes partitioning on Linksys EA9500. With this change only the currently used firmware MTD partition gets parsed. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: enhance support for Linksys EA9500Vivek Unune2021-04-014-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add leds and configs 2. Add network configs 3. Add script to clear partial boot flag 4. Hack to use port 5 as cpu port as port 8 connected to eth2 wont pass any frames 5. Enable EA9500 image generation Hardware Info: - Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz - Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 - DDR3 RAM - 256 MB - Flash - 128 MB (Toshiba TC58BVG0S3HTA00) - 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) - 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch - Ports - 8 Ports, 1 WAN Ports - Antennas - 8 Antennas - Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1 Flashing Instructions: 1. Connect a USB-TTL table to J6 on the router as well as a ethernet cable to a lan port and your PC. 2. Power-on the router. 3. Use putty or a serial port program to view the terminal. Hit Ctrl+C and interrupt the CFE terminal terminal. 4. Setup a TFTP server on your local machine at setup you local IP to 192.168.1.2 5. Start the TFTP Server 6. Run following commands at the CFE terminal flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2 nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit 7. Reboot router to be presented by OpenWrt Note: Only installation method via serial cable is supported at the moment. The trx firmware has to be flashed to both the partitions using following commands from CFE prompt. This will cover US and Non-US variants. Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use upstream Linksys EA9500 fixesRafał Miłecki2021-04-012-1/+30
| | | | | | One fix was accepted, one was added. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix Linksys EA9500 partitionsRafał Miłecki2021-03-291-0/+58
| | | | | | Use proper DT binding. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport 5.13 mtd partitioning changesRafał Miłecki2021-03-291-0/+1
| | | | | | | | 1. Use upstream accepted NVMEM patches 2. Minor fix for BCM4908 partitioning 3. Support for Linksys firmware partitions on Northstar Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.4 to 5.4.106John Audia2021-03-211-1/+1
| | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [remove accidental whitespace edit] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: backport first 5.13 DTS changesRafał Miłecki2021-03-143-1/+476
| | | | | | | This adds NVMEM bindings that are needed for proper booting on Linksys devices. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: initialize NVRAM from NVMEM driverRafał Miłecki2021-03-122-0/+92
| | | | | | | | | | | NVRAM access may be needed early in boot process. Reading it using mtd happens quite late in the init process. Add NVRAM initialization to the NVMEM driver which comes up early and depends on IO mapping only. This is required by Linksys devices which use NVRAM content for proper partitioning (detecting current firmware partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport NVMEM NVRAM driverRafał Miłecki2021-03-103-0/+181
| | | | | | | It supports NVRAM access described using DT binding. Right now NVRAM data is exposed using /sys/bus/nvmem/ only. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Revert "bcm53xx: add support for reading NVRAM based on DT mapping"Rafał Miłecki2021-03-102-141/+0
| | | | | | | This reverts commit b0376462c164344d6be9fe1568a9f13ffd8fbb16. Those changes were rejected and were replaced with an NVMEM driver. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-062-2/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: add support for reading NVRAM based on DT mappingRafał Miłecki2021-03-022-0/+141
| | | | | | | This is required for devices that use NVRAM data for detecting currently used firmware partition (e.g. Linksys devices). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport more upstream dts stuff from kernel 5.11Rafał Miłecki2021-02-257-0/+507
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport Linksys Panamera (EA9500) patchesVivek Unune2021-02-255-2/+230
| | | | | | | | | | | | | | | | These patches have been already accepted. 302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch had to be updated. [rmilecki: use actual upstream accepted patches replace v5.10 with v5.11 to match actual upstream kernel recover dropped part of the pinctrl compatible patch update filenames refresh patches] Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: group dts backports by upstream kernel versionRafał Miłecki2021-02-254-1/+6
| | | | | | It's a simple renaming thing. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: rename IMAGE_PREFIX/IMAGE_NAME to DEVICE_IMG_*Adrian Schmutzler2021-02-251-1/+1
| | | | | | | | | | | | | | We so far had two variables IMG_PREFIX and IMAGE_PREFIX with different content. Since these names are obviously quite confusing, this patch renames the latter to DEVICE_IMG_PREFIX, as it's a device-dependent variable, while IMG_PREFIX is only (sub)target-dependent. For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as that's a device-dependent variable as well. Cc: Paul Spooren <mail@aparcar.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.97John Audia2021-02-111-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: bcm27xx 950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch bcm53xx 180-usb-xhci-add-support-for-performing-fake-doorbell.patch layerscape 302-dts-0008-arm64-dts-ls1046a-accumulated-change-to-ls1046a-boar.patch 820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch 820-usb-0018-MLK-18794-1-usb-host-xhci-add-.bus_suspend-override.patch Build system: x86_64 Build-tested: bcm27xx/bcm2711, ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions/everything functional. Signed-off-by: John Audia <graysky@archlinux.us> [remove quilt comment, fix/adjust 820-usb-* layerscape patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-104-15/+6
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: use default SUPPORTED_DEVICES for Meraki MR32Adrian Schmutzler2021-01-231-3/+1
| | | | | | | | Since the new global SUPPORTED_DEVICES are now available in bcm53xx as well, we do not need to specify an explicit value for the MR32 anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 10:36:18 +0000