aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/bcm53xx/patches-5.10
Commit message (Collapse)AuthorAgeFilesLines
* bcm53xx: add support for Meraki MR26Christian Lamparter2022-07-151-0/+242
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Meraki MR26 is an EOL wireless access point featuring a PoE ethernet port and two dual-band 3x3 MIMO 802.11n radios and 1x1 dual-band WIFI dedicated to scanning. Thank you Amir for the unit and PSU. Hardware info: SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz) RAM : SK hynix Inc. H5TQ1G63EFR, 1 Gbit DDR3 SDRAM = 128 MiB NAND : Spansion S34ML01G100TF100, 1 Gbit SLC NAND Flash = 128 MiB ETH : 1 GBit Ethernet Port - PoE WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn WIFI3 : Broadcom BCM43428 abgn (1x1:1 - id: 43428) BUTTON: one reset button LEDS : RGB-LED MISC : Atmel AT24C64 8KiB EEPROM (i2c - seems empty) : Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor : TPS23754, High Power/High Efficiency PoE Interface+DC/DC Controller SERIAL: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated right angle 1x4 0.1" pinheader. The pinout is: VCC (next to J3, has little white arrow), RX, TX, GND. This flashing procedure for the MR26 was tested with firmware: "22-143410M-gf25cbf5a-asa". U-Boot 2012.10-00063-g83f9fe4 (Jun 04 2014 - 21:22:39) A guide how to open up the device is available on the wiki: <https://openwrt.org/toh/meraki/mr26> Notes: - The WIFI do work to a degree. Limited to 802.11bg in the 2.4GHz band. - the WIFI macs are made up. 0. Create a separate Ethernet LAN which can't have access to the internet. Ideally use 192.168.1.2 for your PC. The new OpenWrt firmware will setup the network via DHCP Discovery, so make sure your PC is running a DHCP-Server (i.e.: dnsmasq) '# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50 Download the openwrt-meraki-mr26 initramfs file from openwrt.org and rename it to something simple like mr26.bin. Then put it into the tftp's server directory. 1. Disassemble the MR26 device by removing all screws (4 screws are located under the 4 rubber feets!) and prying open the plastic covers without breaking the plastic retention clips. Once inside, remove the plastic back casing. Be careful, there some "hidden" retention clips on both sides of the LAN port, you need a light to see those. Next, you want to remove all the screws on the outer metal shielding to get to the PCB. It's not necessary to remove the antennas! 2. Connect the serial cable to the serial header and Ethernet patch cable to the device. 4. Before connecting the power, get ready flood the serial console program with the magic: xyzzy . This is necessary in order to get into the u-boot prompt. Once Ready: connect power cable. 5. If you don't get the "u-boot>" prompt within the first few seconds, you have to disconnect and reconnect the power cable and try again. 6. In the u-boot prompt enter: setenv ipaddr 192.168.1.4 setenv serverip 192.168.1.2 tftpboot ${meraki_loadaddr} mr26.bin; bootm this will boot a in-ram-only OpenWrt image. 7. Once it booted use sysupgrade to permanently install OpenWrt. To do this: Download the latest sysupgrade.bin file and move it to the device. Then use sysupgrade *sysupgrade.bin to install it. WARNING: DO NOT DELETE the "storage" ubi volume! Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 5.10 to 5.10.125John Audia2022-06-271-1/+1
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.122John Audia2022-06-271-1/+1
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* bcm53xx: disable GRO by default at kernel levelRafał Miłecki2022-06-241-0/+36
| | | | | | | | | | This improves NAT masquarade network performance. An alternative to kernel change would be runtime setup but that requires ethtool and identifying relevant network interface and all related switch ports interfaces. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: revert bgmac back to the old limited max frame sizeRafał Miłecki2022-06-151-0/+33
| | | | | | | | | | | Bumping max frame size has significantly affected network performance. It was done by upstream commit that first appeared in the 5.7 release. This change bumps NAT masquarade speed from 196 Mb/s to 383 Mb/s for the BCM4708 SoC. Ref: f55f1dbaad33 ("bcm53xx: switch to the kernel 5.10") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: remove MR32's specific get_leds_dt codeChristian Lamparter2022-05-141-28/+0
| | | | | | | the existing diag.sh code will pick up the LED by itself. This is not/no longer needed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 5.10 to 5.10.110John Audia2022-04-091-3/+3
| | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-5.10/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch generic/pending-5.10/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch ipq40xx/patches-5.10/105-ipq40xx-fix-sleep-clock.patch All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Compile-/run-tested: ath79/generic (Archer C7 v2). Signed-off-by: John Audia <graysky@archlinux.us>
* bcm53xx: add switch ports for Buffalo WZR-900DHP & re-enable itSHIMAMOTO Takayoshi2022-03-301-0/+44
| | | | | | | | | | Specify the switch ports in the DTS file. Re-enable it after it was disabled by commit e9672b1a8fa4 ("bcm53xx: switch to the upstream DSA-based b53 driver"). Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com> [rmilecki: reword commit & drop unneeded whitespace change] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport DT changes from 5.17 & 5.18Rafał Miłecki2022-03-309-1/+471
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.10 to 5.10.104John Audia2022-03-131-3/+3
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.92Rui Salvaterra2022-01-161-2/+2
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.83John Audia2021-12-1213-69/+14
| | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1] bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6 Build system: x86_64* Build-tested: bcm2711/RPi4B, ipq806x/R7800† Run-tested: bcm2711/RPi4B, ipq806x/R7800† * Had to revert 7c99085bd69742f66207d61e9f2da5ec4f8f9d2f in order to build (latest bump of ca-certificates) † Had to revert 7f1edbd41295dff9f2127b169fbc086c0fb2c14e in order to build (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149) Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.82John Audia2021-11-273-42/+2
| | | | | | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/033-v5.16-0014-ARM-dts-NSP-Fix-mpcore-mmc-node-names.patch Manually rebased: ipq806x/patches-5.10/086-ipq8064-fix-duplicate-node.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* bcm53xx: fix platform clocks & USB 2.0 PHYRafał Miłecki2021-11-231-0/+62
| | | | | | | | This fixes WARNing, missing clocks and [ 10.422481] bcm_ns_usb2 1800c164.usb2-phy: Clock not defined Fixes: 5901917b936d ("bcm53xx: use more upsteam DT patches from 5.16 / 5.17") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use new USB 2.0 PHY bindingRafał Miłecki2021-11-232-0/+183
| | | | | | | | | | | This fixes: [ 10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff] [ 10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs [ 10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16 caused by conflict in allocating resources. Fixes: f55f1dbaad33 ("bcm53xx: switch to the kernel 5.10") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: specify switch ports on TP-LINK devicesRafał Miłecki2021-11-221-0/+92
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.10 to 5.10.80Rui Salvaterra2021-11-191-158/+0
| | | | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch [1] bcm53xx/patches-5.10/033-v5.15-0012-ARM-dts-BCM5301X-Fix-memory-nodes-names.patch [2] lantiq/patches-5.10/0016-mtd-rawnand-xway-Keep-the-driver-compatible-with-on-.patch [3] lantiq/patches-5.10/0110-MIPS-lantiq-dma-add-small-delay-after-reset.patch [4] lantiq/patches-5.10/0111-MIPS-lantiq-dma-reset-correct-number-of-channel.patch [5] lantiq/patches-5.10/0112-MIPS-lantiq-dma-fix-burst-length-for-DEU.patch [6] Manually rebased: ipq806x/patches-5.10/0065-arm-override-compiler-flags.patch [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=47462c5e600fbaffd755cd13dedd80d04e41ff83 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=2fde76df1885a6bec04317e457121326070450eb [3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=9b366f5221d8aa64b22f35be137a5749326444ce [4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=5af57ce8a6155fe3e4270d28d171abf8903bebc0 [5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=b92a5df2c7adc79a57481445f67de0c1c716581f [6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=6b72caabc47011d03f44064452b2c65e8ed18326 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm53xx: use more upsteam DT patches from 5.16 / 5.17Rafał Miłecki2021-11-184-9/+116
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: drop patch for downstream swconfig-based b53Rafał Miłecki2021-11-081-53/+0
| | | | | | | It isn't used anymore so there is no need to hack CPU port. Upstream (DSA-based) b53 also supports all switch ports just fine. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: drop downstream patch for Buffalo WZR-1750DHP buttonRafał Miłecki2021-11-081-20/+0
| | | | | | | | | This patch never received a proper description and was never sent upstream as supposed. It was meant to be handled in 2015-2018 so it should be safe to assume noone really understands it or care. Cc: Felix Fietkau <nbd@nbd.name> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.10 to 5.10.77Rui Salvaterra2021-11-061-106/+0
| | | | | | | | | Deleted (upstreamed): bcm53xx/patches-5.10/081-v5.15-Revert-pinctrl-bcm-ns-support-updated-DT-binding-as-.patch [1] [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=01c2881bb0e0a71b87ca425e1b763ac13855aa7e Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm53xx: add first 5.17 DTS changesRafał Miłecki2021-11-045-7/+177
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.10 to 5.10.76Rui Salvaterra2021-10-301-3/+3
| | | | | | | | | | | | | | | | Deleted (upstreamed): bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1] Manually rebased: bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch Note: although automatically rebaseable, the last patch has been edited to avoid conflicting bit definitions. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm53xx: MR32: replace i2c-gpio with SoC's i2cChristian Lamparter2021-10-302-0/+117
| | | | | | | | | During review of the MR32, Florian Fainelli pointed out that the SoC has a real I2C-controller. Furthermore, the connected pins (SDA and SCL) would line up perfectly for use. This patch swaps out the the bitbanged i2c-gpio with the real deal. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: backport patch fixing pinctrl driverRafał Miłecki2021-10-292-33/+106
| | | | | | | This switches pinctrl driver to use the old & good DT binding. There is no more need to adjust upstream DTS file. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport bgmac upstream commits from 5.15 / for 5.16Rafał Miłecki2021-10-071-41/+0
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.10 to 5.10.70Rui Salvaterra2021-09-301-41/+0
| | | | | | | Deleted (upstreamed): bcm53xx/patches-5.10/181-Revert-USB-bcma-Add-a-check-for-devm_gpiod_get.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.69Rui Salvaterra2021-09-301-6/+1
| | | | | | Patches automatically refreshed. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.65Rui Salvaterra2021-09-301-2/+2
| | | | | | | | | Manually refreshed: generic/pending-5.10/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm53xx: MR32: read mac-address from eepromChristian Lamparter2021-09-231-0/+46
| | | | | | | | Meraki wrote the ethernet MAC-address of the device onto the eeprom (AT24C64) at the fixed location 0x66 to 0x6C. Let's fetch it from there. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: backport early DT patches queued for 5.16Rafał Miłecki2021-09-2312-4/+642
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: drop DTS based workaround for serial support in procdRafał Miłecki2021-09-161-116/+0
| | | | | | | | | Specifying serial in bootargs is not needed since the commit ffeb37047e85 ("procd: update to git HEAD"). It's thanks to the procd commit 2cfc26f8456a ("inittab: detect active console from kernel if no console= specified"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.10 to 5.10.64John Audia2021-09-131-1/+1
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* bcm53xx: specify switch ports for more devicesRafał Miłecki2021-09-072-0/+864
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix USB in kernel 5.10Rafał Miłecki2021-08-311-0/+41
| | | | | | | This makes USB controller driver work with USBs that are always powered on (don't require toggling any GPIO). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport missed DT patch cleaning up CRU blockRafał Miłecki2021-08-307-11/+98
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: backport the latest upstream DT changesRafał Miłecki2021-08-2919-1/+1938
| | | | | | | | This includes: 1. BCM5301X changes from 5.14 and queued 5.15 stuff 2. NSP changes from 5.11 - 5.15 for kernel 5.10 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.10 to 5.10.55Rui Salvaterra2021-08-084-5/+5
| | | | | | No deleted or manually refreshed patches. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm53xx: add testing support for kernel 5.10Rafał Miłecki2021-07-2930-0/+1987
It still requires fixing PCIe support: [ 6.644699] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges: [ 6.652217] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff] [ 6.661833] OF: /axi@18000000/pcie@12000: Missing device_type [ 6.667622] pcie_iproc_bcma: probe of bcma0:7 failed with error -12 [ 6.673985] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges: [ 6.681514] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff] [ 6.691137] pcie_iproc_bcma: probe of bcma0:8 failed with error -12 [ 6.697522] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges: [ 6.705048] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff] [ 6.714669] pcie_iproc_bcma: probe of bcma0:9 failed with error -12 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2025-02-16 01:44:00 +0000