aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx/ath79: fix mtd corruptionFabio Bettoni2018-10-171-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit fec8fe806963 ("kernel: bump 4.9 to 4.9.116") [1], the following patch for removed: - 403-mtd_fix_cfi_cmdset_0002_status_check.patch This patch contained fixes for both write and erase functions. While the chip-detects for erase got fixed upstream [2], some modifications are still required, even with the fixes applied. While at it, also apply the same fix for target ath79, which suffers the same issue. Not doing so results in following errors seen: Collected errors: * pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error. * opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain! * opkg_install_cmd: Cannot install package luci-ssl. * opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error. [ 0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 8.423476] mount_root: switching to jffs2 overlay [ 270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962 [ 270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0 [ 270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero [ 270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0 [ 270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero [ 270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0 [ 270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero [ 270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0 [ 270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero [1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe Fixes: fec8fe806963 ("kernel: bump 4.9 to 4.9.116") Signed-off-by: Fabio Bettoni <fbettoni@gmail.com> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-164-1/+7
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.14 to 4.14.75Koen Vandeputte2018-10-101-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add Fritz!Box 4020 switchconfigDavid Bauer2018-10-071-1/+5
| | | | | | In contrast to ar71xx, uci switchconfig is missing in the ath79 target. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WA901ND v2David Bauer2018-10-073-0/+140
| | | | | | | | | | | | | | | | | | This commit adds support for the TP-Link TL-WR901ND v2 access point. CPU: Atheros AR9132 400MHz RAM: 32MB FLASH: 4MiB WiFi: Atheros AR9103 3x3:2 bgn LED: Power (static on) LAN (controlled by PHY) SYS, WiFi, QSS toggleable BTN: Reset, QSS Installation: Upload the factory image via the vendor-GUI. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Buffalo WZR-HP-G302H A1A0INAGAKI Hiroshi2018-10-074-0/+263
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros AR7242. It is Japanese market model of WZR-HP-G300NH2, but there are some diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx. And, G302H has several hardware versions and hardware is different dependent on the versions. This commit adds support for "A1A0" version. Specification: - Atheros AR7242 - 64 MB of RAM (DDR2) - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 2.4 GHz 2T2R wifi - Atheros AR9283 - 5x 10/100/1000 Mbps Ethernet - Atheros AR8316 - 7x LEDs, 5x keys - LED: 1x gpio-leds, 6x ath9k-leds - key: 3x buttons, 2x slide switches - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/" and move to firmware update page ("ファーム更新") 3. Select the OpenWrt factory image and click update ("更新実行") button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add hwver parameter to buffalo-tagINAGAKI Hiroshi2018-10-073-5/+6
| | | | | | | In order to be able to set the value of "hardware version" other than "3", I added the "hwver" parameter. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Add support for TP-Link TL-WR842N-v2Robert Marko2018-10-074-1/+221
| | | | | | | | | | | | | | | | | | | | This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79. This is a low cost model with following specs: CPU: Atheros AR9341 SoC RAM: 32 MB DDR1 Flash: 8 MB NOR SPI Switch: Internal AR9341 5 port 10/100 Mbit Ports: 5x 10/100 Mbit(1x WAN, 4x LAN) USB: 1x USB2.0 WLAN: 2.4 GHZ AR9341 Installation: Simply flash the factory image through stock firmware WEB UI. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath79: fix build warningMathias Kresin2018-10-071-2/+0
| | | | | | | | | | | | | | | | | | | | The image build code for the Ubiquiti Nanostation AC series adds the factory image as to be build image. The same is already done by an included recipe which results into an expanded IMAGE variable of: IMAGES = sysupgrade.bin factory.bin factory.bin The build system doesn't like these duplicates and issues the following warning: Makefile:82: warning: overriding recipe for target... Get remove the duplicate factory image to get rid of the warning. Fixes: 5736af8024be ("ath79: Add support for Ubiquiti NanoStation AC loco") fa3c2676ab0c ("ath79: Add support for Ubiquiti Nanostation AC") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Add support for Ubiquiti Nanostation ACTobias Schramm2018-10-076-0/+117
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: Add support for Ubiquiti NanoStation AC locoTobias Schramm2018-10-074-3/+66
| | | | | | | | | | | | | | | | | | | | | | | Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: Add generic device tree for Ubiquiti WA boardsTobias Schramm2018-10-071-0/+92
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: fix MAC address for Buffalo BHR-4GRVINAGAKI Hiroshi2018-10-073-2/+8
| | | | | | | | | | | | | | | | | | I added mtd-mac-address for WZR-HP-G450H and BHR-4GRV in 1df1ea4d7e8b6ae3351780ed58800ccd9edd4c27, but that address in ART is incorrect for BHR-4GRV. WZR-HP-G450H has wlan eeprom and MAC address in ART, but BHR-4GRV has only MAC address in ART. - WZR-HP-G450H - eeprom: 0x1000 - MAC: 0x1002 - BHR-4GRV - MAC: 0x0 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 4.14 to 4.14.73Koen Vandeputte2018-10-021-2/+2
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for Buffalo BHR-4GRVINAGAKI Hiroshi2018-09-263-5/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV is a wired router, based on Atheros AR7242. Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 2x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the BHR-4GRV normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware upgrade 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix support for Buffalo WZR-HP-G450H and split to dts/dtsiINAGAKI Hiroshi2018-09-264-81/+225
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are many parts that are incorrect or missing in the current code for Buffalo WZR-HP-G450H in ath79, so its support is broken. I fixed that issues and split to dts/dtsi files to add support for Buffalo BHR-4GRV. And WZR-450HP has the same hardware as WZR-HP-G450H, so I change the device name to "WZR-HP-G450H/WZR-450HP". Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 3T3R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 5x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the WZR-HP-G450H (or WZR-450HP) normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix wrong pll-data value for I-O DATA WN-AC-DGR devicesINAGAKI Hiroshi2018-09-261-1/+1
| | | | | | | | The pll-data value "0x56000000" is wrong for I-O DATA WN-AC1600DGR2 and WN-AC1167DGR, so there was a problem of slowing down the speed of ethernet. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mac80211: make ath10k-ct the default ath10kJohn Crispin2018-09-263-9/+9
| | | | | | | | We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 4.14 to 4.14.72Koen Vandeputte2018-09-262-38/+3
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 203-MIPS-ath79-fix-restart.patch - 0013-MIPS-ath79-fix-system-restart.patch - 180-earlycon-initialize-port-uartclk-based-on-clock-frequency-property.patch - 181-earlycon-remove-hardcoded-port-uartclk-initialization-in-of_setup_earlycon. patch - 700-1-6-e1000e-Remove-Other-from-EIAC.patch - 700-2-6-Partial-revert-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - 700-3-6-e1000e-Fix-queue-interrupt-re-raising-in-Other-interrupt.patch - 700-4-6-e1000e-Avoid-missed-interrupts-following-ICR-read.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: Fix GL-AR300M USB triggerRobert Marko2018-09-221-1/+1
| | | | | | Correct a typo preventing USB trigger to work on AR300M. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath79: flag FritzBox 4020 buttons as active lowDavid Bauer2018-09-221-2/+2
| | | | | | | | | Buttons of AVM FritzBox 4020 are incorrectly flagged as active high. This was an oversight as RFKill button was working as expected even with incorrectly flagged GPIO. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.71Koen Vandeputte2018-09-211-5/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.70Koen Vandeputte2018-09-171-4/+4
| | | | | | | | | | | | | | | Refreshed all patches. Added new patch: - 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch This fixes a bug introduced in upstream 4.14.68 which caused targets using ubifs to produce file-system errors on boot, rendering them useless. Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: ubnt-xm: add rssileds packageLech Perczak2018-09-101-1/+1
| | | | | | | | In order to make RSSI indicator on the device work out of box, include "rssileds" package in per-device rootfs image by default for Ubiquiti XM family. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: create RSSI monitor on wlan0Lech Perczak2018-09-101-0/+1
| | | | | | | | | When mapping for RSSI LEDs was defined for interface wlan0 on Ubiquiti XM family, the mapping for rssileds monitor was omitted by mistake. Therefore create the mapping, so RSSI LEDs work without additional configuration, after starting rssileds service. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for Buffalo WZR-HP-AG300HBernhard Frauendienst2018-09-107-27/+336
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-AG300H is a dual band router based on Qualcom Atheros AR7161 rev 2 Specification: - 680 MHz CPU (Qualcomm Atheros AR7161) - 128 MiB RAM (2x Samsung K4H511638G-LCCC) - 32 MiB Flash (2x Winbond 25Q128BVFG) - WiFi 5 GHz a/n (Atheros AR9220) - WiFi 2.4 GHz b/g/n (Atheros AR9223) - 1000Base-T WAN (Atheros AR7161) - 4x 1000Base-T Switch (Atheros AR8316) - 1x USB 2.0 - 3 Buttons (AOSS/WPS, Reset, USB Eject) - 2 Slide switches (Router (on/off/auto), Movie Engine (on/off)) - 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber, WLAN 5GHz green, WLAN 5GHz LED amber, Router green, Diag red, Movie Engine blue, USB green) It is already supported by the ar71xx target. For more information on the device visit the wiki: <https://openwrt.org/toh/buffalo/wzr-hp-ag300h> Serial console: - The UART Header is next to Movie Engine Switch. - Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V) - The Serial setting is 115200-8-N-1. Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.11.1 - Go to “Administration” → “Firmware Upgrade” - Upload the OpenWrt factory image Tested: - Ethernet (LAN, WAN) - WiFi - Installation - via TFTP rescue - via factory image - on firmware v1.77 (28-05-2012) - on pro firmware v24SP2 r30356 (26-03-2018) - via sysupgrade from ar71xx (wlan devices don't work because of new names) - via sysupgrade from itself - Buttons - LEDS - USB (Power control and device recognition) Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
* ath79: add support for ELECOM WRC-300GHBK2-IINAGAKI Hiroshi2018-09-103-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 4x keys(connected to GPIO: 3x) - UART header on PCB - TX, GND, RX, Vcc from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot the WRC-300GHBK2-I normaly and connect the computer to its LAN port 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with squashfs-sysupgrade image for WRC-300GHBK2-I 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for WD My Net Wi-Fi Range ExtenderChristian Lamparter2018-09-105-1/+221
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch ports over support for the device from ar71xx. SOC: AR7370 (Wasp - AR9344 rev2 0001974c) RAM: Winbond W9725G6KB-25 32MiB FLASH: Winbond 25Q64FVSIG 8MiB WLAN: AR9380 Dual-Band 802.11abgn 3x3:3 INPUT: WPS, RESET button (hardware on/off toggle button) LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high) Serial: Header Next to the winbond flash chip (labeld JP1) Pinout is GND - NC - RX - TX - 3V3 (JP1) The Serial setting is 115200-8-N-1. - Installation via uboot's upgrade command 0. attach serial cable 1. interrupt uboot and enter "upgrade code.bin" into the u-boot prompt ar7240> upgrade code.bin 2. rename openwrt...sysupgrade.bin to code.bin on PC 3. run a tftp-client on the PC (shell)$ tftp 192.168.1.230 binary put code.bin 4. wait for the device to finish [...] Copy buff to Flash from 0x9f040000 length 0x79f000 Copy to Flash... write addr: 9f040000 done 5. enter "go" in the u-boot prompt ar7240> go - TFTP ramdisk image boot from the uboot prompt (tftp server defaults to serverip 192.168.1.254) => tftpboot 81000000 initramfs.bin => bootm Tested and working: - LEDs - Buttons - Ethernet - Wi-Fi - OpenWRT sysupgrade For flashing and debricking information see: <https://openwrt.org/toh/wd/rext> Users coming from ar71xx can use sysupgrade too. But I highly advise to no save the old configuration and start from a clean state. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: port cybertan_part from ar71xxChristian Lamparter2018-09-103-0/+183
| | | | | | | | | | | | | This patch ports the cybertan_part code from ar71xx and converts the driver to a DT-supported mtd parser. As a result, it will no longer add the u-boot, nvram and art partitions, which were never part of the special Cybertan header. Instead these partitions have to be specified in the DT, which has the upside of making it possible to add properties (i.e.: read-only), labels and references to these important partitions. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: fix unaligned access panic in ag71xx_mdio_probeMatt Merhar2018-09-061-2/+2
| | | | | | | | | | | Without "syscon" being present in an ag71xx ethernet DT node's compatible property, a panic occurs at boot during probe citing "Unhandled kernel unaligned access". With this modification, the panic no longer occurs and instead the probe simply fails, allowing the boot process to continue. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* ath79: add syscon compatible property to ar7100 ethernet nodesMatt Merhar2018-09-062-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds "syscon" to the compatible properties for the eth0/eth1 nodes in ar7100.dtsi. Without this, a kernel panic is encountered on boot with some ar7100 boards. This for some reason wasn't an issue for the WNDR3800, which uses a Realtek switch chipset, but the panic was encountered on the RouterStation Pro (using an AR8216 switch) and some other boards that haven't yet been merged. The panic message mentions an unaligned access and happens in ag71xx_mdio_probe in drivers/net/ethernet/atheros/ag71xx/ag71xx_mdio.c. Even if the unaligned access is fixed, the ag71xx_mdio probe still fails without the "syscon" property. This was already being worked around in ar7161_ubnt_routerstation-pro.dts by overriding the compatible property, so this commit removes that as well. All of the other ath79 .dtsi already have this property, so no changes are needed elsewhere. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* kernel: bump 4.14 to 4.14.67Koen Vandeputte2018-08-284-15/+11
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed patches: - 037-v4.18-0008-ARM-dts-BCM5301x-Fix-i2c-controller-interrupt-type.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: fix remove irq code from pci driver patchJohn Crispin2018-08-281-0/+141
| | | | | | This patch got mangled in the void while rebasing it. Signed-off-by: John Crispin <john@phrozen.org>
* ath79: fix ar7100 PCI IRQ handlingDmitry Tunin2018-08-282-5/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently all PCI devices get the same IRQ that affects performance badly. This commit adresses this problem and cleans the code. ar7100 has a special PCI interrupt controller@18060018 that works exactly the same way as misc interrupt controller. This patch does the following: 1. Defines pci-intc interrupt controller@18060018 in dtsi. 2. Removes interrupt-controller property from PCI node. 3. Sets a correct interrupt mask for PCI devices. 4. Removes all IRQ handling code from the PCI driver. "qca,ar7100-misc-intc" should be used as the compatible property, becuase on ar7100 the controlled status register is read-only and the ack method used in "qca,ar7240-misc-intc" won't work properly. There are two very minor downsides of this patch that don't affect perormance: 1. We allocate an IRQ domain of 32 IRQ, whan we need only 5. But ar7100 aren't tiny un terms of RAM and that is not very important and can be tuned if we implement "nr-interrupts" property". 2. It reuses the same irg chip name "MISC" for both controllers. Run tested on DIR-825 B1. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: ag71xx: apply interface mode to MII0/1_CTRL on ar71xx/ar913xChuanhong Guo2018-08-284-0/+73
| | | | | | | | | | | | | We currently don't have any code configuring interface mode in ath79, meaning that we relies on bootloader to set the correct interface mode. This patch added code to set interface correctly so that everything works even if bootloader configures it wrong.(e.g. on WNDR3800 u-boot set the second GMAC mode to RMII but it should be RGMII.) Introduced "qca,mac-idx" for the difference in MII_CTRL register value. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: replace patchesJohn Crispin2018-08-2835-1322/+1332
| | | | | | | replace our downstream version of the patches with the ones that were sent upstream. Signed-off-by: John Crispin <john@phrozen.org>
* ath79: initial support for Ubiquiti RouterStation and RouterStation ProMatt Merhar2018-08-277-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other .dts files that utilize it, ar7161_ubnt_routerstation.dts and ar7161_ubnt_routerstation-pro.dts. The modifications to generic-ubnt.mk, config-default, and base-files necessary for image generation, parsing RedBoot FIS partitions, network configuration, and sysupgrade are also included. This reintroduces vital bits from platform_do_upgrade_combined() and its supporting functions to /lib/upgrade/platform.sh, which were previously removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79: sysupgrade: drop unused platform checks". The new function is called "routerstation_do_upgrade" and will *only* work for the RouterStation series of boards. It does however retain the ability to downgrade (e.g. from master -> 17.01.x using sysupgrade -F). All hardware is functional including the AR8216 switch (for the Pro), wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button, and LED. Switch and LAN/WAN configuration is the same as it is with the equivalent ar71xx targets. MAC addresses are assigned based upon the content stored in the RedBoot config partition. Flashing via both sysupgrade and TFTP has been confirmed to work. Also, the initramfs images are now raw .bin files instead of being wrapped in a uImage (as they currently are in ar71xx), which makes them bootable with RedBoot. One notable difference to ar71xx is the inclusion of the RedBoot "fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD parser’s DT binding, whose proper usage is mutually exclusive to defining a separate fixed-partitions node for "RedBoot config". This config partition contains the board's base MAC address. The lack of a hard-coded flash location means that the mtd-mac-address property cannot be used in the .dts, so instead fconfig is used to read the MAC addresses from flash in userspace during first boot. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* treewide: fix some cosmetic glitches in dts filesPaul Wassi2018-08-279-14/+1
| | | | | | | | | | | - fix single spaces hidden by a tab - replace indentation with spaces by tabs - make empty lines empty - drop trailing whitespace - drop unnecessary blank lines Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix mac address increment for embedded wireless DorinFelix Fietkau2018-08-251-0/+1
| | | | | | Use mtd-mac-address-increment-byte to match ar71xx behavior Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: ubnt-xm: create mapping for RSSI LEDsLech Perczak2018-08-231-0/+7
| | | | | | | | | | Ubiquiti XM series boards contain a set of RSSI LEDs. Create an UCI mapping for them, so visual feedback on RSSI is available, when using userspace RSSI monitor daemon. Runtime tested using rssileds. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: hijack LED4 as booting/failsafeLech Perczak2018-08-231-1/+6
| | | | | | | | | | Create aliases for led-booting and led-failsafe pointing at ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback on device status becomes available, in order to enter failsafe mode via button. led-running and led-upgrade aliases are omitted to avoid conflicting with RSSI LEDs when in normal operation. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: disable WAN on (rocket|bullet)-mLech Perczak2018-08-231-0/+2
| | | | | | | | | | | ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet port, therefore disable creation of WAN zone and interfaces for them, as their intended purpose is a wireless bridge. This aligns the configuration with one found in ar71xx target. ubnt,nano-m target is kept as is, being a two-port device. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: support ath9k firmware loadingLech Perczak2018-08-231-0/+5
| | | | | | | | Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards. This is required for wireless interface to function. Runtime tested on Nanobridge M5. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for I-O DATA ETG3-RINAGAKI Hiroshi2018-08-233-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA ETG3-R is a wired router, based on Atheros AR9342. Specification: - Atheros AR9342 - 64 MB of RAM - 8 MB of Flash - 5x 10/100/1000 Ethernet - AR8327N - 2x LEDs, 1x key - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using initramfs image: 1. Connect serial cable to UART header on ETG3-R 2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in the TFTP directory 3. Set IP address of the computer to 192.168.0.10, connect to the LAN port of ETG3-R, and start the TFTP server on the computer 4. Connect power cable to ETG3-R and turn on the router 5. Press "Enter" key when the "Hit any key to stop autoboot:" message is displayed on the console and enter the u-boot cli 6. execute following commands to change kernel address for u-boot setenv bootsf 1 setenv mtd_kernel1 "bootm 0x9f050000" saveenv 7. execute "tftpboot; bootm" command to download the initramfs image from TFTP server and boot with it 8. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for ETG3-R 9. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix TL-MR3020 image metadataDavid Bauer2018-08-191-1/+1
| | | | | | | | | | Sysupgrading to ath79 from ar71xx currently fails because of mismatching supported_devices. ar71xx is expecting "tl-mr3020" which is missing in the ath79 image. Upgrading from ath79 is unaffected, as the image contains the old string for ar71xx and the new one coming from the device-tree. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: cleanup PISEN WMM003N image metadataChuanhong Guo2018-08-191-1/+0
| | | | | | | PISEN WMM003N is never supported by ar71xx, this commit also removed SUPPORTED_DEVICES for it because it's completely useless. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Fritz!Box 4020David Bauer2018-08-195-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs The USB port doesn't work. Both Root Hubs are detected as having 0 Ports: [ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.723267] usbcore: registered new interface driver usbfs [ 3.729058] usbcore: registered new interface driver hub [ 3.734616] usbcore: registered new device driver usb [ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.758357] SCSI subsystem initialized [ 3.766026] ehci-platform: EHCI generic platform driver [ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller [ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00 [ 3.824001] hub 1-0:1.0: USB hub found [ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller [ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00 [ 3.894011] hub 2-0:1.0: USB hub found [ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.908928] usbcore: registered new interface driver usb-storage [ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/* A few words about the shift-register: AVM used a trick to control the shift-register for the LEDs with only 2 pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple shift-registers, pulls the latch, moving the shift register-state to the storage register. It also pulls down MR (normally pulled up) to clear the storage register, so the latch gets released and will not be pulled by the remaining bits in the shift-register. Shift register is all-zero after this. For that we need to make sure output 7 is set to high on driver probe. We accomplish this by using gpio-hogging. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer C7 v1Christian Lamparter2018-08-193-0/+56
| | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v1 is a dual band router based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: - 720 MHz CPU - 128 MB of RAM (Various chips) - 8 MB of FLASH (Various chips) - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi - minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!) - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch) - 10x LEDs, 2x software buttons For further informwation on the device, visit the wiki: <https://openwrt.org/toh/tp-link/archer-c7-1750> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for I-O DATA WN-AC1167DGRINAGAKI Hiroshi2018-08-167-208/+245
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz wifi - 2.4 GHz: SoC internal - 5 GHz: QCA988x - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1167DGR 2. Connect power cable to WN-AC1167DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix leds and network for TP-Link TL-WR841 v9/v11Johann Neuhauser2018-08-162-7/+5
| | | | | | | | | Adding tl-wr841-v11 and the rename of tl-wr841n-v9 to tl-wr841-v9 in 01_leds and 02_network script files are missing in commits cc35c91 and 8db6522. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de> [merged with identical case in 02_network] Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 17:04:17 +0000