aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.19 to 4.19.98Koen Vandeputte2020-01-244-6/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.167Koen Vandeputte2020-01-243-5/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: fix SUPPORTED_DEVICES not matching ar71xx board namesAdrian Schmutzler2020-01-234-12/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: move lzma-loader to the end of available RAMAdrian Schmutzler2020-01-232-3/+2
| | | | | | | | | | | | | | | | | | | | | In certain cases, the uncompressed initramfs image will overwrite the lzma-loader, which is currently only 10 MB away from kernel image start. To prevent this, change LZMA_TEXT_START to 24 MB, so loader and compressed image have 8 MB at the end of RAM and uncompressed image has 24 MB available. This is only enabled for ath79 at the moment, as there we can be sure that all devices have 32+ MB RAM and TARGET_INITRAMFS_COMPRESSION_LZMA is not enabled there. Despite, since lzma-loader is currently build specifically for ath79 anyway, there is no need to re-specify LOADADDR and LZMA_TEXT_START in image/Makefile, so the values are set directly in image/lzma-loader/Makefile and the overwrite in image/Makefile is removed. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for MikroTik RouterBOARD wAP G-5HacT2HnDRoger Pueyo Centelles2020-01-239-3/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet port. See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info. Specifications: - SoC: Qualcomm Atheros QCA9556 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive PoE in Working: - Board/system detection - Sysupgrade - Serial console - Ethernet - 2.4 GHz radio - 5 GHz radio and LED - Reset button Not working/Unsupported: - 2.4 GHz LED - AP/CAP LED - ZT2046Q SPI temperature and voltage sensor This adds the basic features for supporting MikroTik devices: - a common recipe for mikrotik images in common-mikrotik.mk - support for minor (MikroTik NOR) split firmware (only for generic subtarget so far) Acknowledgments: Robert Marko <robimarko@gmail.com> Andrew Cameron <apcameron@softhome.net> Koen Vandeputte <koen.vandeputte@ncentric.com> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: allow to override AR8033 SGMII aneg statusDavid Bauer2020-01-232-0/+32
| | | | | | | | | | | | | In order to make the QCA955x SGMII workaround work, the unsuccessful SGMII autonegotiation on the AR8033 should not block the PHY state-machine. Otherwise, the ag71xx driver never becomes aware of the copper-side link-establishment and the workaround is never executed. Signed-off-by: David Bauer <mail@david-bauer.net> [remove one trailing whitespace per file] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add QCA955x SGMII link loss workaroundDavid Bauer2020-01-233-0/+290
| | | | | | | | | | | | | | | | This commit adds a workaround for the loss of the SGMII link observed on the QCA955x generation of SoCs. The workaround originates part from the U-Boot source code, part from the implementation from AVM found in the GPL tarball for the AVM FRITZ!WLAN Repeater 450E. The bug results in a stuck SGMII link between the PHY device and the SoC side. This has only been observed with the Atheros AR8033 PHY and most likely all devices using such combination are affected. It is worked around by reading a hidden SGMII status register and issuing a SGMII PHY reset until the link becomes useable again. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-224-1/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Stock firmware uses label MAC address for WiFi and same with local bit set for ethernet. Since this is difficult to reproduce with the toolset of OpenWrt, we just keep both ethernet and WiFi to the same address here. This is the first tiny device with tplink-safeloader in ath79. Firmware partition is only 3648k and thus even smaller than for the tplink-4m(lzma) devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use upstream properties to disable EEEDavid Bauer2020-01-224-4/+8
| | | | | | | | | | | | | The hack-patch which introduced the "at803x-disable-smarteee" for disabling SmartEEE did in fact not disable SmartEEE but rather disabled 802.3az "standard" EEE. This can be done by using the upstream properties "eee-broken-100tx" and "eee-broken-1000t". EEE is then disabled by the PHY subsystem. Tested on devolo WiFi pro 1200e. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WA850RE v1Adrian Schmutzler2020-01-225-0/+182
| | | | | | | | | | | | | | | | | | | | | | This ports support for the TL-WA850RE v1 range extender from ar71xx to ath79. Specifications: Board: AP123 / AR9341 rev. 3 Flash/RAM: 4/32 MiB CPU: 535 MHz WiFi: 2.4 GHz b/g/n Ethernet: 1 port (100M) Flashing instructions: Upload the factory image via the vendor firmware upgrade option. Recovery: Note that this device does not provide TFTP via ethernet like many other TP-Link devices do. You will have to open the case if you require recovery beyond failsafe. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove usused TPLINK_BOARD_NAME variable for DEVICE_VARSAdrian Schmutzler2020-01-211-1/+1
| | | | | | | | | | | | | | TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time ago (7d6c63d87542: "build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target at all. TPLINK_BOARD_NAME seems to have been introduced into ath79 target only by mistake. It has never been used. Remove it. Fixes: 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-MR6400Enrico Mioso2020-01-214-0/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | This device is an LTE router supported in ar71xx so far. As per original commit, hardware specifications (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Flashing instructions: You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Known issues: - LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround. - eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx) Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [several adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Filip Moc <lede@moc6.cz>
* ath79: fix SUPPORTED_DEVICES for WNDR4300 and WNDR3700v4Michal Cieslakiewicz2020-01-211-2/+0
| | | | | | | | | | Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300 routers breaks sysupgrade image compatibility with ar71xx builds. Therefore, SUPPORTED_DEVICES variable has to be removed for both devices from target makefile. Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* kernel: bump 4.19 to 4.19.95Koen Vandeputte2020-01-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.164Koen Vandeputte2020-01-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add led_ prefix for Phicomm K2T LED labelAdrian Schmutzler2020-01-181-5/+5
| | | | | | | Using the led_ prefix for the node label is now common in ath79, so also apply it here. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use rssihigh LED instead of WAN LED for status indicationAdrian Schmutzler2020-01-182-10/+10
| | | | | | | | | | | | Using the LED of network interfaces for status (boot/failsafe/...) indication is somewhat misleading, as the blinking might be mistaken for network activity. This uses rssi LEDs instead, which do not blink normally and thus are less ambiguous. The rssihigh LED has also been used consistently for the TP-Link CPE devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: ar934x: use reset for usb-phy-analogJohann Neuhauser2020-01-151-2/+2
| | | | | | | | | | | | This was already available on ar71xx, but is missing on ath79. This solves the slow usb speed on TP-Link WDR3600/WDR4300 and similar, as reported in Flyspray [0], OpenWRT Forum [1] and GitHub PR [2]. [0] https://bugs.openwrt.org/index.php?do=details&task_id=2567 [1] https://forum.openwrt.org/t/usb-wdr4300-low-speed-on-external-storage/46794 [2] https://github.com/openwrt/openwrt/pull/964 Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: phy-ar7200-usb: adapt old behavior of arch/mips/ath79/dev-usb.cJohann Neuhauser2020-01-151-6/+18
| | | | | | | | | | | | Do not put usb-phy into reset if clearing the usb-phy reset or setting the suspend_override has failed. Reorder (de)asserts like in arch/mips/ath79/dev-usb.c. Add an optional reset_control "usb-phy-analog", which is needed for ar934x SoCs like in the old mach-driver arch/mips/ath79/dev-usb.c. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: use caldata partition label consistentlyAdrian Schmutzler2020-01-152-8/+8
| | | | | | | Change the caldata partition DTS node label to be consistent with the label property for some Netgear WNDR devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Netgear WNDR4500 v3Michal Cieslakiewicz2020-01-155-5/+62
| | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4500v3. Router is very similar to WNDR4300v2 and is based on the same PCB. Information gathered from various Internet sources (including https://patchwork.ozlabs.org/patch/809227/) shows following differences to WNDR4300v2: * two USB 2.0 ports with separate LEDs * USB LEDs soldered to secondary pads * WPS and RFKILL buttons soldered to secondary pads * described as N900 device with 3x3:3 MIMO for 2.4GHz radio * power supply requirement is DC 12V 2.5A * vendor HW ID suffix differs in one digit * bigger chassis Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4300 v2Michal Cieslakiewicz2020-01-156-5/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4300v2. Specification ============= * Description: Netgear WNDR4300 v2 * Loader: U-boot * SOC: Qualcomm Atheros QCA9563 (775 MHz) * RAM: 128 MiB * Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND - NOR: U-boot binary: 256 KiB - NOR: U-boot environment: 64 KiB - NOR: ART Backup: 64 KiB - NOR: Config: 64 KiB - NOR: Traffic Meter: 64 KiB - NOR: POT: 64 KiB - NOR: Reserved: 1408 KiB - NOR: ART: 64 KiB - NAND: Firmware: 25600 KiB (see notes for OpenWrt) - NAND: Language: 2048 KiB - NAND: mtdoops Crash Dump: 128 KiB - NAND: Reserved: 103296 KiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Important Notes =============== 0. NOR Flash (2 MiB) is not touched by OpenWrt installation. 1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows: all space is split between 4 MiB kernel and 124 MiB UBI areas; vendor partitions (language and mtdoops) are removed; kernel space size can be further expanded if needed; maximum image size is set to 25600k for compatibility reasons and can also be increased. 2. CPU clock is 775 MHz, not 750 MHz. 3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI device ID 0xabcd. For ath9k driver to load successfully, this is overriden in DTS with correct value for this chip, 0x0033. 4. RFKILL button is wired to AR9580 pin 9 which is normally disabled by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore 'qca,gpio-mask=<0xf6ff>' hack must be used for button to work properly. 5. USB port is always on, no GPIO for 5V power control has been identified. Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: WNDR4300: increase kernel partition to 4MMichal Cieslakiewicz2020-01-152-6/+6
| | | | | | | | | Increase kernel partition from 2 MiB to 4 MiB for Netgear WNDR routers with NAND flash. Change affects following devices: * Netgear WNDR3700 v4 * Netgear WNDR4300 Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for D-Link DIR-505David Bauer2020-01-154-0/+164
| | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the D-Link DIR-505, previously supported in ar71xx. Hardware -------- SoC: Atheros AR9330 FLASH: 8M SPI-NOR RAM: 64M WIFI: 1T1R 1SS Atheros AR9330 LED: Power green, Status red BTN: WPS, Reset Installation ------------ Currently, installation is only possible by sysupgrading from an earlier OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the original bootloader from D-Link on my device anymore, so i cannot test the factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: GL-AR750S (NOR/NAND): limit factory.img kernel size to 2 MBJeff Kletsky2020-01-151-1/+4
| | | | | | | | | | | | | | | | The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size. While sysupgrade can manage kernels up to the present limit of 4 MB, directly flashing a factory.img with a kernel size greater than 2 MB through U-Boot will result in an unbootable device. This commit uses the newly-introduced check-kernel-size build operation to prevent the output of factory.img when the kernel exceeds 2 MB in size, yet permits output of sysupgrade.img as long as the kernel is within KERNEL_SIZE := 4096k Cc: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: wlr-7100: use ath10k-ct smallbuffers package variantTomasz Maciej Nowak2020-01-151-1/+1
| | | | | | | | The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove ath10k_pci memory hacks"). As this device has low amount of RAM, switch to ath-10k-ct small buffers variant, to avoid the OOM Reaper. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add support for Ubiquiti EdgeSwitch/ToughSwitch 5XPTobias Schramm2020-01-143-0/+88
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE out on all five ports. Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: ar8327 USB: 1x USB 2.0 Ethernet: 5x GbE, 1x FE Installation of the firmware is possible either via serial + tftpboot or the factory firmware update function via webinterface. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the five switch ports. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: ``` | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ ``` Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [remove ubnt,sw compatible - fix spelling - wrap commit message - remove superfluous phy-mode property] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add generic dtsi for Ubiquiti SW boardsTobias Schramm2020-01-142-133/+143
| | | | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [remove ubnt,sw compatible] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Ubiquiti ToughSwitch/EdgeSwitch 8XPTobias Schramm2020-01-123-0/+334
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: bcm53128 USB: 1x USB 2.0 Ethernet: 8x GbE, 1x FE The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE and 48V 802.11af/at PoE out on all eight ports. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the eight switch ports. Installation of the firware is possible either via serial + tftpboot or the factory firmware update function via webinterface. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [fix whitespace issue] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Ubiquiti SW devicesTobias Schramm2020-01-121-0/+12
| | | | | | | SW devices are Ubiquit ToughSwitch and EdgeSwitch series devices. Hardware-wise they are very similar to the XM device series. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: gl-ar750s: reduce kernel size to 2M in image MakefileChuanhong Guo2020-01-111-1/+1
| | | | | | | | | | | | | | | | u-boot splits nand factory firmware at 2M offset, flash the first part as kernel into spi nor and the other part as ubi into nand flash. With previous commit increasing kernel size to 4M, generated factory firmware is broken because ubi is at 4M offset. This commit reduces kernel size definition to 2M in image Makefile, producing proper factory image. Partition size in dts is kept unchanged so that sysupgrade to a firmware with 2M+ kernel still works. Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB") Reported-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: remove unused Build/mktplinkfw-combinedAdrian Schmutzler2020-01-081-11/+0
| | | | | | Build/mktplinkfw-combined is not used anywhere, so remove it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move mktplinkfw to tplink-v1-image in image-commands.mkAdrian Schmutzler2020-01-083-36/+13
| | | | | | | | | | | | | | | | | | | | | This move the slightly different target-specific implementations of mktplinkfw from the targets to include/image-commands.mk and renames it to tplink-v1-image. Having a common version will increase consistency between implementation and will complete the tplink build command already present in the new location. Due to the slight differences of the original implementations, this also does some adjustments to the device build commands/variables. This also moves rootfs_align as this is required as dependency. Tested on: - TL-WDR4300 v1 (ath79, factory) - TL-WDR4900 v1 (mpc85xx, sysupgrade) - RE210 v1 (ramips, see Tested-by) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Christoph Krapp <achterin@googlemail.com>
* ath79: use ath10k-ct-smallbuffers for TP-Link RE355/RE450 v1Christoph Krapp2020-01-051-1/+1
| | | | | | | | | Both devices are available in 64M and 128M RAM configurations but there is no visial indication which configuration one might get. So just to be sure we properly support both configurations switch to kmod-atk10k-ct-smallbuffers. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: drop obsolete ehci hacksBjørn Mork2020-01-052-206/+0
| | | | | | | There's nothing enabling these hacks in ath79, so drop the redundant patches. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ath79: Remove mtd cfi_cmdset_0002 status check patchesTokunori Ikegami2020-01-052-124/+0
| | | | | | | | | | | | | Currently the patch only changes break to use goto statement instead. But not necessary acutually since the ret value checked after the for loop. So it is okay for the break case before changed by the patch also. This patch only reverts the following commit partially. https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e7 Note: The changes are mainly applied into the linux kernel upstream. Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.93Hauke Mehrtens2020-01-051-4/+4
| | | | | | | | | | | | | | Refreshed all patches. The patch hack-4.19/550-loop-better-discard-for-block-devices.patch was replaced with an new version of the patch from: https://lore.kernel.org/patchwork/patch/1153625/ https://lore.kernel.org/patchwork/patch/1153626/ Compile-tested on: ipq40xx, lantiq Runtime-tested on: ipq40xx, lantiq Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.162Hauke Mehrtens2020-01-051-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ramips Runtime-tested on: ramips Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: generate firmware image for aircube-ispChristian Mauderer2019-12-311-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a "factory" image for the aircube-isp devices. Note that the firmware can't be uploaded without prior special preparation. For the most recent instructions on how to do that, visit the OpenWRT wiki page of the Ubiquiti airCube ISP for details: https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp Current procedure: With the original firmware 2.5.0 it is possible to upload and execute a script via the configuration. To do that download and unpack the original configuration, adapt uhttpd config to execute another lua handler (placed in the config directory) and pack and upload it again. The lua handler can call a script that mounts an overlayfs and modifies the "fwupdate.real" binary so that an unsigned image is accepted. The overlayfs is necessary because a security system (called tomoyo) doesn't allow binaries in other locations than /sbin/fwupdate.real (and maybe some more) to access the flash when executed via network. A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for finding out how to patch the binary so that it accepts an unsigned image. The current step-by-step procedure is: - Use a version 2.5.0 of the original firmware. This is important because a binary file will be modified. - Download a configuration. - Unpack it (it's just a tar gz file without an ending). - Add the following to uhttpd: `````` config 'uhttpd' 'other' list listen_http 0.0.0.0:8080 list listen_http [::]:8080 option 'home' '/tmp/persistent/config/patch/www' option lua_prefix '/lua' option lua_handler '/tmp/persistent/config/patch/handler.lua' `````` - Create a `patch` subfolder. - Create a `patch/www` subfolder. - Create a `patch/handler.lua` with the following content: `````` function handle_request(env) uhttpd.send("Status: 200 OK\r\n") uhttpd.send("Content-Type: text/plain\r\n\r\n") local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1" local proc = assert(io.popen(command)) for line in proc:lines() do uhttpd.send(line.."\r\n") end proc:close() end `````` - Create a `patch/patch.sh` with the following content: `````` #!/bin/sh -x set -e set -u set -x UBNTBOX_PATCHED="/tmp/fwupdate.real" MD5FILE="/tmp/patchmd5" cat <<EOF > ${MD5FILE} c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real EOF # check md5 of files that will be patched if ! md5sum -c ${MD5FILE} then echo "******** Error when checking files. Refuse to do anything. ********" exit 0 fi # prepare some overlay functionality LOWERDIR="/tmp/lower_root" mkdir -p ${LOWERDIR} mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR} overlay_some_path() { PATH_TO_OVERLAY=$1 ALIAS=$2 UPPERDIR="/tmp/over_${ALIAS}" WORKDIR="/tmp/over_${ALIAS}_work" mkdir -p ${UPPERDIR} mkdir -p ${WORKDIR} mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY} } # patch the ubntbox binary. overlay_some_path "/sbin" "sbin" echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598 echo "******** Done ********" `````` - Repack the configuration. - Upload it via the normal web interface. - Wait about a minute. The webserver should restart. - Now there is a second web server at port 8080 which can call the lua script. Visit the page with a web browser. Link is for example http://192.168.1.1:8080/lua - You should see the output of the script with a "*** Done ***" at the end. Note that the patches are not permanent. If you restart the router you have to re-visit the link (but not re-upload the config). - Now you can upload an unsigned binary via the normal web interface. Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
* ath79: tp-link: use ath10k-ct-smallbuffers for 64 MiB devicesPaul Fertser2019-12-251-5/+6
| | | | Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: use ath10k-ct-smallbuffers for 64 MiB devicesPaul Fertser2019-12-243-14/+14
| | | | Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: Do not build dlink_dir-615-e4 by defaultHauke Mehrtens2019-12-231-0/+1
| | | | | | | The factory image for the dlink_dir-615-e4 is getting too big which makes the full ath79 tiny build fail, deactivate it by default. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: fix MAC address setup for TP-Link TL-WDR3600/TL-WDR4300Sungbo Eo2019-12-212-1/+6
| | | | | | | | | | | | | | | | | | | | | | | The current ethernet MAC address setup of TL-WDR4300 board is different from the setup of stock firmware: OpenWrt: lan = label_mac -2, wan = label_mac -2 stock: lan = label_mac, wan = label_mac +1 The full address assignment is as follows: LAN label WAN label + 1 5G label 2G label - 1 This patch changes all devices using TL-WDR4300 board: TL-WDR3600 v1 (checked on device) TL-WDR4300 v1 (checked on device) TL-WDR4300 v1 (IL) Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rephrase/extend commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename ATH_SOC to SOCAdrian Schmutzler2019-12-208-174/+173
| | | | | | | This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: harmonize line breaks in image MakefilesAdrian Schmutzler2019-12-208-138/+187
| | | | | | | | | | | | | | | | This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79-tiny: enable 4k sectorsPaul Fertser2019-12-191-0/+1
| | | | | | | | | | | | | | | | This enables using 4kiB sectors as erase blocks for 4MiB NOR flash ICs that support it. Writeable jffs2 overlay used to store settings requires a partition with at least 5 erase blocks, so using small sectors is essential for devices with 4MiB flash. Sysupgrading a device running firmware without this feature will likely not allow to preserve configs automatically but since ath79 is considered to be in a "technology preview" state it shouldn't be a problem. Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: add D-Link DIR-615 E4Paul Fertser2019-12-195-0/+203
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - FCC ID: KA2IR615E3 - SoC: MIPS32 24K 400 MHz Atheros AR7240 - RAM: 32 MiB DDR SDRAM ESMT M13S2561616A-5T - Flash: 4 MiB NOR SPI Macronix MX25L3208E - Wireless: AR9287 2.4 GHz 802.11n 2T2R, 2x RP-SMA connectors - Ethernet: 5x 100BASE-TX Fast Ethernet - LEDs: 9x GPIO, 1x ath9k - Buttons: 2x tactile switches - UART: 3.3 V, 115200 8n1 - USB: simple hardware modification required, 1x USB 1.1 Full Speed Partitioning notes: Vendor firmware (based on CameoAP99) defines two additional partitions: "mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000. The "mac" partition stores LAN MAC address and hardware board name. However, the vendor firmware uses addresses from "nvram" partition, and the board name is used only for informational purposes in the Web interface (included in the pages' header), not affecting the firmware image check. The "lp" partition is supposed to contain a "language pack" (which can be used to add an additional language support to the Web interface) and is flashed separately, using the vendor firmware upgrade page. Since these partitions are absolutely useless for OpenWrt and overwriting them doesn't prevent downgrading to obsolete vendor firmware, this patch appends the valueable space to "firmware". Installation instructions: - Upgrade from OpenWrt ar71xx with "sysupgrade -f -n" or - Upload as a firmware update via the vendor Web-interface or - Connect UART and use "loady" to upload and run OpenWrt initramfs image, then sysupgrade from it (TFTP client doesn't work) or - Before powering up hold "reset" button and keep it pressed for about 15 seconds after, then access fail safe Web server on 192.168.0.1 (the old uIP TCP/IP protocol stack is not compatible with modern Linux, the kernel, so you'll need to use some other OS to do this). Can be performed without a Web-browser too: curl http://192.168.0.1/cgi/index \ -F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: enable all space on Netgear ar9344-based WNDR routersMichal Cieslakiewicz2019-12-191-5/+20
| | | | | | | | | | | Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash memory but only first 32 MiB are used now - both by vendor's firmware and OpenWrt. This patch concatenates two regions of flash memory: ubi part of firmware partition and reserved (unused) space beyond 'caldata_backup' while preserving ART backup. No data is wiped or moved away. This increases area for OS ubi volumes from 23 to 119 Megabytes. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: restore gpio-export on TL-WDR3600/4300Lech Perczak2019-12-191-30/+28
| | | | | | | | | | | | | | | | | | This partially reverts commit 32144ba275d163ce6e7d93546ab4414f03f508fb. This commit replaced gpio-exports in favor of gpio-hogs for enabling USB power at boot, but this rids the user of control of the USB port power present on this device for a long time. It was agreed on a mailing list [1] that this is not the way to go, and this patch breaks a very common use-case of WWAN modem reset by power cycle, used on a lot USB equipped routers, hence revert this change until a better solution can be found. [1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/020151.html Tested-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [adjusted commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR902AC v1Lech Perczak2019-12-196-2/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash OpenWrt (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. MAC Address summary: - wlan1 (2.4GHz Wi-Fi): Label MAC - wlan0 (5GHz Wi-Fi): Offset -1 from label - eth0 (Wired): Offset +1 from label Root access over serial line in vendor firmware: root/sohoadmin. Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [remove size-cells from gpio-export] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-09 15:11:05 +0000