aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: fix patching ath9k MAC address for MyNet WiFi Range ExtenderAdrian Schmutzler2019-10-211-1/+1
| | | | | | | | | | | | | | | | | The code line patching ath9k MAC address for this device contains a wrong number of arguments including an unset "$mac", which looks like a typo or copy/paste mistake. This has been introduced already in the device support commit 745dee11ac78 ("ath79: add support for WD My Net Wi-Fi Range Extender"). This patch just removes the "$mac" argument, leaving a formally valid line. (No on-device test has been performed.) Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Netgear WNR1000 v2Michal Cieslakiewicz2019-10-215-0/+218
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNR1000v2. Router was previously supported by ar71xx target only. Note: this is a 4_32 device with limited upgrade capabilities. Specification ============= * Description: Netgear WNR1000 v2 * Loader: U-boot * SOC: Atheros AR7240 (340 MHz) * RAM: 32 MiB * Flash: 4 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 3712 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9285) * USB: no * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_tiny=y CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr1000-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNR2000 v3Michal Cieslakiewicz2019-10-215-0/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNR2000v3. Router was previously supported by ar71xx target only. Note: this is a 4_32 device with limited upgrade capabilities. Specification ============= * Description: Netgear WNR2000 v3 * Loader: U-boot * SOC: Atheros AR7241 (360 MHz) * RAM: 32 MiB * Flash: 4 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 3712 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9287) * USB: no * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_tiny=y CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: WNR612v2: improve device supportMichal Cieslakiewicz2019-10-214-10/+19
| | | | | | | | | | | | | | | This patch improves ath79 support for Netgear WNR612v2. Router functionality becomes identical to ar71xx version. Changes include: * software control over LAN LEDs via sysfs * correct MAC addresses for network interfaces * correct image size in device definition * dts: 'keys' renamed to 'ath9k-keys' * dts: 'label-mac-device' set to eth1 (LAN) * dts: formatting adjustments Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add LAN LEDs control bits for AR724x GPIO function pinmuxMichal Cieslakiewicz2019-10-211-1/+9
| | | | | | | | | | | | | | | Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit. This patch adds new DTS settings to control LAN LEDs and CLKs that allow full software control over these diodes - exactly the same is done by ar71xx target in device setup phase for many routers (WNR2000v3 for example). 'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits. 'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and buttons on device. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Sitecom WLR-7100Tomasz Maciej Nowak2019-10-215-2/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless router. Specification SoC: Atheros AR1022 RAM: 64 MB DDR2 Flash: 8 MB SPI NOR WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R QCA9882 integrated (connected to PCIe lane) Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled, 5x switch Buttons: 2x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Toolbox > Firmware, 4. Browse for OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues 5GHz LED doesn't work Additional information When TX line on UART is connected, and board is switched on from power off state, the DDR memory training may fail. If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), which may or may not work with introduced images. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: fix gigabit link pll-data for EX7300Daniel Gimpelevich2019-10-211-2/+2
| | | | | | | | | | | | | The device did not appear to be reachable unless the connection were forced to 100Mb or lower. Revert to previously working pll-data. Also fix the phy-mode to represent the actual state needed for ethernet to function. Reported-by: Moritz Schreiber <moritz@mosos.de> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [add remark about phy-mode property] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add AR934x NAND Flash Controller driverMichal Cieslakiewicz2019-10-204-0/+1525
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch contains updated driver for Atheros NAND Flash Controller written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc'). ath79 version has adapted to work with kernel 4.19 and Device Tree. It has also been renamed to 'ar934x-nand' to avoid confusion with Near-Field Communication technology. Controller is present on Atheros AR934x SoCs and required for accessing internal flash storage on routers like Netgear WNDR4300. This port preserves all NAND programming code while moving platform configuration to Device Tree and replacing some kernel functions marked for retirement by 4.19. Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section). Most important changes to ar71xx version are: * old kernel sections of code removed * 'bool swap_dma' provided by platform data is now set by boolean DT property 'qca,nand-swap-dma' * board-supplied (mach-*.c code) platform data removed - its elements become either unused, redundant or replaced by DT methods (like reset) * IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore * calls to deprecated nand_scan_ident() + nand_scan_tail() function pair replaced by using recommended nand_scan() with attach_chip() callback * ECC is set to hardware by default, can be overriden by standard DT 'nand-ecc-*' properties (software Hamming or BCH are other options) This driver has been successfully tested on Netgear WNDR4300 running experimental ath79 OpenWrt master branch. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> [add reset control] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Clean up GL-AR300M DTS/DTSI inclusionsJeff Kletsky2019-10-202-4/+1
| | | | | | | | | | | | Modify GL-AR300M-Lite and GL-AR300M (NOR): * Include qca9531_glinet_gl-ar300m.dtsi directly rather than qca9531_glinet_gl-ar300m-nor.dts * Remove redundant inclusion of gpio.h and input.h Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use a single ath10k MAC patching function with checksumAdrian Schmutzler2019-10-151-22/+22
| | | | | | | | | | | | | | | | While all ath10k eeproms have a checksum field, so far two functions for patching ath10k MAC address have been present (and been used). This merges code to provide a single function ath10k_patch_mac in caldata.sh, having its name in accordance with ath9k functions. By doing so, correct MAC patching for current and future ath10k devices should be ensured. This patch adds checksum adjustments for several targets on ath79 and lantiq. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: correct ar71xx boardname for UniFi AC LiteDavid Bauer2019-10-151-1/+1
| | | | | | | | | This corrects the additional boardname for the image metadata to the one used in ar71xx. The previously present additional entry was never used on a running system. Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for UniFi AC-LRAndreas Ziegler2019-10-155-1/+19
| | | | | | | | | | | | | | The Unifi AC-LR has identical hardware to the Unifi AC-Lite. The antenna setup is different according to the vendor, which explains the thicker enclosure. Therefore, it is helpful to know the exact device variant, instead of having "Ubiquiti UniFi-AC-LITE/LR". Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [fix legacy name in commit message; add old boardname to SUPPORTED_DEVICES] Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: move MAC address patch functions to common libraryAdrian Schmutzler2019-10-142-77/+11
| | | | | | | | | This unifies MAC address patch functions and moves them to a common script. While those were implemented differently for different targets, they all seem to do the same. The number of different variants is significantly reduced by this patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move calibration data extraction function to libraryAdrian Schmutzler2019-10-132-122/+54
| | | | | | | | | | | | | | | | | This moves the almost identical calibration data extraction functions present multiple times in several targets to a single library file /lib/functions/caldata.sh. Functions are renamed with more generic names to merge different variants that only differ in their names. Most of the targets used find_mtd_chardev, while some used find_mtd_part inside the extraction code. To merge them, the more abundant version with find_mtd_chardev is used in the common code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [rebase on latest master; add mpc85xx] Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: move xor() from caldata extraction to functions.shAdrian Schmutzler2019-10-132-32/+1
| | | | | | | | The xor() function is defined in each of the caldata extraction scripts for several targets. Move it to functions.sh to reduce duplicate code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for COMFAST CF-E313ACRoger Pueyo Centelles2019-10-134-0/+174
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E313AC, an outdoor wireless CPE with two Ethernet ports and a 802.11ac radio. Specifications: - QCA9531 SoC - 650/400/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps WAN Ethernet, 48V PoE-in - 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out - 1x manual pass-through PoE switch - 64 MB RAM (DDR2) - 16 MB FLASH - QCA9886 2T2R 5 GHz 802.11ac, 23 dBm - 12 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. Alternatively, the U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The device's LEDs will blink several times and the recovery page will be at http://192.168.1.1; use it to upload the sysupgrade image. Note: Four MAC addresses are stored in the "art" partition (read-only): - 0x0000: 40:A5:EF:AA:AA:A0 - 0x0006: 40:A5:EF:AA:AA:A2 - 0x1002: 40:A5:EF:AA:AA:A1 - 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data) The stock firmware assigns MAC addresses to physical and virtual interfaces in a very particular way: - eth0 corresponds to the physical Ethernet port labeled as WAN - eth1 corresponds to the physical Ethernet port labeled as LAN - eth0 belongs to the bridge interface br-wan - eth1 belongs to the bridge interface br-lan - eth0 is assigned the MAC from 0x0 (*:A0) - eth1 is assigned the MAC from 0x1002 (*:A1) - br-wan is forced to use the MAC from 0x1002 (*:A1) - br-lan is forced to use the MAC from 0x0 (*:A0) - radio0 uses the calibration data from 0x5000 (which contains a valid MAC address, *:A3). However, it is overwritten by the one at 0x6 (*:A2) This commit preserves the LAN/WAN roles of the physical Ethernet ports (as labeled on the router) and the MAC addresses they expose by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position of the eth0/eth1 compared to the stock firmware: - eth0 corresponds to the physical Ethernet port labeled as LAN - eth1 corresponds to the physical Ethernet port labeled as WAN - eth0 belongs to the bridge interface br-lan - eth1 is the interface at @wan - eth0 is assigned the MAC from 0x0 (*:A0) - eth1 is assigned the MAC from 0x1002 (*:A1) - br-lan inherits the MAC from eth0 (*:A0) - @wan inherits the MAC from eth1 (*:A1) - radio0's MAC is overwritten to the one at 0x6 This way, eth0/eth1's positions differ from the stock firmware, but the weird MAC ressignations in br-lan/br-wan are avoided while the external behaviour of the router is maintained. Additionally, WAN port is connected to the PHY gmac, allowing to monitor the link status (e.g., to restart DHCP negotiation when plugging a cable). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* kernel: bump 4.14 to 4.14.147Koen Vandeputte2019-10-081-12/+10
| | | | | | | | | | | | | Refreshed all patches. Altered patches: - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx) - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79) Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: improve DTS for TP-Link Archer D50 v1Adrian Schmutzler2019-10-061-6/+10
| | | | | | | | | This addresses several issues in the DTS file: - add diag LED support - remove unused node names - fix whitespace issues Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix whitespace issues in DTS filesAdrian Schmutzler2019-10-0628-39/+2
| | | | | | | | | This is the result of grepping/searching for several common whitespace issues like double empty lines, leading spaces, etc. This patch fixes them for the ath79 target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-067-52/+52
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.19 to 4.19.76Koen Vandeputte2019-10-041-12/+10
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 403-mtd_fix_cfi_cmdset_0002_status_check.patch Compile-tested on: ath79, cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: Restore GL.iNet GL-AR300M-Lite first-boot connectivityJeff Kletsky2019-09-291-1/+5
| | | | | | | | | | | | | | | | | | The relationship between GMAC0 and GMAC1 and the kernel devices eth0 and eth1 was reversed for many ath79 devices by commit 8dde11d521 ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi The GL-AR300M-Lite is a single-port device, with the "LAN" port of the GL-AR300M board unpopulated and its sole port now referenced as eth1, as a result of commit 8dde11d521. The device was unreachable on first boot or fresh config. By changing &eth1 (GMAC1) to an MFD, GMAC0 is able to associate with the phy and is known by the kernel as "eth0". Thanks to Chuanhong Guo for the suggestion of "simple-mfd" Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: Correct glinet, gl-ar300m-lite in 02_networkJeff Kletsky2019-09-291-1/+1
| | | | | | | | | | | | | | Previously, the board name for the GL-AR300M-Lite was incorrect in 02_network, resulting in an unintended, fall-through condition when initializing the network configuration. While builds prior to commit 8dde11d521 (merged June 5, 2019) ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi functioned properly, the error was noted in resolving first-boot connectivity issues related to the single-phy nature of the device and the "swap" of eth0 and eth1 related to that commit. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* treewide: fix hex2dec conversion for MAC address checksum offsetAdrian Schmutzler2019-09-291-2/+2
| | | | | | | | | | | | | | | | If chksum_offset is converted by $(($...)) at the beginning, the check [ -n "$chksum_offset" ] will always return true, as the conversion yields "0" for an empty argument, and [ -n "0" ] is true. With this patch, the variable is not converted before the check, but only when it's used in dd. No conversion is done for use in hexdump, as this can deal with hex value offsets. Fixes: b133e466b08e ("treewide: convert WiFi caldata size and offset to hexadecimal") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove redundant ucidef_set_interfaces_* calls in 02_networkAdrian Schmutzler2019-09-251-2/+1
| | | | | | | | | | If already included in ucidef_add_switch, you do not have to additionally set the interface mode in ucidef_set_interfaces_* functions. This patch removes/adjusts such redundant cases. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 4.19 to 4.19.75Koen Vandeputte2019-09-241-2/+2
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: convert devices to interrupt-driven gpio-keysAdrian Schmutzler2019-09-2247-94/+51
| | | | | | | | | | | | | This converts all remaining devices to use interrupt-driven gpio-keys compatible instead of gpio-keys-polled. The poll-interval is removed. Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as this one is using ath9k keys. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Karl Palsson <karlp@etactica.com> Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add support of Netgear WNDR3800CHDmitry Tunin2019-09-214-3/+53
| | | | | | | | Add support for the ar71xx supported Netgear WNDR3800CH to ath79. The device is identical to WNDR3800 except NETGEAR_BOARD_ID. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: DIR825B1 switch to gpio-keysDmitry Tunin2019-09-211-4/+1
| | | | Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: remove invalid uses of ath9k_patch_fw_mac_crcAdrian Schmutzler2019-09-211-3/+3
| | | | | | | | | | | | Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which is meant to generate a checksum, for fixing their ath9k MAC addresses. However, those do not have a checksum field, and the calculated checksum offset would be negative. This patch will use ath9k_patch_fw_mac function for those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: image: pad kernel for Adtran/Bluesocket devicesTomasz Maciej Nowak2019-09-211-2/+2
| | | | | | | | | | | | | | | | It has been reported that using the sysupgrade-tar image will trigger "lzma_decode failed error". The RedBoot bootloader always loads data from flash till block size boundary, so if there's no padding it'll also load the beginning of rootfs, and it seems that lzma_decoder can't handle that garbage data. Previously the script creating combined-image silently padded the kernel and rootfs, but since sysupgrade-tar doesn't, pad the default kernel image. Fixes: 900330f ("ath79: image: retire combined-image for Adtran/Bluesocket devices") Cc: Brian Gonyer <bgonyer@gmail.com> Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: sort device definitions in image/*Adrian Schmutzler2019-09-216-303/+301
| | | | | | | | | | | This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add SUPPORTED_DEVICES to ubnt_nanostation-m-xwRoger Pueyo Centelles2019-09-191-1/+1
| | | | | | | | | | | | | | | | The ar71xx images for the Ubiquiti NanoStation M (XW) devices use "nanostation-m-xw" as the board name, but the ath79 images are only compatible with the "nano-m-xw" board name, so sysupgrade complains. By adding this additional supported device, sysuspgrade smoothly upgrades from ar71xx to ath79. Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb. Ref: https://github.com/openwrt/openwrt/pull/2418 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add XM device variant for Ubiquiti devicesAdrian Schmutzler2019-09-191-2/+2
| | | | | | | | | | So far, XW devices have DEVICE_VARIANT defined and XM devices have no DEVICE_VARIANT set. This adds DEVICE_VARIANT for XM devices, and moves definitions for both XM and XW to the common definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: provide label MAC addressAdrian Schmutzler2019-09-1954-12/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ath79. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - alfa-network,ap121f - avm,fritz300e - ubnt-xm devices For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - adtran,bsap1800-v2 - adtran,bsap1840 - dlink,dir-842-c1/-c2/-c3 - engenius,ecb1750 - iodata,etg3-r - iodata,wn-ac1167dgr - iodata,wn-ac1600dgr - iodata,wn-ac1600dgr2 - iodata,wn-ag300dgr - nec,wg800hp - nec,wg1200cr - trendnet,tew-823dru Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C59v2Keith Maika2019-09-165-1/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath79 support for Archer C59v2, previously supported by ar71xx. TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* ath79: move common definitions from Archer C58/C59 to common DTSIAdrian Schmutzler2019-09-163-143/+74
| | | | | | | | | The Archer C58/C59 have redundant LED and MAC address definitions in their DTS files. This moves them to the parent DTSI file. The patch already accounts for the upcoming Archer C59 v2. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: eg200: enable status led usageKarl Palsson2019-09-152-2/+4
| | | | | | | | | This enables using the "eTactica" LED during boot, to indicate failsafe, and during upgrade, while still leaving the LED alone for normal operation. This brings the device more in line with how other devices work, and makes the failsafe functionality easier to use and understand. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: fix UniFi AC LED mappingDavid Bauer2019-09-121-4/+9
| | | | | | | | | | | The UniFi AC LED mapping is currently off. The blue/white LED are used as WiFi indicators, while the vendor firmware does not feature WiFI LEDs. Instead, the LEDs are used to indicate the devices status. Align the LED mapping to match the vendor firmware as good as possible. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: sysupgrade: use $UPGRADE_BACKUP to check for backupRafał Miłecki2019-09-111-2/+2
| | | | | | | Now that $UPGRADE_BACKUP is set conditionally there is no need to check the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-051-2/+2
| | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: fix invalid UPGRADE_OPT_SAVE_CONFIG spellingsRafał Miłecki2019-09-051-2/+2
| | | | | | | That was a result of accidentally running "sed" twice on some files. Fixes: 5797fe84a3b5 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: replace remaining (not working now) $SAVE_CONFIG usesRafał Miłecki2019-09-051-2/+2
| | | | | | | This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG Fixes: b534ba961100 ("base-files: pass "save_config" option to the "sysupgrade" method") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: add support for TP-Link WDR3500 v1Adrian Schmutzler2019-09-036-131/+238
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: AR9344 CPU: 560 MHz Flash: 8 MiB RAM: 128 MiB WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9300 5GHz 802.11an Ethernet: AR934X built-in switch, WAN on separate physical interface USB: 1x 2.0 Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wdr3500v1_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [removed stray newline] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: image: disable sysupgrade images for routerstations and ja76pf2Tomasz Maciej Nowak2019-09-012-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Because a bug in handling partial erase blocks in 4.19 kernel, using sysupgrade images will hard brick devices that use RedBoot bootloader and have "FIS directory" with "RedBoot config" on the same erase block. Since flashing the devices from bootloader is safe, and to not cause a situation where external chip programmer or JTAG is needed, disable sysupgrade images for affected boards while creating kernel.bin and rootfs.bin for jjPlus JA76PF2 board, which doesn't have factory image. To set up the JA76PF2 board follow "Installation" instructions in b3a0c97 ("ath79: add support for jjPlus JA76PF2") except the part of loading initramfs image and using sysupgrade image for flashing (point 6 and 7). Enter following commands to flash the board from bootloader: fis init load -r -b 0x80060000 <openwrt_kernel_image_name> fis create linux load -r -b %{FREEMEMLO} <openwrt_rootfs_image_name> fis create rootfs fis load -l linux exec -c "" For RouterStations use TFTP recovery procedure. Ref: FS#2428 Cc: Matt Merhar <mattmerhar@protonmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: fix FIS partition detection for 4.19 kernelTomasz Maciej Nowak2019-09-011-0/+44
| | | | | | | | | When bumping to 4.19 the patch responsible for scaning flash for FIS partition got left out. Without it devices with RedBoot bootloader using automatic partitions detection in dts won't boot with the new kernel. Fixes: 3771176 ("ath79: add support for linux 4.19") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: image: add supported string for routerstations and ja76pf2Tomasz Maciej Nowak2019-09-012-0/+3
| | | | | | | | | Now that the md5 check is fixed and metadata present, sysupgrade on ar71xx will complain about device not being supported by the image. Since the cause is not matching strings for supported devices add them accordingly. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: image: append metadata to routerstations and ja76pf2 imagesTomasz Maciej Nowak2019-09-012-2/+2
| | | | | | | | This target enforces metadata check so add the necessary information. It was previously removed because md5 sum check. When using these sysupgrade images on ar71xx target the check would complain about them not matching. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: image: retire combined-image for Adtran/Bluesocket devicesTomasz Maciej Nowak2019-09-011-1/+1
| | | | | | | | | | | | During review it slipped by that these devices use combined-image which should never be used for newly added ones. Therefore switch to sysupgrade-tar generated images introduced in 8f6f260 ("ath79: routerstation: prepare to use sysupgrade-tar format image"). The sysupgrade accepts both images for now so no reression should occur. Cc: Brian Gonyer <bgonyer@gmail.com> Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: dts: fix ja76pf2 spi frequencyTomasz Maciej Nowak2019-09-011-1/+1
| | | | | | | | | | | The frequency was filled acording the information from datasheet for particular chip (Winbond 25Q128BVFG). Unfortunately this led to coruption and introduced bad blocks on the chip. Reducing the frequency to commonly used in ath79, made the board more stable and no new bad blocks were spoted. Fixes: b3a0c97 ("ath79: add support for jjPlus JA76PF2") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-11 14:16:54 +0000