aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: convert Winchannel WB2000 WiFis to nvmem-cellsNick Hainke2022-12-152-20/+26
| | | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (removed mtd-cal-data property, merged art + addr nodes back into partition) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert Ubiquiti UniFi AP Pro WiFis to nvmem-cellsNick Hainke2022-12-152-14/+21
| | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (merged art node back into partition-node) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert OCEDO Raccoon WiFis to nvmem-cellsNick Hainke2022-12-152-27/+30
| | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (merged art into partition node, removed stale uboot label) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: Mercury MW4530R v1 already uses nvmem-cellsNick Hainke2022-12-151-1/+0
| | | | | | | | Remove the caldata extraction in userspace. The board already uses nvmem-cells since commit e354b01baf88 ("ath79: calibrate all ar9344 tl-WDRxxxx with nvmem") Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: convert boards based on senao_ap-dual.dtsi WiFis to nvmem-cellsNick Hainke2022-12-156-21/+51
| | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: convert Atheros DB120 WiFis to nvmem-cellsNick Hainke2022-12-152-18/+25
| | | | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org> (merged art-node back into partition-node) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert Araknis AN-300-AP-I-N WiFis to nvmem-cellsNick Hainke2022-12-152-8/+12
| | | | | | | Pull the calibration data from the nvmem subsystem. This allows us to move userspace caldata extraction into the device-tree definition. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: add support for TP-Link CPE605-v1Andrew Cameron2022-12-134-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 23dBi high-gain directional antenna and a dedicated metal reflector - Power, LAN, WLAN5G green LEDs - 3x green RSSI LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* kernel: bump 5.10 to 5.10.157John Audia2022-12-111-1/+1
| | | | | | | | | | | | | | | Manually rebased: backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch Removed upstreamed: pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.81John Audia2022-12-111-1/+1
| | | | | | | | | | | | | | | | | | | | Manually rebased: backport-5.15/715-v6.0-net-ethernet-mtk_eth_soc-add-the-capability-to-run-m.patch hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch[1] Removed upstreamed: pending-5.15/701-netfilter-nf_flow_table-add-missing-locking.patch[2] All other patches automatically rebased 1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk> 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: fix Teltonika RUT230 v1 MAC assignmentDavid Bauer2022-12-091-2/+2
| | | | | | | | | The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi MAC is printed on the case as part of the SSID, however only the LAN MAC-Address is designated as a MAC-Address. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: optimize the firmware recipe for Netgear NAND devicesShiji Yang2022-12-061-11/+7
| | | | | | | | | | | | | | 1. Drop useless character '0xff' before fake filesystem header. 2. Reduce useless padding to shrink the size of the sysupgrade image. 3. Do not check the size of sysupgrade image. It does not make sense to check the size of a compressed package. 4. Do not take the size of netgear header into account because it will not be written to Flash. 5. Use the default lzma compression dictionary parameter '-d24' to get better performance. Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert Netgear R6100 radio calibration to nvmem-cellsShiji Yang2022-12-062-6/+12
| | | | | | | | use nvmem-cells implementation to avoid copying art calibration data to rootfs. Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: D-Link DIR-825 B1 add factory.bin recipeWill Moss2022-11-271-4/+6
| | | | | | | | | | - Bring back factory.bin image which was missing after porting device to ath79 target - Use default sysupgrade.bin image recipe - Adjust max image size according to new firmware partition size after "ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes - Remove support of upgrading from version 19.07, because partition size changes mentioned above Signed-off-by: Will Moss <willormos@gmail.com>
* ath79: add support for Senao Engenius EAP1750HMichael Pratt2022-11-274-0/+133
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: A8J-EAP1750H Engenius EAP1750H is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ **Specification:** - QCA9558 SOC - QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16FG - UART at J10 populated - 4 internal antenna plates (5 dbi, omni-directional) - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset) **MAC addresses:** MAC addresses are labeled as ETH, 2.4G, and 5GHz Only one Vendor MAC address in flash eth0 ETH *:fb art 0x0 phy1 2.4G *:fc --- phy0 5GHz *:fd --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** 2 ways to flash factory.bin from OEM: Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware Upgrade" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs to 'vmlinux-art-ramdisk' make available on TFTP server at 192.168.1.101 power board, interrupt boot execute tftpboot and bootm 0x81000000 NOTE: TFTP is not reliable due to bugged bootloader set MTU to 600 and try many times if your TFTP server supports setting block size higher block size is better. **Format of OEM firmware image:** The OEM software of EAP1750H is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin openwrt-ar71xx-generic-eap1750h-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. Newer EnGenius software requires more checks but their script includes a way to skip them, otherwise the tar must include a text file with the version and md5sums in a deprecated format. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: use nvmem-cells for radio calibration of EAP1200HMichael Pratt2022-11-273-7/+19
| | | | | | Transition from userscript to DTS for all of ART. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: calibrate TP-LINK TL-WR2543ND with nvmemEdward Chow2022-11-272-5/+13
| | | | | | | | | | | | | | | | | Driver for and pci wlan card now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. The wifi mac address remains correct after these changes, because When both "mac-address" and "calibration" are defined, the effective mac address comes from the cell corresponding to "mac-address" and mac-address-increment. Test passed on my tplink tl-wr2543nd. Signed-off-by: Edward Chow <equu@openmail.cc>
* kernel: bump 5.10 to 5.10.156John Audia2022-11-271-7/+7
| | | | | | | | Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch All other patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.80John Audia2022-11-271-7/+7
| | | | | | | | | | | | | | Manually rebase: pending-5.15/330-MIPS-kexec-Accept-command-line-parameters-from-users.patch ath79/patches-5.15/910-unaligned_access_hacks.patch All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: fix MAC address assigment for TP-Link TL-WR740N/TL-WR741ND v4Will Moss2022-11-201-3/+2
| | | | | | | On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main device MAC address, so do not increment it. WAN MAC is LAN MAC + 1. Signed-off-by: Will Moss <willormos@gmail.com>
* ath79: disable image building for Ubiquiti EdgeSwitch 8XPRoger Pueyo Centelles2022-11-201-0/+1
| | | | | | | | | | The downstream OpenWrt driver for the BCM53128 switch ceased to work, rendering the 8 LAN ports of the device unusable. This commit disables image building while the problem is being solved. See issue #10374 for more details. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: calibrate nand netgear wndrxxxx with nvmemEdward Chow2022-11-203-35/+24
| | | | | | | | | | | | | | | | | | | Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. wmac's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. The wifi mac address remains correct after these changes, because When both "mac-address" and "calibration" are defined, the effective mac address comes from the cell corresponding to "mac-address" and mac-address-increment. Test passed on my wndr3700v4 and wndr4500v3. Signed-off-by: Edward Chow <equu@openmail.cc>
* ath79: calibrate all ar9344 tl-WDRxxxx with nvmemEdward Chow2022-11-184-41/+27
| | | | | | | | | | | | | | | | | | | | Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. wmac's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. The wifi mac address remains correct after these changes, because When both "mac-address" and "calibration" are defined, the effective mac address comes from the cell corresponding to "mac-address" and mac-address-increment. Test passed on my tplink tl-wdr4310. Signed-off-by: Edward Chow <equu@openmail.cc>
* treewide: uniform vendor name for devoloMoritz Warning2022-11-181-2/+2
| | | | | | | The company name is lower case on the website (https://www.devolo.de) and in product names. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* ath79: support Ruckus ZoneFlex 7025Lech Perczak2022-11-134-3/+225
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise access point with built-in Ethernet switch, in an electrical outlet form factor. Hardware highligts: - CPU: Atheros AR7240 SoC at 400 MHz - RAM: 64MB DDR2 - Flash: 16MB SPI-NOR - Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio - Ethernet: single Fast Ethernet port inside the electrical enclosure, coupled with internal LSA connector for direct wiring, four external Fast Ethernet ports on the lower side of the device. - PoE: 802.3af PD input inside the electrical box. 802.3af PSE output on the LAN4 port, capable of sourcing class 0 or class 2 devices, depending on power supply capacity. - External 8P8C pass-through connectors on the back and right side of the device - Standalone 48V power input on the side, through 2/1mm micro DC barrel jack Serial console: 115200-8-N-1 on internal JP1 header. Pinout: ---------- JP1 |5|4|3|2|1| ---------- Pin 1 is near the "H1" marking. 1 - RX 2 - n/c 3 - VCC (3.3V) 4 - GND 5 - TX Installation: There are two methods of installation: - Using serial console [1] - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw, but with much less manual steps, and is generally recommended, being safer. - Using stock firmware root shell exploit, SSH and TFTP [2]. Does not work on some rare versions of stock firmware. A more involved, and requires installing `mkenvimage` from u-boot-tools package if you choose to rebuild your own environment, but can be used without disassembly or removal from installation point, if you have the credentials. If for some reason, size of your sysupgrade image exceeds 13312kB, proceed with method [1]. For official images this is not likely to happen ever. [1] Using serial console: 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0x9f040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin [2] Using stock root shell: 0. Reset the device to factory defaullts. Power-on the device and after it boots, hold the reset button near Ethernet connectors for 5 seconds. 1. Connect the device to the network. It will acquire address over DHCP, so either find its address using list of DHCP leases by looking for label MAC address, or try finding it by scanning for SSH port: $ nmap 10.42.0.0/24 -p22 From now on, we assume your computer has address 10.42.0.1 and the device has address 10.42.0.254. 2. Set up a TFTP server on your computer. We assume that TFTP server root is at /srv/tftp. 3. Obtain root shell. Connect to the device over SSH. The SSHD ond the frmware is pretty ancient and requires enabling HMAC-MD5. $ ssh 10.42.0.254 \ -o UserKnownHostsFile=/dev/null \ -o StrictHostKeyCheking=no \ -o MACs=hmac-md5 Login. User is "super", password is "sp-admin". Now execute a hidden command: Ruckus It is case-sensitive. Copy and paste the following string, including quotes. There will be no output on the console for that. ";/bin/sh;" Hit "enter". The AP will respond with: grrrr OK Now execute another hidden command: !v54! At "What's your chow?" prompt just hit "enter". Congratulations, you should now be dropped to Busybox shell with root permissions. 4. Optional, but highly recommended: backup the flash contents before installation. At your PC ensure the device can write the firmware over TFTP: $ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin $ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin Locate partitions for primary and secondary firmware image. NEVER blindly copy over MTD nodes, because MTD indices change depending on the currently active firmware, and all partitions are writable! # grep rcks_wlan /proc/mtd Copy over both images using TFTP, this will be useful in case you'd like to return to stock FW in future. Make sure to backup both, as OpenWrt uses bot firmwre partitions for storage! # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1 # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1 When the command finishes, copy over the dump to a safe place for storage. $ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/ 5. Ensure the system is running from the BACKUP image, i.e. from rcks_wlan.bkup partition or "image 2". Otherwise the installation WILL fail, and you will need to access mtd0 device to write image which risks overwriting the bootloader, and so is not covered here and not supported. Switching to backup firmware can be achieved by executing a few consecutive reboots of the device, or by updating the stock firmware. The system will boot from the image it was not running from previously. Stock firmware available to update was conveniently dumped in point 4 :-) 6. Prepare U-boot environment image. Install u-boot-tools package. Alternatively, if you build your own images, OpenWrt provides mkenvimage in host staging directory as well. It is recommended to extract environment from the device, and modify it, rather then relying on defaults: $ sudo touch /srv/tftp/u-boot-env.bin $ sudo chmod 666 /srv/tftp/u-boot-env.bin On the device, find the MTD partition on which environment resides. Beware, it may change depending on currently active firmware image! # grep u-boot-env /proc/mtd Now, copy over the partition # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1 Store the stock environment in a safe place: $ cp /srv/tftp/u-boot-env.bin ~/ Extract the values from the dump: $ strings u-boot-env.bin | tee u-boot-env.txt Now clean up the debris at the end of output, you should end up with each variable defined once. After that, set the bootcmd variable like this: bootcmd=bootm 0x9f040000 You should end up with something like this: bootcmd=bootm 0x9f040000 bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init baudrate=115200 ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env) mtdids=nor0=ar7100-nor0 bootdelay=2 filesize=52e000 fileaddr=81000000 ethact=eth0 stdin=serial stdout=serial stderr=serial partition=nor0,0 mtddevnum=0 mtddevname=u-boot ipaddr=192.168.0.1 serverip=192.168.0.2 stderr=serial ethact=eth0 These are the defaults, you can use most likely just this as input to mkenvimage. Now, create environment image and copy it over to TFTP root: $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt $ sudo cp u-boot-env.bin /srv/tftp This is the same image, gzipped and base64-encoded: H4sICOLMEGMAA3UtYm9vdC1lbnYtbmV3LmJpbgDt0E1u00AUAGDfgm2XDUrTsUV/pTkFSxZoEk+o lcQJtlNaLsURwU4FikDiBN+3eDNvLL/3Zt5/+vFuud8Pq10dp3V3EV4e1uFDGBXTQeq+9HG1b/v9 NsdheP0Y5mV5U4Vw0Y1f1/3wesix/3pM/dO6v2jaZojX/bJpr6dtsUzHuktDjm//FHl4SnXdxfAS wmN4SWkMy+UYVqsx1PUYci52Q31I3dDHP5vU3ZUhXLX7LjxWN7eby+PVNNxsflfe3m8uu9Wm//xt m9rFLjXtv6fLzfEwm5fVfdhc1mlI6342Pytzldvn2dS1qfs49Tjvd3qFOm/Ta6yKdbPNffM9x5sq Ty805acL3Zfh5HTD1RDHJRT9WLGNfe6atJ2S/XE4y3LX/c6mSzZDs29P3edhmqXOz+1xF//s0y7H t3GL5nDqWT5Ui/Gii7Aoi7HQ81jrcHZY/dXkfLLiJwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAD8 xy8jb4zOAAAEAA== 7. Perform actual installation. Copy over OpenWrt sysupgrade image to TFTP root: $ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp Now load both to the device over TFTP: # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1 # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1 Verify checksums of both images to ensure the transfer over TFTP was completed: # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin And compare it against source images: $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin Locate MTD partition of the primary image: # grep rcks_wlan.main /proc/mtd Now, write the images in place. Write U-boot environment last, so unit still can boot from backup image, should power failure occur during this. Replace MTD placeholders with real MTD nodes: # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd> # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd> Finally, reboot the device. The device should directly boot into OpenWrt. Look for the characteristic power LED blinking pattern. # reboot -f After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Boot into OpenWrt initramfs as for initial installation. To do that without disassembly, you can write an initramfs image to the device using 'sysupgrade -F' first. 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Concatenate the firmware backups, if you took them during installation using method 2: $ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin 3. Write factory images downloaded from manufacturer website into fwconcat0 and fwconcat1 MTD partitions, or restore backup you took before installation: # mtd write ruckus_zf7025_backup.bin /dev/mtd1 4. Reboot the system, it should load into factory firmware again. Quirks and known issues: - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. - The 2.4 GHz radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: fix MAC address assignment for TP-Link ar7241 devicesWill Moss2022-11-121-4/+3
| | | | | | | | | On TP-Link ar7241 devices LAN and WAN interfaces are swapped. Keeping that in mind fix MAC address assignment as used in vendor firmware: LAN MAC - main MAC stored in u-boot and printed on label WAN MAC - LAN MAC + 1 Signed-off-by: Will Moss <willormos@gmail.com>
* ath79: move usb led trigger node to SoC dtsiShiji Yang2022-11-1272-550/+98
| | | | | | | These frequently used usb led triggers are universal. They should be moved to SoC dtsi. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: add support for Teltonika RUT300Daniel Golle2022-11-104-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | Add support for the Teltonika RUT300 rugged industrial Ethernet router Hardware -------- SoC: Qualcomm Atheros QCA9531 RAM: 64M DDR2 (EtronTech EM68B16CWQK-25IH) FLASH: 16M SPI-NOR (Winbond W25Q128) ETH: 4x 100M LAN (QCA9533 internal AR8229 switch, eth0) 1x 100M WAN (QCA9533 internal PHY, eth1) UART: 115200 8n1, same debug port as other Teltonika devices USB: 1 single USB 2.0 host port BUTTON: Reset LED: 1x green power LED (always on) 5x yellow Ethernet port LED (controlled by Linux) WAN port LED is used as boot status and upgrade indicator as the power LED cannot be controlled in software. Use the *-factory.bin file to intially flash the device using the vendor firmware's Web-UI. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: calibrate TL-WDR4900 v2 with nvmem-cellsEdward Chow2022-11-092-17/+24
| | | | | | | | | | | | | Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. wmac's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. Signed-off-by: Edward Chow <equu@openmail.cc>
* ath79: add missing clock name strings in SoC dtsiShiji Yang2022-11-095-5/+14
| | | | | | | For all SoC in the ath79 target, the PLL controller provides 3 main clocks "cpu", "ddr" and "ahb" through the input clock "ref". Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: move reference clock node to SoC dtsiShiji Yang2022-11-0925-186/+24
| | | | | | | AR7161, AR724x, AR9132 and QCA95xx only support fixed frequency external crystal oscillator, so move reference clock node to SoC dtsi files. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: backport support for "linux,rootfs" in DTRafał Miłecki2022-11-082-2/+2
| | | | | | | | | This DT property allows marking flash partition that Linux should use as a root device. It's useful for devices that don't use U-Boot and cmdline parser for partitioning. It may be used with "fixed-partitions" or some dynamic partitioning based on flash content. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: expand rootfs for DIR-825-B1 with unused spaceAlan Luck2022-11-061-6/+21
| | | | | | | | | | Expand currently unused flash space to roofs for DIR-825-B1 by using the same flash space as the old ar71xx big image without moving the caldata. With some testing this partition is use by the OEM firmware but if changed is regenerated which allows reverting to OEM firmware Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
* ath79: add support to TrendNet TEW-673GRUKorey Caro2022-11-064-4/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the TrendNet TEW-673GRU to ath79. This device was supported in 19.07.9 but was deprecated with ar71xx. This is mostly a copy of D-Link DIR-825 B1. Updates have been completed to enable factory.bin and sysupgrade.bin both. Code improvements to DTS file and makefile. Architecture | MIPS Vendor | Qualcomm Atheros bootloader | U-Boot System-On-Chip | AR7161 rev 2 (MIPS 24Kc V7.4) CPU/Speed | 24Kc V7.4 680 MHz Flash-Chip | Macronix MX25L6405D Flash size | 8192 KiB RAM Chip: | ProMOS V58C2256164SCI5 × 2 RAM size | 64 MiB Wireless | 2 x Atheros AR922X 2.4GHz/5.0GHz 802.11abgn Ethernet | RealTek RTL8366S Gigabit w/ port based vlan support USB | Yes 2 x 2.0 Initial Flashing Process: 1) Download 22.03 tew-673gru factory bin 2) Flash 22.03 using TrendNet GUI OpenWRT Upgrade Process 3) Download 22.03 tew-673gru sysupgrade.bin 4) Flash 22.03 using OpenWRT GUI Signed-off-by: Korey Caro <korey.caro@gmail.com>
* kernel: bump 5.15 to 5.15.77John Audia2022-11-051-1/+1
| | | | | | | | | | | | | | | | | Manually rebased: bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.153John Audia2022-11-051-1/+1
| | | | | | | | | | Manually rebased: bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch lantiq/patches-5.10/0028-NET-lantiq-various-etop-fixes.patch All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: add support for Linksys EA4500 v3Edward Chow2022-10-304-0/+238
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the Linksys EA4500 v3 wireless router Hardware -------- SoC: Qualcomm Atheros QCA9558 RAM: 128M DDR2 (Winbond W971GG6KB-25) FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00) WLAN: QCA9558 3T3R 802.11 bgn QCA9580 3T3R 802.11 an ETH: Qualcomm Atheros QCA8337 UART: 115200 8n1, same as ea4500 v2 USB: 1 single USB 2.0 host port BUTTON: Reset - WPS LED: 1x system-LED LEDs besides the ethernet ports are controlled by the ethernet switch MAC Address: use address(sample 1) source label 94:10:3e:xx:xx:6f caldata@cal_macaddr lan 94:10:3e:xx:xx:6f $label wan 94:10:3e:xx:xx:6f $label WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci Installation from Serial Console ------------ 1. Connect to the serial console. Power up the device and interrupt autoboot when prompted 2. Connect a TFTP server reachable at 192.168.1.0/24 (e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt initramfs image as "openwrt.bin" 3. To test OpenWrt only, go to step 4 and never execute step 5; To install, auto_recovery should be disabled first, and boot_part should be set to 1 if its current value is not. ath> setenv auto_recovery no ath> setenv boot_part 1 ath> saveenv 4. Boot the initramfs image using U-Boot ath> setenv serverip 192.168.1.66 ath> tftpboot 0x84000000 openwrt.bin ath> bootm 5. Copy the OpenWrt sysupgrade image to the device using scp and install it like a normal upgrade (with no need to keeping config since no config from "previous OpenWRT installation" could be kept at all) # sysupgrade -n /path/to/openwrt/sysupgrade.bin Note: Like many other routers produced by Linksys, it has a dual firmware flash layout, but because I do not know how to handle it, I decide to disable it for more usable space. (That is why the "auto_recovery" above should be disabled before installing OpenWRT.) If someone is interested in generating factory firmware image capable to flash from stock firmware, as well as restoring the dual firmware layout, commented-out layout for the original secondary partitions left in the device tree may be a useful hint. Installation from Web Interface ------------ 1. Login to the router via its web interface (default password: admin) 2. Find the firmware update interface under "Connectivity/Basic" 3. Choose the OpenWrt factory image and click "Start" 4. If the router still boots into the stock firmware, it means that the OpenWrt factory image has been installed to the secondary partitions and failed to boot (since OpenWrt on EA4500 v3 does not support dual boot yet), and the router switched back to the stock firmware on the primary partitions. You have to install a stock firmware (e.g. 3.1.6.172023, downloadable from https://www.linksys.com/support-article?articleNum=148385 ) first (to the secondary partitions) , and after that, install OpenWrt factory image (to the primary partitions). After successful installation of OpenWrt, auto_recovery will be automatically disabled and router will only boot from the primary partitions. Signed-off-by: Edward Chow <equu@openmail.cc>
* kernel: bump 5.15 to 5.15.75John Audia2022-10-301-2/+2
| | | | | | | | | | | | | | | | | | | | | Removed upstreamed: bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1] Manually rebased: patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch All other patches automatically rebased 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=2810061452f9b748b096ad023d318690ca519aa3 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.150John Audia2022-10-302-2/+2
| | | | | | | | | | | Manually rebased: bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> [Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: fix reference clock for RouterBoard 912UAGPavel Kamaev2022-10-231-1/+1
| | | | | | | | | | This fixes reference clock frequency of RB912. 25 MHz frequency leads to system clock running too fast, uptime incrementing too fast and delays (like `sleep 10`) returning too early. Board has quartz with NSK 3KHAA Z 40 000 marking. Signed-off-by: Pavel Kamaev <pavel@kamaev.me>
* kernel: move mac-address-ascii patches to genericChukun Pan2022-10-232-224/+0
| | | | | | | This enables other targets to use the mac-address-ascii feature. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ath79: refresh kernel patchesPetr Štetiar2022-10-202-2/+2
| | | | | | | | Refresh dirty patches after commit 711f1a8bcbdd ("kernel: mtd: backport SafeLoader parser"). Fixes: 711f1a8bcbdd ("kernel: mtd: backport SafeLoader parser") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: improve MAC address configuration of ELECOM devicesINAGAKI Hiroshi2022-10-191-1/+2
| | | | | | | | Get MAC address of WAN from HW.WAN.MAC.Address in hwconfig partition instead of calculated one from wlan's address. And added label_mac. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: use NVMEM for wlan caldata on ELECOM devicesINAGAKI Hiroshi2022-10-193-25/+39
| | | | | | | | Use NVMEM "calibration" implementation for ath9k/ath10k(-ct) on ELECOM WRC-300GHBK2-I and WRC-1750GHBK2-I/C instead of mtd-cal-data property or user-space script. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: use ARTIFACTS for initramfs-factory of ELECOM devicesINAGAKI Hiroshi2022-10-191-22/+12
| | | | | | | | | | Use ARTIFACTS to generate factory image of the following ELECOM devices instead of redundant recipe which generate on KERNEL_INITRAMFS. - ELECOM WRC-300GHBK2-I - ELECOM WRC-1750GHBK2-I/C Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: mtd: backport SafeLoader parserRafał Miłecki2022-10-192-0/+2
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.15 to 5.15.72John Audia2022-10-093-4/+4
| | | | | | | | | | | | | | | | | Removed upstreamed: generic/pending-5.15/722-net-mt7531-only-do-PLL-once-after-the-reset.patch[1] bcm53xx/patches-5.15/082-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[2] All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72 Run-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72 (RB5009UG+S+IN) 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=5de02ab84aeca765da0e4d8e999af35325ac67c2 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=ab5c5787ab5ecdc4a7ea20b4ef542579e1beb49d Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.147John Audia2022-10-091-1/+1
| | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/083-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.147&id=a8e6cde5062fb2aff81f86cc0770591714bee545 Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: fix model name of Extreme Networks WS-AP3805iTom Herbers2022-10-081-1/+1
| | | | | | | Everywhere else the device is referred to as WS-AP3805i, only the model name wrongly only said AP3805i. Signed-off-by: Tom Herbers <mail@tomherbers.de>
* ath79: increase max tx ring buffer for ag71xxRobert Meijer2022-10-061-1/+1
| | | | | | | | | | | | This allows the user to specify a larger tx ring buffer size via ethtool. Having symmetrical ring buffer sizes increases throughput on high bandwidth (1 gbps tested) network connections. The default value is not changed so the same behaviour is saved. Signed-off-by: Robert Meijer <robert.s.meijer@gmail.com> [ improve title, commit description and wrap to 80 columns ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 17:29:45 +0000