aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-062-2/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79/mikrotik: create shared device definitions for nor and nandAdrian Schmutzler2020-08-012-13/+19
| | | | | | | Move the image preparation and nand-utils package selection into common device definitions for NOR/NAND devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: cosmetic fixes for partition node of D-Link DIR-825 B1Adrian Schmutzler2020-07-301-1/+1
| | | | | | | Make the node name match the reg property and remove the unused DT label. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for gl-e750Luochongjun2020-07-294-1/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The gl-e750 is a portable travel router that gives you safe access to the internet while traveling. Specifications: - SoC: Qualcomm Atheros AR9531 (650MHz) - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG) - Ethernet: 10/100: 1xLAN - Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac) - USB: 1x USB 2.0 port - Switch: 1x switch - Button: 1x reset button - OLED Screen: 128*64 px MAC addresses based on vendor firmware: LAN *:a0 art 0x0 2.4GHz *:a1 art 0x1002 5GHz *:a2 art calculated from art 0x0 + 2 Flash firmware: Since openwrt's kernel already exceeds 2MB, upgrading from the official version of GL-inet (v3.100) using the sysupgrade command will break the kernel image. Users who are using version 3.100 can only upgrade via uboot. The official guidance for GL-inet is as follows: https://docs.gl-inet.com/en/3/troubleshooting/debrick/ In the future, GL-inet will modify the firmware to support the sysupgrade command, so users will be able to upgrade directly with the sysupgrade command in future releases. OLED screen control: OLED controller is connected to QCA9531 through serial port, and can send instructions to OLED controller directly through serial port. Refer to the links below for a list of supported instructions: https://github.com/gl-inet/GL-E750-MCU-instruction Signed-off-by: Luochongjun <luochongjun@gl-inet.com> [fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: disable default build for devices with 4M flashAdrian Schmutzler2020-07-291-0/+4
| | | | | | | | | | | | | | | It has been decided that the 19.07 release will be last one to include 4/32 devices. This disables default build for the remaining devices with 4M flash on ath79. Note that this will leave exactly one enabled device for ath79/tiny subtarget, PQI Air-Pen, which was moved there due to kernel size restrictions. All 4M TP-Link devices have already been disabled in 8819faff47ff ("ath79: do not build TP-Link tiny images by default") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: reorganize common image definitions for NetgearAdrian Schmutzler2020-07-293-26/+21
| | | | | | | | | | | | | Netgear currently has a special definition for tiny devices, which is only used by two devices. Despite, it sets ups the IMAGE/default definition individually for all devices, although there is actually only one exception. This merges the common parts into a single netgear_generic definition (in contrast to netgear_ath79_nand), and adjusts the individual definitions accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Compex WPJ563Leon M. George2020-07-263-2/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR 2 Gigabit ethernet ports 3×3 2.4GHz on-board radio miniPCIe slot that supports 5GHz radio PoE 24V passive or 36V-56V passive with optional IEEE 802.3af/at USB 3.0 header Installation: To install, either start tftp in bin/targets/ath79/generic/ and use the u-boot prompt over UART: tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj563-squashfs-sysupgrade.bin erase 0x9f680000 +1 erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize boot The cpximg file can be used with sysupgrade in the stock firmware (add SSH key in luci for root access) or with the built-in cpximg loader. The cpximg loader can be started either by holding the reset button during power up or by entering the u-boot prompt and entering 'cpximg'. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '7A02': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj563-squashfs-cpximg-7a02.bin MAC addresses: <&uboot 0x2e010> *:71 (label) <&uboot 0x2e018> *:72 <&uboot 0x2e020> *:73 <&uboot 0x2e028> *:74 Only the first two are used (for ethernet), the WiFi modules have separate (valid) addresses. The latter two addresses are not used. Signed-off-by: Leon M. George <leon@georgemail.eu>
* ath79: mikrotik: use base mac on lan for RBwAPG-5HacT2HnDBjoern Dobe2020-07-251-0/+4
| | | | | | | | | The Mikrotik RBwAPG-5HacT2HnD has only a single ethernet interface (lan), and the vendor uses the base (label) MAC address for it. Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> [commit title/message improvement] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: rename POWER_ON_STRIP registerSungbo Eo2020-07-2513-13/+13
| | | | | | | | | | AR8327 datasheet[1] calls the register at address 0x0010 "Power-on Strapping Register". As it has nothing to do with "strip", let's rename it to "POWER_ON_STRAP" to make it easier to grasp. [1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: re-enable image generation for GL-AR750SDavid Bauer2020-07-224-33/+23
| | | | | | | | | | | | | | | | The bootloader only writes the first 2MB of the image to the NOR flash when installing the NAND factory image. The bootloader is capable of booting larger kernels as it boots from the memory mapped SPI flash. Disable the NAND factory image. The NAND can be bootstrapped by writing the NAND initramfs image using the NOR upgrade method in the bootloader web-recovery and sysupgrading from there. The NOR variant is not affected. Also refactor the partition definitions in the DTS to make them less annoying to read. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: correctly define WiFi switch for TL-WR841ND v8Adrian Schmutzler2020-07-214-34/+51
| | | | | | | | | | | | | | | | | | | | | | | | The TL-WR841ND v8 feature a WiFi switch instead of a button. This adds the corresponding input-type to prevent booting into failsafe regularly. This has been defined correctly in ar71xx, but was overlooked when migrating to ath79. In contrast, the TL-WR842ND v2, which has the key set up as switch in ar71xx, actually has a button. The TL-MR3420 v2 has a button as well and is set up correctly for both targets. (Information based on TP-Link user guide) Note: While looking into this, I found that support PR for TL-MR3420 v2 switched reset button to ACTIVE_HIGH. However, the other two device still use ACTIVE_LOW. This seems strange, but I cannot verify it lacking the affected devices. Fixes: FS#2733 Fixes: 9601d94138de ("add support for TP-Link TL-WR841N/ND v8") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: harmonize model names for Ubiquiti devicesAdrian Schmutzler2020-07-1517-27/+26
| | | | | | | | | | | | | | | | | | | | This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBridge MVieno Hakkerinen2020-07-155-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti PowerBridge M, which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - Internal antenna: 25 dBi - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other Bullet M (XM) boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbridge-m-squashfs-factory.bin Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
* ath79: use rgmii-id instead of rgmii in ubnt,lap-120Roger Pueyo Centelles2020-07-131-3/+2
| | | | | | | | | | | Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init) the incoming incoming traffic on the ubnt,lap-120 devices Ethernet port was not making it through. Using rgmii-id instead of rgmii (same configuration as ubnt,litebeam-ac-gen2) fixes it. Fixes FS#2893. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: fix dsa binding for TP-Link TL-WR941ND v2Chuanhong Guo2020-07-122-13/+9
| | | | | | | | | upstream changed dt-bindings for marvell 88e6060 to use mdio-device and dropped support for legacy bindings. fix it in our local dts. Fixes: FS#2524 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qihoo,c301: use phy-supply for usb vbusChuanhong Guo2020-07-121-2/+2
| | | | | | | | Linux phy subsystem provides support for a phy regulator defined via phy-supply property. Use it to turn on usb power only when usb is probed. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: disable TP-Link TL-WR941ND v2Adrian Schmutzler2020-07-111-1/+1
| | | | | | | | | | | | | The support for this device's Marvell MV88E6060 switch has been reported to be broken with kernels 4.19/5.4 (see bug report). Since this a 4/32 device and it has been confirmed to be working with stable 19.07 release (kernel 4.14), and since fixing it does not seem trivial, let's just disable it in master. Fixes: FS#2524 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for D-Link DAP-1330/DAP-1365 A1Sebastian Schaper2020-07-098-3/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Port device support for DAP-1330 from the ar71xx target to ath79. Additionally, images are generated for the European through-socket case variant DAP-1365. Both devices run the same vendor firmware, the only difference being the DAP_SIGNATURE field in the factory header. The vendor's Web UI will display a model string stored in the flash. Specifications: * QCA9533, 8 MiB Flash, 64 MiB RAM * One Ethernet Port (10/100) * Wall-plug style case (DAP-1365 with additional socket) * LED bargraph RSSI indicator Installation: * Web UI: http://192.168.0.50 (or different address obtained via DHCP) There is no password set by default * Recovery Web UI: Keep reset button pressed during power-on until LED starts flashing red, upgrade via http://192.168.0.50 * Some modern browsers may have problems flashing via the Web UI, if this occurs consider booting to recovery mode and flashing via: curl -F \ files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \ http://192.168.0.50/cgi/index The device will use the same MAC address for both wired and wireless interfaces, however it is stored at two different locations in the flash. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: add support for Arduino YunSungbo Eo2020-07-086-0/+351
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Arduino Yun is a microcontroller development board, based on Atmel ATmega32u4 and Atheros AR9331. Specifications: - MCU: ATmega32U4 - SoC: AR9331 - RAM: DDR2 64MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: SoC internal - Ethernet: 1x 10/100Mbps - USB: 1x 2.0 - MicroSD: 1x SDHC Notes: - Stock firmware is based on OpenWrt AA. - The SoC UART can be accessed only through the MCU. YunSerialTerminal is recommended for access to serial console. - Stock firmware uses non-standard 250000 baudrate by default. - The MCU can be reprogrammed from the SoC with avrdude linuxgpio. Installation: 1. Update U-Boot environment variables to adapt to new partition scheme. > setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000" > setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro" > saveenv 2. Boot into stock firmware normally and perform sysupgrade with sysupgrade image. # sysupgrade -n -F /tmp/sysupgrade.bin Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: add support for D-Link DCH-G020 Rev. A1Sebastian Schaper2020-07-084-0/+207
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DCH-G020 is a Smart Home Gateway for Z-Wave devices. Specifications: * QCA9531, 16 MiB Flash, 64 MiB RAM * On-Board USB SD3503A Z-Wave dongle * GL850 USB 2.0 Hub (one rear port, internal Z-Wave) * Two Ethernet Ports (10/100) Installation: * Web UI: http://192.168.0.60 (or different address obtained via DHCP) Login with 'admin' and the 6-digit PIN Code from the bottom label * Recovery Web UI: Keep reset button pressed during power-on until LED starts flashing red, upgrade via http://192.168.0.60 * Some modern browsers may have problems flashing via the Web UI, if this occurs consider booting to recovery mode and flashing via: curl -F \ files=@openwrt-ath79-generic-dlink_dch-g020-a1-squashfs-factory.bin \ http://192.168.0.60/cgi/index Known issues: * Real-Time-Clock is not working as there is currently no matching driver It is still included in the dts as compatible = "pericom,pt7c43390"; * openzwave was tested on v19.07 (running MinOZW as a proof-of-concept), but the package grew too big as lots of device pictures were included, thus any use of Z-Wave is up to the user (e.g. extroot and domoticz) The device will use the same MAC address for both wired and wireless interfaces, however it is stored at two different locations in the flash. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: add support for 8devices Lima boardAndrey Bondar2020-07-083-3/+130
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: • 650/600/216 MHz (CPU/DDR/AHB) • 64 MB of RAM (DDR2) • 32 MB of FLASH • 2T2R 2.4 GHz • 2x 10/100 Mbps Ethernet • 1x USB 2.0 Host socket • 1x miniPCIe slot • UART for serial console • 14x GPIO Flash instructions: Upgrading from ar71xx target: • Upload image into the board: scp openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin root@192.168.1.1/tmp/ • Run sysupgrade sysupgrade -F /tmp/openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin Upgrading from u-boot: • Set up tftp server with openwrt-ath79-generic-8dev_lima-initramfs-kernel.bin • Go to u-boot (reboot and press ESC when prompted) • Set TFTP server IP setenv serverip 192.168.1.254 • Set device ip from the same subnet setenv ipaddr 192.168.1.1 • Copy new firmware to board tftpboot 0x82000000 initramfs.bin • Boot OpenWRT bootm 0x82000000 • Upload image openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin into the board • Run sysupgrade. Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
* ath79: nand: disable images for glinet_gl-ar750sPetr Štetiar2020-07-071-0/+2
| | | | | | | | | Fixes following build failures: WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for 8devices Rambutan boardAndrey Bondar2020-07-075-0/+151
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rambutan is a Wifi module based on QCA9550/9557 http://www.8devices.com/products/rambutan Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of DDR2 RAM - 128 MB of NAND Flash - 1x 100Mbps Ethernet - 1x 1000Mbps Ethernet (PHY on dev-kit) - 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz - 2x U.FL connectors on module, chip antennas on dev-kit - 1x miniPCIe slot - 2x USB2.0 host - 2x UART - SPI, I2C, GPIO Flash instructions: Upgrade from ar71xx target: sysupgrade -F /tmp/openwrt-ath79-nand-8dev_rambutan-squashfs-sysupgrade.tar or upgrade from GUI (don't save config) Use factory image to flash from U-Boot: tftpboot 80060000 openwrt-ath79-nand-8dev_rambutan-squashfs-factory.ubi nand erase.part ubi nand write 80060000 ubi ${filesize} Signed-off-by: Petr Štetiar <ynezz@true.cz> [copy&pasted missing commit description] Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
* ath79: switch to kernel 5.4David Bauer2020-07-071-1/+1
| | | | | | | | As the reported major bugs are ironed out, switch to the new kernel to begin testing with a broader audience. Signed-off-by: David Bauer <mail@david-bauer.net> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Update kernel 5.4 to version 5.4.50Hauke Mehrtens2020-07-042-2/+2
| | | | | | | Run tested: ath79, ipq40xx Build tested: ath79, ipq40xx Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Update kernel 4.19 to version 4.19.131Hauke Mehrtens2020-07-044-17/+11
| | | | | | | | | | | | | Fixes: - CVE-2020-10757 The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was backported which needed some adaptations to other code. Run tested: ath79 Build tested: ath79 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add support for GL.iNet GL-MiFiAntti Seppälä2020-07-034-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the ar71xx supported GL.iNet GL-MiFi to ath79. Specifications: - Atheros AR9331 - 64 MB of RAM - 16 MB of FLASH (SPI NOR) - 2x 10/100/1000 Mbps Ethernet - 2.4GHz (AR9330), 802.11b/g/n - 1x USB 2.0 (vbus driven by GPIO) - 4x LED, driven by GPIO - 1x button (reset) - 1x mini pci-e slot (vcc driven by GPIO) Flash instructions: Vendor software is based on openwrt so you can flash the sysupgrade image via the vendor GUI or using command line sysupgrade utility. Make sure to not save configuration over reflash as uci settings differ between versions. Note on MAC addresses: Even though the platform is capable to providing separate MAC addresses to the interfaces vendor firmware does not seem to take advantage of that. It appears that there is only single unique pre-programmed address in the art partition and vendor firmware uses that for every interface (eth0/eth1/wlan0). Similar behaviour has also been implemented in this patch. Note on GPIOs: In vendor firmware the gpio controlling mini pci-e slot is named 3gcontrol while it actually controls power supply to the entire mini pci-e slot. Therefore a more descriptive name (minipcie) was chosen. Also during development of this patch it became apparent that the polarity of the signal is actually active low rather than active high that can be found in vendor firmware. Acknowledgements: This patch is based on earlier work[1] done by Kyson Lok. Since the initial mailing-list submission the patch has been modified to comply with current openwrt naming schemes and dts conventions. [1] http://lists.openwrt.org/pipermail/openwrt-devel/2018-September/019576.html Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
* ath79: drop redundant status for gpio target-wideAdrian Schmutzler2020-07-0337-136/+0
| | | | | | | | All definitions of gpio in SoC DTSI files do not set status, i.e. have it enabled. This drops all remaining redundant "status = okay" definitions in descendent files (mostly older ones). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: enable gpio on ar933x by defaultAdrian Schmutzler2020-07-0316-60/+0
| | | | | | | | | | | All other SoC DTSI files have gpio enabled by default, only ar9330/ar9331 disable it by default, only to have it enabled again afterwards for each individual device. So, do not disable it in the first place, and drop all device-specific status statements afterwards. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Compex WPJ344Leon M. George2020-07-034-0/+180
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: AR9344 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR 2 Gigabit ethernet ports 2×2 2.4GHz on-board radio miniPCIe slot that supports 5GHz radio PoE 48V IEEE 802.3af/at - 24V passive optional USB 2.0 header Installation: To install, either start tftp in bin/targets/ath79/generic/ and use the u-boot prompt over UART: tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize erase 0x9f680000 +1 cp.b $fileaddr 0x9f030000 $filesize boot The cpximg file can be used with sysupgrade in the stock firmware (add SSH key in luci for root access) or with the built-in cpximg loader. The cpximg loader can be started either by holding the reset button during power up or by entering the u-boot prompt and entering 'cpximg'. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '6A08': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin MAC addresses: <&uboot 0x2e010> *:99 (label) <&uboot 0x2e018> *:9a <&uboot 0x2e020> *:9b <&uboot 0x2e028> *:9c Only the first two are used (for ethernet), the WiFi modules have separate (valid) addresses. The latter two addresses are not used. Signed-off-by: Leon M. George <leon@georgemail.eu> [minor commit message adjustments, drop gpio in DTS, DTS style fixes, sorting, drop unused cpximg recipe] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rearrange nand node by register addressSungbo Eo2020-07-022-36/+36
| | | | | | | All other nodes in the DTS are placed in order of address space. Harmonize the nand nodes as well. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: replace custom uImageArcher generationDavid Bauer2020-06-291-9/+1
| | | | | | | | | | | The replaces the custom uImageArcher build step with the generic uImage build step. The only different between these two is the difference in the generated name. Tested on: TP-Link Archer C59 v1 Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: do not build TP-Link tiny images by defaultAdrian Schmutzler2020-06-282-0/+3
| | | | | | | | | | | | | For quite some time, the tiny (4M flash) TP-Link sysupgrade and factory images cannot be built anymore by the buildbots, just the initramfs-kernel.bin files are still there. Disable these images for the buildbots and prevent useless builds. Note that these devices still build fine with default settings, even for kernel 5.4. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: build Compex WPJ531 cpximg filesLeon M. George2020-06-281-0/+28
| | | | | | | | | | | | | | | | | | | Generate additional images that are compatible to the cpximg loader. The cpximg loader can be started either by holding the reset button during power up or by entering the u-boot prompt and entering 'cpximg'. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '7A04': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin These files can also be used with the sysupgrade utility in stock images (add SSH key in luci for root access). Signed-off-by: Leon M. George <leon@georgemail.eu> [fix sorting of definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Compex WPJ531 (16M)Leon M. George2020-06-284-0/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9531 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR 2 100MBit ethernet ports 2×2 2.4GHz on-board radio miniPCIe slot that supports 5GHz radio PoE 24V - 48V IEEE 802.3af optional USB 2.0 header Installation: To install, start a tftp server in bin/targets/ath79/generic/ and use the u-boot prompt over UART: tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize erase 0x9f680000 +1 cp.b $fileaddr 0x9f030000 $filesize boot The cpximg file can be used with sysupgrade in the stock firmware (add SSH key in luci for root access). Another way is to hold the reset button during power up or running 'cpximg' in the u-boot prompt. Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '7A04': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin MAC addresses: <&uboot 0x2e010> *:cb (label) <&uboot 0x2e018> *:cc <&uboot 0x2e020> *:cd <&uboot 0x2e028> *:ce Only the first two are used (for ethernet), the WiFi modules have separate (valid) addresses. The latter two addresses are not used. Signed-off-by: Leon M. George <leon@georgemail.eu> [commit title/message facelift, fix rssileds, add led aliases] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Fix ubnt_edgeswitch-8xp DEVICE_PACKAGESHauke Mehrtens2020-06-271-1/+1
| | | | | | | | switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio instead. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: Tobias Schramm <tobleminer@gmail.com>
* ath79: drop and consolidate redundant chosen/bootargsAdrian Schmutzler2020-06-2568-262/+12
| | | | | | | | | | | | | | In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for AVM FRITZ!WLAN Repeater DVB-CNatalie Kagelmacher2020-06-257-4/+138
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C SOC: Qualcomm Atheros QCA9556 RAM: 64 MiB FLASH: 16 MB SPI-NOR WLAN: QCA9556 3T3R 2.4 GHZ b/g/n and QCA9880 3T3R 5 GHz n/ac ETH: Atheros AR8033 1000 Base-T DVB-C: EM28174 with MaxLinear MXL251 tuner BTN: WPS Button LED: Power, WLAN, TV, RSSI0-4 Tested and working: - Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s) - 2.4 GHz Wi-Fi (correct MAC) - 5 GHz Wi-Fi (correct MAC) - WPS Button (tested using wifitoggle) - LEDs - Installation via EVA bootloader (FTP recovery) - OpenWrt sysupgrade (both CLI and LuCI) - Download of "urlader" (mtd0) Not working: - Internal USB - DVB-C em28174+MxL251 (depends on internal USB) Installation via EVA bootloader (FTP recovery): Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device, connect to 192.168.178.1 through FTP and sign in with adam2/adam2: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Wait for "Transfer complete" together with the transfer details. Wait two minutes to make sure flash is complete (just to be safe). Then restart the device (power off and on) to boot into OpenWrt. Revert your NIC settings to reach OpenWrt at 192.168.1.1 Signed-off-by: Natalie Kagelmacher <nataliek@pm.me> [fixed sorting - removed change to other board - prettified commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: image: fix initramfs for safeloader devicesPetr Štetiar2020-06-221-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently it's not possible to tftpboot initramfs image on archer-c7-v5 as the image contains tplink-v1-header which leads to: ath> bootm ## Booting image at 81000000 ... Bad Magic Number as U-Boot expects uImage wrapped image. This is caused by following inheritance issue: define Device/Init KERNEL_INITRAMFS = $$(KERNEL) define Device/tplink-v1 KERNEL := kernel-bin | append-dtb | lzma KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header define Device/tplink-safeloader $(Device/tplink-v1) define Device/tplink-safeloader-uimage $(Device/tplink-safeloader) KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma define Device/tplink_archer-c7-v5 $(Device/tplink-safeloader-uimage) where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's then used by all devices inheriting from tplink-safeloader. Fix this by overriding KERNEL_INITRAMFS to KERNEL variable again. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: fix input type for TP-Link TL-WR902AC v1 mode switchLech Perczak2020-06-211-0/+2
| | | | | | | | | Inputs assigned to "mode select" switch on the side of the device were missing linux,input-type property. This would cause them do incorrectly generate EV_KEY events. Fix this by setting the linux,input-type = <EV_SW> property on them. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for TP-Link CPE610 v2Andrew Cameron2020-06-204-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G green LEDs - 3x green RSSI LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for TP-Link TL-WA801ND v3/v4Adrian Schmutzler2020-06-196-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This ports support for these devices from ar71xx. Specification: - System-On-Chip: Qualcomm Atheros QCA9533 - CPU/Speed: v3: 560 MHz, v4: 650 MHz - Flash: 4096 KiB - RAM: 32 MiB - Ethernet: 1 port @ 100M - Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn In contrast to the implementation in ar71xx (reset and WiFi button), the device actually features reset and WPS buttons. Flashing instructions: Upload the ...-factory.bin file via OEM web interface. TFTP Recovery: 1. Set PC to fixed IP address 192.168.0.66 2. Download *-factory.bin image and rename it to wa801ndv3_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. TFTP recovery has only been tested with v3, and the Wiki states that the procedure won't work for v4, which cannot be verified or falsified at the moment. Tested by Tim Ward (see forum): https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: set &eth1 status for TP-Link CPE devices in parent DTSIAdrian Schmutzler2020-06-184-6/+4
| | | | | | | The status is set to "okay" for all devices on ar9344, so just move this to the parent DTSI. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: define CONFIG_MFD_RB4XX_CPLD to fix build breakageHannu Nyman2020-06-172-0/+2
| | | | | | | | | | | | | | Define the kernel config symbol CONFIG_MFD_RB4XX_CPLD=n to fix build breakage on non-mikrotik targets. The driver was added for all ath79, but the symbol was only defined for mikrotik subtarget. Fixes: fa70b3a4bbc6 ("ath79: add Mikrotik rb4xx series drivers") Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [rearrange commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for the TP-Link WBS210 v1Adrian Schmutzler2020-06-165-0/+28
| | | | | | | | | | | | | | | | | | | | Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-165-8/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for MikroTik RouterBOARD 493G (rb4xx series)Christopher Hill2020-06-156-0/+258
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD RB493G, ported from the ar71xx target. See https://routerboard.com/RB493G for details Specification: - SoC Qualcomm Atheros AR7161 - RAM: 256 MiB - Storage: 128MiB NAND - Ethernet: 9x 1000/100/10 Mbps - USB 1x 2.0 / 1.0 type A - PCIe: 3x Mini slot - MicroSD slot Working: - Board/system detection - Ethernet - SPI - NAND - LEDs - USB - Sysupgrade Enabled (but untested due to lack of hardware): - PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed Installation methods: - tftp boot initramfs image, scp then flash via "sysupgrade -n" - nand boot existing OpenWrt, scp then flash via "sysupgrade -n" Notes: - initramfs image will not work if uncompressed image size over ~8.5Mb - The "rb4xx" drivers have been enabled Signed-off-by: Christopher Hill <ch6574@gmail.com>
* ath79: add Mikrotik rb4xx series driversChristopher Hill2020-06-156-0/+817
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds 3 Mikrotik rb4xx series drivers as follows: rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device that interfaces between the SoC SPI bus and its two children below. rb4xx-gpio: This is the GPIO expander. rb4xx-nand: This is the NAND driver. The history of this code comes in three phases. 1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/. Module-author: Gabor Juhos <juhosg@openwrt.org> Module-author: Imre Kaloz <kaloz@openwrt.org> Module-author: Bert Vermeulen <bert@biot.com> 2. Next several ar71xx patches were applied bringing the code current. commit 7bbf4117c6fe4b764d9d7c62fb2bcf6dd93bff2c Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> commit af79fdbe4af32a287798b579141204bda056b8aa commit 889272d92db689fd9c910243635e44c9d8323095 commit e21cb649a235180563363b8af5ba8296b9ac0baa commit 7c09fa4a7492ca436f2c94bd9a465b7c5bbeed6f Signed-off-by: Felix Fietkau <nbd@nbd.name> 3. Finally a heavy refactor to split the driver into the three new subsystems, and updated to work with the device tree configuration, plus updates and review feedback incorporated Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Christopher Hill <ch6574@gmail.com>
* ath79: ag71xx: don't warn on RGMII_RXID and RGMII_TXIDDavid Bauer2020-06-151-0/+4
| | | | | | | | | | Currently, ag71xx will trigger a warning when TX xor RX-Delay modes are enabled. Handle them identical to the already implemented RGMII modes, as they are only different for the attached PHY. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DAP-2695-A1Stijn Tintel2020-06-117-0/+235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: * SoC: Qualcomm Atheros QCA9558 * RAM: 256MB * Flash: 16MB SPI NOR * Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD) * WiFi 2.4GHz: Qualcomm Atheros QCA9558 * WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E * LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER * Buttons: 1x RESET * UART: 1x RJ45 RS-232 Console port Installation via stock firmware: * Install the factory image via the stock firmware web interface Installation via bootloader Emergency Web Server: * Connect your PC to the LAN1(PoE) port * Configure your PC with IP address 192.168.0.90 * Open a serial console to the Console port (115200,8n1) * Press "q" within 2s when "press 'q' to stop autoboot" appears * Open http://192.168.0.50 in a browser * Upload either the factory or the sysupgrade image * Once you see "write image into flash...OK,dest addr=0x9f070000" you can power-cycle the device. Ignore "checksum bad" messages. Setting the MAC addresses for the ethernet interfaces via /etc/board.d/02_network adds the following snippets to /etc/config/network: config device 'lan_eth0_1_dev' option name 'eth0.1' option macaddr 'xx:xx:xx:xx:xx:xx' config device 'wan_eth1_2_dev' option name 'eth1.2' option macaddr 'xx:xx:xx:xx:xx:xx' This would result in the proper MAC addresses being set for the VLAN subinterfaces, but the parent interfaces would still have a random MAC address. Using untagged VLANs could solve this, but would still leave those extra snippets in /etc/config/network, and then the device VLAN setup would differ from the one used in ar71xx. Therefore, the MAC addresses of the ethernet interfaces are being set via preinit instead. The bdcfg partition contains 4 MAC address labels: - lanmac - wanmac - wlanmac - wlanmac_a The first 3 all contain the same MAC address, which is also the one on the label. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 12:45:41 +0000