aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link Archer D50 V1Davide Fioravanti2019-05-185-0/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer D50 v1 is a dual-band AC1200 router + modem. The router section is based on Qualcomm/Atheros QCA9531 + QCA9882. The "DSL" section is based on BCM6318 but it's currently not supported. Internally eth0 is connected to the Broadcom CPU. Router section - Specification: CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB) RAM: 64 MB (DDR2) Flash: 8 MB (SPI NOR) Wifi 2.4GHz: QCA9531 2T2R Wifi 5GHz: QCA9982 2T2R 4x 10/100 Mbps Ethernet 8x LED, 3x button UART header on PCB Known issues: DSL not working (eth0) (WIP) UART connection --------------- J2 HEADER (Qualcomm CPU) . TX . RX . GND O VCC J16 HEADER (Broadcom CPU) O VCC . GND . RX . TX The following instructions require a connection to the J2 UART header. Flash instruction under U-Boot, using UART ------------------------------------------ 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Initramfs instruction under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin bootm 0x81000000 Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616 4. Double check the .mod file size. It must be 7995392 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed default-state = "off", it's already the default, added pcie node, fixed typo]
* ath79: add support for Aruba AP-105Chris Blake2019-05-183-0/+199
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Atheros AR7161-8C1A @ 680 MHz RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR) WI1: Atheros AR9223-AC1A 802.11bgn WI2: Atheros AR9220-AC1A 802.11an ETH: Atheros AR8021-BL1E + PoE LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G BTN: 1 x Reset I2C: AT97SC4303s TPM (needs driver!) CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud Factory installation: - Needs a u-boot replacement. See Wiki for information on how to do a in-circut flash with a SPI-Flasher like a CH314A or flashrom. Wiki page can be found at https://openwrt.org/toh/aruba/aruba_ap-105 - Be careful when dis- and reassembling the device to not squish any of the antenna cables in the process! - Be sure to make a full 16 MiB backup of your device before flashing the new u-boot! This is needed if you ever have interest in reverting back to stock firmware. Not working: - TPM (needs a driver) Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ath79: Add support for TP-Link TL-WR1043N v5Adrian Schmutzler2019-05-184-3/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - QCA9563 at 775 MHz - 64 MB RAM Zentel A3R12E40CBF-8E - 16 MB flash Winbond W25Q128FVSG - 3 (non-detachable) Antennas / 450 Mbit - 1x/4x WAN/LAN Gbps Ethernet (QCA8337) - reset and Wi-Fi buttons TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4, except that the USB port has been removed and there is no longer a removable antenna option. It also has different partitioning scheme. The software is more in line with the Archer series in that it uses a nested bootloader scheme. (This has been adapted from the OpenWrt Wiki page) <https://openwrt.org/toh/tp-link/tl-wr1043nd> Installation on HW rev.5: Factory firmware can be installed via the WEB interface. Alternatively, it is also possible to use a TFTP server for recovery purposes: - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin - Set static IP of your PC to *192.168.0.66* - Router will obtain IP 192.168.0.86 for a few seconds while loading, when reset button pressed at power On. And finally, there's always u-boot access through the UART. For information visit the wiki. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworked commit message]
* ath79: Move TL-WR1043ND v1 definition to companionsAdrian Schmutzler2019-05-181-10/+10
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Move settings specific for TP-Link TL-WR1043ND v4 to DTSAdrian Schmutzler2019-05-182-73/+70
| | | | | | This prepares for support of v5. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for EnGenius ECB1750sven friedmann2019-05-186-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - Qualcomm Atheros SoC QCA9558 - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 1x 10/100/1000 Mbps Ethernet - 3T3R 2.4 GHz (QCA9558 WMAC) - 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH) https://fccid.io/A8J-ECB1750 Tested and working: - lan, wireless, leds, sysupgrade (tftp) Flash instructions: 1.) tftp recovery - use a 1GbE switch or direct attached 1GbE link - setup client ip address 192.168.1.10 and start tftpd - save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory - plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed - afterwards login via ssh and do a sysuprade 2.) oem webinterface factory install (not tested) Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin". 3.) oem webinterface command injection OEM Firmware already running OpenWrt (Attitude Adjustment 12.09). Use OEM webinterface and command injection. See wiki for details. https://openwrt.org/toh/engenius/engenius_ecb1750_1 Signed-off-by: sven friedmann <sf.openwrt@okay.ms> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [use interrupt-driven "gpio-keys" binding]
* ath79: drop unused/incomplete dtsChuanhong Guo2019-05-173-230/+0
| | | | | | | | These dts itself are incomplete (e.g. missing mtd partitions) and its deivce support is never added to ath79 target. Drop these unused dts for now. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar9330: fix switch_led_disable_pins reg valuePetr Štetiar2019-05-171-1/+1
| | | | | | | | | | | | | | In commit e9652e1696d9 ("ath79: fix pinmux for ar933x devices") I've wrongly changed desired register value to 0xf8 although it should've been set to 0x0. 0xf8 value sets bits 3-7 (ETH_SWITCH_LEDx_EN) to 1 which actually enables ethernet switch LEDs, so 0x0 is correct value in order to use the pins as GPIO. Fixes: e9652e1696d9 ("ath79: fix pinmux for ar933x devices") Reported-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: archer-x7-v5: sync ar8327 initial reg values with ar71xxPetr Štetiar2019-05-171-2/+5
| | | | | | | | | Simply dumped content of this regs in ar71xx and wrote them to DTS, as a result port 6 on the switch will appear disconnected as on Archer C7v4. [AS: testing and PORT6_STATUS fix] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add missing reset button for TP-Link CPE210 v2 and v3Adrian Schmutzler2019-05-151-0/+10
| | | | | | | | Reset button support seems to be missing in ath79. Run-tested on CPE210 v2. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix pinmux for ar933x devicesPaul Wassi2019-05-155-3/+9
| | | | | | | | | | | | | Properly disable the SoC's internal Switch LEDs on the pinmux. Devices that previously called ath79_gpio_function_disable for the switch LEDs, just need to reference switch_led_pins in the pinctrl-0 property of the gpio-leds node. Signed-off-by: Paul Wassi <p.wassi@gmx.at> [changed desired pinctrl register value from 0x1f to proper 0xf8] Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [renamed pinmux name to switch_led_disable_pins to make purpose more clear] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: archer-x7-v5: remove confusing ar8327 initvals for LEDsPetr Štetiar2019-05-151-4/+0
| | | | | | | | This devices have LEDs connected to the SoC's GPIOs, so it makes no sense to fiddle with ar8327 LED regs. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.19 to 4.19.42Koen Vandeputte2019-05-131-1/+1
| | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch - 400-v5.2-leds-trigger-netdev-fix-refcnt-leak-on-interface-ren.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.118Koen Vandeputte2019-05-131-1/+1
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch Altered: - 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: Add missing read-only propertiesAdrian Schmutzler2019-05-118-2/+14
| | | | | | | | | Add some read-only properties to protect partitions from accidental changes. Also fixed two whitespaces error on the way. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: add a config option for enabling a testing version of the target kernelFelix Fietkau2019-05-111-0/+1
| | | | | | | If the target supports a newer kernel version that is not used by default yet, it can be enabled with this option Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: glinet_gl-ar750s: Use QCA9887 firmwareJeff Kletsky2019-05-051-1/+1
| | | | | | | The GL.iNet AR750S is based around the QCA9563 and requires the QCA9887 firmware for operation. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: fix OCEDO Raccoon 10Mbit PLL valueDavid Bauer2019-05-051-2/+1
| | | | | | | | | | | | This corrects the PLL value for 10 Mbit/s links on the OCEDO Raccoon. Prior to this patch, 10 Mbit/s links would not transmit data. It is worth mentioning that the vendor firmware used the same PLL settings and 10Mbit/s was also not working there. All other link-modes are working correctly without any packet loss. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.114Koen Vandeputte2019-05-021-2/+2
| | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 150-bridge_allow_receiption_on_disabled_port.patch - 201-extra_optimization.patch Remove upstreamed: - 022-0006-crypto-crypto4xx-properly-set-IV-after-de-and-encryp.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.35Koen Vandeputte2019-04-222-3/+3
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-3887 New symbol: - CONFIG_LDISC_AUTOLOAD Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.112Koen Vandeputte2019-04-222-3/+3
| | | | | | | | | | | | Refreshed all patches. New symbol: - CONFIG_LDISC_AUTOLOAD Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Revert "ath79: Add WPS button to TP-Link Archer C7v5"Petr Štetiar2019-04-141-7/+0
| | | | | | | Reverting this commit as I've missed the fact, that the button is already present in the included DTSI file. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove unnecessary packages from I-O DATA ETG3-RINAGAKI Hiroshi2019-04-131-0/+1
| | | | | | | | I-O DATA ETG3-R is a wired router. So wireless-related packages are unnecessary and remove those packages from default configuration to reduce flash usage. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add TP-Link WR842N v3Sven Roederer2019-04-134-1/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the TP-Link WR842N v3 which is already supported on ar71xx target (0b45bec22c59cc6e6b2fa71dc9a88386c5587132). Specification: * SoC: QCA9533 ver 2 rev 0 * 16 MB Flash (gd25q128) * 64 MB RAM * 1 WAN 10/100 MBit/s (blue connector) * 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors) * Atheros AR9531 (2,4GHz, two fixed antennas) * USB * Reset / WPS button * WiFi button (rf kill) * 8 green leds; 1 red/green led * serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed) Installation: * flash via vendor WebUI (the filename must not exceed certain length) * sysupgrade from installed OpenWrt (also ar71xx) Thanks to Holger Drefs for providing the hardware Tested-by: @kofec (github) Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ath79: add support for Netgear EX6400 and EX7300Daniel Gimpelevich2019-04-097-0/+280
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove more duplicate image build variablesDaniel Gimpelevich2019-04-093-22/+18
| | | | | | | | | Remove Netgear-specific image build variables which are set to the same value. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [reordering of variables, removed stray newline] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add WPS button to TP-Link Archer C7v5Petr Štetiar2019-04-081-0/+7
| | | | | | | This patch adds currently missing support for the WPS button on TP-Link Archer C7v5. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Correct MAC address for WAN interface of Archer A7/C7 v5Adrian Schmutzler2019-04-081-0/+5
| | | | | | | | | | | These devices share the network config with C7v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Fix GPIO reset button on TP-Link Archer C7v5Adrian Schmutzler2019-04-083-7/+18
| | | | | | | | | | | | | The GPIO for the reset button for the Archer C7v5 changed from ar71xx to ath79. An investigation based on tests revealed that the A7v5 responds on "11", while the C7v5 responds on "5" as set for ar71xx. Thus, we just define this in the DTS files instead of in the common DTSI. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Utilize new LED modes from diag.sh for Archer A7/C7 v5Adrian Schmutzler2019-04-081-1/+4
| | | | | Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consolidate LEDs in Archer A7/C7 v5 DTSIAdrian Schmutzler2019-04-081-48/+46
| | | | | | | | Definition is split here without obvious reason. Just merge it (and align order to that from C7 v4). Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti airCube ISPChristian Mauderer2019-04-084-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer <oss@c-mauderer.de> [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for OCEDO UrsusMarkus Scheck2019-04-084-2/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm Atheros QCA9558 RAM: 128MB FLASH: 16MB (Macronix MX25L12845EMI-10G) WLAN1: QCA9558 2.4GHz 802.11bgn 3SS WLAN2: QCA9880 5GHz 802.11ac 3SS LED: Power, LAN1, LAN2, 2.4GHz, 5GHz Serial:Next to SPI Flash, Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3) The Serial setting is 115200-8-N-1 INSTALLATION: 1. Serve an OpenWrt ramdisk image named "ursus.bin". Set your IP-address to 192.168.100.8/24. 2. Connect to the serial. Power up the device and interrupt the boot process. 3. Set the correct bootcmd with > setenv bootcmd run bootcmd_1 > saveenv 4. Run > tftpboot 0x81000000 ursus.bin > bootm 0x81000000 5. Wait for OpenWrt to boot up. 6. Transfer OpenWrt sysupdate image and flash via sysupgrade. Signed-off-by: Markus Scheck <markus.scheck1@gmail.com> Tested-by: David Bauer <mail@david-bauer.net> [whitespace fix, renamed LED labels and SoC type fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ag71xx: Enable tx hang workaround for the rest of ar724x SoCsPetr Štetiar2019-04-081-1/+8
| | | | | | | | | | | In ar71xx we check for stuck DMA on devices which fall in the is_ar724x SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x). In ath79 we're currently performing this check only for devices with ar7240 SoC, so this patch tries to sync the dma stuck checking behavior with what is being done in ar71xx. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.19 to 4.19.34Koen Vandeputte2019-04-082-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed: - 030-PCI-dwc-skip-MSI-init-if-MSIs-have-been-explicitly-d.patch Altered: - 366-netfilter-nf_flow_table-clean-up-and-fix-dst-handlin.patch - 650-netfilter-add-xt_OFFLOAD-target.patch - 662-remove_pfifo_fast.patch - 332-arc-add-OWRTDTB-section.patch - 100-clocksource-drivers-arch_timer-Workaround-for-Allwin.patch - 702-phy_add_aneg_done_function.patch New symbols: - ARC_IRQ_NO_AUTOSAVE - SUN50I_ERRATUM_UNKNOWN1 Compile-tested: cns3xxx, imx6, sunxi Runtime-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for NEC Aterm WG1200CRINAGAKI Hiroshi2019-04-065-7/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - SoC : Qualcomm Atheros QCA9563 - RAM : DDR2 128 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9563 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100/1000 Mbps - Switch : QCA8334 - LEDs/Input : 12x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from power connector side - 115200 bps Flash instruction using factory image: 1. Boot WG1200CR normaly 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Known issues: - cannot be controlled LEDs other than Power (Green/Red) - only Power LEDs are connected to SoC GPIO; other LEDs connected to the gpiochip on ath10k chip (QCA9888) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit message formatting]
* ath79: Utilize tplink-safeloader definitionAdrian Schmutzler2019-04-062-19/+6
| | | | | | | | | | | | | | | | | Currently, tplink-safeloader definition is only used a base for another common definition. This patch adjusts tplink-safeloader so it can be actually used for some targets in generic-tp-link.mk. This patch is cosmetic except for the order of "check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged for the tplink_re350k-v1 . Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's extra IMAGE/sysupgrade.bin rule]
* ath79: engenius epg5000: add leds migration scriptTomasz Maciej Nowak2019-04-061-0/+16
| | | | | | | | | | | | | | | With transition from ar71xx to ath79 some of devices change their naming of LEDs. When upgrading from ar71xx target images this will require the user to adjust previously working configuration. This commit adds migration script which can be used to rename old names to new ones. With this previously working configuration will be automatically adjusted, wihtout user intervention. This commit adds migration case for EnGenius EPG5000, the wireless LEDs names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to epg5000:blue:wlan2g and epg5000:blue:wlan5g. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add support for TP-Link CPE210 v2Adrian Schmutzler2019-04-024-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 This is based on the support patch for the identical CPE210 v3 by Mario Schroen <m.schroen@web.de>. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for TP-Link CPE210 v3Mario Schroen2019-04-025-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: Qualcomm Atheros QCA9533 (650MHz) * RAM: 64MB * Storage: 8 MB SPI NOR * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Thanks to robimarko for the work inside the ar71xx tree. Thanks to adrianschmutzler for deep discussion and fixes. Signed-off-by: Mario Schroen <m.schroen@web.de> [Split into DTS/DTSI, read-only config partition in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename, light subject touches] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for COMFAST CF-E5/E7Ding Tengfei2019-03-245-10/+175
| | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on Qualcomm/Atheros QCA9531. Short specification: 2x 10/100 Mbps Ethernet, with 24v PoE support 64 MB of RAM (DDR2) 16 MB of FLASH (SPI) 2T2R 2.4 GHz, 802.11b/g/n built-in 1x 3 dBi antennas output power (max): 80 mW (19 dBm) Qucetel EC20 LTE MODULE(1x external detachable antenna) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [commit subject fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add TP-Link TL-WR710N v1Marcin Jurkowski2019-03-244-0/+149
| | | | | | | | | | | | | | | | | | | | | This commit adds support for TP-Link TL-WR710N v1 router. CPU: Atheros AR9331 400MHz RAM: 32MB FLASH: 8MiB PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN WiFi: Atheros AR9331 1x2:1 bgn USB: ChipIdea HDRC USB2.0 LED: SYS BTN: Reset Sysupgrade from `ar71xx` works without glitches. Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0` respectively, what's consistent with `ar71xx` target. Wireless radio path is automatically upgraded from `platform/ar933x_wmac` to `platform/ahb/18100000.wmac`. Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
* ath79: add support for TP-Link TL-WR941N v7 (CN)Chuanhong Guo2019-03-243-2/+138
| | | | | | | | | | | | | | | | | This adds support for the Chinese version of TL-WR941N v7. It uses QCA9558+AR8236 while the international version uses TP9343 instead. Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 4 MB - RAM: 64 MB - Ethernet: Atheros AR8236 with 5 FE ports Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: remove switch driver in ag71xxChuanhong Guo2019-03-242-1345/+0
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: use ar8216 for builtin switchChuanhong Guo2019-03-247-10/+17
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for linux 4.19Chuanhong Guo2019-03-2440-0/+7053
| | | | | | | | | | | | | | | | | | | | | The following patches are dropped because they are merged upstream: -0001-tty-serial-drop-QCA-pecific-SoC-symbols.patch -0006-usb-drop-deprecated-symbols.patch -0009-MIPS-ath79-add-lots-of-missing-registers.patch -0010-MIPS-ath79-add-support-for-QCA953x-QCA956x-TP9343.patch -0014-MIPS-ath79-finetune-cpu-overrides.patch -0015-MIPS-ath79-enable-uart-during-early_prink.patch -0016-MIPS-ath79-get-PCIe-controller-out-of-reset.patch This patch is dropped due to the introduction of spi-mem framework: -461-spi-ath79-add-fast-flash-read.patch Thank to Michael Marley @mamarley for his work on this patch: -910-unaligned_access_hacks.patch Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [synchronized kernel config with make kernel_oldconfig] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ag71xx: pass correct device pointer to dma functionsChuanhong Guo2019-03-241-7/+7
| | | | | | | | | linux 4.19 doesn't accept a NULL device for these functions. It also complains that the device struct in net_device doesn't have a dma_mask set. Pass the device struct from platform_device for these functions. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: add support for timer functions in linux 4.15+Chuanhong Guo2019-03-241-0/+10
| | | | | | | Kernel newer than 4.15 dropped "data" field and used from_timer to cast out the parent struct pointer for current timer. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: bump 4.14 to 4.14.107Koen Vandeputte2019-03-221-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: Add support for Ubiquiti NanoBeam ACTobias Schramm2019-03-225-0/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-14 16:42:36 +0000