aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* ath79: fix SOC version in compat string for A770Piotr Dymacz2019-07-311-1/+1
| | | | | | YunCore A770 is based on QCA9531, not QCA9533. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for ALFA Network AP121FRoger Pueyo Centelles2019-07-314-0/+148
| | | | | | | | | | | | | This commit ports support for the ALFA Network AP121F, a pocket-size router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the ath79 target (it was already supported in ar71xx; see commit 0c6165d2 for more details). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env partition writable] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: fix indent in TP-Link TL-WR842N v3 DTS fileAdrian Schmutzler2019-07-301-1/+1
| | | | | | Convert leading spaces to tab to match rest of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove lines-initial-states propertyDavid Bauer2019-07-252-2/+0
| | | | | | | | | The lines-initial-states property was an early attempt to set the latch bit of the shift register on driver probe. It is not implemented in the driver and was rejected upstream. The latch bit was always set by a GPIO hog, so this property is safe to drop. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix indent in 01_ledsAdrian Schmutzler2019-07-241-2/+2
| | | | | | | | | Change capitalization from spaces to tabs in order to match the style of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [fix capitalization in commit title, add short description] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DIR-842 C2Jackson Lim2019-07-246-0/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C2: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: 2.0 Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim <jackcolentern@gmail.com> [Reword reset-hog comment, fix formatting] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: modify device name of I-O DATA WN-AC1600DGR2INAGAKI Hiroshi2019-07-182-5/+6
| | | | | | | | | | | | | | | | | | | | | | | The hardware of I-O DATA WN-AC1600DGR3 has completely compatibility with WN-AC1600DGR2, so modify the device name of WN-AC1600DGR2 to show the images for DGR2 also support DGR3. Specification of WN-AC1600DGR3: - SoC : Qualcomm Atheros QCA9557 - RAM : DDR2 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : QCA9557 (SoC), 2T2R - 5 Ghz : QCA9880, 3T3R - Ethernet : 5x 10/100/1000 Mbps - Switch : QCA8337N - LEDs/Input : 6x/6x (4x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, GND, TX, RX from ethernet port side - 115200n8 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Add support for TP-Link Archer C60 v2Adrian Schmutzler2019-07-185-2/+79
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60 v2 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed IP address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery Flash instruction (under U-Boot, using UART): tftp 0x81000000 ...-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C60 v1Adrian Schmutzler2019-07-186-1/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 ...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE510-v2/v3Andrew Cameron2019-07-186-0/+215
| | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, and 4 green LEDs - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in) - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna - Adjustable transmission power from 0 to 23dBm/200mw Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Trendnet TEW-823DRUPramod Pancha2019-07-185-1/+249
| | | | | | | | | | | | | | | | | | | | | Trendnet TEW-823DRU is a dual-band AC1750 router. The router is based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: 720 MHz CPU 256 MB of RAM 16 MB of FLASH 3T3R 2.4 GHz 3T3R 5 GHz 5x 10/100/1000 Mbps Ethernet Firmware can be flashed from the web interface. Tested on 3 routers with no issues. Signed-off-by: Pramod Pancha <pancha@vill.com> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link RE355 v1 and RE450 v1Christoph Krapp2019-07-178-0/+240
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: Qualcomm Atheros QCA9558 RAM: 64/128MiB Flash: 8MiB SPI-NOR Wifi: - 2.4GHz: 3T3R (QCA9558) - 5GHz: 3T3R (QCA9880) LAN: 1x 10/100/1000 Mbps UART: - TP1: Tx - TP2: Rx - TP3: Gnd - TP4: 3v3 Flash instructions: Flash factory image through stock firmware WEB UI. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: add support for Bluesocket BSAP1880 boardDaniel Gimpelevich2019-07-178-0/+173
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: widen RedBoot directory search and add PHYDaniel Gimpelevich2019-07-171-1/+2
| | | | | | | | The Bluesocket BSAP1880 board has a Vitesse PHY, for which the driver was not being included, and its RedBoot directory block is earlier in the flash than the search was allowing. This commit prepares for supporting it. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ath79: support "rgmii-id" PHY mode in ag71xxDaniel Gimpelevich2019-07-171-0/+2
| | | | | | | The ag71xx code did not include a case for the "rgmii-id" PHY mode in the code. There are devices that need this mode, so I'm adding it. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* ath79: ar9330: add missing watchdog nodePetr Štetiar2019-07-171-0/+10
| | | | | | | | It was reported in FS#2385, that Carambola2 doesn't currently have working watchdog so fix it by adding watchdog node. Ref: FS#2385 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-3/+3
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: add seama header fixup for Qihoo C301Chuanhong Guo2019-07-161-0/+15
| | | | | | | | | This script is copied from ar71xx. Without a header fixup, u-boot checksum for kernel will fail after the first boot. Fixes: a9360452f0 ("ath79: add support for Qihoo C301") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add wmac migration for all ar93xx/qca95xx SoCsChuanhong Guo2019-07-161-5/+6
| | | | | | | Add migration for all ar71xx device path as well as previously incorrect ath79 path. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar93xx/qca95xx: move gmac/wmac/pcie node out of apb busChuanhong Guo2019-07-165-123/+123
| | | | | | | | according to functional block diagram in datasheet, these devices don't belong to apb bus. Move these nodes out to match datasheet description. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Qihoo C301Chuanhong Guo2019-07-168-0/+280
| | | | | | | | | | | | | | | | Specifications: - SoC: AR9344 - RAM: 128MB - Flash: 2 * 16MB (MX25L12845) - Ethernet: 2 * FE LAN & 1 * FE WAN - WiFi: 2.4G: AR9344 5G: QCA9882 Flash instruction: 1. Hold reset and power up the router 2. Set your IP to 192.168.1.x 3. Open 192.168.1.1 and upload the generated *factory* firmware Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for devolo WiFi pro 1750xDavid Bauer2019-07-144-1/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED Power (non-controllable) 1x LED Status (internal) 1x LED LAN (controlled by PHY) 1x LED WLAN BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to external-LED header. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix missing DEVICE_VENDOR for some devicesChen Minqiang2019-07-102-0/+2
| | | | Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ath79: Fix whitespace errors in 11-ath10k-caldataAdrian Schmutzler2019-07-091-2/+2
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add missing IMAGE_SIZE for Etactica EG200Adrian Schmutzler2019-07-081-0/+1
| | | | | | | The Etactica EG200 is the only device in ath79 despite nand target that lacks IMAGE_SIZE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: increase kernel partition size for CPE610v1Andrew Cameron2019-07-072-4/+7
| | | | | | | | | Increase the Kernel partition to address the issue discussed here https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5 Switch Back to the okli Loader to support increased partition size Signed-off-by: Andrew Cameron <apcameron@softhome.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
* ath79: Add DEVICE_VENDOR for Ubiquiti RouterstationAdrian Schmutzler2019-07-051-0/+1
| | | | | | | | This has been overlooked. Reported by: Chen Minqiang (@ptpt52) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Correctly use DEVICE_VARIANT for NETGEAR WNDR3700Adrian Schmutzler2019-07-041-1/+3
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Move DEVICE_VENDOR for NETGEAR to parent definitionAdrian Schmutzler2019-07-043-6/+1
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: split DEVICE_TITLE in multiple variablesPaul Spooren2019-07-048-140/+274
| | | | | | | | | | | | | | This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ath79: Use -v1 suffix for TP-Link WDR3600/4300Adrian Schmutzler2019-07-035-14/+14
| | | | | | | | | | | | | | | In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have been used while most other TP-Link devices include the revision. Although there actually is only one major revision of these devices, they bear the revision on their bottom (v1.x). TP-Link also refers to the devices as V1 on its web page. This patch thus adds -v1 to both so it is more consistent with other devices and with what you would expect from reading the on-device sticker and the support pages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix "spi-gpio: convert deprecated binding"Christian Lamparter2019-06-254-8/+8
| | | | | | | | This patch fixes the previous commit that rendered the devices (mostly leds) useless. Fixes: 1fa24de8c29b ("ath79: spi-gpio: convert deprecated binding") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: Code style improvements in 10_fix_wifi_macAdrian Schmutzler2019-06-251-4/+4
| | | | | | This fixes one comparison and several useless echos. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE610-v1Andrew Cameron2019-06-244-0/+155
| | | | | | | | | | | | | | | | | | | | | TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, WLAN5G green LEDs - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: spi-gpio: convert deprecated bindingChristian Lamparter2019-06-244-8/+8
| | | | | | | The old gpio-{sck,miso and mosi} binding is deprecated in favour of {sck,miso and mosi}-gpios. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: Remove redundant LED GPIO definitions for Archer C25 v1Adrian Schmutzler2019-06-241-4/+0
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: correct various phy-mode propertiesDavid Bauer2019-06-206-4/+8
| | | | | | | | | | | | | | | | | | | | Upstream commit 6d4cd04 changes how the internal delays of the AR803x based PHYs are enabled. With this commit, all internal delays are disabled on driver probe and enabled based on the 'phy-mode' property in the device-tree. Before this commit, the RX delay was always enabled upon soft-reset while the TX delay retained it's previous state. A hard reset enabled the RX delay while the TX delay was disabled. Because of this inconsistency, wrongly specified PHY-modes were working correctly while the hardware was in a different state. Fix the PHY-modes of some affected devices (and clean up misplaced properties along the way) to keep the devices working flawlessly with kernels >= 5.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: kernel: bump some targets to 4.19Petr Štetiar2019-06-181-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lets bump kernel to 4.19 on targets which were run tested or got ACKed so we've enough time to make it ready for next release: armvirt/32 (runtested in qemu) armvirt/64 (runtested in qemu) ath79/generic (runtested on Carambola2) gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R) imx6/generic (runtested on Apalis) ipq40xx/generic (runtested on nbg6617) malta/be64 (runtested in qemu) malta/be (runtested in qemu) malta/le (runtested in qemu) malta/le64 (runtested in qemu) mpc85xx/generic (runtested on TL-WDR4900) mpc85xx/p2020 (runtested on P2020RDB) mvebu/cortexa53 mvebu/cortexa72 mvebu/cortexa10 octeon/generic (runtested on EdgeRouter Lite) sunxi/cortexa53 (build tested only) sunxi/cortexa7 (runtested on Lime2-K) sunxi/cortexa8 (build tested only) tegra/generic x86/64 (runtested in qemu) Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi] Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini] Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra] Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon] Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.19 to 4.19.52Koen Vandeputte2019-06-183-4/+4
| | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-11479 - CVE-2019-11478 - CVE-2019-11477 Also fix a malformed patch issue caught during refresh. It was caused by removing a whitespace without altering the index values in a patch which alters a patch. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Fixes: cf6526249298 ("kernel: bump 4.19 to 4.19.51") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.127Koen Vandeputte2019-06-183-4/+4
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-11479 - CVE-2019-11478 - CVE-2019-11477 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: Add SUPPORTED_DEVICES for Archer C7 v1/v2Adrian Schmutzler2019-06-151-0/+2
| | | | | | | | The identifier for both devices is "archer-c7" on ar71xx, set here: https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L348 https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L511 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Merge cases in 11-ath10k-caldataAdrian Schmutzler2019-06-151-5/+2
| | | | | | Cosmetical patch that just merges two cases. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 4.19 to 4.19.50Koen Vandeputte2019-06-122-3/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)Koen Vandeputte2019-06-122-3/+3
| | | | | | | | | | | | | | | | Refreshed all patches. This bump contains upstream commits which seem to avoid (not properly fix) the errors as seen in FS#2305 and FS#2297 Altered patches: - 403-net-mvneta-convert-to-phylink.patch - 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: Add support for TP-Link Archer C25 v1Adrian Schmutzler2019-06-106-9/+231
| | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip, but not all of them as e.g. for the C59. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Reorder some TP-Link Archer devices in 01_ledsAdrian Schmutzler2019-06-101-8/+8
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: migrate Archer C7 5GHz radio device pathsDavid Santamaría Rogado2019-06-101-6/+20
| | | | | | | | | | | | | | | | | | When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79, the 5ghz radio stops working because the device path changed. Some people subtitute the unsupported QCA9880v1 in the Archer v1 with supported QCA9880v2 radio. Since the stock radio doesn't work, so it's safe to apply the change also for the Archer v1 images as well. Also this patch renames the migration file and variables from wmac to wifi. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed comment, added return 0 (not that it matters since uci is clever, see 00-wmac-migration thread), reworded commit message]
* ath79: Consistently label art partition with lower caseAdrian Schmutzler2019-06-1019-36/+33
| | | | | | | | This patch harmonizes the label and alias for art partitions across ath79. Since lower case seems to be more frequent, use that consistently. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Read MAC addresses from flash in 11-ath10k-caldataAdrian Schmutzler2019-06-101-14/+23
| | | | | | | | | | In commit c3a8518 eth0 and eth1 have been swapped for some devices, but 11-ath10k-caldata has not been updated. Instead of fixing this by swapping eth0/eth1, this patch will read addresses from flash (as done for several devices already) so adjustments due to eth order become obsolete. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consistently label info partitionAdrian Schmutzler2019-06-107-15/+9
| | | | | | | | | | | | | | | | The info/product-info partition, which frequently contains MAC adresses, is typically assigned the 'info' alias in DTS, but then labelled with 'info', 'product-info' or 'config'. This leads to different aliases if used for setting MAC adresses in DTS compared to when using e.g. mtd_get_mac_binary. Occationally, also multiple switch-case entries are used just because of different labelling. This patch relabels those partitions in ath79 to consistently use 'info'. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>