aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* kernel: 5.4: move some kconfig options to genericYousong Zhou2020-03-101-6/+0
| | | | | | | | | | | CONFIG_64BIT_TIME=y CONFIG_KASAN_STACK=1 CONFIG_UBSAN_ALIGNMENT=y CONFIG_UNIX_SCM=y CONFIG_DMA_DECLARE_COHERENT=y CONFIG_OF_RESERVED_MEM=y Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ath79: fix indent for wrapped lines in image/nand.mkAdrian Schmutzler2020-03-071-3/+3
| | | | | | | This applies the common indent (one tab) for the wrapped lines of domywifi_dw33d and glinet_gl-ar750s-nor-nand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Sitecom WLR-8100Davide Fioravanti2020-03-075-3/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-8100 v1 002 (marketed as X8 AC1750) is a dual band wireless router. Specification: - Qualcomm Atheros SoC QCA9558 - 128 MB of RAM (DDR2) - 16 MB of FLASH (Macronix MX25L12845EMI-10G - SPI NOR) - 5x 10/100/1000 Mbps Ethernet - 3T3R 2.4 GHz (QCA9558 WMAC) - 3T3R 5.8 Ghz (QCA9880-BR4A) - 1x USB 3.0 (Etron EJ168A) - 1x USB 2.0 - 9x LEDs - 2x GPIO buttons Everything working. Installation and restore procedure tested Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Toolbox > Firmware, 4. Browse for OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Restore OEM FW (Linux only) 1. Download OEM FW from website (tested with WLR-8100v1002-firmware-v27.dlf) 2. Compile the FW for this router and locate the "mksenaofw" tool in build_dir/host/firmware-utils/bin/ inside the OpenWrt buildroot 3. Execute "mksenaofw -d WLR-8100v1002-firmware-v27.dlf -o WLR-8100v1002-firmware-v27.dlf.out" where: WLR-8100v1002-firmware-v27.dlf is the path to the input file (use the downloaded file) WLR-8100v1002-firmware-v27.dlf.out is the path to the output file (you can use the filename you want) 4. Flash the new WLR-8100v1002-firmware-v27.dlf.out file. WARNING: Do not keep settings. Additional notes. The original firmware has the following button configuration: - Press for 2s the 2.4GHz button: WPS for 2.4GHz - Press for 2s the 5GHz button: WPS for 5GHz - Press for 15s both 2.4GHz and 5GHz buttons: Reset I am not able to replicate this behaviour, so I used the following configuration: - Press the 2.4GHz button: RFKILL (disable/enable every wireless interfaces) - Press the 5GHz button: Reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ath79: add support for Devolo Magic 2 WIFIManuel Giganto2020-03-076-0/+206
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch support Devolo Magic 2 WIFI, board devolo_dlan2-2400-ac. This device is a plc wifi AC2400 router/extender with 2 Ethernet ports, has a G.hn PLC and uses LCMP protocol from Home Grid Forum. Hardware: SoC: AR9344 CPU: 560 MHz Flash: 16 MiB (W25Q128JVSIQ) RAM: 128 MiB DDR2 Ethernet: 2xLAN 10/100/1000 PLC: 88LX5152 (MaxLinear G.hn) PLC Flash: W25Q32JVSSIQ PLC Uplink: 1Gbps MIMO PLC Link: RGMII 1Gbps (WAN) WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9882-BR4A 5GHz 802.11ac Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2 Button: 3x Buttons (Reset, wifi and plc) LED: 3x Leds (wifi, plc white, plc red) GPIO Switch: 11-PLC Pairing (Active Low) 13-PLC Enable 21-WLAN power MACs Details verified with the stock firmware: Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002 Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006 Ethernet &ethernet *:4e = 2.4 GHz + 2 PLC uplink --- *:4f = 2.4 GHz + 3 Label MAC address is from PLC uplink OEM SSID: echo devolo-$(grep SerialNumber /dev/mtd1 | grep -o ...$) OEM WiFi password: grep DlanSecurityID /dev/mtd1|tr -d -|cut -d'=' -f 2 Recommendations: Configure and link your PLC with OEM firmware BEFORE you flash the device. PLC configuration/link should remain in different memory and should work straight forward after flashing. Restrictions: PLC link detection to trigger plc red led is not available. PLC G.hn chip is not compatible with open-plc-tools, it uses LCMP protocol with AES-128 and requires different software. Notes: Pairing should be possible with gpio switch. Default configuration will trigger wifi led with 2.4Ghz wifi traffic and plc white led with wan traffic. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.100 2. Download the sysupgrade image and rename it to uploadfile 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Allow 1-2 minutes for the first boot. Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
* ath79: add support for DomyWifi DW33DWeiDong Jia2020-03-074-0/+243
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit ports the device from ar71xx to the ath79 target and modifies the partition layout. 1. Firmware is installed to nand flash. 2. Modify the uboot-env parameter to boot from the nand flash. 3. The kernel size is extended to 5M. 4.nor flash retains the oem firmware. oem partition layout dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00e30000 00010000 "rootfs" mtd3: 00170000 00010000 "kernel" mtd4: 00010000 00010000 "art" mtd5: 00f90000 00010000 "firmware" mtd6: 06000000 00020000 "rootfs_data" mtd7: 02000000 00020000 "backup" new partition layout dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00fa0000 00010000 "oem-firmware" mtd3: 00010000 00010000 "art" mtd4: 00500000 00020000 "kernel" mtd5: 05b00000 00020000 "ubi" mtd6: 02000000 00020000 "oem-backup" MAC address overview: All mac addresses are stored in the art partition. eth0: 0x0 eth1: 0x6 ath9k: 0xc ath10k: 0x12 No valid addresses in 0x1002 and 0x5006. All addresses match the OEM firmware. Install from oem firmware. Enable ssh service: Connect to the router web, click professional, click system-startup, and add dropbear in the local startup input box. Click system-administration, delete ssh-key, and replace your ssh pub key. Restart the router. 1.Upload openwrt firmware to the device scp openwrt-snapshot-r11365-df60a0852c-ath79-nand-domywifi_dw33d-\ squashfs-factory.bin root@192.168.10.1:/tmp 2.modify uboot-env. ssh login to the device: fw_setenv bootcmd 'nboot 0x8050000 0;bootm || bootm 0x9fe80000' Run the fw_printenv command to check if the settings are correct. 3.Write openwrt firmware. ssh login to the device: mtd -r write /tmp/openwrt-snapshot-r11365-df60a0852c-ath79-nand-\ domywifi_dw33d-squashfs-factory.bin /dev/mtd6 The device will restart automatically and the openwrt firmware installation is complete. Restore oem firmware.just erase the kernel partition and the ubi partition. ssh login to the device: mtd erase /dev/mtd4 mtd -r erase /dev/mtd5 Reboot the device Signed-off-by: WeiDong Jia <jwdsccd@gmail.com> [alter flash instruction in commit message] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: re-add accidentally dropped patch to kernel 5.4Daniel Golle2020-03-064-14/+281
| | | | | | | | Patch 0061-tty-serial-ar933x-uart-rs485-gpio.patch wasn't included when adding support for kernel 5.4. Re-add it and refresh patches. Fixes: 53ab9865c2 ("ath79: add support for kernel 5.4") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* spi: ath79: remove spi-master setup and cleanup assignmentDavid Bauer2020-02-291-0/+28
| | | | | | | | | | | This removes the assignment of setup and cleanup functions for the ath79 target. Assigning the setup-method will lead to 'setup_transfer' not being assigned in spi_bitbang_init. Also drop the redundant cleanup assignment, as this also happens in spi_bitbang_init. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Make upstream ag71xx driver workHauke Mehrtens2020-02-285-4/+183
| | | | | | | | * Fix some bugs in the driver * Add missing clock and reset references in dts * Rename mdio-bus to mdio so the driver find it Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add support for kernel 5.4David Bauer2020-02-2846-7/+3812
| | | | | | | | | | | | | | | Signed-off-by: David Bauer <mail@david-bauer.net> [refreshed] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> * Sync the patches with the changes done for kernel 4.19 * Use KERNEL_TESTING_PATCHVER * Refresh the configuration * Fix multiple compile bugs in the patches * Only add own ag71xx files for kernel 4.19 and use upstream version for 5.4. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: also reduce spi-max-frequency for buffalo_wzr-hp-ag300hAdrian Schmutzler2020-02-271-2/+2
| | | | | | | | | | | In accordance to ebc090e420d1 ("ath79: reduce spi-max-frequency to 50 MHz") this also reduces the spi-max-frequency to 50 MHz for the last remaining device with higher frequency in ath79. This will save us from having a single special case that will require adjustment when the spi driver for this device is changed in the future. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: reduce spi-max-frequency to 50 MHzAdrian Schmutzler2020-02-276-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | The introduction of ebf0d8dadeca ("ath79: add new ar934x spi driver") made the SPI memory unusable on devices with very high spi-max-frequency (104 MHz). Here's how the actual clock is calculated: (AHB_CLK/((CLOCK_DIVIDER+1)*2)) where AHB_CLK is a fixed clock (e.g. 200MHz on AR9331) and CLOCK_DIVIDER is the parameter we can set. Highest clock according to this formula is AHB_CLK/2 (100MHz, but that didn't work in device tests). The next possible value is AHB_CLK/4 (50MHz). Speeds between 50 MHz and 100 MHz will be rounded down, so using values higher than 50 MHz does not provide any benefit. Consequently, this patch reduces spi-max-frequency for all devices with values higher than 50 MHz to 50 MHz (effectively, this only affects devices with 104 MHz before this patch). Tested on GL.inet GL-AR150: Boot fails with 104 MHz but is successful with both 50 MHz and 80 MHz (fast-read), where the latter two yield identical read speeds. Fixes: ebf0d8dadeca ("ath79: add new ar934x spi driver") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix spi-max-frequency for wAP G-5HacT2HnDRoger Pueyo Centelles2020-02-271-1/+1
| | | | | | | | | | The introduction of ebf0d8dade (ath79: add new ar934x spi driver) made the SPI memory unusable. Reducing the spi-max-frequency to a smaller value makes it work again. Tested on two MikroTik RouterBOARD wAP G-5HacT2HnD devices. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add support for MikroTik RouterBOARD 922UAGS-5HPacDRoger Pueyo Centelles2020-02-268-3/+245
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch ports support for the MikroTik RouterBOARD 922UAGS-5HPacD with a built-in 802.11ac High-Power radio (31dBm), which was already available in the ar71xx target. See https://mikrotik.com/product/RB922UAGS-5HPacD for more info. Specifications: - SoC: Qualcomm Atheros QCA9558 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9882 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V - SFP: 1x host - USB: 1x 2.0 type A - PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems) - SIM slot: 1x mini-SIM Working: - Board/system detection - SPI and NAND storage - PCIe - USB type A host - Wireless - Ethernet - LEDs (user, phy0) - Reset button - Sysupgrade to/from ar71xx Not supported: - RSSI LEDs - SFP cage Installation methods: - Sysupgrade from ar71xx (it is advisable to use the -n option to wipe any previous settings), or - Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add missing reset-gpios for NanoStation Loco M (XW)Roger Pueyo Centelles2020-02-241-0/+1
| | | | | | | | When porting support from ar71xx to ath79, the reset-gpios option was missed. Due to a hardware bug, this would eventually leave the devices with RX-deaf Ethernet PHY. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* kernel: bump 4.19 to 4.19.106Koen Vandeputte2020-02-242-17/+13
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0786-leds-pca963x-Fix-open-drain-initialization.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.105Koen Vandeputte2020-02-242-3/+3
| | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2013-1798 - CVE-2019-3016 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.171Koen Vandeputte2020-02-241-1/+1
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2013-1798 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: fix TP-Link TL-WA901ND v2 PHY stuck in resetDavid Bauer2020-02-231-0/+6
| | | | | | | | | | Some newer bootloaders for the TP-Link TL-WA901ND put the ethernet PHY in reset before loading the kernel, thus the LAN interface is not working in OpenWrt. Clear the reset to restore ethernet functionality. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: remove redundant includes in DTS filesAdrian Schmutzler2020-02-2217-50/+0
| | | | | | | | | Many DTS files contain the same includes again that are already present in the DTSI files they are derived from. Remove those redundant includes in the DTS files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Teltonika RUT955Daniel Golle2020-02-214-0/+397
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344) - built-in 4G/3G module (example: Quectel EC-25EU) - internal microSD slot (spi-mmc, buggy and disabled for now) - RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0) - RS422/RS485 (AR934x high speed UART, /dev/ttyATH1) - analog 0-24V input (MCP3221) - various digital inputs and outputs incl. a relay - 11x LED (4 are driven by AR9344, 7 by 74HC595) - 2x miniSIM slot (can be swapped via GPIO) - 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS) - 1x button (reset) - DC jack for main power input (9-30 V) - debugging UART available on PCB edge connector Serial console (/dev/ttyS0) pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2". Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* serial: ar933x_uart: add rs485 supportDaniel Golle2020-02-211-0/+271
| | | | | | | | | Add support for RS485 tranceiver with transmit/receive switch hooked to a RTS GPIO pin. Use the 'rts-gpios' and 'rs485-rts-active-low' properties as described in devicetree/bindings/serial/rs485.yaml. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for TP-Link TL-WA701ND/730RE/801ND/901ND v1Adrian Schmutzler2020-02-218-1/+89
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the various clones of the TL-WA830RE recently supported in fb99ac6807f2 ("ath79: add support for TP-Link TL-WA830RE v1"): - tplink,tl-wa701nd-v1 - tplink,tl-wa730re-v1 - tplink,tl-wa801nd-v1 - tplink,tl-wa830re-v1 (already supported) - tplink,tl-wa901nd-v1 Since these devices are 100%-clones in ar71xx, this patch adds all of them without run-testing (as this has been done for TL-WA830RE v1). Specifications: - SOC: Atheros AR7240 - CPU: 400MHz - Flash: 4 MiB (Spansion S25FL032P) - RAM: 32 MiB (Zentel A3S56D40FTP-G5) - WLAN: Atheros AR9280 bgn 2x2 - Ethernet: 1 port (100M) Flash instructions: - install from u-boot with tftp (requires serial access) > setenv ipaddr a.b.c.d > setenv serverip e.f.g.h > tftpboot 0x80000000 \ openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin > erase 0x9f020000 +0x3c0000 > cp.b 0x80000000 0x9f020000 0x3c0000 > bootm 0x9f020000 - flash factory image from OEM WebUI - sysupgrade from ar71xx image Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: correct Siemens WS-AP3610 blocksizeDavid Bauer2020-02-201-0/+1
| | | | | | | With the wrong blocksize, the rootfs was not positioned on the boundary of a block, thus breaking the mtdsplit driver. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add label MAC address for Ubiquiti Picostation M (XM)Adrian Schmutzler2020-02-191-0/+1
| | | | | | | This adds the label MAC address for the Ubiquiti Picostation M (XM). This was overlooked when adding support in the previous patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti Picostation M (XM)Adrian Schmutzler2020-02-195-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti Picostation M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - External antenna: 5 dBi (USA), 2 dBi (EU) - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti Nanostation Loco M (XM)Sven Roederer2020-02-195-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti Nanostation Loco M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - NS Loco M2: built-in antenna: 8 dBi; AR9287 - NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Note that only certain firmware versions accept unsigned images. Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin Tested on NanoStation Loco M2. Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloaderAdrian Schmutzler2020-02-193-10/+4
| | | | | | | | | | | Several devices with tplink-safeloader contain default values (0x0) for TPLINK_HWID and TPLINK_HWREV in their device definitions. Move those to common tplink-safeloader definition so they do not have to be repeated each time. While at it, set default value for tplink-v1 and tplink-v2 as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add gpio4 pinmux on TL-WR841N/ND v8, WR842N v2, MR3420 v2Adrian Schmutzler2020-02-181-4/+8
| | | | | | | | | | | | | | | | | | | | | This adds a pinmux to the shared DTSI for TP-Link TL-WR841N/ND v8, TL-WR842N v2 and TL-MR3420 v2. It is supposed to be the equivalent of: /* config gpio4 as normal gpio function */ ath79_gpio_output_select(TL_MR3420V2_GPIO_USB_POWER,AR934X_GPIO_OUT_GPIO); This allows to enable USB power on these devices. While at it, move the jtag_disable_pins to &gpio node and remove the redundant status=okay there. Tested on TP-Link TL-WR842N v2. Fixes: FS#2753 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Armin Fuerst <armin@fuerst.priv.at>
* ath79: move mikrotik-caldata.sh to target base-filesAdrian Schmutzler2020-02-171-0/+0
| | | | | | | | | | | | | | Mikrotik devices will be found in both generic and nand subtargets. The file mikrotik-caldata.sh, currently used in generic, contains a few lines of code that would need to be duplicated for nand support. Instead of duplicating it, move it to target base-files, as size impact is small and the maintenance gain should outweigh it. This is changed separately to make life easier for the people currently working on Mikrotik NAND support. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Siemens WS-AP3610David Bauer2020-02-166-0/+218
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Atheros AR7161 RAM: Samsung K4H511638D-UCCC 2x 64M DDR1 SPI: Micron M25P128 (16M) WiFi: Atheros AR9160 bgn Atheros AR9160 an ETH: Broadcom BCM5481 LED: Power (Green/Red) ETH (Green / Blue / Yellow) (PHY-controlled) WiFi 5 (Green / Blue) WiFi 2 (Green / Blue) BTN: Reset Serial: Cisco-Style RJ45 - 115200 8N1 Installation ------------ 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to 1401A8C0.img. Configure the TFTP server to listen at 192.168.1.66/24. 2. Connect the TFTP server to the access point. 3. Connect to the serial console of the access point. Attach power and interrupt the boot procedure when prompted (bootdelay is 1 second). 4. Configure the U-Boot environment for booting OpenWrt from Ram and flash: $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000' $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66; tftpboot; bootm' $ saveenv 5. Load OpenWrt into memory: $ run ramboot_openwrt Wait for the image to boot. 6. Transfer the OpenWrt sysupgrade image to the device. Write the image to flash using sysupgrade: $ sysupgrade -n /path/to/openwrt-sysuograde.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: backport phy reset-controller patchesDavid Bauer2020-02-162-0/+151
| | | | | | | | | | The Siemens WS-AP3610 asserts reset to the ethernet PHY with the reset-register. Backport the necessary patches to de-assert reset when probing the PHY. These patches can be dropped when using kernel 5.4. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WR940N v6Adrian Schmutzler2020-02-134-0/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TL-WR940N v6 is similar to v3/v4, it just has different LEDs and MAC address assignment. Specification: - 750 MHz CPU - 32 MB of RAM - 4 MB of FLASH - 2.4 GHz WiFi - 4x 10/100 Mbps Ethernet The use of LEDs is based on ar71xx, so blue LED is used for WAN and orange LED for diag (boot/failsafe/etc.). Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wr940nv6_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Thanks to Manuel Kock for reviewing and testing this patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Manuel Kock <github.web@manu.li>
* ath79: enable forceless sysupgrade from ar71xx on fritz300eAdrian Schmutzler2020-02-131-0/+1
| | | | | | | This adds the ar71xx board name to the SUPPORTED_DEVICES on ath79, so forceless sysupgrade on this device becomes possible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WA830RE v1Christian Buschau2020-02-116-1/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This ports support for the TL-WA830RE v1 range extender from ar71xx to ath79. Specifications: - SOC: Atheros AR7240 - CPU: 400MHz - Flash: 4 MiB (Spansion S25FL032P) - RAM: 32 MiB (Zentel A3S56D40FTP-G5) - WLAN: Atheros AR9280 bgn 2x2 - Ethernet: 1 port (100M) Flash instructions: - install from u-boot with tftp (requires serial access) > setenv ipaddr a.b.c.d > setenv serverip e.f.g.h > tftpboot 0x80000000 \ openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin > erase 0x9f020000 +0x3c0000 > cp.b 0x80000000 0x9f020000 0x3c0000 > bootm 0x9f020000 - flash factory image from OEM WebUI - sysupgrade from ar71xx image The device seems to be a clone of the following devices not yet added to ath79: - tl-wa701nd-v1 - tl-wa730re-v1 - tl-wa801nd-v1 - tl-wa901nd-v1 Signed-off-by: Christian Buschau <christian.buschau@mailbox.org> [make use of ar7240_tplink.dtsi, add note about clones] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: reorganize DTSI for ar7240 TP-Link devicesAdrian Schmutzler2020-02-118-46/+57
| | | | | | | | | | | | | | | | The current set of TP-Link devices with ar7240 SoC all share the same DTSI file. As the latter is very similar to the definition required for the to-be-supported TP-Link TL-WA devices with ar7240, this patch splits the definitions into a shared part for all TP-Link devices (ar7240_tplink.dtsi) and a file containing the specific setup for the present TL-WR devices (ar7240_tplink_tl-wr.dtsi), equivalent to the former ar7240_tplink_tl-wr74xn-v1.dtsi. While at it, remove unused firmware partition label and rename pinmux_switch_led_pins. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: restore pin state on probe for ar934x-spiChuanhong Guo2020-02-101-5/+11
| | | | | | | | | | | | If bootloader doesn't terminate its last spi operation properly before starting kernel, our first transfer in kernel becomes a continuous transfer to that request instead of a new one. Fix this flaw by restoring IOC register, which restored all pin state to default. Fixes: ebf0d8dade ("ath79: add new ar934x spi driver") Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add LED trigger for TL-WR902AC v1 WAN LEDLech Perczak2020-02-071-0/+1
| | | | | | | | | | | Inspired by commit c48b571ad708, add an LED trigger for the WAN LED on top of the TP-Link TL-WR902AC v1. Currently, only the LED on the port itself shows the link state, while the LED on top of the device stays dark. The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at the port was labeled LAN. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for Atheros AR934x HS UARTDaniel Golle2020-02-072-0/+65
| | | | | | | | | AR934x chips also got the 'old' qca,ar9330-uart in addition to the 'new' ns16550a compatible one. Add support for UART1 clock selector as well as device-tree bindings in ar934x.dtsi to make use of that uart. Reported-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDEDaniel Golle2020-02-071-0/+64
| | | | | | | | | | | | | | | | On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x does not do any harm, so just set them unconditionally. Tested-by: Chuanhong Guo <gch981213@gmail.com Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: ag71xx: use netif_receive_skb_list on 4.19Chuanhong Guo2020-02-071-1/+19
| | | | | | | | This new function make batch processing of network packets possible, which slightly improves performance. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Tested-by: Rosen Penev <rosenp@gmail.com>
* ath79: use ar934x-spi for ar933x as wellChuanhong Guo2020-02-061-3/+2
| | | | | | | | ar933x appears to have the same spi controller as ar934x but it's not mentioned in datasheet at all. Use new spi driver instead to gain more flash operating performance. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add new ar934x spi driverChuanhong Guo2020-02-0611-15/+346
| | | | | | | | | | | A new shift mode was introduced since ar934x which has a way better performance than current bitbang driver and can handle higher spi clock properly. This commit adds a new driver to make use of this new feature. This new driver has chipselect properly configured and we don't need cs-gpios hack in dts anymore. Remove them. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: bump 4.19 to 4.19.101Koen Vandeputte2020-02-041-1/+1
| | | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14896 - CVE-2019-14897 Remove upstreamed: - 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch - 950-0202-staging-bcm2835-camera-fix-module-autoloading.patch - 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: WNDR3700 v1/v2: make u-boot env partition writableMichal Cieslakiewicz2020-02-042-2/+0
| | | | | | | Remove read-only flag from U-boot environment partition for Netgear WNDR3700 v1 and v2 so u-boot-envtools can modify data there. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for COMFAST CF-E560ACAugust Huber2020-02-035-6/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the COMFAST CF-E560AC, an ap143 based in-wall access point. Specifications: - SoC: Qualcomm Atheros QCA9531 - RAM: 128 MB DDR2 (Winbond W971GG6SB-25) - Storage: 16 MB NOR (Winbond 25Q128JVSO) - WAN: 1x 10/100 PoE ethernet (48v) - LAN: 4x 10/100 ethernet - WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM - WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM - USB: one external USB2.0 port - UART: 3.3v, 2.54mm headers already populated on board - LED: 7x external - Button: 1x external - Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod) MAC addressing: - stock LAN *:40 (label) WAN *:41 5G *:42 2.4G *:4a - flash (art partition) 0x0 *:40 (label) 0x6 *:42 0x1002 *:41 0x5006 *:43 This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and 0x5006, however the vendor firmware only reads from art:0x0 for the LAN interface and then increments in 02_network. They also jump 8 addresses for the second wifi interface (2.4 GHz). This behavior has been duplicated in the DTS and ath10k hotplug to align addresses with the vendor firmware v2.6.0. Recovery instructions: This device contains built-in u-boot tftp recovery. 1. Configure PC with static IP 192.168.1.10/24 and tftp server. 2. Place desired image at /firmware_auto.bin at tftp root. 3. Connect device to PC, and power on. 4. Device will fetch flash from tftp, flash and reboot into new image. Signed-off-by: August Huber <auh@google.com> [move jtag_disable_pins, remove unnecessary statuses in DTS, remove duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: WNDR3700 v2: add dash before version in device nameMichal Cieslakiewicz2020-02-034-9/+9
| | | | | | | | Adapt Netgear WNDR3700v2 device identification string to ath79 naming scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config, makefile, init scripts and device tree definition). Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add common definition for Device/tplink-v2Adrian Schmutzler2020-02-022-8/+13
| | | | | | | | | | | | | | | | This adds a shared definition Device/tplink-v2 to common-tp-link.mk. Though currently only one device in ath79 uses it, putting it in the common file seems more organized. The definitions are based on the implementation in ramips target, where a lot of devices is using tplink-v2-* commands already. The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because it's default in Build/tplink-v2-image anyway. While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS, which seems to have been overlooked when adding Archer D50 v1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename tplink-loader-okli to tplink-safeloader-okliAdrian Schmutzler2020-02-022-10/+10
| | | | | | | | | This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli since the latter more accurately describes the combination of tplink-safeloader and loader-okli use there. The old version might be confused with other uses of the okli loader. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename Device/tplink to Device/tplink-v1Adrian Schmutzler2020-02-021-6/+6
| | | | | | | | | As we have tplink-v2-header and tplink-v2-image recipes as well, this patch renames the Device/tplink definition to Device/tplink-v1, as it's using the tplink-v1-* commands. This should provide easier distinction in the future. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti NanoStation Loco M (XW)Roger Pueyo Centelles2020-01-314-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-23 18:45:08 +0000