aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* ath79: rename TL-WR740ND-v4 to TL-WR740N-v4Paul Wassi2019-02-144-7/+7
| | | | | | Give the device the same name it had in ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for Xiaomi Mi Router 4QDavid Bauer2019-02-113-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9561 RAM: 64M DDR2 FLASH: 16M SPI-NOR ETH: 1x WAN - 2x LAN WiFi: QCA9561 3T3R BTN: 1x Reset - 1x WPS LED: 1x Blue - 1x Red - 1x Yellow UART: TX - GND - RX - VCC (From ethernet port) 115200n8 - 3.3V Installation ------------ 1. Connect to the device via UART. 2. Interrupt the U-Boot on power-on by pressing enter when prompted. 3. Connect you computer to one of the routers LAN ports. Assign yourself the IP 192.168.31.10/24. Copy the OpenWRT initramfs image to a tftp server root directory. Rename the image to 'x4q.bin'. 4. Load the initramfs image to the router by executing following command in U-Boot. The image will boot afterwards. > tftpboot 0x81000000 x4q.bin; bootm 5. SCP the sysupgrade-image into '/tmp'. Remember to assign yourself an IP in 192.168.1.0/24 for this step! 6. Install OpenWRT permanently by executing > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: Fix tx queue timeouts during ifupPetr Štetiar2019-02-071-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during network setup[1] which I was able to reproduce easily with following commands: uci set network.lan.ipaddr='192.168.1.20' uci commit network ifup lan Which resulted after some time in: ... WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280 NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out ... Sometimes I wasn't able to use networking anymore, sometimes it was enough to just ifdown/ifup lan and network was backup. On ar71xx it was all working just fine. I've found out, that it was happening because ag71xx_poll() wasn't called, thus the TX queue wasn't emptied. The ag71xx_poll() is being called from napi hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since no interrupts were ever fired again after ag71xx_stop() was called, it was always leading to tx queue timeouts: *** ag71xx_hard_start_xmit() eth0: packet injected into TX queue eth0: raw intr=00000001 TXPS POLL eth0: enable polling mode eth0: processing TX ring, flush=no eth0: disable polling mode, rx=1, tx=1,limit=32 ( `ifup lan done here` ) *** ag71xx_stop() *** ag71xx_open() *** ag71xx_hw_enable() IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready *** ag71xx_hard_start_xmit() eth0: packet injected into TX queue *** ag71xx_hard_start_xmit() eth0: packet injected into TX queue ... WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274 So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and fixed this issue. 1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246 Signed-off-by: Petr Štetiar <ynezz@true.cz> [move ag->link before ag71xx_hw_disable to retain ordering as original] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for TP-LINK Archer C7 v4Oldřich Jedlička2019-02-055-0/+290
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the Qualcomm/Atheros QCA9561 SoC + QCA9880. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction: 1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin and rename it to ArcherC7v4_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
* ath79: add support for TP-Link Archer C2 V3 (AC900)Skirmantas Lauzikas2019-01-275-7/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the TP-link Archer C2 V3 (AC900). Specifications: - CPU: QCA9563 750Mhz - Ram: 64MB (DDR2) - Flash: 8MB (SPI NOR) - Ethernet: 5x 10/100/1000 - Wifi: QCA9563 bgn + QCA9887 an+ac - 9x Leds, 2x buttons Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin via the router Web interface and flash as normal firmware update. Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt> [reorder entries, fix trailing whitespace in dts, add firmware partition compatible string, remove led default off states, use default on state for system led, reuse tplink-safeloader-uimage image build recipe, squash with dynamic partitioning commit, reword commit message, add installation instructions] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath79: add support for Devolo WiFi Pro 1750eDjango Armstrong2019-01-264-1/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3) WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3) BTN: 1x Reset 1x WPS 1x USB eject LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports) Dupont 4 pin header Rear RJ45 serial port non-functional USB: 1x v2.0 Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password previously set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
* ath79: dts: Unify naming of gpio-led nodesPetr Štetiar2019-01-268-8/+8
| | | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> [split up, removed entries where it could clash due to ath9k-leds] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: dts: Unify naming of gpio-keys nodesPetr Štetiar2019-01-2613-13/+13
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* ath79: fix GL.iNet AR300M family GPIOs/LEDsJeff Kletsky2019-01-261-14/+2
| | | | | | | | | | | | | | | | | Change the "status" LED to proper GPIO 12 and "red" naming. Remove GPIO 2 from definition as a USB LED. GPIO 2 is used to control power to the USB socket, not an LED. As such, PWM on the line or typical LED triggers are inappropriate. Users who wish to control the USB power for custom applications can manipulate the GPIO through code, or for example, export it through /sys/class/gpio/export. Runtime-tested:  GL.iNet AR300M-Lite Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* kernel: bump 4.14 to 4.14.95Koen Vandeputte2019-01-241-2/+2
| | | | | | | | | | | | | | Refreshed all patches. Removed superseded patches: - 0400-Revert-MIPS-smp-mt-Use-CPU-interrupt-controller-IPI-.patch Compile-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370), x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370) Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Mathias Kresin <dev@kresin.me> Tested-by: Robert Resch <openwrt@webnmail.de>
* ath79: fix port order for dir 825-c1 and 835-a1Sebastian Kemper2019-01-221-11/+11
| | | | | | | | | | LAN ports 1 and 4 and 2 and 3 are interchanged. Fix this in 02_network so the ports show up in the correct order in luci. The correct ucidef_add_switch line is already present. This commit moves the blocks around to keep alphabetical order. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
* ath79: ag71xx: preserve port mirror flags during swconfig applyMilan Krstic2019-01-221-0/+4
| | | | | | | | The swconfig load operation always triggers 'apply' function which in this driver currently clears port mirroring flags effectively undoing port mirroring configuration. Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
* ath79: add support for devolo WiFi pro 1200iDavid Bauer2019-01-054-0/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1750iDavid Bauer2019-01-054-1/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: merge cases in 02_networkPaul Wassi2019-01-021-16/+6
| | | | | | Merge some duplicate cases in /etc/board.d/02_network Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: align GL-AR750S boardname to other GL.iNet devicesChristoph Krapp2019-01-014-10/+7
| | | | | | As the official device name is GL-AR750S, rename the board accordingly. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: fix case statement in 01_ledsPaul Wassi2019-01-011-0/+1
| | | | | | Fix a missing 'end-of-case' recently introduced in 01_leds Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rework elecom-header recipeMathias Kresin2018-12-311-26/+22
| | | | | | | | Replace the code with a more readable version. Rename the recipe to reflect the real usecase. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix spaces vs. tabsPaul Wassi2018-12-311-3/+3
| | | | | | Fix spaces vs. tabs issues in ath79 and ramips. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: tweak the position of factory partition for wr818Rosy Song2018-12-311-8/+8
| | | | | | | | The 'factory' partition will move to 0x50000-0x60000 in 2019. As the webserver in bootloader is compatible with different mtdlayout, all the users still can upgrade firmware whatever on ath79 or ar71xx. Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ath79: add support for COMFAST CF-E110NRoger Pueyo Centelles2018-12-313-0/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E110N, an outdoor wireless CPE with two Ethernet ports and a 802.11bgn radio. Specifications: - 650/400/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 26 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new want, so a factory reset will be needed: once the new firmware is flashed, perform the factory reset by pushing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing quicker. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Notes: The device is advertised, sold and labeled as "CF-E110N", but the bootloader and the stock firmware identify it as "v2". Acknowledgments: Petr Štetiar <ynezz@true.cz> Sebastian Kemper <sebastian_ml@gmx.net> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [drop unused labels from devicetree source file] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for TP-Link Archer C6 v2Georgi Vlaev2018-12-316-1/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* ath79: add support for EnGenius EWS511APGuan-Hong Lin2018-12-315-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EWS511AP is a wireless managed wall AP with PoE support, based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887. Short specification: - 128MB of RAM - 16 MB of SPI FLASH - 2T2R 2.4 GHz (QCA9531), 802.11b/g/n - 1T1R 5 GHz (QCA9887), 802.11ac/n/a - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED - 1x RESET button - built-in watchdog chipset Flash instruction: From EnGenius firmware to OpenWrt firmware: Original firmware is based on QSDK. Use sysupgrade firmware directly in vendor GUI. Reset to factory default is necessary. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the OpenWrt firmware in the root directory on your computer. 2. Power up EWS511AP. Press 4 and then press any key to enter u-boot. 3. Download OpenWrt firmware (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin" 4. Flash the firmware (ath)> erase 0x9f060000 +f50000 (ath)> cp.b $fileaddr 0x9f060000 $filesize 5. Reboot (ath)> reset Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
* ath79: add status LED on GL.iNet AR300MPaul Wassi2018-12-311-1/+8
| | | | | | This adds the triggers for the status LED of this device. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-316-9/+10
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Add support for TP-Link WR810NPaul Wassi2018-12-315-1/+182
| | | | | | Device specifications given in b23b0fb28b760ce66a8f93d4681c8bd300d75d30 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: Add GL.iNet AR150 LED triggersPaul Wassi2018-12-311-0/+4
| | | | | | | When switching from ar71xx to ath79 the default netdev LED triggers for LAN and WAN got lost. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR150Paul Wassi2018-12-313-4/+4
| | | | | | | This device is called GL-AR150, therefore rename the board to 'gl-ar150' Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for ELECOM WRC-1750GHBK2-I/CINAGAKI Hiroshi2018-12-316-138/+224
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac routers, based on Qualcomm Atheros QCA9563. This commit also includes small fix; use "0x0x03000101" as pll_1000 instead of "0x03000000". Specification: - SoC: Qualcom Atheros QCA9563 - RAM: 128 MB (DDR2) - Flash: 16 MB (SPI-NOR) - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 10/100/1000 Mbps - LED/key: 4x/3x (2x buttons, 1x slide-switch) - UART: through-hole on PCB - Vcc, RX, GND, TX from switch (QCA8337N) side - 115200n8 Flash instruction using factory image: 1. Boot WRC-1750GHBK2-I/C normaly 2. Access to "http://192.168.2.1/" and open firmware upgrade page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Fix UBNT Unifi AC LEDsPaul Wassi2018-12-311-2/+2
| | | | | | | Both LEDs on these devices are ACTIVE_HIGH, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: Fix system LED on TP-Link WR740/741 v4Paul Wassi2018-12-311-1/+1
| | | | | | | The system LED on these devices is ACTIVE_LOW, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for TP-Link TL-WR841N/ND v8Antonio Silverio2018-12-314-0/+175
| | | | | | | | | | | | | | | | | | | CPU: Atheros AR9341 535MHz RAM: 32MB FLASH: 4MiB PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan WiFi: Atheros AR9341 2x2:2 bgn LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill BTN: WPS, WiFi, Reset Installation: Upload the factory image via the vendor-GUI. Signed-off-by: Antonio Silverio <menion@gmail.com> [resolve merge conflicts, squash commits, fix commit title, remove default default off led properties, mark sysupgrade image compatible with the ar71xx version of the board, drop blank lines from dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: use caldata patching for Archer C58/C59David Bauer2018-12-312-4/+1
| | | | | | | | | | | With this commit the TP-Link Archer C58 and Archer C59 use caldata patching in order to set the correct 5GHz MAC-address. Tested on TP-Link Archer C59 v1. For more details see commit 330965b. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for GL.iNet GL-AR750SChristoph Krapp2018-12-314-4/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now this patch adds nor image generation only. NAND image generation is not supportet at the moment. Furtheremore support for the MicroSD port is not implemented as of now. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x switch button, 1x reset button - LED: 3x LEDS (green) - Another LED can be accessed on GPIO 7 if soldered Flash instruction: - Set static ip to 192.168.1.2 - Unplug the power cord - Hold reset button - Plug power back in - Right led will flash 5 times - Release reset button - Browse to 192.168.1.1 - Choose sysupgrade image in NOR-flash section - Press "update nor firmware" - After successful transfer unplug network cable before device restarts Signed-off-by: Christoph Krapp <achterin@googlemail.com> [resolve merge conflicts, rename buttons, use switch input type for mode switch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix OCEDO Koala ethernet configurationDavid Bauer2018-12-301-11/+1
| | | | | | | | | The OCEDO Koala has incorrect PLL settings which result in ~3% packet loss on ethernet connections. Also omit the gmac-configuration as it's incorrect too. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DIR-859 A1Weijie Gao2018-12-307-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Fix wrong TL-WR740N v4 switch port orderEduardo Barros2018-12-291-6/+6
| | | | | | | | | | | Fix the switch port order to have the correct order in LuCI. Fixes: FS#1469 Signed-off-by: Eduardo Barros <geadas@gmail.com> [trim commit title, add a proper commit message, add fixes tag, keep alphabetical order of the blocks] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix Archer A7 v5 5GHz MAC adressDavid Bauer2018-12-291-1/+1
| | | | | | | | Currently all Archer A7 v5 have the same (incorrect) MAC address. The address is currently derived from eth1 which is not present on the QCA9563. Use eth0 to get the correct MAC address. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ubnt-bullet-m-xw: Remove eth1 disabled nodePetr Štetiar2018-12-271-4/+0
| | | | | | It's redundant as eth1 is disabled by default in ath79.dtsi. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Move eth0 mtd-mac-address to the common includePetr Štetiar2018-12-272-2/+4
| | | | | | | It's same for Bullet and Nanostation so far, so let's hope it's going to be the same for other boards sharing the same platform. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Remove pll-data property from eth0 nodePetr Štetiar2018-12-271-1/+0
| | | | | | | | | | | | | | | | | | It's not necessary as it's already defined in ar934x.dtsi to: pll-data = <0x16000000 0x00000101 0x00001616>; And in ar71xx it's currently set to the same values: #define AR934X_PLL_VAL_1000 0x16000000 #define AR934X_PLL_VAL_100 0x00000101 #define AR934X_PLL_VAL_10 0x00001616 And dumping the value from the airOS v6.1.7 has the same value: AR934X_PLL_ETH_XMII_CONTROL_REG 0x1805002C 0x101 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-xw: Add LED aliases for diag and status LED supportPetr Štetiar2018-12-271-1/+8
| | | | | | | | Currently there is no LED signalization for various system states implemented in diag.sh, so this patch adds support for it. Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for devolo WiFi pro 1750cDavid Bauer2018-12-274-1/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button There is also a Micro-B USB-port present but this only seems to be a dummy as the circuit next to it is not present (at least in my unit). It is also not mentioned in the devolo manual. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1200eDavid Bauer2018-12-276-0/+214
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer C7 v5TOCK Chiu2018-12-275-1/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for TP-Link Archer C7 v5, leveraging most effort from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5 but with a different flash layout. Specification: - QCA9563 SoC (750 MHz) - 128 MiB of RAM (DDR2) - 16 MiB of flash (SPI) - 5x 1 Gbps Ethernet (1x WAN + 4x LAN) - 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880 - 10x LED, 2x button - UART header on PCB Flash instructions: 1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin via web interface. Flash instructions using TFTP recovery: 1. Plug PC to one of the LAN ports 2. Set PC to fixed IP address 192.168.0.66 3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in TFTP root directory 4. Turn on the router with the reset button pressed for about 15 secs 5. Release the button and wait about 150 secs to complete flashing Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
* ath79: fix pinmux reg size for QCA955xChristian Lamparter2018-12-241-1/+1
| | | | | | | | The range of pinmux reg property "<0x1804002c 0x40>" for QCA955x SoC does not includes GPIO_FUNCTION register. Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for NEC Aterm WG800HPINAGAKI Hiroshi2018-12-245-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 1T1R (QCA9887) - 4x 10/100/1000 Mbps Ethernet - 8x LEDs, 3x keys (2x buttons, 1x slide-switch) - UART through-hole on PCB (J2) - Vcc, GND, NC, TX, RX from SoC side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WG800HP 2. Connect power cable to WG800HP and turn on it 3. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix pinmux reg value for QCA956xINAGAKI Hiroshi2018-12-241-1/+1
| | | | | | | | | | | | | The range of pinmux reg property "<0x1804002c 0x40>" for QCA956x SoC does not includes GPIO_FUNCTION register. If the device uses "&jtag_disable_pins", this causes the following errors: [ 1.982937] pinctrl-single 1804002c.pinmux: mux offset out of range: 0x40 (0x40) [ 1.990622] pinctrl-single 1804002c.pinmux: could not add functions for pinmux_jtag_disable_pins 64x Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: replace cameo-factory with existing build commandsMathias Kresin2018-12-171-2/+4
| | | | | | | | Use pad-offset and append-string to create the cameo factory images for the D-LINK DIR-825 C1/DIR-835 A1 factory images. Tested-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-12 20:37:04 +0000