aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/patches-5.4
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Arduino YunSungbo Eo2020-07-081-0/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Arduino Yun is a microcontroller development board, based on Atmel ATmega32u4 and Atheros AR9331. Specifications: - MCU: ATmega32U4 - SoC: AR9331 - RAM: DDR2 64MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: SoC internal - Ethernet: 1x 10/100Mbps - USB: 1x 2.0 - MicroSD: 1x SDHC Notes: - Stock firmware is based on OpenWrt AA. - The SoC UART can be accessed only through the MCU. YunSerialTerminal is recommended for access to serial console. - Stock firmware uses non-standard 250000 baudrate by default. - The MCU can be reprogrammed from the SoC with avrdude linuxgpio. Installation: 1. Update U-Boot environment variables to adapt to new partition scheme. > setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000" > setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro" > saveenv 2. Boot into stock firmware normally and perform sysupgrade with sysupgrade image. # sysupgrade -n -F /tmp/sysupgrade.bin Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: Update kernel 5.4 to version 5.4.50Hauke Mehrtens2020-07-042-2/+2
| | | | | | | Run tested: ath79, ipq40xx Build tested: ath79, ipq40xx Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add Mikrotik rb4xx series driversChristopher Hill2020-06-151-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds 3 Mikrotik rb4xx series drivers as follows: rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device that interfaces between the SoC SPI bus and its two children below. rb4xx-gpio: This is the GPIO expander. rb4xx-nand: This is the NAND driver. The history of this code comes in three phases. 1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/. Module-author: Gabor Juhos <juhosg@openwrt.org> Module-author: Imre Kaloz <kaloz@openwrt.org> Module-author: Bert Vermeulen <bert@biot.com> 2. Next several ar71xx patches were applied bringing the code current. commit 7bbf4117c6fe4b764d9d7c62fb2bcf6dd93bff2c Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> commit af79fdbe4af32a287798b579141204bda056b8aa commit 889272d92db689fd9c910243635e44c9d8323095 commit e21cb649a235180563363b8af5ba8296b9ac0baa commit 7c09fa4a7492ca436f2c94bd9a465b7c5bbeed6f Signed-off-by: Felix Fietkau <nbd@nbd.name> 3. Finally a heavy refactor to split the driver into the three new subsystems, and updated to work with the device tree configuration, plus updates and review feedback incorporated Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Christopher Hill <ch6574@gmail.com>
* ath79: phy-ar7200-usb: do not print error on defered initJohann Neuhauser2020-06-031-2/+3
| | | | | | | | | | | This is only a cosmetic correction, as the driver works as expected. However, the error message confuses users about a missing reset definition. On a defered init we don't see the following error message now: [ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* kernel: bump 5.4 to 5.4.43Petr Štetiar2020-06-021-1/+1
| | | | | | | | | | | Refreshed patches, removed upstreamed patch: bcm27xx: 950-0642-component-Silence-bind-error-on-EPROBE_DEFER.patch Run tested: qemu-x86-64 Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: properly insert local mtd partition parsersAdrian Schmutzler2020-05-251-10/+13
| | | | | | | | | | | | | | | | Between 4.19 and 5.4, the kernel moved the partition parsers into the parsers subdirectory. This led to some necessary rebasing of our local patches for parsers, which partially has been performed without caring about where the code was inserted. This commit tries to adjust our local patches so that parsers are inserted at the "proper" positions with respect to alphabetic sorting (if possible). Thus, the commit is cosmetic. While this might look useless now, it will make life easier when adding other parsers in the future or for rebasing on kernel changes. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.41Koen Vandeputte2020-05-141-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: imx6 Runtime-tested on: imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: remove unused TP-Link partition parserDavid Bauer2020-04-271-244/+0
| | | | | | | This parser was added with the target, but no device seems to use it currently, as all partitions are specified in the device-tree. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: move tplinkpart.c parser to patchesAdrian Schmutzler2020-04-241-18/+237
| | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Like for myloader.c in the previous patch, this patch moves tplinkpart.c to the kernel patches, so the code and the kernel includes are at the same location and the path can be adjusted per kernel. While at it, remove some outdated kernel version switches from the C code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: fix include of myloader.o since kernel 5.4Adrian Schmutzler2020-04-241-3/+3
| | | | | | | | | | | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Based on this, the selection of myloader.o in OpenWrt was also moved to that subdirectory, while the Kconfig and our local myloader.c file remained in /drivers/mtd. This resulted in linking errors like the following (on ath25@5.4): make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ... needed by 'drivers/mtd/parsers/built-in.a'. Stop. make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2 make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2 Since myloader.c is not too big, this patch moves it to the kernel patches, allowing to adjust the path for kernel 5.4 and keeping Makefiles and file paths better in sync. Other patches have been refreshed accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add QCA9550 reset sequenceDavid Bauer2020-04-171-0/+130
| | | | | | | | | | | | | | | | | The QCA9550 family of SoCs have a slightly different reset sequence compared to older chips. Normally the bootloader performs this sequence, however some bootloader implementation expect the operating system to clear the reset. Also get the PCIe resets from OF to support the second RC of the QCA9558. This is required for the AVM FRITZ!WLAN Repeater 1750E to work, as EVA leaves the PCIe bus in reset. Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 5.4 to 5.4.32Petr Štetiar2020-04-141-4/+2
| | | | | | | | | | | Refreshed patches, removed upstreamed patches: generic: 746-stable-net-dsa-mt7530-fix-null-pointer-dereferencing-in-por.patch Run tested: qemu-x86-64, apalis Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add read support using spi-memLuiz Angelo Daros de Luca2020-04-141-0/+70
| | | | | | | | | | | | | | | | Reimplements read optimization on top of spi-mem. Similar to what 461-spi-ath79-add-fast-flash-read.patch used to do with the dropped flash read interface. It accelerate only fast-read op reading flash directly from memory mapped region. 'm25p,fast-read' must be set in order to use the new spi-mem. It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1) while no speed improvement was noticed on newer devices like (tplink,archer-c7-v2). Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* kernel: bump 5.4 to 5.4.28Petr Štetiar2020-03-282-16/+16
| | | | | | | | | | | | | | | | | | | | Changelog since 5.4.24 mentions CVE-2019-19769, CVE-2020-8648, CVE-2020-8649 and CVE-2020-8647. Removed upstreamed: generic: 507-v5.6-iio-chemical-sps30-fix-missing-triggered-buffer-depe.patch generic: 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch bcm27xx: 950-0435-ASoC-pcm512x-Fix-unbalanced-regulator-enable-call-in.patch ipq806x: 701-stmmac-fix-notifier-registration.patch lantiq: 002-pinctrl-falcon-fix-syntax-error.patch octeontx: 0002-net-thunderx-workaround-BGX-TX-Underflow-issue.patch Run tested: apu2, qemu-x86-64, apalis, a64-olinuxino, nbg6617 Build tested: sunxi/a53, imx6, x86/64, ipq40xx Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: use downstream ag71xx for Kernel 5.4David Bauer2020-03-134-175/+28
| | | | | | | | | | | | | | | | | | | The ag71xx driver from Linux 5.4 currently has various shortcomings when used with OpenWrt compared to our downstream version. For example, the upstream driver does not support modifying the ethernet clock and configuring RGMII delays on the MAC side. While we should certainly switch to the upstream driver, the amount of necessary patches would make it cumbersome to work with. It's also highly likely we won't be able to finish patching the upstream driver in time for a Linux 5.4 release. Tested on Siemens WS-AP3610. CC: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David Bauer <mail@david-bauer.net> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: re-add accidentally dropped patch to kernel 5.4Daniel Golle2020-03-064-14/+281
| | | | | | | | Patch 0061-tty-serial-ar933x-uart-rs485-gpio.patch wasn't included when adding support for kernel 5.4. Re-add it and refresh patches. Fixes: 53ab9865c2 ("ath79: add support for kernel 5.4") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* spi: ath79: remove spi-master setup and cleanup assignmentDavid Bauer2020-02-291-0/+28
| | | | | | | | | | | This removes the assignment of setup and cleanup functions for the ath79 target. Assigning the setup-method will lead to 'setup_transfer' not being assigned in spi_bitbang_init. Also drop the redundant cleanup assignment, as this also happens in spi_bitbang_init. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Make upstream ag71xx driver workHauke Mehrtens2020-02-283-0/+175
| | | | | | | | * Fix some bugs in the driver * Add missing clock and reset references in dts * Rename mdio-bus to mdio so the driver find it Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add support for kernel 5.4David Bauer2020-02-2832-0/+3543
Signed-off-by: David Bauer <mail@david-bauer.net> [refreshed] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> * Sync the patches with the changes done for kernel 4.19 * Use KERNEL_TESTING_PATCHVER * Refresh the configuration * Fix multiple compile bugs in the patches * Only add own ag71xx files for kernel 4.19 and use upstream version for 5.4. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 19:58:19 +0000