aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/patches-4.19
Commit message (Collapse)AuthorAgeFilesLines
* kernel: Update kernel 4.19 to version 4.19.138Hauke Mehrtens2020-08-101-2/+2
| | | | | | Compile and run tested on lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add support for Arduino YunSungbo Eo2020-07-081-0/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Arduino Yun is a microcontroller development board, based on Atmel ATmega32u4 and Atheros AR9331. Specifications: - MCU: ATmega32U4 - SoC: AR9331 - RAM: DDR2 64MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: SoC internal - Ethernet: 1x 10/100Mbps - USB: 1x 2.0 - MicroSD: 1x SDHC Notes: - Stock firmware is based on OpenWrt AA. - The SoC UART can be accessed only through the MCU. YunSerialTerminal is recommended for access to serial console. - Stock firmware uses non-standard 250000 baudrate by default. - The MCU can be reprogrammed from the SoC with avrdude linuxgpio. Installation: 1. Update U-Boot environment variables to adapt to new partition scheme. > setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000" > setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro" > saveenv 2. Boot into stock firmware normally and perform sysupgrade with sysupgrade image. # sysupgrade -n -F /tmp/sysupgrade.bin Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: Update kernel 4.19 to version 4.19.131Hauke Mehrtens2020-07-042-3/+3
| | | | | | | | | | | | | Fixes: - CVE-2020-10757 The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was backported which needed some adaptations to other code. Run tested: ath79 Build tested: ath79 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add Mikrotik rb4xx series driversChristopher Hill2020-06-151-0/+69
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds 3 Mikrotik rb4xx series drivers as follows: rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device that interfaces between the SoC SPI bus and its two children below. rb4xx-gpio: This is the GPIO expander. rb4xx-nand: This is the NAND driver. The history of this code comes in three phases. 1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/. Module-author: Gabor Juhos <juhosg@openwrt.org> Module-author: Imre Kaloz <kaloz@openwrt.org> Module-author: Bert Vermeulen <bert@biot.com> 2. Next several ar71xx patches were applied bringing the code current. commit 7bbf4117c6fe4b764d9d7c62fb2bcf6dd93bff2c Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> commit af79fdbe4af32a287798b579141204bda056b8aa commit 889272d92db689fd9c910243635e44c9d8323095 commit e21cb649a235180563363b8af5ba8296b9ac0baa commit 7c09fa4a7492ca436f2c94bd9a465b7c5bbeed6f Signed-off-by: Felix Fietkau <nbd@nbd.name> 3. Finally a heavy refactor to split the driver into the three new subsystems, and updated to work with the device tree configuration, plus updates and review feedback incorporated Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Christopher Hill <ch6574@gmail.com>
* ath79: phy-ar7200-usb: do not print error on defered initJohann Neuhauser2020-06-031-2/+3
| | | | | | | | | | | This is only a cosmetic correction, as the driver works as expected. However, the error message confuses users about a missing reset definition. On a defered init we don't see the following error message now: [ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* kernel: bump 4.19 to 4.19.122Koen Vandeputte2020-05-121-1/+2
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 551-loop-Better-discard-support-for-block-devices.patch Fixed: - CVE-2020-11884 - CVE-2020-12114 - CVE-2019-3016 - CVE-2020-11669 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: remove unused TP-Link partition parserDavid Bauer2020-04-271-250/+0
| | | | | | | This parser was added with the target, but no device seems to use it currently, as all partitions are specified in the device-tree. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: move tplinkpart.c parser to patchesAdrian Schmutzler2020-04-241-0/+225
| | | | | | | | | | | | | Between 4.19 and 5.4, mtd parsers have been moved to "parsers" subdirectory. Like for myloader.c in the previous patch, this patch moves tplinkpart.c to the kernel patches, so the code and the kernel includes are at the same location and the path can be adjusted per kernel. While at it, remove some outdated kernel version switches from the C code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add QCA9550 reset sequenceDavid Bauer2020-04-171-0/+130
| | | | | | | | | | | | | | | | | The QCA9550 family of SoCs have a slightly different reset sequence compared to older chips. Normally the bootloader performs this sequence, however some bootloader implementation expect the operating system to clear the reset. Also get the PCIe resets from OF to support the second RC of the QCA9558. This is required for the AVM FRITZ!WLAN Repeater 1750E to work, as EVA leaves the PCIe bus in reset. Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.19 to 4.19.115Koen Vandeputte2020-04-164-21/+19
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch - 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch Fixes: - CVE-2020-8647 - CVE-2020-8648 (potentially) - CVE-2020-8649 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add read support using spi-memLuiz Angelo Daros de Luca2020-04-141-0/+70
| | | | | | | | | | | | | | | | Reimplements read optimization on top of spi-mem. Similar to what 461-spi-ath79-add-fast-flash-read.patch used to do with the dropped flash read interface. It accelerate only fast-read op reading flash directly from memory mapped region. 'm25p,fast-read' must be set in order to use the new spi-mem. It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1) while no speed improvement was noticed on newer devices like (tplink,archer-c7-v2). Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* kernel: bump 4.19 to 4.19.106Koen Vandeputte2020-02-242-17/+13
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0786-leds-pca963x-Fix-open-drain-initialization.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.105Koen Vandeputte2020-02-242-3/+3
| | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2013-1798 - CVE-2019-3016 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* serial: ar933x_uart: add rs485 supportDaniel Golle2020-02-211-0/+271
| | | | | | | | | Add support for RS485 tranceiver with transmit/receive switch hooked to a RTS GPIO pin. Use the 'rts-gpios' and 'rs485-rts-active-low' properties as described in devicetree/bindings/serial/rs485.yaml. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: backport phy reset-controller patchesDavid Bauer2020-02-162-0/+151
| | | | | | | | | | The Siemens WS-AP3610 asserts reset to the ethernet PHY with the reset-register. Backport the necessary patches to de-assert reset when probing the PHY. These patches can be dropped when using kernel 5.4. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: restore pin state on probe for ar934x-spiChuanhong Guo2020-02-101-5/+11
| | | | | | | | | | | | If bootloader doesn't terminate its last spi operation properly before starting kernel, our first transfer in kernel becomes a continuous transfer to that request instead of a new one. Fix this flaw by restoring IOC register, which restored all pin state to default. Fixes: ebf0d8dade ("ath79: add new ar934x spi driver") Reported-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Atheros AR934x HS UARTDaniel Golle2020-02-071-0/+52
| | | | | | | | | AR934x chips also got the 'old' qca,ar9330-uart in addition to the 'new' ns16550a compatible one. Add support for UART1 clock selector as well as device-tree bindings in ar934x.dtsi to make use of that uart. Reported-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDEDaniel Golle2020-02-071-0/+64
| | | | | | | | | | | | | | | | On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x does not do any harm, so just set them unconditionally. Tested-by: Chuanhong Guo <gch981213@gmail.com Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add new ar934x spi driverChuanhong Guo2020-02-062-0/+338
| | | | | | | | | | | A new shift mode was introduced since ar934x which has a way better performance than current bitbang driver and can handle higher spi clock properly. This commit adds a new driver to make use of this new feature. This new driver has chipselect properly configured and we don't need cs-gpios hack in dts anymore. Remove them. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: bump 4.19 to 4.19.101Koen Vandeputte2020-02-041-1/+1
| | | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14896 - CVE-2019-14897 Remove upstreamed: - 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch - 950-0202-staging-bcm2835-camera-fix-module-autoloading.patch - 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.98Koen Vandeputte2020-01-244-6/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: allow to override AR8033 SGMII aneg statusDavid Bauer2020-01-231-0/+16
| | | | | | | | | | | | | In order to make the QCA955x SGMII workaround work, the unsuccessful SGMII autonegotiation on the AR8033 should not block the PHY state-machine. Otherwise, the ag71xx driver never becomes aware of the copper-side link-establishment and the workaround is never executed. Signed-off-by: David Bauer <mail@david-bauer.net> [remove one trailing whitespace per file] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add QCA955x SGMII link loss workaroundDavid Bauer2020-01-231-0/+91
| | | | | | | | | | | | | | | | This commit adds a workaround for the loss of the SGMII link observed on the QCA955x generation of SoCs. The workaround originates part from the U-Boot source code, part from the implementation from AVM found in the GPL tarball for the AVM FRITZ!WLAN Repeater 450E. The bug results in a stuck SGMII link between the PHY device and the SoC side. This has only been observed with the Atheros AR8033 PHY and most likely all devices using such combination are affected. It is worked around by reading a hidden SGMII status register and issuing a SGMII PHY reset until the link becomes useable again. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.19 to 4.19.95Koen Vandeputte2020-01-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: phy-ar7200-usb: adapt old behavior of arch/mips/ath79/dev-usb.cJohann Neuhauser2020-01-151-6/+18
| | | | | | | | | | | | Do not put usb-phy into reset if clearing the usb-phy reset or setting the suspend_override has failed. Reorder (de)asserts like in arch/mips/ath79/dev-usb.c. Add an optional reset_control "usb-phy-analog", which is needed for ar934x SoCs like in the old mach-driver arch/mips/ath79/dev-usb.c. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: drop obsolete ehci hacksBjørn Mork2020-01-051-103/+0
| | | | | | | There's nothing enabling these hacks in ath79, so drop the redundant patches. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ath79: Remove mtd cfi_cmdset_0002 status check patchesTokunori Ikegami2020-01-051-62/+0
| | | | | | | | | | | | | Currently the patch only changes break to use goto statement instead. But not necessary acutually since the ret value checked after the for loop. So it is okay for the break case before changed by the patch also. This patch only reverts the following commit partially. https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e7 Note: The changes are mainly applied into the linux kernel upstream. Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.93Hauke Mehrtens2020-01-051-4/+4
| | | | | | | | | | | | | | Refreshed all patches. The patch hack-4.19/550-loop-better-discard-for-block-devices.patch was replaced with an new version of the patch from: https://lore.kernel.org/patchwork/patch/1153625/ https://lore.kernel.org/patchwork/patch/1153626/ Compile-tested on: ipq40xx, lantiq Runtime-tested on: ipq40xx, lantiq Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.19 to 4.19.88Koen Vandeputte2019-12-101-1/+1
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0004-boot-sq201-from-sda1.patch - 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch - 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch Altered patches: - 0011-ARM-dts-Fix-up-SQ201-flash-access.patch - 400-mtd-add-rootfs-split-support.patch - 0101-pci-mediatek-backport-fix-pcie.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.86Koen Vandeputte2019-11-291-4/+4
| | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch - 0005-mtd-physmap_of-Move-custom-initialization.patch Remove upstreamed: - 0001-pinctrl-gemini-Mask-and-set-properly.patch - 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: disable delays on AT803X config initDavid Bauer2019-10-271-0/+27
| | | | | | | | | | | | | | Until upstream commit 6d4cd041f0af("net: phy: at803x: disable delay only for RGMII mode"), delays were not disabled on driver probe for the Atheros AR803x PHYs, although the RX delay is enabled on soft and hard reset. In addition, the TX delay setting is retained on soft-reset. This patch disables both delays on config init to align the behavior with kernel 5.1 and higher. It can be safely dropped with kernel 5.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add AR934x NAND Flash Controller driverMichal Cieslakiewicz2019-10-201-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch contains updated driver for Atheros NAND Flash Controller written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc'). ath79 version has adapted to work with kernel 4.19 and Device Tree. It has also been renamed to 'ar934x-nand' to avoid confusion with Near-Field Communication technology. Controller is present on Atheros AR934x SoCs and required for accessing internal flash storage on routers like Netgear WNDR4300. This port preserves all NAND programming code while moving platform configuration to Device Tree and replacing some kernel functions marked for retirement by 4.19. Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section). Most important changes to ar71xx version are: * old kernel sections of code removed * 'bool swap_dma' provided by platform data is now set by boolean DT property 'qca,nand-swap-dma' * board-supplied (mach-*.c code) platform data removed - its elements become either unused, redundant or replaced by DT methods (like reset) * IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore * calls to deprecated nand_scan_ident() + nand_scan_tail() function pair replaced by using recommended nand_scan() with attach_chip() callback * ECC is set to hardware by default, can be overriden by standard DT 'nand-ecc-*' properties (software Hamming or BCH are other options) This driver has been successfully tested on Netgear WNDR4300 running experimental ath79 OpenWrt master branch. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> [add reset control] Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.19 to 4.19.76Koen Vandeputte2019-10-041-12/+10
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 403-mtd_fix_cfi_cmdset_0002_status_check.patch Compile-tested on: ath79, cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.75Koen Vandeputte2019-09-241-2/+2
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14814 - CVE-2019-14815 - CVE-2019-14816 - CVE-2019-14821 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: fix FIS partition detection for 4.19 kernelTomasz Maciej Nowak2019-09-011-0/+44
| | | | | | | | | When bumping to 4.19 the patch responsible for scaning flash for FIS partition got left out. Without it devices with RedBoot bootloader using automatic partitions detection in dts won't boot with the new kernel. Fixes: 3771176 ("ath79: add support for linux 4.19") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* kernel: bump 4.19 to 4.19.52Koen Vandeputte2019-06-183-4/+4
| | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-11479 - CVE-2019-11478 - CVE-2019-11477 Also fix a malformed patch issue caught during refresh. It was caused by removing a whitespace without altering the index values in a patch which alters a patch. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Fixes: cf6526249298 ("kernel: bump 4.19 to 4.19.51") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.50Koen Vandeputte2019-06-122-3/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.44Koen Vandeputte2019-05-211-1/+1
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.42Koen Vandeputte2019-05-131-1/+1
| | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch - 400-v5.2-leds-trigger-netdev-fix-refcnt-leak-on-interface-ren.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.35Koen Vandeputte2019-04-222-3/+3
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-3887 New symbol: - CONFIG_LDISC_AUTOLOAD Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.34Koen Vandeputte2019-04-082-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed: - 030-PCI-dwc-skip-MSI-init-if-MSIs-have-been-explicitly-d.patch Altered: - 366-netfilter-nf_flow_table-clean-up-and-fix-dst-handlin.patch - 650-netfilter-add-xt_OFFLOAD-target.patch - 662-remove_pfifo_fast.patch - 332-arc-add-OWRTDTB-section.patch - 100-clocksource-drivers-arch_timer-Workaround-for-Allwin.patch - 702-phy_add_aneg_done_function.patch New symbols: - ARC_IRQ_NO_AUTOSAVE - SUN50I_ERRATUM_UNKNOWN1 Compile-tested: cns3xxx, imx6, sunxi Runtime-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for linux 4.19Chuanhong Guo2019-03-2439-0/+6824
The following patches are dropped because they are merged upstream: -0001-tty-serial-drop-QCA-pecific-SoC-symbols.patch -0006-usb-drop-deprecated-symbols.patch -0009-MIPS-ath79-add-lots-of-missing-registers.patch -0010-MIPS-ath79-add-support-for-QCA953x-QCA956x-TP9343.patch -0014-MIPS-ath79-finetune-cpu-overrides.patch -0015-MIPS-ath79-enable-uart-during-early_prink.patch -0016-MIPS-ath79-get-PCIe-controller-out-of-reset.patch This patch is dropped due to the introduction of spi-mem framework: -461-spi-ath79-add-fast-flash-read.patch Thank to Michael Marley @mamarley for his work on this patch: -910-unaligned_access_hacks.patch Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [synchronized kernel config with make kernel_oldconfig] Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 10:14:10 +0000