| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
On Mikrotik SPI NOR devices, the firmware partition must be erased when
flashing from stock firmware, otherwise leftover bits (in particular a
kernel signature) can trigger a boot loop.
When booted from initramfs (the only way to install OpenWRT on these
devices), this patch unconditionally erases the firmware partition in
the do_upgrade() stage for all supported SPI NOR devices.
This is forward-ported from ed49d0876 and 20452a8db
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The MikroTik SXT Lite5 (product code RBSXT5nDr2, also SXT 5nD r2) is
an outdoor 5GHz CPE with a 16 dBi integrated antenna built around the
Atheros AR9344 SoC. It is based on the "sxt5n" board platform.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 128 MB NAND
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 6 user-controllable LEDs:
· 1x power (blue)
· 1x wlan (green)
· 4x rssi (green)
- 1 GPIO-controlled buzzer
See https://mikrotik.com/product/RBSXT5nDr2 for more details.
Notes:
The device was already supported in the ar71xx target. There, the
Ethernet port was handled by GMAC1. Here in ath79 it is handled by
GMAC0, which allows to get link information (loss, speed, duplex) on
the eth0 interface.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Acknowledgments:
Michael Pratt (@mpratt14) for helping on the network settings.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, use mikrotik LED label prefix, make names consistent,
add reg for bootloader2, use led_user for boot indication etc.,
minor cosmetic changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The MikroTik RouterBOARD 921GS-5HPacD-15s (mANTBox 15s) is an outdoor
antenna for 5 GHz with an built-in router. This ports the board from
ar71xx.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9892 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- NAND storage detection
- Ethernet
- Wireless
- 1x user LED (blinks during boot, sysupgrade)
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation (untested):
- Boot initramfs image via TFTP and then flash sysupgrade image
As the embedded RB921-pcb is a stripped down version of the RB922 this patch
adds a common dtsi for this series and includes this to the final dts-files.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[move ath10k-leds closer to ath10k definition in DTS files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the MikroTik RouterBOARD RB493G, ported
from the ar71xx target.
See https://routerboard.com/RB493G for details
Specification:
- SoC Qualcomm Atheros AR7161
- RAM: 256 MiB
- Storage: 128MiB NAND
- Ethernet: 9x 1000/100/10 Mbps
- USB 1x 2.0 / 1.0 type A
- PCIe: 3x Mini slot
- MicroSD slot
Working:
- Board/system detection
- Ethernet
- SPI
- NAND
- LEDs
- USB
- Sysupgrade
Enabled (but untested due to lack of hardware):
- PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed
Installation methods:
- tftp boot initramfs image, scp then flash via "sysupgrade -n"
- nand boot existing OpenWrt, scp then flash via "sysupgrade -n"
Notes:
- initramfs image will not work if uncompressed image size over ~8.5Mb
- The "rb4xx" drivers have been enabled
Signed-off-by: Christopher Hill <ch6574@gmail.com>
|
| |
|
|
|
|
|
| |
With the implementation of a sysfs interface to access WLAN data, this
target no longer needs a special wrapper to extract caldata.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
|
| |
|
|
|
|
|
|
|
|
| |
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_nand().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
By that, BOARD_NAME is obsolete now for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.
MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.
Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.
Tested on the RB922 board and the wAP AC router.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
|
