aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/image
Commit message (Collapse)AuthorAgeFilesLines
* ath79: enable forceless sysupgrade from ar71xx on fritz300eAdrian Schmutzler2020-02-131-0/+1
| | | | | | | This adds the ar71xx board name to the SUPPORTED_DEVICES on ath79, so forceless sysupgrade on this device becomes possible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WA830RE v1Christian Buschau2020-02-111-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This ports support for the TL-WA830RE v1 range extender from ar71xx to ath79. Specifications: - SOC: Atheros AR7240 - CPU: 400MHz - Flash: 4 MiB (Spansion S25FL032P) - RAM: 32 MiB (Zentel A3S56D40FTP-G5) - WLAN: Atheros AR9280 bgn 2x2 - Ethernet: 1 port (100M) Flash instructions: - install from u-boot with tftp (requires serial access) > setenv ipaddr a.b.c.d > setenv serverip e.f.g.h > tftpboot 0x80000000 \ openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin > erase 0x9f020000 +0x3c0000 > cp.b 0x80000000 0x9f020000 0x3c0000 > bootm 0x9f020000 - flash factory image from OEM WebUI - sysupgrade from ar71xx image The device seems to be a clone of the following devices not yet added to ath79: - tl-wa701nd-v1 - tl-wa730re-v1 - tl-wa801nd-v1 - tl-wa901nd-v1 Signed-off-by: Christian Buschau <christian.buschau@mailbox.org> [make use of ar7240_tplink.dtsi, add note about clones] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for COMFAST CF-E560ACAugust Huber2020-02-031-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the COMFAST CF-E560AC, an ap143 based in-wall access point. Specifications: - SoC: Qualcomm Atheros QCA9531 - RAM: 128 MB DDR2 (Winbond W971GG6SB-25) - Storage: 16 MB NOR (Winbond 25Q128JVSO) - WAN: 1x 10/100 PoE ethernet (48v) - LAN: 4x 10/100 ethernet - WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM - WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM - USB: one external USB2.0 port - UART: 3.3v, 2.54mm headers already populated on board - LED: 7x external - Button: 1x external - Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod) MAC addressing: - stock LAN *:40 (label) WAN *:41 5G *:42 2.4G *:4a - flash (art partition) 0x0 *:40 (label) 0x6 *:42 0x1002 *:41 0x5006 *:43 This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and 0x5006, however the vendor firmware only reads from art:0x0 for the LAN interface and then increments in 02_network. They also jump 8 addresses for the second wifi interface (2.4 GHz). This behavior has been duplicated in the DTS and ath10k hotplug to align addresses with the vendor firmware v2.6.0. Recovery instructions: This device contains built-in u-boot tftp recovery. 1. Configure PC with static IP 192.168.1.10/24 and tftp server. 2. Place desired image at /firmware_auto.bin at tftp root. 3. Connect device to PC, and power on. 4. Device will fetch flash from tftp, flash and reboot into new image. Signed-off-by: August Huber <auh@google.com> [move jtag_disable_pins, remove unnecessary statuses in DTS, remove duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: WNDR3700 v2: add dash before version in device nameMichal Cieslakiewicz2020-02-031-3/+3
| | | | | | | | Adapt Netgear WNDR3700v2 device identification string to ath79 naming scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config, makefile, init scripts and device tree definition). Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add common definition for Device/tplink-v2Adrian Schmutzler2020-02-022-8/+13
| | | | | | | | | | | | | | | | This adds a shared definition Device/tplink-v2 to common-tp-link.mk. Though currently only one device in ath79 uses it, putting it in the common file seems more organized. The definitions are based on the implementation in ramips target, where a lot of devices is using tplink-v2-* commands already. The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because it's default in Build/tplink-v2-image anyway. While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS, which seems to have been overlooked when adding Archer D50 v1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename tplink-loader-okli to tplink-safeloader-okliAdrian Schmutzler2020-02-022-10/+10
| | | | | | | | | This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli since the latter more accurately describes the combination of tplink-safeloader and loader-okli use there. The old version might be confused with other uses of the okli loader. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename Device/tplink to Device/tplink-v1Adrian Schmutzler2020-02-021-6/+6
| | | | | | | | | As we have tplink-v2-header and tplink-v2-image recipes as well, this patch renames the Device/tplink definition to Device/tplink-v1, as it's using the tplink-v1-* commands. This should provide easier distinction in the future. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti NanoStation Loco M (XW)Roger Pueyo Centelles2020-01-311-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add support for GL.iNet 6408/6416 (GL.iNet V1)Adrian Schmutzler2020-01-291-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This ports the GL.iNet 6408/6416 from ar71xx. The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with more DRAM/Flash and console/GPIO header in the same small form-factor. Specifications: - SoC: Atheros AR9331 - CPU: 400 MHz - Flash: 8/16 MiB - RAM: 64 MiB - WiFi: 2.4 GHz b/g/n (SoC) - Ethernet: 2x 100M ports (LAN/WAN) - USB: 1x 2.0 The difference between 6408 and 6416 is just the flash size. It looks like only the 16 MiB version has been advertised, while the 6408 is a modified version. There are also 1-port versions sold by third parties. Installation: Install the sysupgrade image via stock firmware GUI or upload it via uboot (web-based). The device will be available at 192.168.1.1. Attention: In ar71xx, the same board name is used for both flash versions. So, please make sure you flash the correct ath79 image when upgrading. This has been device-tested on a GL.iNet 6416. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix SUPPORTED_DEVICES not matching ar71xx board namesAdrian Schmutzler2020-01-234-12/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: move lzma-loader to the end of available RAMAdrian Schmutzler2020-01-232-3/+2
| | | | | | | | | | | | | | | | | | | | | In certain cases, the uncompressed initramfs image will overwrite the lzma-loader, which is currently only 10 MB away from kernel image start. To prevent this, change LZMA_TEXT_START to 24 MB, so loader and compressed image have 8 MB at the end of RAM and uncompressed image has 24 MB available. This is only enabled for ath79 at the moment, as there we can be sure that all devices have 32+ MB RAM and TARGET_INITRAMFS_COMPRESSION_LZMA is not enabled there. Despite, since lzma-loader is currently build specifically for ath79 anyway, there is no need to re-specify LOADADDR and LZMA_TEXT_START in image/Makefile, so the values are set directly in image/lzma-loader/Makefile and the overwrite in image/Makefile is removed. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for MikroTik RouterBOARD wAP G-5HacT2HnDRoger Pueyo Centelles2020-01-232-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet port. See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info. Specifications: - SoC: Qualcomm Atheros QCA9556 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive PoE in Working: - Board/system detection - Sysupgrade - Serial console - Ethernet - 2.4 GHz radio - 5 GHz radio and LED - Reset button Not working/Unsupported: - 2.4 GHz LED - AP/CAP LED - ZT2046Q SPI temperature and voltage sensor This adds the basic features for supporting MikroTik devices: - a common recipe for mikrotik images in common-mikrotik.mk - support for minor (MikroTik NOR) split firmware (only for generic subtarget so far) Acknowledgments: Robert Marko <robimarko@gmail.com> Andrew Cameron <apcameron@softhome.net> Koen Vandeputte <koen.vandeputte@ncentric.com> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-221-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Stock firmware uses label MAC address for WiFi and same with local bit set for ethernet. Since this is difficult to reproduce with the toolset of OpenWrt, we just keep both ethernet and WiFi to the same address here. This is the first tiny device with tplink-safeloader in ath79. Firmware partition is only 3648k and thus even smaller than for the tplink-4m(lzma) devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WA850RE v1Adrian Schmutzler2020-01-221-0/+11
| | | | | | | | | | | | | | | | | | | | | | This ports support for the TL-WA850RE v1 range extender from ar71xx to ath79. Specifications: Board: AP123 / AR9341 rev. 3 Flash/RAM: 4/32 MiB CPU: 535 MHz WiFi: 2.4 GHz b/g/n Ethernet: 1 port (100M) Flashing instructions: Upload the factory image via the vendor firmware upgrade option. Recovery: Note that this device does not provide TFTP via ethernet like many other TP-Link devices do. You will have to open the case if you require recovery beyond failsafe. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove usused TPLINK_BOARD_NAME variable for DEVICE_VARSAdrian Schmutzler2020-01-211-1/+1
| | | | | | | | | | | | | | TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time ago (7d6c63d87542: "build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target at all. TPLINK_BOARD_NAME seems to have been introduced into ath79 target only by mistake. It has never been used. Remove it. Fixes: 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-MR6400Enrico Mioso2020-01-211-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | This device is an LTE router supported in ar71xx so far. As per original commit, hardware specifications (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Flashing instructions: You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Known issues: - LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround. - eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx) Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [several adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Filip Moc <lede@moc6.cz>
* ath79: fix SUPPORTED_DEVICES for WNDR4300 and WNDR3700v4Michal Cieslakiewicz2020-01-211-2/+0
| | | | | | | | | | Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300 routers breaks sysupgrade image compatibility with ar71xx builds. Therefore, SUPPORTED_DEVICES variable has to be removed for both devices from target makefile. Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4500 v3Michal Cieslakiewicz2020-01-151-0/+11
| | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4500v3. Router is very similar to WNDR4300v2 and is based on the same PCB. Information gathered from various Internet sources (including https://patchwork.ozlabs.org/patch/809227/) shows following differences to WNDR4300v2: * two USB 2.0 ports with separate LEDs * USB LEDs soldered to secondary pads * WPS and RFKILL buttons soldered to secondary pads * described as N900 device with 3x3:3 MIMO for 2.4GHz radio * power supply requirement is DC 12V 2.5A * vendor HW ID suffix differs in one digit * bigger chassis Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4300 v2Michal Cieslakiewicz2020-01-151-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4300v2. Specification ============= * Description: Netgear WNDR4300 v2 * Loader: U-boot * SOC: Qualcomm Atheros QCA9563 (775 MHz) * RAM: 128 MiB * Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND - NOR: U-boot binary: 256 KiB - NOR: U-boot environment: 64 KiB - NOR: ART Backup: 64 KiB - NOR: Config: 64 KiB - NOR: Traffic Meter: 64 KiB - NOR: POT: 64 KiB - NOR: Reserved: 1408 KiB - NOR: ART: 64 KiB - NAND: Firmware: 25600 KiB (see notes for OpenWrt) - NAND: Language: 2048 KiB - NAND: mtdoops Crash Dump: 128 KiB - NAND: Reserved: 103296 KiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Important Notes =============== 0. NOR Flash (2 MiB) is not touched by OpenWrt installation. 1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows: all space is split between 4 MiB kernel and 124 MiB UBI areas; vendor partitions (language and mtdoops) are removed; kernel space size can be further expanded if needed; maximum image size is set to 25600k for compatibility reasons and can also be increased. 2. CPU clock is 775 MHz, not 750 MHz. 3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI device ID 0xabcd. For ath9k driver to load successfully, this is overriden in DTS with correct value for this chip, 0x0033. 4. RFKILL button is wired to AR9580 pin 9 which is normally disabled by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore 'qca,gpio-mask=<0xf6ff>' hack must be used for button to work properly. 5. USB port is always on, no GPIO for 5V power control has been identified. Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: WNDR4300: increase kernel partition to 4MMichal Cieslakiewicz2020-01-151-1/+1
| | | | | | | | | Increase kernel partition from 2 MiB to 4 MiB for Netgear WNDR routers with NAND flash. Change affects following devices: * Netgear WNDR3700 v4 * Netgear WNDR4300 Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for D-Link DIR-505David Bauer2020-01-151-0/+10
| | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the D-Link DIR-505, previously supported in ar71xx. Hardware -------- SoC: Atheros AR9330 FLASH: 8M SPI-NOR RAM: 64M WIFI: 1T1R 1SS Atheros AR9330 LED: Power green, Status red BTN: WPS, Reset Installation ------------ Currently, installation is only possible by sysupgrading from an earlier OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the original bootloader from D-Link on my device anymore, so i cannot test the factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: GL-AR750S (NOR/NAND): limit factory.img kernel size to 2 MBJeff Kletsky2020-01-151-1/+4
| | | | | | | | | | | | | | | | The present U-Boot for GL-AR750S has a limit of 2 MB for kernel size. While sysupgrade can manage kernels up to the present limit of 4 MB, directly flashing a factory.img with a kernel size greater than 2 MB through U-Boot will result in an unbootable device. This commit uses the newly-introduced check-kernel-size build operation to prevent the output of factory.img when the kernel exceeds 2 MB in size, yet permits output of sysupgrade.img as long as the kernel is within KERNEL_SIZE := 4096k Cc: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: wlr-7100: use ath10k-ct smallbuffers package variantTomasz Maciej Nowak2020-01-151-1/+1
| | | | | | | | The memory hacks got removed from ath10k with 1e27bef ("mac80211: remove ath10k_pci memory hacks"). As this device has low amount of RAM, switch to ath-10k-ct small buffers variant, to avoid the OOM Reaper. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add support for Ubiquiti EdgeSwitch/ToughSwitch 5XPTobias Schramm2020-01-141-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE out on all five ports. Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: ar8327 USB: 1x USB 2.0 Ethernet: 5x GbE, 1x FE Installation of the firmware is possible either via serial + tftpboot or the factory firmware update function via webinterface. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the five switch ports. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: ``` | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ ``` Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [remove ubnt,sw compatible - fix spelling - wrap commit message - remove superfluous phy-mode property] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Ubiquiti ToughSwitch/EdgeSwitch 8XPTobias Schramm2020-01-121-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: bcm53128 USB: 1x USB 2.0 Ethernet: 8x GbE, 1x FE The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE and 48V 802.11af/at PoE out on all eight ports. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the eight switch ports. Installation of the firware is possible either via serial + tftpboot or the factory firmware update function via webinterface. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [fix whitespace issue] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Ubiquiti SW devicesTobias Schramm2020-01-121-0/+12
| | | | | | | SW devices are Ubiquit ToughSwitch and EdgeSwitch series devices. Hardware-wise they are very similar to the XM device series. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: gl-ar750s: reduce kernel size to 2M in image MakefileChuanhong Guo2020-01-111-1/+1
| | | | | | | | | | | | | | | | u-boot splits nand factory firmware at 2M offset, flash the first part as kernel into spi nor and the other part as ubi into nand flash. With previous commit increasing kernel size to 4M, generated factory firmware is broken because ubi is at 4M offset. This commit reduces kernel size definition to 2M in image Makefile, producing proper factory image. Partition size in dts is kept unchanged so that sysupgrade to a firmware with 2M+ kernel still works. Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB") Reported-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: remove unused Build/mktplinkfw-combinedAdrian Schmutzler2020-01-081-11/+0
| | | | | | Build/mktplinkfw-combined is not used anywhere, so remove it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move mktplinkfw to tplink-v1-image in image-commands.mkAdrian Schmutzler2020-01-083-36/+13
| | | | | | | | | | | | | | | | | | | | | This move the slightly different target-specific implementations of mktplinkfw from the targets to include/image-commands.mk and renames it to tplink-v1-image. Having a common version will increase consistency between implementation and will complete the tplink build command already present in the new location. Due to the slight differences of the original implementations, this also does some adjustments to the device build commands/variables. This also moves rootfs_align as this is required as dependency. Tested on: - TL-WDR4300 v1 (ath79, factory) - TL-WDR4900 v1 (mpc85xx, sysupgrade) - RE210 v1 (ramips, see Tested-by) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Christoph Krapp <achterin@googlemail.com>
* ath79: use ath10k-ct-smallbuffers for TP-Link RE355/RE450 v1Christoph Krapp2020-01-051-1/+1
| | | | | | | | | Both devices are available in 64M and 128M RAM configurations but there is no visial indication which configuration one might get. So just to be sure we properly support both configurations switch to kmod-atk10k-ct-smallbuffers. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: generate firmware image for aircube-ispChristian Mauderer2019-12-311-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a "factory" image for the aircube-isp devices. Note that the firmware can't be uploaded without prior special preparation. For the most recent instructions on how to do that, visit the OpenWRT wiki page of the Ubiquiti airCube ISP for details: https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp Current procedure: With the original firmware 2.5.0 it is possible to upload and execute a script via the configuration. To do that download and unpack the original configuration, adapt uhttpd config to execute another lua handler (placed in the config directory) and pack and upload it again. The lua handler can call a script that mounts an overlayfs and modifies the "fwupdate.real" binary so that an unsigned image is accepted. The overlayfs is necessary because a security system (called tomoyo) doesn't allow binaries in other locations than /sbin/fwupdate.real (and maybe some more) to access the flash when executed via network. A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for finding out how to patch the binary so that it accepts an unsigned image. The current step-by-step procedure is: - Use a version 2.5.0 of the original firmware. This is important because a binary file will be modified. - Download a configuration. - Unpack it (it's just a tar gz file without an ending). - Add the following to uhttpd: `````` config 'uhttpd' 'other' list listen_http 0.0.0.0:8080 list listen_http [::]:8080 option 'home' '/tmp/persistent/config/patch/www' option lua_prefix '/lua' option lua_handler '/tmp/persistent/config/patch/handler.lua' `````` - Create a `patch` subfolder. - Create a `patch/www` subfolder. - Create a `patch/handler.lua` with the following content: `````` function handle_request(env) uhttpd.send("Status: 200 OK\r\n") uhttpd.send("Content-Type: text/plain\r\n\r\n") local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1" local proc = assert(io.popen(command)) for line in proc:lines() do uhttpd.send(line.."\r\n") end proc:close() end `````` - Create a `patch/patch.sh` with the following content: `````` #!/bin/sh -x set -e set -u set -x UBNTBOX_PATCHED="/tmp/fwupdate.real" MD5FILE="/tmp/patchmd5" cat <<EOF > ${MD5FILE} c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real EOF # check md5 of files that will be patched if ! md5sum -c ${MD5FILE} then echo "******** Error when checking files. Refuse to do anything. ********" exit 0 fi # prepare some overlay functionality LOWERDIR="/tmp/lower_root" mkdir -p ${LOWERDIR} mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR} overlay_some_path() { PATH_TO_OVERLAY=$1 ALIAS=$2 UPPERDIR="/tmp/over_${ALIAS}" WORKDIR="/tmp/over_${ALIAS}_work" mkdir -p ${UPPERDIR} mkdir -p ${WORKDIR} mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY} } # patch the ubntbox binary. overlay_some_path "/sbin" "sbin" echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598 echo "******** Done ********" `````` - Repack the configuration. - Upload it via the normal web interface. - Wait about a minute. The webserver should restart. - Now there is a second web server at port 8080 which can call the lua script. Visit the page with a web browser. Link is for example http://192.168.1.1:8080/lua - You should see the output of the script with a "*** Done ***" at the end. Note that the patches are not permanent. If you restart the router you have to re-visit the link (but not re-upload the config). - Now you can upload an unsigned binary via the normal web interface. Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
* ath79: tp-link: use ath10k-ct-smallbuffers for 64 MiB devicesPaul Fertser2019-12-251-5/+6
| | | | Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: use ath10k-ct-smallbuffers for 64 MiB devicesPaul Fertser2019-12-243-14/+14
| | | | Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: Do not build dlink_dir-615-e4 by defaultHauke Mehrtens2019-12-231-0/+1
| | | | | | | The factory image for the dlink_dir-615-e4 is getting too big which makes the full ath79 tiny build fail, deactivate it by default. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: rename ATH_SOC to SOCAdrian Schmutzler2019-12-208-174/+173
| | | | | | | This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: harmonize line breaks in image MakefilesAdrian Schmutzler2019-12-208-138/+187
| | | | | | | | | | | | | | | | This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add D-Link DIR-615 E4Paul Fertser2019-12-191-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - FCC ID: KA2IR615E3 - SoC: MIPS32 24K 400 MHz Atheros AR7240 - RAM: 32 MiB DDR SDRAM ESMT M13S2561616A-5T - Flash: 4 MiB NOR SPI Macronix MX25L3208E - Wireless: AR9287 2.4 GHz 802.11n 2T2R, 2x RP-SMA connectors - Ethernet: 5x 100BASE-TX Fast Ethernet - LEDs: 9x GPIO, 1x ath9k - Buttons: 2x tactile switches - UART: 3.3 V, 115200 8n1 - USB: simple hardware modification required, 1x USB 1.1 Full Speed Partitioning notes: Vendor firmware (based on CameoAP99) defines two additional partitions: "mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000. The "mac" partition stores LAN MAC address and hardware board name. However, the vendor firmware uses addresses from "nvram" partition, and the board name is used only for informational purposes in the Web interface (included in the pages' header), not affecting the firmware image check. The "lp" partition is supposed to contain a "language pack" (which can be used to add an additional language support to the Web interface) and is flashed separately, using the vendor firmware upgrade page. Since these partitions are absolutely useless for OpenWrt and overwriting them doesn't prevent downgrading to obsolete vendor firmware, this patch appends the valueable space to "firmware". Installation instructions: - Upgrade from OpenWrt ar71xx with "sysupgrade -f -n" or - Upload as a firmware update via the vendor Web-interface or - Connect UART and use "loady" to upload and run OpenWrt initramfs image, then sysupgrade from it (TFTP client doesn't work) or - Before powering up hold "reset" button and keep it pressed for about 15 seconds after, then access fail safe Web server on 192.168.0.1 (the old uIP TCP/IP protocol stack is not compatible with modern Linux, the kernel, so you'll need to use some other OS to do this). Can be performed without a Web-browser too: curl http://192.168.0.1/cgi/index \ -F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* ath79: add support for TP-Link TL-WR902AC v1Lech Perczak2019-12-191-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash OpenWrt (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. MAC Address summary: - wlan1 (2.4GHz Wi-Fi): Label MAC - wlan0 (5GHz Wi-Fi): Offset -1 from label - eth0 (Wired): Offset +1 from label Root access over serial line in vendor firmware: root/sohoadmin. Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [remove size-cells from gpio-export] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WDR4300 v1 (IL)Adrian Schmutzler2019-12-121-0/+11
| | | | | | | | The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID. Thanks to Josh4300 for testing on device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: redistribute UBNT variables in Ubiquiti image MakefileAdrian Schmutzler2019-12-121-15/+18
| | | | | | | | | | | | | The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti LiteBeam AC Gen2Stijn Tintel2019-12-041-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: drop IMAGE/factory.bin from ubnt-wa devicesStijn Tintel2019-12-041-4/+0
| | | | | | | | | | The sysupgrade image contains OpenWrt specific metadata. Having this metadata in the factory images makes no sense. Drop IMAGE/factory.bin from Device/ubnt-wa and use the default from Device/ubnt instead. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)Anderson Vulczak2019-11-271-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for YunCore XD4200 and A782Piotr Dymacz2019-11-251-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based (QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE (802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller version of the XD4200, with similar specification but lower TX power. Specification: - QCA9563 (775 MHz) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN) - Wi-Fi 2.4 GHz: - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11) - Wi-Fi 5 GHz: - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11) - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11) - LEDs: - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet) - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet) - 1x button (reset) - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x DC jack (12 V) Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for YunCore TFTP image generationVincent Wiemann2019-11-252-0/+15
| | | | | | | | | | | | | | | | | | YunCore QCA9k based devices released in 2019 require a custom TFTP image for U-Boot built-in recovery mode (triggered with reset button). Image has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI commands which will be executed later. Images without the custom header will be ignored by U-Boot. To be able to support both the vendor firmware (QSDK) and OpenWrt flash layouts, used here commands change the 'bootcmd' before flashing image. This commit adds generic helper script for YunCore devices with 16 MB of flash and enables TFTP image generation for A770 model. Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com> [pepe2k@gmail.com: commit description reworded, recipe renamed] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: remove ath10k drivers from Archer C7 v1 profileStijn Segers2019-11-241-1/+1
| | | | | | | | | | | Ath10k packages were removed from ar71xx in master in commit 34113999ef43 ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes FS#1743)") but ath79 in master and the 19.07 branch still suffer from the issue. Signed-off-by: Stijn Segers <foss@volatilesystems.org> [commit description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for the TP-LINK WBS510 V1Andrew Cameron2019-11-221-0/+12
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for the TP-LINK WBS510 V2Andrew Cameron2019-11-221-0/+11
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: fix sysupgrade from ar71xx for WNDR3700 V2 and WNDR3800(CH)Adrian Schmutzler2019-11-141-3/+3
| | | | | | | | | | | ar71xx has just one board name "wndr3700" for WNDR3700 V1/V2, WNDR3800 and WNDR3800CH, whereas ath79 provides separate images for the boards. So, update SUPPORTED_DEVICES to store the correct ar71xx board names. Fixes: FS#2510 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Netgear WNDR3700v4Paul Blazejowski2019-11-141-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNDR3700v4. Router was previously supported by ar71xx target only. Note: device requires 'ar934x-nand' driver in kernel. Specification ============= * Description: Netgear WNDR3700v4 * Loader: U-boot * SOC: Atheros AR9344 (560 MHz) * RAM: 128 MiB * Flash: 128 MiB (NAND) - U-boot binary: 256 KiB - U-boot environment: 256 KiB - ART: 256 KiB - POT: 512 KiB - Language: 2 MiB - Config: 512 KiB - Traffic Meter: 3 MiB - Firmware: 25 MiB - ART Backup: 256 KiB - Reserved: 96 MiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (amber/green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 2.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Note about partitioning: firmware partition offset (0x6c0000) is hardcoded into vendor's u-boot, so this partition cannot be moved and resized to include Netgear-specific flash areas (pot, language, config, traffic_meter) not used by OpenWrt. Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr3700-v4=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-16 13:04:36 +0000