| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some boards with firmware made with Senao SDK based on Linux 3.3
have the following lines in the OEM upgrade script at
/etc/fwupgrade.sh
local append=""
local CONF_TAR="/tmp/sysupgrade.tgz"
[ -f "$CONF_TAR" ] && append="-j $CONF_TAR"
and
\# check FWINFO filename
[ -z $(ls FWINFO* | grep -i ${modelname}) ] && errcode="1"
This addition also prevents needing to factory reset after flashing
for some boards that also have these lines in the script
\# Support downgrade but do default (Smart v2.x.x.x -> senaowrt v1.x.x.x)
[ $(ls FWINFO* | grep -i ${modelname} | cut -d "-" -f4 | cut -c 2) -lt 2 ] && append=""
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
| |
|
|
|
|
|
| |
These instructions are repeated for a few devices now, let's move
them to shared definition so we do not repeat ourselves too often.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use a similar upgrade method for sysupgrade.bin, like factory.bin,
for Senao boards with the tar.gz OEM upgrade platform,
and 'failsafe' image which is loaded on checksum failure.
This is inspired by the OEM upgrade script /etc/fwupgrade.sh
and the existing platforms for dual-boot Senao boards.
Previously, if the real kernel was damaged or missing
the only way to recover was with UART serial console,
because the OKLI lzma-loader is programmed to halt.
uboot did not detect cases where kernel or rootfs is damaged
and boots OKLI instead of the failsafe image,
because the checksums stored in uboot environment
did not include the real kernel and rootfs space.
Now, the stored checksums include the space for both
the lzma-loader, kernel, and rootfs.
Therefore, these boards are now practically unbrickable.
Also, the factory.bin and sysupgrade.bin are now the same,
except for image metadata.
This allows for flashing OEM image directly from openwrt
as well as flashing openwrt image directly from OEM.
Make 'loader' partition writable so that it can be updated
during a sysupgrade.
tested with
ENS202EXT v1
EAP1200H
EAP350 v1
EAP600
ECB350 v1
ECB600
ENH202 v1
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
By using the same custom kernel header magic
in both OKLI lzma-loader, DTS, and makefile
this hack is not necessary anymore
However, "rootfs" size and checksum
must now be supplied by the factory.bin image
through a script that is accepted by the OEM upgrade script.
This is because Senao OEM scripts assume a squashfs header exists
at the offset for the original "rootfs" partition
which is actually the kernel + rootfs in this implementation,
and takes size value from the header that would be there with hexdump,
but this offset is now the uImage header instead.
This frees up 1 eraseblock
previously used by the "fakeroot" partition
for bypassing the OEM image verification.
Also, these Senao devices with a 'failsafe' partition
and the tar-gz factory.bin platform would otherwise require
flashing the new tar-gz sysupgrade.bin afterward.
So this also prevents having to flash both images
when starting from OEM or 'failsafe'
the OEM upgrade script verifies the header magic numbers,
but only the first two bytes.
Example:
[ "${magic_word_kernel}" = "2705" ] &&
[ "${magic_word_rootfs}" = "7371" -o "${magic_word_rootfs}" = "6873" ] &&
errcode="0"
therefore picked the magic number
0x73714f4b
which is
'sqOK'
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
|
|
These recipes and definitions can apply
to devices from other vendors
with PCB boards or SDK produced by Senao
not only the brand Engenius
possible examples:
Extreme Networks, WatchGuard, OpenMesh,
Fortinet, ALLNET, OCEDO, Plasma Cloud, devolo, etc.
so rename all of these items
and move DEVICE_VENDOR from common to generic/tiny.mk
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
