aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/generic/base-files/etc
Commit message (Collapse)AuthorAgeFilesLines
* ath79: Move TPLink WPA8630Pv2 to ath79-tiny targetJoe Mullally2022-04-103-12/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | These devices only have 6MiB available for firmware, which is not enough for recent release images, so move these to the tiny target. Note for users sysupgrading from the previous ath79-generic snapshot images: The tiny target kernel has a 4Kb flash erase block size instead of the generic target's 64kb. This means the JFFS2 overlay partition containing settings must be reformatted with the new block size or else there will be data corruption. To do this, backup your settings before upgrading, then during the sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n". If you forget to do this and your system becomes unstable after upgrading, you can do this to format the partition and recover: * Reboot * Press RESET when Power LED blinks during boot to enter Failsafe mode * SSH to 192.168.1.1 * Run "firstboot" and reboot Signed-off-by: Joe Mullally <jwmullally@gmail.com> Tested-by: Robert Högberg <robert.hogberg@gmail.com> (cherry picked from commit 44e1e5d153d00915a7e516c9af3f440cbd84cf78)
* ath79: add support for Araknis AN-700-AP-I-ACMichael Pratt2022-03-132-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: 2AG6R-AN700APIAC Araknis AN-700-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1750 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3 - QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:xb art 0x0 phy1 2.4G *:xc --- phy0 5GHz *:xd --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Araknis AN-500-AP-I-ACMichael Pratt2022-03-132-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: 2AG6R-AN500APIAC Araknis AN-500-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1200 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:e1 art 0x0 phy1 2.4G *:e2 --- phy0 5GHz *:e3 --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Araknis AN-300-AP-I-NMichael Pratt2022-03-132-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: U2M-AN300APIN Araknis AN-300-AP-I-N is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EWS310AP the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2 - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM 1839ZFG V59C1512164QFJ25 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:7d art 0x0 phy1 2.4G *:7e --- phy0 5GHz *:7f --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for TP-Link Archer A9 v6Piotr Dymacz2022-02-272-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer A9 v6 (FCCID: TE7A9V6) is an AC1900 Wave-2 gigabit home router based on a combination of Qualcomm QCN5502 (most likely a 4x4:4 version of the QCA9563 WiSOC), QCA9984 and QCA8337N. The vendor's firmware content reveals that the same device might be available on the US market under name 'Archer C90 v6'. Due to lack of access to such hardware, support introduced in this commit was tested only on the EU version (sold under 'Archer A9 v6' name). Based on the information on the PL version of the vendor website, this device has been already phased out and is no longer available. Specifications: - Qualcomm QCN5502 (775 MHz) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 5x Gbps Ethernet (Qualcomm QCA8337N over SGMII) - Wi-Fi: - 802.11b/g/n on 2.4 GHz: Qualcomm QCN5502* in 4x4:4 mode - 802.11a/n/ac on 5 GHz: Qualcomm QCA9984 in 3x3:3 mode - 3x non-detachable, dual-band external antennas (~3.5 dBi for 5 GHz, ~2.2 dBi for 2.4 GHz, IPEX/U.FL connectors) - 1x internal PCB antenna for 2.4 GHz (~1.8 dBi) - 1x USB 2.0 Type-A - 11x LED (4x connected to QCA8337N, 7x connected to QCN5502) - 2x button (reset, WPS) - UART (4-pin, 2.54 mm pitch) header on PCB (not populated) - 1x mechanical power switch - 1x DC jack (12 V) *) unsupported due to missing support for QCN550x in ath9k UART system serial console notice: The RX signal of the main SOC's UART on this device is shared with the WPS button's GPIO. The first-stage U-Boot by default disables the RX, resulting in a non-functional UART input. If you press and keep 'ENTER' on the serial console during early boot-up, the first-stage U-Boot will enable RX input. Vendor firmware allows password-less access to the system over serial. Flash instruction (vendor GUI): 1. It is recommended to first upgrade vendor firmware to the latest version (1.1.1 Build 20210315 rel.40637 at the time of writing). 2. Use the 'factory' image directly in the vendor's GUI. Flash instruction (TFTP based recovery in second-stage U-Boot): 1. Rename 'factory' image to 'ArcherA9v6_tp_recovery.bin' 2. Setup a TFTP server on your PC with IP 192.168.0.66/24. 3. Press and hold the reset button for ~5 sec while turning on power. 4. The device will download image, flash it and reboot. Flash instruction (web based recovery in first-stage U-Boot): 1. Use 'CTRL+C' during power-up to enable CLI in first-stage U-Boot. 2. Connect a PC with IP set to 192.168.0.1 to one of the LAN ports. 3. Issue 'httpd' command and visit http://192.168.0.1 in browser. 4. Use the 'factory' image. If you would like to restore vendor's firmware, follow one of the recovery methods described above. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for ALFA Network Tube-2HQPiotr Dymacz2022-02-272-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-2HQ is a successor of the Tube-2H/P series (EOL) which was based on the Atheros AR9331. The new version uses Qualcomm QCA9531. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 64 or 128 MB of RAM (DDR2) - 16+ MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) (802.3at/af PoE support with optional module) - 1T1R 2.4 GHz Wi-Fi with external PA (SE2623L, up to 27 dBm) and LNA - 1x Type-N (male) antenna connector - 6x LED (5x driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - UART (4-pin, 2.00 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: utilize nvmem on Netgear EX7300 v2Sungbo Eo2022-02-201-4/+0
| | | | | | | | | | | | | mtd-mac-address should no longer be used after commit 5ae2e786395c ("kernel: drop support for mtd-mac-address"). Convert it to nvmem-cells. While at it, also convert OpenWrt's custom mtd-cal-data property and userspace pre-calibration data extraction to the nvmem implementation. Note: nvmem-cells in QCN5502 wmac has not been tested. Fixes: c32008a37b81 ("ath79: add partial support for Netgear EX7300v2") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: Add support for Ubiquiti NanoBeam AC Gen1 XCDaniel González Cabanelas2022-02-193-0/+4
| | | | | | | | | | | | | | | | | | | | | | The Ubiquiti NanoBeam AC Gen1 XC (NBE-5AC-19) is an outdoor 802.11ac CPE with a waterproof casing (ultrasonically welded) and bulb shaped. Hardware: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR - Ethernet: 1x GbE, AR8033 phy connected via SGMII - PSU: 24 Vdc passive PoE - WiFi 5 GHz: Qualcomm Atheros QCA988X - Buttons: 1x reset - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue - Internal antenna: 19 dBi planar Installation from stock airOS firmware: - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at https://openwrt.org/toh/ubiquiti/common Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* ath79: add partial support for Netgear EX7300v2Wenli Looi2022-02-072-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: QCN5502 Flash: 16 MiB RAM: 128 MiB Ethernet: 1 gigabit port Wireless No1: QCN5502 on-chip 2.4GHz 4x4 Wireless No2: QCA9984 pcie 5GHz 4x4 USB: none Installation ------------ Flash the factory image using the stock web interface or TFTP the factory image to the bootloader. What works ---------- - LEDs - Ethernet port - 5GHz wifi (QCA9984 pcie) What doesn't work ----------------- - 2.4GHz wifi (QCN5502 on-chip) (I was not able to make this work, probably because ath9k requires some changes to support QCN5502.) Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
* ath79: add support for TP-Link TL-WR841HP v2Saiful Islam2022-02-072-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - AR9344 SoC, 8 MB nor flash, 64 MB DDR2 RAM - 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps - 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100 - 1x WAN, 4x LAN, Wifi, PWR, WPS, SYSTEM Leds - Reset/WPS button - Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1 MAC addresses as verified by OEM firmware: vendor OpenWrt address LAN eth0 label WAN eth1 label + 1 WLAN phy0 label The label MAC address was found in u-boot 0x1fc00. Installation: To install openwrt, - set the device's SSID to each of the following lines, making sure to include the backticks. - set the ssid and click save between each line. `echo "httpd -k"> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -r&">> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -k">> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -f">> /tmp/s` `sh /tmp/s` - Now, wait 60 sec. - After the reboot sequence, the router may have fallen back to its default IP address with the default credentials (admin:admin). - Log in to the web interface and go the the firmware upload page. Select "openwrt-ath79-generic-tplink_tl-wr841hp-v2-squashfs-factory.bin" and you're done : the system now accepts the openwrt. Forum support topic: https://forum.openwrt.org/t/support-for-tplink-tl-wr841hp-v2/69445/ Signed-off-by: Saiful Islam <si87868@gmail.com>
* ath79: Add support for OpenMesh OM2P v1Sven Eckelmann2022-01-163-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR7240 rev 2 * 350/350/175 MHz (CPU/DDR/AHB) * 32 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 18-24V passive POE (mode B) + used as WAN interface - eth1 + builtin switch port 4 + used as LAN interface * 12-24V 1A DC * external antenna The device itself requires the mtdparts from the uboot arguments to properly boot the flashed image and to support dual-boot (primary + recovery image). Unfortunately, the name of the mtd device in mtdparts is still using the legacy name "ar7240-nor0" which must be supplied using the Linux-specfic DT parameter linux,mtd-name to overwrite the generic name "spi0.0". Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM5P-AC v2Sven Eckelmann2022-01-161-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: patch Asus RP-AC66 clean up and fix for sysupgrade imageTamas Balogh2022-01-152-8/+4
| | | | | | | | - clean up leftovers regarding MAC configure in dts - fix alphabetical order in caldata - IMAGE_SIZE for sysupgrade image Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ath79: Add support for OpenMesh OM5P-AC v1Sven Eckelmann2022-01-092-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM5P-ANSven Eckelmann2022-01-092-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 1T1R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + 10/100 Mbps Ethernet + builtin switch port 1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: add support for ASUS RP-AC66Tamas Balogh2022-01-094-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC66 Repeater Hardware specifications: Board: AP152 SoC: QCA9563 DRAM: 64MB DDR2 Flash: 25l128 16MB SPI-NOR LAN/WAN: 1x1000M QCA8033 WiFi 5GHz: QCA9880 Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz MAC addresses as verified by OEM firmware: use address source Lan/Wan *:24 art 0x1002 (label) 2G *:24 art 0x1002 5G *:26 art 0x5006 Installation: Asus windows recovery tool: - install the Asus firmware restoration utility - unplug the router, hold the reset button while powering it on - release when the power LED flashes slowly - specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 - Start the Asus firmware restoration utility, specify the factory image and press upload - Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: - set computer to a static ip, 192.168.1.75 - connect computer to the LAN 1 port of the router - hold the reset button while powering on the router for a few seconds - send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ath79: add support for WD My Net N600Ryan Mounce2021-12-112-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: AR9344 RAM: 128MB Flash: 16MiB SPI NOR 5GHz WiFi: AR9382 PCIe 2x2:2 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Fast ethernet via SoC switch (green LEDs) 1x USB 2.0 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX Flash factory image via "emergency room" recovery: - Configure your computer with a static IP 192.168.1.123/24 - Connect to LAN port on the N600 switch - Hold reset putton - Power on, holding reset until the power LED blinks slowly - Visit http://192.168.1.1/ and upload OpenWrt factory image - Wait at least 5 minutes for flashing, reboot and key generation - Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image Signed-off-by: Ryan Mounce <ryan@mounce.com.au> [dt leds preparations] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for jjPlus JWAP230Olivier Valentin2021-12-111-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The jjPlus JWAP230 is an access point board built around the QCA9558, with built-in 2.4GHz 3x3 N WiFi (28dBm). It can be expanded with 2 mini-PCIe boards, and has an USB2 root port. Specifications: - SOC: Qualcomm Atheros QCA9558 - CPU: 720MHz - H/W switch: QCA8327 rev 2 - Flash: 16 MiB SPI NOR (en25qh128) - RAM: 128 MiB DDR2 - WLAN: AR9550 built-in SoC bgn 3T3R (ath9k) - PCI: 2x mini-PCIe (optional 5V) - LEDs: 6x LEDs (3 are currently available) - Button: 1x Reset (not yet defined) - USB2: - 1x Type A root port - 1x combined mini-PCIe - Ethernet: - 2x 10/100/1000 (1x PoE 802.3af (36-57 V)) Notes: The device used to be supported in the ar71xx target. For upgrades: Please use "sysupgrade --force -n <image>". This will restore the device back to OpenWrt defaults! MAC address assignment: use source LAN art 0x0 WAN art 0x6 WLAN art 0x1002 (as part of the calibration data) Flash instructions: - install from u-boot with tftp (requires serial access) > setenv ipaddr a.b.c.d > setenv serverip e.f.g.h > tftp 0x80060000 \ openwrt-ath79-generic-jjplus_jwap230-squashfs-sysupgrade.bin > erase 0x9f050000 +${filesize} > cp.b $fileaddr 0x9f050000 $filesize > setenv bootcmd bootm 0x9f050000 > saveenv Signed-off-by: Olivier Valentin <valentio@free.fr> [Added DT-Leds (based on ar71xx), Added more notes about sysupgrade, fixed "qca9550" to match SoC in commit and dts file name] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for TP-Link EAP225 v1Sander Vanheule2021-12-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link EAP225 v1 is an AC1200 (802.11ac Wave-1) ceiling mount access point. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 2x2 * Wireless 5Ghz (QCA9882): a/n/ac, 2x2 * Ethernet (AR8033): 1× 1GbE, 802.3at PoE Flashing instructions: * Ensure the device is upgraded to firmware v1.4.0 * Exploit the user management page in the web interface to start telnetd by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`. * Immediately change the malformed username back to something valid (e.g. 'admin') to make ssh work again. * Use the root shell via telnet to make /tmp world writeable (chmod 777) * Extract /usr/bin/uclited from the device via ssh and apply the binary patch listed below. The patch is required to prevent `uclited -u` in the last step from crashing. * Copy the patched uclited binary back to the device at /tmp/uclited (via ssh) * Upload the factory image to /tmp/upgrade.bin (via ssh) * Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt. uclited patching: --- xxd uclited +++ xxd uclited-patched @@ -53811,7 +53811,7 @@ 000d2330: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... .......... 000d2340: 8fa6 0a4c 02c0 2821 8f82 87c4 0000 0000 ...L..(!........ -000d2350: 8c44 0000 0c13 461c 27a7 0018 8fbc 0010 .D....F.'....... +000d2350: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$........... 000d2360: 1040 001d 0000 1821 8f99 8378 3c04 0058 .@.....!...x<..X 000d2370: 3c05 0056 2484 ad68 24a5 9f00 0320 f809 <..V$..h$.... .. To make sure the correct file is patched, the following MD5 checksums should match the unpatched and patched files: 4bd74183c23859c897ed77e8566b84de uclited 4107104024a2e0aeaf6395ed30adccae uclited-patched Debricking: * Serial port can be soldered on unpopulated 4-pin header (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors running from pins 1 (TXD) and 2 (RXD). Do NOT bridge the pull-down for pin 2, running parallel to the header. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via the LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr Tested by forum user KernelMaker. Link: https://forum.openwrt.org/t/eap225-v1-firmware/87116 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: add Embedded Wireless Balin PlatformCatrinel Catrinescu2021-12-031-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | Add the Embedded Wireless "Balin" platform, it is in ar71xx too SoC: QCA AR9344 or AR9350 RAM: DDR2-RAM 64MBytes Flash: SPI-NOR 16MBytes WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n Ethernet: 3 x 10/100 Mb/s USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up PCIe: MiniPCIe - 1 x lane PCIe 1.2 Button: 1 x Reset-Button UART: 1 x Normal, 1 x High-Speed JTAG: 1 x EJTAG LED: 1 x Green Power/Status LED GPIO: 10 x Input/Output multiplexed The module comes already with the current vanilla OpenWrt firmware. To update, use "sysupgrade -n --force <image>" image directly in vendor firmware. This resets the existing configurations back to default! Signed-off-by: Catrinel Catrinescu <cc@80211.de> [indent, led function+color properties, fix partition unit-address, re-enable pcie port, mention button+led in commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert TP-Link Archer C7v1/2 Wifis to nvmem-cellsChristian Lamparter2021-11-281-1/+0
| | | | | | | | | | | | | | | For v2, both ath9k (2.4GHz Wifi) and ath10k (5 GHz) driver now pull the (pre-)calibration data from the nvmem subsystem. v1 is slightly different as only the ath9k Wifi is supported. This allows us to move the userspace caldata extraction and mac-address patching for the 5GHZ ath10k supported wifi into the device-tree definition of the device. ath9k's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: move cal-data extraction to dts for DAP-2695Sebastian Schaper2021-11-202-4/+1
| | | | | | | | | | This device can be merged with the existing dtsi, which declares the location of ath9k cal-data via devicetree, correcting the 2.4G mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`. To make these changes more visible, apply before merging with dtsi. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: WNDR3700/3800/MAC: utilize nvmem for caldata fetchingChristian Lamparter2021-11-061-14/+2
| | | | | | | | converts the still popular WNDR3700 Series to fetch the caldata through nvmem. As the "MAC with NVMEM" has shown, there could pitfalls along the way. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: fix UBNT Aircube AC gpiosNicolò Veronese2021-11-011-3/+3
| | | | | | | | | | GPIOs on the Aircube AC are wrong: - Reset GPIO moved from 17 to 12 - PoE Pass Through GPIO for Aircube AC is 3 Fixes: 491ae3357e10 ("ath79: add support for Ubiquiti airCube AC") Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* ath79: add support for Letv LBA-047-CHShiji Yang2021-11-011-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: QCA9531 650 MHz ROM: 16 MiB Flash (Winbond W25Q128FV) RAM: 128 MiB DDR2 (Winbond W971GG6SB) LAN: 10/100M *2 WAN: 10/100M *1 LED: BGR color *1 Mac address: label C8:0E:77:xx:xx:68 art@0x0 lan C8:0E:77:xx:xx:62 art@0x6 wan C8:0E:77:xx:xx:68 art@0x0 (same as the label) wlan C8:0E:77:xx:xx:B2 art@0x1002 (load automatically) TFTP installation: * Set local IP to 192.168.67.100 and open tftpd64, link lan port to computer. Rename "xxxx-factory.bin" to "openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin". * Make sure firmware file is in the tftpd's directory, push reset button and plug in, hold it for 5 seconds, and then it will download firmware from tftp server automatically. More information: * This device boot from flash@0xe80000 so we need a okli loader to deal with small kernel partition issue. In order to make full use of the storage space, connect a part of the previous kernel partition to the firmware. Stock Modify 0x000000-0x040000(u-boot) 0x000000-0x040000(u-boot) 0x040000-0x050000(u-boot-env) 0x000000-0x050000(u-boot-env) 0x050000-0xe80000(rootfs) 0x050000-0xe80000(firmware part1) 0xe80000-0xff0000(kernel) 0xe80000-0xe90000(okli-loader) 0xe90000-0xff0000(firmware part2) 0xff0000-0x1000000(art) 0xff0000-0x1000000(art) Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: add support for TP-Link CPE710-v1Andrew Cameron2021-09-253-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [convert to nvmem, fix MAC assignment in 11-ath10k-caldata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WA1201 v2Robert Balas2021-09-053-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is a wireless access point working on the 2.4 GHz and 5 GHz band, based on Qualcomm/Atheros QCA9563 + QCA9886. Specification - 775 MHz CPU - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - QCA9563: 2.4 GHz 3x3 - QCA9886: 5 GHz - AR8033: 1x 1 Gbs Ethernet - 4x LED, WPS factory reset and power button - bare UART on PCB (accessible through testpoints) Methods for Flashing: - Apply factory image in OEM firmware web-gui. Wait a minute after the progress bar completes and restart the device. - Sysupgrade on top of existing OpenWRT image - Solder wires onto UART testpoints and attach a terminal. Boot the device and press enter to enter u-boot's menu. Then issue the following commands 1. setenv serverip your-server-ip setenv ipaddr your-device-ip 2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in hex, henceforth "sizeinhex") 3. erase 0x9f030000 +"sizeinhex" 4. cp.b 0x80060000 0x9f030000 0x"sizeinhex" 5. reboot Recover: - U-boot serial console Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch> [convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for onion omegaJan-Niklas Burfeind2021-08-261-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Onion Omega is a hardware development platform with built-in WiFi. https://onioniot.github.io/wiki/ Specifications: - QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor) - 64MB of DDR2 RAM running at 400 MHz - 16MB of on-board flash storage - Support for USB 2.0 - Support for Ethernet at 100 Mbps - 802.11b/g/n WiFi at 150 Mbps - 18 digital GPIOs - A single Serial UART - Support for SPI - Support for I2S Flash instructions: The device is running OpenWrt upon release using the ar71xx target. Both a sysupgrade and uploading the factory image using u-boots web-UI do work fine. Depending on the ssh client, it might be necessary to enable outdated KeyExchange methods e.g. in the clients ssh-config: Host 192.168.1.1 KexAlgorithms +diffie-hellman-group1-sha1 The stock credentials are: root onioneer For u-boots web-UI manually configure `192.168.1.2/24` on your computer, connect to `192.168.1.1`. MAC addresses as verified by OEM firmware: 2G phy0 label LAN eth0 label - 1 LAN is only available in combination with an optional expansion dock. Based on vendor acked commit: commit 5cd49bb067ca ("ar71xx: add support for Onion Omega") Partly reverts: commit fc553c7e4c8e ("ath79: drop unused/incomplete dts") Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* ath79: add support for Compex WPJ558 (16M)Romain Mahoux2021-08-251-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: QCA9558 - DRAM: 128MB DDR2 - Flash: 16MB SPI-NOR - Wireless: on-board abgn 2×2 2.4GHz radio - Ethernet: 2x 10/100/1000 Mbps (1x 802.11af PoE) - miniPCIe slot Flash instruction: - From u-boot tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj558-16m-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize boot - From cpximg loader The cpximg loader can be started either by holding the reset button during power up. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '6A07': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj558-16m-squashfs-cpximg-6a07.bin Signed-off-by: Romain Mahoux <romain@mahoux.fr> [convert to nvmem, remove redundant lan_mac in 02_network] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Atheros DB120 reference boardZoltan HERPAI2021-08-222-14/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Atheros DB120 reference board. Specifications: SoC: QCA9344 DRAM: 128Mb DDR2 Flash: 8Mb SPI-NOR, 128Mb NAND flash Switch: 5x 10/100Mbps via AR8229 switch (integrated into SoC), 5x 10/100/1000Mbps via QCA8237 via RGMII WLAN: AR9300 (SoC, 2.4G+5G) + AR9340 (PCIe, 5G-only) USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x reset LEDs: a lot Slots: 2x mPCIe + 1x mini-PCI, but using them requires additional undocumented changes. Misc: The board allows to boot off NAND, and there is I2S audio support as well - also requiring additional undocumented changes. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-atheros_db120-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-atheros_db120-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> [explicit factory recipe in generic.mk, sorting in 10-ath9k-eeprom, convert to nvmem, use fwconcat* names in DTS, remove unneeded DT labels, remove redundant uart node] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBeam M2 (XW)Russell Senior2021-08-222-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Ubiquiti PowerBeam M2 (XW), e.g. PBE-M2-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-ubnt_powerbeam-m2-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM2HP Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: rename Ubiquiti PowerBeam M (XW) to PowerBeam M5 (XW)Russell Senior2021-08-222-2/+2
| | | | | | | | | | | | | | The commit [1] added support for Ubiquiti PowerBeam M (XW), tested on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different ethernet configuration, so make the support specific to the m5 version in anticipation of adding specific support for the m2 in a separate commit. [1] 12eb5b2384a6 ("ath79: add support for Ubiquiti PowerBeam M (XW)") Signed-off-by: Russell Senior <russell@personaltelco.net> [fix model name in DTS, format commit reference in commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for GL.iNet GL-X300BJohn Marrett2021-08-052-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL-X300B is a industrial 4G LTE router based on the Qualcomm QCA9531 SoC. Specifications: - Qualcomm QCA9531 @ 650 MHz - 128 MB of RAM - 16 MB of SPI NOR FLASH - 2x 10/100 Mbps Ethernet - 2.4GHz 802.11b/g/n - 1x USB 2.0 (vbus driven by GPIO) - 4x LED, driven by GPIO - 1x button (reset) - 1x mini pci-e slot (vcc driven by GPIO) - RS-485 Serial Port (untested) Flash instructions: This firmware can be flashed using either sysupgrade from the GL.iNet firmware or the recovery console as follows: - Press and hold the reset button - Connect power to the router, wait five seconds - Manually configure 192.168.1.2/24 on your computer, connect to 192.168.1.1 - Upload the firmware image using the web interface RS-485 serial port is untested and may depend on the following commit in the GL.iNet repo: https://github.com/gl-inet/openwrt/commit/202e83a32ae308fbb70502b6dbe3bb0bf8b1fba9 MAC addresses as verified by OEM firmware: vendor OpenWrt address WAN eth0 label LAN eth1 label + 1 2g phy0 label + 2 The label MAC address was found in the art partition at 0x0 Based on vendor commit: https://github.com/gl-inet/openwrt/commit/16c5708b207eb76ff19a040dc973e560d3d8074b Signed-off-by: John Marrett <johnf@zioncluster.ca>
* ath79: add support for Joy-IT JT-OR750iVincent Wiemann2021-07-283-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * QCA9531, 16 MiB flash (Winbond W25Q128JVSQ), 128 MiB RAM * 802.11n 2T2R (external antennas) * QCA9887, 802.11ac 1T1R (connected with diplexer to one of the antennas) * 3x 10/100 LAN, 1x 10/100 WAN * UART header with pinout printed on PCB Installation: * The device comes with a bootloader installed only * The bootloader offers DHCP and is reachable at http://10.123.123.1 * Accept the agreement and flash sysupgrade.bin * Use Firefox if flashing does not work TFTP recovery with static IP: * Rename sysupgrade.bin to jt-or750i_firmware.bin * Offer it via TFTP server at 192.168.0.66 * Keep the reset button pressed for 4 seconds after connecting power TFTP recovery with dynamic IP: * Rename sysupgrade.bin to jt-or750i_firmware.bin * Offer it via TFTP server with a DHCP server running at the same address * Keep the reset button pressed for 6 seconds after connecting power Co-authored-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
* ath79: add support for TP-Link RE455 v1Roberto Valentini2021-07-113-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE455 v1 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. This device is nearly identical to RE450 v3 Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB[1] Flash instruction: Apply factory image in OEM firmware web-gui. [1] Didn't work, probably need to short unpopulated resistor R64 and R69 as RE450v3 Signed-off-by: Roberto Valentini <valantin89@gmail.com>
* ath79: base-files: fix broken network configPetr Štetiar2021-07-051-1/+1
| | | | | | | | | | | | | | Fix bash syntax error introduced in commit cce2e8db564b ("ath79: add support for TP-Link TL-WR941HP v1") which resulted in broken default network configuration. In target/linux/ath79/generic/base-files/etc/board.d/02_network line 402: tplink,tl-wr842n-v2)\ ^-- SC1073: Couldn't parse this case item. Fix to allow more checks. References: https://gitlab.com/ynezz/openwrt-device-runtime-testing/-/jobs/1398837698/artifacts/file/cram-result-archer-c7-v5-initramfs.txt Fixes: cce2e8db564b ("ath79: add support for TP-Link TL-WR941HP v1") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Xiaomi AIoT Router AC2350Evgeniy Isaev2021-07-053-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications * SoC: QCA9563 @ 775MHz (MIPS 74Kc) * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR (EN25QH128) * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9988): a/n/ac, 4x4 MU-MIMO * IoT Wireless 2.4GHz (QCA6006): currently unusable * Ethernet (AR8327): 3 LAN × 1GbE, 1 WAN × 1GbE * LEDs: Internet (blue/orange), System (blue/orange) * Buttons: Reset * UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1) * Power: 12VDC, 1,5A MAC addresses map (like in OEM firmware) art@0x0 88:C3:97:*:57 wan/label art@0x1002 88:C3:97:*:2D lan/wlan2g art@0x5006 88:C3:97:*:2C wlan5g Obtain SSH Access 1. Download and flash the firmware version 1.3.8 (China). 2. Login to the router web interface and get the value of `stok=` from the URL 3. Open a new tab and go to the following URL (replace <STOK> with the stok value gained above; line breaks are only for easier handling, please put together all four lines into a single URL without any spaces): http://192.168.31.1/cgi-bin/luci/;stok=<STOK>/api/misystem/set_config_iotdev ?bssid=any&user_id=any&ssid=-h%0Anvram%20set%20ssh_en%3D1%0Anvram%20commit %0Ased%20-i%20%27s%2Fchannel%3D.%2A%2Fchannel%3D%5C%5C%22debug%5C%5C%22%2F g%27%20%2Fetc%2Finit.d%2Fdropbear%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A 4. Wait 30-60 seconds (this is the time required to generate keys for the SSH server on the router). Create Full Backup 1. Obtain SSH Access. 2. Create backup of all flash (on router): dd if=/dev/mtd0 of=/tmp/ALL.backup 3. Copy backup to PC (on PC): scp root@192.168.31.1:/tmp/ALL.backup ./ Tip: backup of the original firmware, taken three times, increases the chances of recovery :) Calculate The Password * Locally using shell (replace "12345/E0QM98765" with your router's serial number): On Linux printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \ md5sum - | head -c8 && echo On macOS printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \ md5 | head -c8 * Locally using python script (replace "12345/E0QM98765" with your router's serial number): wget https://raw.githubusercontent.com/eisaev/ax3600-files/master/scripts/calc_passwd.py python3.7 -c 'from calc_passwd import calc_passwd; print(calc_passwd("12345/E0QM98765"))' * Online https://www.oxygen7.cn/miwifi/ Debricking (lite) If you have a healthy bootloader, you can use recovery via TFTP using programs like TinyPXE on Windows or dnsmasq on Linux. To switch the router to TFTP recovery mode, hold down the reset button, connect the power supply, and release the button after about 10 seconds. The router must be connected directly to the PC via the LAN port. Debricking You will need a full dump of your flash, a CH341 programmer, and a clip for in-circuit programming. Install OpenWRT 1. Obtain SSH Access. 2. Create script (on router): echo '#!/bin/sh' > /tmp/flash_fw.sh echo >> /tmp/flash_fw.sh echo '. /bin/boardupgrade.sh' >> /tmp/flash_fw.sh echo >> /tmp/flash_fw.sh echo 'board_prepare_upgrade' >> /tmp/flash_fw.sh echo 'mtd erase rootfs_data' >> /tmp/flash_fw.sh echo 'mtd write /tmp/openwrt.bin firmware' >> /tmp/flash_fw.sh echo 'sleep 3' >> /tmp/flash_fw.sh echo 'reboot' >> /tmp/flash_fw.sh echo >> /tmp/flash_fw.sh chmod +x /tmp/flash_fw.sh 3. Copy `openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin` to the router (on PC): scp openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin \ root@192.168.31.1:/tmp/openwrt.bin 4. Flash OpenWRT (on router): /bin/ash /tmp/flash_fw.sh & 5. SSH connection will be interrupted - this is normal. 6. Wait for the indicator to turn blue. Signed-off-by: Evgeniy Isaev <isaev.evgeniy@gmail.com> [improve commit message formatting slightly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR941HP v1Diogenes Rengo2021-07-042-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm Atheros TP9343 (750 MHz) Flash: 8 Mb (GigaDevice GD25Q64CSIG) RAM: 64 Mb (Zentel A3R12E40DBF-8E) Serial: yes, 4-pin header Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA 3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L Ethernet: Qualcomm Atheros TP9343 Lan speed: 100M ports: 4 Lan speed: 100M ports: 1 Other info: same case, ram and flash that TP-Link TL-WR841HP, different SOC https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/ Label MAC addresses based on vendor firmware: LAN *:ee label WAN *:ef label +1 WLAN *:ee label The label MAC address found in "config" partition at 0x8 Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com> [remove various whitespace issues, squash commits, use short 0x0] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBeam M (XW)Russell Senior2021-07-042-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM5HP Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: add support for Teltonika RUT230 v1David Bauer2021-06-301-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Teltonika RUT230 v1, a Atheros AR9331 based router with a Quectel UC20 UMTS modem. Hardware -------- Atheros AR9331 16 MB SPI-NOR XTX XT25F128B 64M DDR2 memory Atheros AR9331 1T1R 802.11bgn Wireless Boootloader: pepe2k U-Boot mod Hardware-Revision ----------------- There are two board revisions of the RUT230, a v0 and v1. A HW version is silkscreened on the top of the PCBs front side as well as shown in the Teltonika UI. However, this looks to be a different identifier, as the GPl dump shows this silkscreened / UI shown version are internally treated identically. Th following mapping has been obtained from the latest GPl dump. HW Ver 01 - 04 --> v0 HW Ver > 05 --> v1 My board was a HW Ver 09 and is treated as a v1. Installation ------------ While attaching power, hold down the reset button and release it after the signal LEDs flashed 3 times. Attach your Computer with the devices LAN port and assign yourself the IPv4 address 192.168.1.10/24. Open a web browser, navigate to 192.168.1.1. Upload the OpenWrt factory image. The device will install OpenWrt and automatically reboots afterwards. You can use the smae procedure with the stock firmware to return back to the vendor firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WR841HP v3Andy Lee2021-06-132-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - QCA9533 SoC, 8 MB nor flash, 64 MB DDR2 RAM - 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps - 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100 - 1x WAN, LAN, Wifi, PWR, WPS, RE Leds - Reset, Wifi on/off, WPS, RE buttons - Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1 Label MAC addresses based on vendor firmware: LAN *:ea label WAN *:eb label +1 2.4 GHz *:ea label The label MAC address in found in u-boot 0x1fc00 Installation: Upload openwrt-ath79-generic-tplink_tl-wr841hp-v3-squashfs-factory.bin from stock firmware webgui. Maybe we need rename to shorten file name due to stock webgui error. Revert back to stock firmware instructions: - set your PC to static IP address 192.168.0.66 netmask 255.255.255.0 - download stock firmware from Tp-link website - put it in the root directory of tftp server software - rename it to wr841hpv3_tp_recovery.bin - power on while pressing Reset button until any Led is lighting up - wait for the router to reboot. done Forum support topic: https://forum.openwrt.org/t/support-for-tp-link-tl-wr841hp-v3-router Signed-off-by: Andy Lee <congquynh284@yahoo.com> [rebase and squash] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Support for Ubiquiti Rocket 5AC LiteNick Hainke2021-06-072-0/+2
| | | | | | | | | | | | | | | | | | | The Ubiquiti Rocket 5AC Lite (R5AC-Lite) is an outdoor router. Specifications: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB - Flash: 16 MB SPI - Ethernet: 1x 10/100/1000 Mbps - WiFi 5 GHz: QCA988x - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI Installation: - Instructions for XC-type Ubiquiti: https://openwrt.org/toh/ubiquiti/common Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: add support for NEC Aterm WF1200CRINAGAKI Hiroshi2021-06-063-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on QCA9561. Specification: - SoC : Qualcomm Atheros QCA9561 - RAM : DDR2 128 MiB (W971GG6SB-25) - Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9561 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100 Mbps - Switch : QCA9561 (SoC) - LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from "JP1" marking - 115200n8 - Power : 12 VDC, 0.9 A Flash instruction using factory image (stock: < v1.3.2): 1. Boot WF1200CR normally with "Router" mode 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Alternate flash instruction using initramfs image (stock: >= v1.3.2): 1. Prepare the TFTP server with the IP address 192.168.1.10 and place the OpenWrt initramfs image to the TFTP directory with the name "0101A8C0.img" 2. Connect serial console to WF1200CR 3. Boot WF1200CR and interrupt with any key after the message "Hit any key to stop autoboot: 2", the U-Boot starts telnetd after the message "starting telnetd server from server 192.168.1.1" 4. login the telnet (address: 192.168.1.1) 5. Perform the following commands to modify "bootcmd" variable temporary and check the value (to ignore the limitation of available commands, "tp; " command at the first is required as dummy, and the output of "printenv" is printed on the serial console) tp; set bootcmd 'set autostart yes; tftpboot' tp; printenv 6. Save the modified variable with the following command and reset device tp; saveenv tp; reset 7. The U-Boot downloads initramfs image from TFTP server and boots it 8. On initramfs image, download the sysupgrade image to the device and perform the following commands to erase stock firmware and sysupgrade mtd erase firmware sysupgrade <sysupgrade image> 9. After the rebooting by completion of sysupgrade, start U-Boot telnetd and login with the same way above (3, 4) 10. Perform the following commands to reset "bootcmd" variable to the default and reset the device tp; run seattle tp; reset (the contents of "seattle": setenv bootcmd 'bootm 0x9f070040' && saveenv) 11. Wait booting-up the device Known issues: - the following 6x LEDs are connected to the gpio controller on QCA9888 chip and the implementation of control via the controller is missing in ath10k/ath10k-ct - "ACTIVE" (Red/Green) - "2.4GHz" (Red/Green) - "5GHz" (Red/Green) Note: - after the version v1.3.2 of stock firmware, "offline update" by uploading image by user is deleted and the factory image cannot be used - the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN and the configuration is required on OpenWrt - gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output - pinmux: set GPIO 14/19 as switch-controlled LEDs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Devolo dLAN pro 1200+ WiFi acFelix Matouschek2021-06-064-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Devolo dLAN pro 1200+ WiFi ac. This device is a plc wifi AC2400 router/extender with 2 Ethernet ports, has a QCA7500 PLC and uses the HomePlug AV2 standard. Other than the PLC the hardware is identical to the Devolo Magic 2 WIFI. Therefore it uses the same dts, which was moved to a dtsi to be included by both boards. This is a board that was previously included in the ar71xx tree. Hardware: SoC: AR9344 CPU: 560 MHz Flash: 16 MiB (W25Q128JVSIQ) RAM: 128 MiB DDR2 Ethernet: 2xLAN 10/100/1000 PLC: QCA75000 (Qualcomm HPAV2) PLC Uplink: 1Gbps MIMO PLC Link: RGMII 1Gbps (WAN) WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9882-BR4A 5GHz 802.11ac Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2 Button: 3x Buttons (Reset, wifi and plc) LED: 3x Leds (wifi, plc white, plc red) GPIO Switch: 11-PLC Pairing (Active Low) 13-PLC Enable 21-WLAN power MACs Details verified with the stock firmware: Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002 Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006 Ethernet &ethernet *:4e = 2.4 GHz + 2 PLC uplink --- *:4f = 2.4 GHz + 3 Label MAC address is from PLC uplink The Powerline (PLC) interface of the dLAN pro 1200+ WiFi ac requires 3rd party firmware which is not available from standard OpenWrt package feeds. There is a package feed on github which you must add to OpenWrt buildroot so you can build a firmware image which supports the plc interface. See: https://github.com/0xFelix/dlan-openwrt (forked from Devolo and added compatibility for OpenWrt 21.02) Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.100 2. Download the sysupgrade image and rename it to uploadfile 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Allow 1-2 minutes for the first boot. Signed-off-by: Felix Matouschek <felix@matouschek.org> [add "plus" to compatible and device name] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove "+" sign for increment with macaddr_addAdrian Schmutzler2021-06-052-16/+16
| | | | | | | | | | | | Many people appear to use an unneeded "+" prefix for the increment when calculating a MAC address with macaddr_add. Since this is not required and used inconsistently [*], just remove it. [*] As a funny side-fact, copy-pasting has led to almost all hotplug.d files using the "+", while nearly all of the 02_network files are not using it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Qualcomm AP143 reference boardsZoltan HERPAI2021-06-052-1/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9533 DRAM: 32Mb DDR1 Flash: 8/16Mb SPI-NOR LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC) on GMII WAN: 1x 10/100Mbps via MII WLAN: QCA9530 USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x WPS, 1x reset LEDs: 8x LEDs A version with 4Mb flash is also available, but due to lack of enough space it's not supported. As the original flash layout does not provide enough space for the kernel (1472k), the firmware uses OKLI and concat flash to overcome the limitation without changing the boot address of the bootloaders. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize Reboot the board. 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. For the 16M version of the board, please use openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> [use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE, set up IMAGE/factory.bin without metadata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for OpenMesh A40Sven Eckelmann2021-06-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh A60Sven Eckelmann2021-06-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8031 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: fix leading whitespaces in generic 01_ledsAdrian Schmutzler2021-05-171-2/+2
| | | | | | Use tabs consistently. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for COMFAST CF-E375ACJoao Henrique Albuquerque2021-05-173-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337. Short specification: 2x 10/100/1000 Mbps Ethernet, with PoE support 128MB of RAM (DDR2) 16 MB of FLASH 3T3R 2.4 GHz, 802.11b/g/n 2T2R 5 GHz, 802.11ac/n/a, wave 2 built-in 5x 3 dBi antennas output power (max): 500 mW (27 dBm) 1x RGB LED, 1x button built-in watchdog chipset Flash instruction: 1) Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. 2) TFTP 2.1) Set a tftp server on your machine with a fixed IP address of 192.168.1.10. A place the sysupgrade as firmware_auto.bin. 2.2) boot the device with an ethernet connection on fixed ip route 2.3) wait a few seconds and try to login via ssh 3) TFTP trough Bootloader 3.1) open the device case and get a uart connection working 3.2) stop the autoboot process and test connection with serverip 3.3) name the sysupgrade image firmware.bin and run firmware_upg MAC addresses: Though the OEM firmware has four adresses in the usual locations, it appears that the assigned addresses are just incremented in a different way: interface address location LAN: *:DC 0x0 WAN *:DD 0x1002 WLAN 2.4g *:E6 n/a (0x0 + 10) WLAN 5g *:DE 0x6 unused *:DF 0x5006 The MAC address pointed at the label is the one assign to the LAN interface. Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com> [add label-mac-device, remove redundant uart status, fix whitespace issues, fix commit message wrapping, remove x bit on DTS file] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-11 17:03:44 +0000