aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/dts
Commit message (Collapse)AuthorAgeFilesLines
* ath79: ubnt-bullet-m-xw: Remove eth1 disabled nodePetr Štetiar2018-12-271-4/+0
| | | | | | It's redundant as eth1 is disabled by default in ath79.dtsi. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Move eth0 mtd-mac-address to the common includePetr Štetiar2018-12-272-2/+4
| | | | | | | It's same for Bullet and Nanostation so far, so let's hope it's going to be the same for other boards sharing the same platform. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Remove pll-data property from eth0 nodePetr Štetiar2018-12-271-1/+0
| | | | | | | | | | | | | | | | | | It's not necessary as it's already defined in ar934x.dtsi to: pll-data = <0x16000000 0x00000101 0x00001616>; And in ar71xx it's currently set to the same values: #define AR934X_PLL_VAL_1000 0x16000000 #define AR934X_PLL_VAL_100 0x00000101 #define AR934X_PLL_VAL_10 0x00001616 And dumping the value from the airOS v6.1.7 has the same value: AR934X_PLL_ETH_XMII_CONTROL_REG 0x1805002C 0x101 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-xw: Add LED aliases for diag and status LED supportPetr Štetiar2018-12-271-1/+8
| | | | | | | | Currently there is no LED signalization for various system states implemented in diag.sh, so this patch adds support for it. Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for devolo WiFi pro 1750cDavid Bauer2018-12-271-0/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button There is also a Micro-B USB-port present but this only seems to be a dummy as the circuit next to it is not present (at least in my unit). It is also not mentioned in the devolo manual. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1200eDavid Bauer2018-12-272-0/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer C7 v5TOCK Chiu2018-12-271-0/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for TP-Link Archer C7 v5, leveraging most effort from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5 but with a different flash layout. Specification: - QCA9563 SoC (750 MHz) - 128 MiB of RAM (DDR2) - 16 MiB of flash (SPI) - 5x 1 Gbps Ethernet (1x WAN + 4x LAN) - 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880 - 10x LED, 2x button - UART header on PCB Flash instructions: 1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin via web interface. Flash instructions using TFTP recovery: 1. Plug PC to one of the LAN ports 2. Set PC to fixed IP address 192.168.0.66 3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in TFTP root directory 4. Turn on the router with the reset button pressed for about 15 secs 5. Release the button and wait about 150 secs to complete flashing Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
* ath79: fix pinmux reg size for QCA955xChristian Lamparter2018-12-241-1/+1
| | | | | | | | The range of pinmux reg property "<0x1804002c 0x40>" for QCA955x SoC does not includes GPIO_FUNCTION register. Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for NEC Aterm WG800HPINAGAKI Hiroshi2018-12-241-0/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 1T1R (QCA9887) - 4x 10/100/1000 Mbps Ethernet - 8x LEDs, 3x keys (2x buttons, 1x slide-switch) - UART through-hole on PCB (J2) - Vcc, GND, NC, TX, RX from SoC side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WG800HP 2. Connect power cable to WG800HP and turn on it 3. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix pinmux reg value for QCA956xINAGAKI Hiroshi2018-12-241-1/+1
| | | | | | | | | | | | | The range of pinmux reg property "<0x1804002c 0x40>" for QCA956x SoC does not includes GPIO_FUNCTION register. If the device uses "&jtag_disable_pins", this causes the following errors: [ 1.982937] pinctrl-single 1804002c.pinmux: mux offset out of range: 0x40 (0x40) [ 1.990622] pinctrl-single 1804002c.pinmux: could not add functions for pinmux_jtag_disable_pins 64x Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: dts: Remove newly added default-state=off propertyChristian Lamparter2018-12-171-10/+0
| | | | | | I'm afraid that this will be "one of many" patches to come. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: dts: Remove default-state=off property from all gpio LED nodesPetr Štetiar2018-12-1758-192/+0
| | | | | | | | | | | | | | | | | | >From the Documentation/devicetree/bindings/leds/common.txt: - default-state : The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no glitch should be produced where the LED momentarily turns off (or on). The "keep" setting will keep the LED at whatever its current state is, without producing a glitch. The default is off if this property is not present. So setting the default-state of the LEDs to `off` is redundant as `off` is default LED state anyway. We should remove it as almost every new PR/patch submission contains this property by default which seems to be just copy&paste from some DTS file already present in the tree. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link Archer A7Karl-Felix Glatzer2018-12-172-0/+252
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
* ath79, brcm63xx: Fix debounce-interval properties in gpio-keys-polled nodesPetr Štetiar2018-12-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes wrong usage of debounce-interval subnode property of gpio-keys-polled nodes, which was used inproperly in parent node, but it belongs to the subnodes, excerpt from the docs: Optional subnode-properties: - debounce-interval: Debouncing interval time in milliseconds. If not specified defaults to 5. And the docs are up to date as the source code matches that description as well: if (fwnode_property_read_u32(child, "debounce-interval", &button->debounce_interval)) button->debounce_interval = 5; While at it, I've also re-formatted gpio-keys-polled nodes, usually just adding new lines after every key subnode. Cc: Tomasz Maciej Nowak <tomek_n@o2.pl> Cc: Matt Merhar <mattmerhar@protonmail.com> Cc: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add d-link dir-825-c1 and dir-835-a1Sebastian Kemper2018-12-173-0/+277
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79. They're pretty much identical, except dir-835-a1 has less LEDs. The routers come with 128 MByte of RAM and 16 MBytes of flash and sport 2.4GHz and 5.0GHz wireless. Both routers have entries already in OpenWrt's TOH. Please check there for more information on these antiquities. https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1 https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1 Installation: 1. Connect to the web interface of the vendor firmware (usually listening on 192.168.0.1). 2. Go to "Tools", then "Firmware". 3. In the "Firmware Upgrade" box click "Browse". 4. Select the OpenWrt factory image for your router. 5. Click "Upload", confirm the popups if you agree to flash the file you selected. 6. Wait for firmware upgrade to complete. It takes about 5 minutes. Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't have this router so I can't confirm. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
* ath79: add support for TP-Link TL-WR842N/ND v1 routerMarcin Jurkowski2018-12-151-0/+164
| | | | | | | | | | | | | | | | | | This ports support for TP-Link TL-WR842N/ND v1 from ar71xx. CPU: Atheros AR7241 400 MHz RAM: 32 MiB FLASH: 8 MiB PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan WiFi: Atheros AR9287 LED: SYS, WiFi, LAN, WAN, 3G, QSS BTN: WiFi, Reset/WPS AR71xx target used "tl-mr3420" as board id so force flag is needed if upgrading from old target. Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
* ath79: fix dtc compiler warningsMathias Kresin2018-12-123-7/+7
| | | | | | | | | | | | The qca9557/qca956x reset-controller aren't a simple bus. A simple bus would require node unit addresses. Add the node unit addresses for the qca9557 usb phys. Add the regs for the USB_PWRCTL and USB_CONFIG registers even not yet used. Fix the wrong ar7100 pcie controller node unit address as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: dts: Use PowerCloud CAP324 bicolor status LEDDaniel F. Dickinson2018-12-061-3/+3
| | | | | | | | | PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files / base files support using both colours to better inform user of state and to better match stock firmware, so use green power to indicate normal operation. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ath79: add support for I-O DATA WN-AG300DGRINAGAKI Hiroshi2018-12-061-0/+222
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Winchannel WB2000Chuanhong Guo2018-12-061-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WB2000 is a dual-band 11N AP using AR9344. The factory firmware used the original DB120 partition table with a small kernel partition at the end of firmware and the kernel will easily get oversized in the future. Since it has to be flashed using UART I also swapped kernel/rootfs and changed the default load address. Specification: - SoC: Atheros AR9344 - RAM: 128 MB - Flash: 16 MB - Ethernet: 10/100/1000 Mbps (Atheros AR8035) - 2x USB 2.0 - WIFI: AR9344(2G) + AR9382(5G) - RTC: DS1338 Known issue: 5G ath9k led doesn't work due to commit ccab68f. Flash instruction: Set up a TFTP server on your computer and configure static IP. Connect UART (J11 TX/GND/RX) and press any key to enter U-boot shell. 1. Change the default boot command: setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000' saveenv 2. Set your router ipaddr and server ipaddr. e.g.: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.50 3. Load and flash the firmware: tftp 0x80060000 fw.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 4. Reset your router: reset Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [Drop the i2c node unit address. Move the ath9k-leds node out of the spi node, it doesn't belong there. Add the #gpio-cells property to the pci wifi node. All fix dtc compiler warnings] Signed-off-by: Mathias Kresin <dev@kresin.me> merge
* ath79: fix ethernet configurations for I-O DATA ETG3-RINAGAKI Hiroshi2018-12-061-1/+13
| | | | | | | | | | | | This commit fixes several issues in eth0 on ETG3-R, and solve slowdown in NA(P)T speed. - add gmac-config with correct configurations - fix pll-data value And I added ref clock-frequency. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix GL.iNet GL-AR300M sysupgradeMathias Kresin2018-12-063-3/+10
| | | | | | | | | | | The userspace boardname derived from the dts compatible was out of sync with the expected board added to the image metadata. This way a sysupgrade is refused. Sync the userspace boardname and the baordname used in the image metdata to allow a seamless sasupgrade. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add SoC or family compatibleMathias Kresin2018-12-0626-30/+24
| | | | | | | Add missing SoC specific compatibles and/or inherit the family compatibles like "ubnt,xm". Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add AVM EVA firmware partition compatibleDavid Bauer2018-12-062-0/+2
| | | | | | | | | | This commit adds firmware partition compatible for the AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E. This allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Define firmware partition format to all boards where applicablePetr Štetiar2018-12-0637-0/+37
| | | | | | | | | | Parsing "firmware" partition (to create kernel + rootfs) was implemented using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With recent upstream mtd changes we can do it in a more clean way for DTS targets. It just requires adding a proper "compatible" string to the "firmware" partition node. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: rename qca9533.dtsi to qca953x.dtsiChuanhong Guo2018-12-066-8/+8
| | | | | | | | | qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE. Rename the misleading dtsi names and fix the SoC type of gl-ar300m. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [apply the changes for the gl-x750 as well] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Ubiquiti AirRouterRussell Senior2018-12-031-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Indoor low-power router with 2.4 GHz radio CPU: Atheros AR7241 rev 1 RAM: 32 MB Flash: 8 MB NOR SPI Switch: Atheros AR7240 Ports: 1x WAN, 4x LAN 10/100 Ethernet WLAN: Atheros AR9285 (2.4 GHz) USB: 1x USB2 host port Note: Ethernet WAN/LAN port naming is reversed from ar71xx. WAN is eth0; LAN is eth1.1. UART settings: 115200, 8N1 LEDs +-------------------------- | | | | | | | | VCC | x x RX | * x | x x | x x TX | * x GND | * x | | | | +-------------------------- ETHERNET PORTS Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: split ubnt outdoor device leds into separate dtsiRussell Senior2018-12-035-31/+39
| | | | | | Move common LED configuration into a separate includible dtsi. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: ubnt-xw: Change DTS license to GPL-2.0-or-later OR MITPetr Štetiar2018-11-291-1/+1
| | | | | | | | Having MIT as alternative is sometimes preferred by upstream maintainers and allows sharing that simple code with other projects. We don't really want multiple DTS versions for the same device. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Change DTS license to GPL-2.0-or-later OR MITPetr Štetiar2018-11-291-1/+1
| | | | | | | | Having MIT as alternative is sometimes preferred by upstream maintainers and allows sharing that simple code with other projects. We don't really want multiple DTS versions for the same device. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for ROSINSON WR818 boardRosy Song2018-11-271-0/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ROSINSON WR818 WiFi-Router SoC: Qualcomm Atheros QCA9563, FLASH: Winbond W25Q128FV 16MBytes, WiFi: QCA9563 b/g/n 3x3 450Mbit/s, USB: 1x USB 2.0 Type A, 1x USB2.0 Type C, IN: WPS/Reset button GPIO1, OUT: Power LED red, Internet LED red, WLAN LED red, LAN1 LED red, LAN2 LED red, System LED red, UART: RX-GPIO18, TX-GPIO22, Tested and working: - Ethernet (LAN + WAN) - WiFi - OpenWRT sysupgrade - Button - LEDs Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.1.1 - Go to "Administration" -> "Firmware Upgrade" - Upload the OpenWrt sysupgrade image Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ath79: merge glinet gl-x750 dtsi and dtsMathias Kresin2018-11-272-101/+97
| | | | | | | | | The board doesn't come in different flash type flavours, hence there is no need to keep a dtsi + dts for this purpose. While at it, fix some whitespace issues. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: rename glinet x750Mathias Kresin2018-11-272-1/+1
| | | | | | The boardname is gl-x750 and is already used for the led names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add Archer C58/C59 partition compatibleDavid Bauer2018-11-262-0/+2
| | | | | | | | | | This commit adds firmware partition compatible for the TP-Link Archer C58 v1 and Archer C59 v1. Since a22311e this allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add firmware partition compatible for OCEDODavid Bauer2018-11-262-0/+2
| | | | | | | | | | This commit adds firmware partition compatible for the OCEDO Raccoon and OCEDO Koala. Since a22311e this allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: specify "firmware" partition format for I-O DATA devicesINAGAKI Hiroshi2018-11-262-0/+2
| | | | | | | | | | | | Specify firmware partition format (denx,uimage) by compatible string for I-O DATA devices. affected devices (&run tested) - WN-AC1167DGR - WN-AC1600DGR2 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: specify "firmware" partition format for ELECOM WRC-300GHBK2-IINAGAKI Hiroshi2018-11-261-0/+1
| | | | | | | Specify firmware partition format (denx,uimage) by compatible string for ELECOM WRC-300GHBK2-I. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: modify mtd partitions for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-11-261-8/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and move it to generic subtarget. In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs" partition in the stock firmware. This causes the size of the kernel to be limited by the fixed value. 0x50000 0xe80000 0xff0000 +-------------------------------+--------------+ | rootfs | kernel | | (14528k) | (1472k) | +-------------------------------+--------------+ After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2 exceeded the limit, and it breaks builds on official buildbot. Since this issue was also confirmed in ath79, I modified the mtd partitions to get rid of that limitation. 0x50000 0xff0000 +----------------------------------------------+ | firmware | | (16000k) | +----------------------------------------------+ However, this commit breaks compatibility with ar71xx firmware, so I dropped "SUPPORTED_DEVICES += bhr-4grv2". This commit requires new flash instruction instead of the old one. Flash instruction using initramfs image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Set the IP address of the computer to 192.168.12.10 3. Rename the OpenWrt initramfs image to "bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP directory 4. Start the tftp server on the computer 5. While holding down the "ECO" button, connect power cable to BHR-4GRV2 and turn on it 6. Flashing (orange) diag LED and release the finger from the button, BHR-4GRV2 downloads the intiramfs image from TFTP server and boot with it 7. On the initramfs image, create "/etc/fw_env.config" file with following contents /dev/mtd1 0x0 0x10000 0x10000 8. Execute following commands to add environment variables for u-boot fw_setenv ipaddr 192.168.12.1 fw_setenv serverip 192.168.12.10 fw_setenv ethaddr 00:aa:bb:cc:dd:ee fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" 9. Perform sysupgrade with squashfs-sysupgrade image 10. Wait ~150 seconds to complete flashing And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC, not QCA9558. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: specify "firmware" partition format for Buffalo devicesINAGAKI Hiroshi2018-11-264-0/+4
| | | | | | | | | | | | | | Specify firmware partition format (denx,uimage) by compatible string for Buffalo devices. affected devices (&run tested): - BHR-4GRV - WHR-G301N - WZR-HP-AG300H - WZR-HP-G302H A1A0 - WZR-HP-G450H (WZR-450HP) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Archer C58/C59 v1David Bauer2018-11-263-0/+381
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Archer C58 v1 and C59 v1, previously supported in the ar71xx target. CPU: Qualcomm QCA9561 RAM: 64M (C58) / 128M (C59) FLASH: 8M (C58) / 16M (C59) WiFi: QCA9561 bgn 3x3:3 QCA9888 nac 2x2:2 LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS Only C59: USB BTN: WPS, WiFi, Reset Installation ------------ Via Web-UI: Update factory image via Web-UI. Via TFTP: Rename factory image to "tp_recovery.bin" and place it in the root-dir of your tftp server. Configure to listen on 192.168.0.66. Power up the router while holding down the reset-button. The router will flash itself and reboot. Note: For TFTP, you might need a switch between router and computer, as link establishment might take to long. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for GL-iNet GL-X750Luo chongjun2018-11-262-0/+141
| | | | | | | | | | | | | | | | | | | this patch adds supports for GL-X750. Specification: - SOC: QCA9531 (650MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 10/100: 1xLAN + 10/100: 1xWAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x reset button - LED: 5x LEDS (green) Flash instruction: The original firmware is openwrt, so both LuCI or sysupgrade can be used. Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
* ath79: Add support for Ubiquity Bullet M (XW)Petr Štetiar2018-11-262-0/+153
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: specify "firmware" partition format for Ubiquiti UniFiRafał Miłecki2018-11-241-0/+1
| | | | | | | | | | | | This affects: 1. Ubiquiti UniFi-AC-LITE/LR 2. Ubiquiti UniFi-AC-PRO 3. Ubiquiti UniFi-AC-MESH 4. Ubiquiti UniFi-AC-MESH PRO Succesfully tested on UniFi AP AC Pro. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for WNDR3700 and v2Hannu Nyman2018-11-242-0/+2
| | | | | | | | Specify the new "firmware" partition format for Netgear WNDR3700 and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third device in the family. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: specify "firmware" partition format for TP-LINK Archer C7 v2Rafał Miłecki2018-11-241-1/+2
| | | | | | With this change it doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for Netgear WNDR3800Rafał Miłecki2018-11-241-0/+1
| | | | | | It doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: fix PQI Air Pen supportMathias Kresin2018-10-281-0/+0
| | | | | | Use the correct dts filename. It has to be <soc>_<manufacturer>_<device>. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for PQI Air PenYuheiOKAWA2018-10-281-0/+147
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: AR9330 (or AR9331 revision?) Ethernet x1, Wireless 2.4G, uSD card slot x1. USB Power, include Li-Po Battery. Flash 8MiB. (factory is dual image) 1. write image is use half 4MiB size from factory. write initramfs image to mtd6 and mtd7. 2. change next boot setting. next is mtd6 boot. echo -ne "\x01" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0 3. rewrite sysupgrade image. change next boot setting. next is mtd4. echo -ne "\x00" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0 OEM mtd. dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00010000 00010000 "ART" mtd3: 00010000 00010000 "NVRAM" mtd4: 00140000 00010000 "uImage" mtd5: 00280000 00010000 "rootfs" mtd6: 00140000 00010000 "uImage2" mtd7: 00280000 00010000 "rootfs2" mtd8: 00010000 00010000 "CONF" Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
* ath79: Add support for Ubiquiti LiteAP ac (LAP-120)Roger Pueyo Centelles2018-10-281-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add support for TP-Link TL-WA901ND v2David Bauer2018-10-071-0/+131
| | | | | | | | | | | | | | | | | | This commit adds support for the TP-Link TL-WR901ND v2 access point. CPU: Atheros AR9132 400MHz RAM: 32MB FLASH: 4MiB WiFi: Atheros AR9103 3x3:2 bgn LED: Power (static on) LAN (controlled by PHY) SYS, WiFi, QSS toggleable BTN: Reset, QSS Installation: Upload the factory image via the vendor-GUI. Signed-off-by: David Bauer <mail@david-bauer.net>