aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/dts
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: add d-link dir-825-c1 and dir-835-a1Sebastian Kemper2018-12-173-0/+277
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79. They're pretty much identical, except dir-835-a1 has less LEDs. The routers come with 128 MByte of RAM and 16 MBytes of flash and sport 2.4GHz and 5.0GHz wireless. Both routers have entries already in OpenWrt's TOH. Please check there for more information on these antiquities. https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1 https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1 Installation: 1. Connect to the web interface of the vendor firmware (usually listening on 192.168.0.1). 2. Go to "Tools", then "Firmware". 3. In the "Firmware Upgrade" box click "Browse". 4. Select the OpenWrt factory image for your router. 5. Click "Upload", confirm the popups if you agree to flash the file you selected. 6. Wait for firmware upgrade to complete. It takes about 5 minutes. Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't have this router so I can't confirm. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
* ath79: add support for TP-Link TL-WR842N/ND v1 routerMarcin Jurkowski2018-12-151-0/+164
| | | | | | | | | | | | | | | | | | This ports support for TP-Link TL-WR842N/ND v1 from ar71xx. CPU: Atheros AR7241 400 MHz RAM: 32 MiB FLASH: 8 MiB PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan WiFi: Atheros AR9287 LED: SYS, WiFi, LAN, WAN, 3G, QSS BTN: WiFi, Reset/WPS AR71xx target used "tl-mr3420" as board id so force flag is needed if upgrading from old target. Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
* ath79: fix dtc compiler warningsMathias Kresin2018-12-123-7/+7
| | | | | | | | | | | | The qca9557/qca956x reset-controller aren't a simple bus. A simple bus would require node unit addresses. Add the node unit addresses for the qca9557 usb phys. Add the regs for the USB_PWRCTL and USB_CONFIG registers even not yet used. Fix the wrong ar7100 pcie controller node unit address as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: dts: Use PowerCloud CAP324 bicolor status LEDDaniel F. Dickinson2018-12-061-3/+3
| | | | | | | | | PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files / base files support using both colours to better inform user of state and to better match stock firmware, so use green power to indicate normal operation. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ath79: add support for I-O DATA WN-AG300DGRINAGAKI Hiroshi2018-12-061-0/+222
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Winchannel WB2000Chuanhong Guo2018-12-061-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WB2000 is a dual-band 11N AP using AR9344. The factory firmware used the original DB120 partition table with a small kernel partition at the end of firmware and the kernel will easily get oversized in the future. Since it has to be flashed using UART I also swapped kernel/rootfs and changed the default load address. Specification: - SoC: Atheros AR9344 - RAM: 128 MB - Flash: 16 MB - Ethernet: 10/100/1000 Mbps (Atheros AR8035) - 2x USB 2.0 - WIFI: AR9344(2G) + AR9382(5G) - RTC: DS1338 Known issue: 5G ath9k led doesn't work due to commit ccab68f. Flash instruction: Set up a TFTP server on your computer and configure static IP. Connect UART (J11 TX/GND/RX) and press any key to enter U-boot shell. 1. Change the default boot command: setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000' saveenv 2. Set your router ipaddr and server ipaddr. e.g.: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.50 3. Load and flash the firmware: tftp 0x80060000 fw.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 4. Reset your router: reset Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [Drop the i2c node unit address. Move the ath9k-leds node out of the spi node, it doesn't belong there. Add the #gpio-cells property to the pci wifi node. All fix dtc compiler warnings] Signed-off-by: Mathias Kresin <dev@kresin.me> merge
* ath79: fix ethernet configurations for I-O DATA ETG3-RINAGAKI Hiroshi2018-12-061-1/+13
| | | | | | | | | | | | This commit fixes several issues in eth0 on ETG3-R, and solve slowdown in NA(P)T speed. - add gmac-config with correct configurations - fix pll-data value And I added ref clock-frequency. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix GL.iNet GL-AR300M sysupgradeMathias Kresin2018-12-063-3/+10
| | | | | | | | | | | The userspace boardname derived from the dts compatible was out of sync with the expected board added to the image metadata. This way a sysupgrade is refused. Sync the userspace boardname and the baordname used in the image metdata to allow a seamless sasupgrade. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add SoC or family compatibleMathias Kresin2018-12-0626-30/+24
| | | | | | | Add missing SoC specific compatibles and/or inherit the family compatibles like "ubnt,xm". Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add AVM EVA firmware partition compatibleDavid Bauer2018-12-062-0/+2
| | | | | | | | | | This commit adds firmware partition compatible for the AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E. This allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Define firmware partition format to all boards where applicablePetr Štetiar2018-12-0637-0/+37
| | | | | | | | | | Parsing "firmware" partition (to create kernel + rootfs) was implemented using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With recent upstream mtd changes we can do it in a more clean way for DTS targets. It just requires adding a proper "compatible" string to the "firmware" partition node. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: rename qca9533.dtsi to qca953x.dtsiChuanhong Guo2018-12-066-8/+8
| | | | | | | | | qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE. Rename the misleading dtsi names and fix the SoC type of gl-ar300m. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [apply the changes for the gl-x750 as well] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Ubiquiti AirRouterRussell Senior2018-12-031-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Indoor low-power router with 2.4 GHz radio CPU: Atheros AR7241 rev 1 RAM: 32 MB Flash: 8 MB NOR SPI Switch: Atheros AR7240 Ports: 1x WAN, 4x LAN 10/100 Ethernet WLAN: Atheros AR9285 (2.4 GHz) USB: 1x USB2 host port Note: Ethernet WAN/LAN port naming is reversed from ar71xx. WAN is eth0; LAN is eth1.1. UART settings: 115200, 8N1 LEDs +-------------------------- | | | | | | | | VCC | x x RX | * x | x x | x x TX | * x GND | * x | | | | +-------------------------- ETHERNET PORTS Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: split ubnt outdoor device leds into separate dtsiRussell Senior2018-12-035-31/+39
| | | | | | Move common LED configuration into a separate includible dtsi. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: ubnt-xw: Change DTS license to GPL-2.0-or-later OR MITPetr Štetiar2018-11-291-1/+1
| | | | | | | | Having MIT as alternative is sometimes preferred by upstream maintainers and allows sharing that simple code with other projects. We don't really want multiple DTS versions for the same device. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Change DTS license to GPL-2.0-or-later OR MITPetr Štetiar2018-11-291-1/+1
| | | | | | | | Having MIT as alternative is sometimes preferred by upstream maintainers and allows sharing that simple code with other projects. We don't really want multiple DTS versions for the same device. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for ROSINSON WR818 boardRosy Song2018-11-271-0/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ROSINSON WR818 WiFi-Router SoC: Qualcomm Atheros QCA9563, FLASH: Winbond W25Q128FV 16MBytes, WiFi: QCA9563 b/g/n 3x3 450Mbit/s, USB: 1x USB 2.0 Type A, 1x USB2.0 Type C, IN: WPS/Reset button GPIO1, OUT: Power LED red, Internet LED red, WLAN LED red, LAN1 LED red, LAN2 LED red, System LED red, UART: RX-GPIO18, TX-GPIO22, Tested and working: - Ethernet (LAN + WAN) - WiFi - OpenWRT sysupgrade - Button - LEDs Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.1.1 - Go to "Administration" -> "Firmware Upgrade" - Upload the OpenWrt sysupgrade image Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ath79: merge glinet gl-x750 dtsi and dtsMathias Kresin2018-11-272-101/+97
| | | | | | | | | The board doesn't come in different flash type flavours, hence there is no need to keep a dtsi + dts for this purpose. While at it, fix some whitespace issues. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: rename glinet x750Mathias Kresin2018-11-272-1/+1
| | | | | | The boardname is gl-x750 and is already used for the led names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add Archer C58/C59 partition compatibleDavid Bauer2018-11-262-0/+2
| | | | | | | | | | This commit adds firmware partition compatible for the TP-Link Archer C58 v1 and Archer C59 v1. Since a22311e this allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add firmware partition compatible for OCEDODavid Bauer2018-11-262-0/+2
| | | | | | | | | | This commit adds firmware partition compatible for the OCEDO Raccoon and OCEDO Koala. Since a22311e this allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: specify "firmware" partition format for I-O DATA devicesINAGAKI Hiroshi2018-11-262-0/+2
| | | | | | | | | | | | Specify firmware partition format (denx,uimage) by compatible string for I-O DATA devices. affected devices (&run tested) - WN-AC1167DGR - WN-AC1600DGR2 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: specify "firmware" partition format for ELECOM WRC-300GHBK2-IINAGAKI Hiroshi2018-11-261-0/+1
| | | | | | | Specify firmware partition format (denx,uimage) by compatible string for ELECOM WRC-300GHBK2-I. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: modify mtd partitions for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-11-261-8/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and move it to generic subtarget. In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs" partition in the stock firmware. This causes the size of the kernel to be limited by the fixed value. 0x50000 0xe80000 0xff0000 +-------------------------------+--------------+ | rootfs | kernel | | (14528k) | (1472k) | +-------------------------------+--------------+ After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2 exceeded the limit, and it breaks builds on official buildbot. Since this issue was also confirmed in ath79, I modified the mtd partitions to get rid of that limitation. 0x50000 0xff0000 +----------------------------------------------+ | firmware | | (16000k) | +----------------------------------------------+ However, this commit breaks compatibility with ar71xx firmware, so I dropped "SUPPORTED_DEVICES += bhr-4grv2". This commit requires new flash instruction instead of the old one. Flash instruction using initramfs image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Set the IP address of the computer to 192.168.12.10 3. Rename the OpenWrt initramfs image to "bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP directory 4. Start the tftp server on the computer 5. While holding down the "ECO" button, connect power cable to BHR-4GRV2 and turn on it 6. Flashing (orange) diag LED and release the finger from the button, BHR-4GRV2 downloads the intiramfs image from TFTP server and boot with it 7. On the initramfs image, create "/etc/fw_env.config" file with following contents /dev/mtd1 0x0 0x10000 0x10000 8. Execute following commands to add environment variables for u-boot fw_setenv ipaddr 192.168.12.1 fw_setenv serverip 192.168.12.10 fw_setenv ethaddr 00:aa:bb:cc:dd:ee fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" 9. Perform sysupgrade with squashfs-sysupgrade image 10. Wait ~150 seconds to complete flashing And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC, not QCA9558. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: specify "firmware" partition format for Buffalo devicesINAGAKI Hiroshi2018-11-264-0/+4
| | | | | | | | | | | | | | Specify firmware partition format (denx,uimage) by compatible string for Buffalo devices. affected devices (&run tested): - BHR-4GRV - WHR-G301N - WZR-HP-AG300H - WZR-HP-G302H A1A0 - WZR-HP-G450H (WZR-450HP) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Archer C58/C59 v1David Bauer2018-11-263-0/+381
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Archer C58 v1 and C59 v1, previously supported in the ar71xx target. CPU: Qualcomm QCA9561 RAM: 64M (C58) / 128M (C59) FLASH: 8M (C58) / 16M (C59) WiFi: QCA9561 bgn 3x3:3 QCA9888 nac 2x2:2 LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS Only C59: USB BTN: WPS, WiFi, Reset Installation ------------ Via Web-UI: Update factory image via Web-UI. Via TFTP: Rename factory image to "tp_recovery.bin" and place it in the root-dir of your tftp server. Configure to listen on 192.168.0.66. Power up the router while holding down the reset-button. The router will flash itself and reboot. Note: For TFTP, you might need a switch between router and computer, as link establishment might take to long. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for GL-iNet GL-X750Luo chongjun2018-11-262-0/+141
| | | | | | | | | | | | | | | | | | | this patch adds supports for GL-X750. Specification: - SOC: QCA9531 (650MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 10/100: 1xLAN + 10/100: 1xWAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x reset button - LED: 5x LEDS (green) Flash instruction: The original firmware is openwrt, so both LuCI or sysupgrade can be used. Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
* ath79: Add support for Ubiquity Bullet M (XW)Petr Štetiar2018-11-262-0/+153
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: specify "firmware" partition format for Ubiquiti UniFiRafał Miłecki2018-11-241-0/+1
| | | | | | | | | | | | This affects: 1. Ubiquiti UniFi-AC-LITE/LR 2. Ubiquiti UniFi-AC-PRO 3. Ubiquiti UniFi-AC-MESH 4. Ubiquiti UniFi-AC-MESH PRO Succesfully tested on UniFi AP AC Pro. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for WNDR3700 and v2Hannu Nyman2018-11-242-0/+2
| | | | | | | | Specify the new "firmware" partition format for Netgear WNDR3700 and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third device in the family. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: specify "firmware" partition format for TP-LINK Archer C7 v2Rafał Miłecki2018-11-241-1/+2
| | | | | | With this change it doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for Netgear WNDR3800Rafał Miłecki2018-11-241-0/+1
| | | | | | It doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: fix PQI Air Pen supportMathias Kresin2018-10-281-0/+0
| | | | | | Use the correct dts filename. It has to be <soc>_<manufacturer>_<device>. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for PQI Air PenYuheiOKAWA2018-10-281-0/+147
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: AR9330 (or AR9331 revision?) Ethernet x1, Wireless 2.4G, uSD card slot x1. USB Power, include Li-Po Battery. Flash 8MiB. (factory is dual image) 1. write image is use half 4MiB size from factory. write initramfs image to mtd6 and mtd7. 2. change next boot setting. next is mtd6 boot. echo -ne "\x01" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0 3. rewrite sysupgrade image. change next boot setting. next is mtd4. echo -ne "\x00" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0 OEM mtd. dev: size erasesize name mtd0: 00040000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00010000 00010000 "ART" mtd3: 00010000 00010000 "NVRAM" mtd4: 00140000 00010000 "uImage" mtd5: 00280000 00010000 "rootfs" mtd6: 00140000 00010000 "uImage2" mtd7: 00280000 00010000 "rootfs2" mtd8: 00010000 00010000 "CONF" Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
* ath79: Add support for Ubiquiti LiteAP ac (LAP-120)Roger Pueyo Centelles2018-10-281-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add support for TP-Link TL-WA901ND v2David Bauer2018-10-071-0/+131
| | | | | | | | | | | | | | | | | | This commit adds support for the TP-Link TL-WR901ND v2 access point. CPU: Atheros AR9132 400MHz RAM: 32MB FLASH: 4MiB WiFi: Atheros AR9103 3x3:2 bgn LED: Power (static on) LAN (controlled by PHY) SYS, WiFi, QSS toggleable BTN: Reset, QSS Installation: Upload the factory image via the vendor-GUI. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Buffalo WZR-HP-G302H A1A0INAGAKI Hiroshi2018-10-071-0/+245
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros AR7242. It is Japanese market model of WZR-HP-G300NH2, but there are some diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx. And, G302H has several hardware versions and hardware is different dependent on the versions. This commit adds support for "A1A0" version. Specification: - Atheros AR7242 - 64 MB of RAM (DDR2) - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 2.4 GHz 2T2R wifi - Atheros AR9283 - 5x 10/100/1000 Mbps Ethernet - Atheros AR8316 - 7x LEDs, 5x keys - LED: 1x gpio-leds, 6x ath9k-leds - key: 3x buttons, 2x slide switches - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/" and move to firmware update page ("ファーム更新") 3. Select the OpenWrt factory image and click update ("更新実行") button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Add support for TP-Link TL-WR842N-v2Robert Marko2018-10-071-0/+204
| | | | | | | | | | | | | | | | | | | | This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79. This is a low cost model with following specs: CPU: Atheros AR9341 SoC RAM: 32 MB DDR1 Flash: 8 MB NOR SPI Switch: Internal AR9341 5 port 10/100 Mbit Ports: 5x 10/100 Mbit(1x WAN, 4x LAN) USB: 1x USB2.0 WLAN: 2.4 GHZ AR9341 Installation: Simply flash the factory image through stock firmware WEB UI. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath79: Add support for Ubiquiti Nanostation ACTobias Schramm2018-10-071-0/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: Add support for Ubiquiti NanoStation AC locoTobias Schramm2018-10-071-0/+40
| | | | | | | | | | | | | | | | | | | | | | | Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: Add generic device tree for Ubiquiti WA boardsTobias Schramm2018-10-071-0/+92
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: fix MAC address for Buffalo BHR-4GRVINAGAKI Hiroshi2018-10-073-2/+8
| | | | | | | | | | | | | | | | | | I added mtd-mac-address for WZR-HP-G450H and BHR-4GRV in 1df1ea4d7e8b6ae3351780ed58800ccd9edd4c27, but that address in ART is incorrect for BHR-4GRV. WZR-HP-G450H has wlan eeprom and MAC address in ART, but BHR-4GRV has only MAC address in ART. - WZR-HP-G450H - eeprom: 0x1000 - MAC: 0x1002 - BHR-4GRV - MAC: 0x0 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Buffalo BHR-4GRVINAGAKI Hiroshi2018-09-261-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV is a wired router, based on Atheros AR7242. Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 2x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the BHR-4GRV normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware upgrade 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix support for Buffalo WZR-HP-G450H and split to dts/dtsiINAGAKI Hiroshi2018-09-262-80/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are many parts that are incorrect or missing in the current code for Buffalo WZR-HP-G450H in ath79, so its support is broken. I fixed that issues and split to dts/dtsi files to add support for Buffalo BHR-4GRV. And WZR-450HP has the same hardware as WZR-HP-G450H, so I change the device name to "WZR-HP-G450H/WZR-450HP". Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 3T3R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 5x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the WZR-HP-G450H (or WZR-450HP) normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix wrong pll-data value for I-O DATA WN-AC-DGR devicesINAGAKI Hiroshi2018-09-261-1/+1
| | | | | | | | The pll-data value "0x56000000" is wrong for I-O DATA WN-AC1600DGR2 and WN-AC1167DGR, so there was a problem of slowing down the speed of ethernet. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Fix GL-AR300M USB triggerRobert Marko2018-09-221-1/+1
| | | | | | Correct a typo preventing USB trigger to work on AR300M. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ath79: flag FritzBox 4020 buttons as active lowDavid Bauer2018-09-221-2/+2
| | | | | | | | | Buttons of AVM FritzBox 4020 are incorrectly flagged as active high. This was an oversight as RFKill button was working as expected even with incorrectly flagged GPIO. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Buffalo WZR-HP-AG300HBernhard Frauendienst2018-09-101-0/+284
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-AG300H is a dual band router based on Qualcom Atheros AR7161 rev 2 Specification: - 680 MHz CPU (Qualcomm Atheros AR7161) - 128 MiB RAM (2x Samsung K4H511638G-LCCC) - 32 MiB Flash (2x Winbond 25Q128BVFG) - WiFi 5 GHz a/n (Atheros AR9220) - WiFi 2.4 GHz b/g/n (Atheros AR9223) - 1000Base-T WAN (Atheros AR7161) - 4x 1000Base-T Switch (Atheros AR8316) - 1x USB 2.0 - 3 Buttons (AOSS/WPS, Reset, USB Eject) - 2 Slide switches (Router (on/off/auto), Movie Engine (on/off)) - 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber, WLAN 5GHz green, WLAN 5GHz LED amber, Router green, Diag red, Movie Engine blue, USB green) It is already supported by the ar71xx target. For more information on the device visit the wiki: <https://openwrt.org/toh/buffalo/wzr-hp-ag300h> Serial console: - The UART Header is next to Movie Engine Switch. - Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V) - The Serial setting is 115200-8-N-1. Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.11.1 - Go to “Administration” → “Firmware Upgrade” - Upload the OpenWrt factory image Tested: - Ethernet (LAN, WAN) - WiFi - Installation - via TFTP rescue - via factory image - on firmware v1.77 (28-05-2012) - on pro firmware v24SP2 r30356 (26-03-2018) - via sysupgrade from ar71xx (wlan devices don't work because of new names) - via sysupgrade from itself - Buttons - LEDS - USB (Power control and device recognition) Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
* ath79: add support for ELECOM WRC-300GHBK2-IINAGAKI Hiroshi2018-09-101-0/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 4x keys(connected to GPIO: 3x) - UART header on PCB - TX, GND, RX, Vcc from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot the WRC-300GHBK2-I normaly and connect the computer to its LAN port 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with squashfs-sysupgrade image for WRC-300GHBK2-I 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for WD My Net Wi-Fi Range ExtenderChristian Lamparter2018-09-101-0/+174
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch ports over support for the device from ar71xx. SOC: AR7370 (Wasp - AR9344 rev2 0001974c) RAM: Winbond W9725G6KB-25 32MiB FLASH: Winbond 25Q64FVSIG 8MiB WLAN: AR9380 Dual-Band 802.11abgn 3x3:3 INPUT: WPS, RESET button (hardware on/off toggle button) LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high) Serial: Header Next to the winbond flash chip (labeld JP1) Pinout is GND - NC - RX - TX - 3V3 (JP1) The Serial setting is 115200-8-N-1. - Installation via uboot's upgrade command 0. attach serial cable 1. interrupt uboot and enter "upgrade code.bin" into the u-boot prompt ar7240> upgrade code.bin 2. rename openwrt...sysupgrade.bin to code.bin on PC 3. run a tftp-client on the PC (shell)$ tftp 192.168.1.230 binary put code.bin 4. wait for the device to finish [...] Copy buff to Flash from 0x9f040000 length 0x79f000 Copy to Flash... write addr: 9f040000 done 5. enter "go" in the u-boot prompt ar7240> go - TFTP ramdisk image boot from the uboot prompt (tftp server defaults to serverip 192.168.1.254) => tftpboot 81000000 initramfs.bin => bootm Tested and working: - LEDs - Buttons - Ethernet - Wi-Fi - OpenWRT sysupgrade For flashing and debricking information see: <https://openwrt.org/toh/wd/rext> Users coming from ar71xx can use sysupgrade too. But I highly advise to no save the old configuration and start from a clean state. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 20:11:34 +0000