aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/dts
Commit message (Collapse)AuthorAgeFilesLines
* ath79: align naming of Ubiquiti Nanostation MSven Roederer2019-03-181-1/+1
| | | | | | | | | | | | | Support for the Nanostation M (XW) was added in 40530c8eb with board name "nanostation-m-xw". The current image for the "Nanostation M" uses "nano-m" as the board name. This commit renames it to the full product name as it's used by all other boards. The legacy boardname of the ar71xx target is added via SUPPORTED_DEVICES to ease switching to ath79 target. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [touch-ups on the commit message, removed subject remains] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for jjPlus JA76PF2Tomasz Maciej Nowak2019-03-181-0/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board. Specification SoC: Atheros AR7161 RAM: 64 MB DDR Flash: 16 MB SPI NOR Ethernet: 2x 10/100/1000 Mbps AR8316 LAN (CN11), WAN/PoE (CN6 - close to power barrel connector, 48 V) MiniPCI: 2x LEDS: 4x, which 3 are GPIO controlled Buttons: 2x GPIO controlled Reset (SW1, closer to ethernet ports), WPS (SW2) Serial: 1x (only RX and TX are wired) baud: 115200, parity: none, flow control: none Currently there is one caveat compared to ar71xx target images as the MAC addresses are random on every reboot. To remedy this one needs to store the WAN MAC address in RedBoot configuration. OpenWrt on first boot, after flashing, will read out the address and assign proper ones to both WAN and LAN ports. It is iportant to NOT keep the old configuration when doing sysupgrade from ar71xx. Upgrading from OpenWrt ar71xx image 1. Connect to serial port, 2. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n <openwrt_sysupgrade_image_name> 3. After writing new image OpenWrt will reboot, now interrupt boot process and enter RedBoot (bootloader) command line by pressing Ctrl+C, 4. Enter following commands (replace variable accordingly), set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_adress> (confirm storing the value by inputting y and pressing Enter) reset 5. Now board should restart and boot OpenWrt with proper MAC addresses. Installation 1. Prepare TFTP server with OpenWrt initramfs image, 2. Connect to WAN ethernet port, 3. Connect to serial port, 4. Power on the board and enter RedBoot (bootloader) command line by pressing Ctrl+C, 5. Enter following commands (replace variables accordingly): set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_address> (confirm storing the value by inputting y and pressing Enter) ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress> load -r -b 0x80060000 <openwrt_initramfs_image_name> exec -c "" 6. Now board should boot OpenWrt initramfs image, 7. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade <openwrt_sysupgrade_image_name> 8. Wait few minutes, after the D2 LED will stop blinking, the board is ready for configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: fix leds description for EnGenius EPG5000Tomasz Maciej Nowak2019-03-181-6/+6
| | | | | | | Align the LEDs deffinition with MACH file present in ar71xx target which has the correct LED functions and colors adescription. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add suport for EnGenius EPG5000Tomasz Maciej Nowak2019-03-131-0/+180
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band wireless router. Specification SoC: Qualcomm Atheros QCA9558 RAM: 256 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled Buttons: 2x GPIO controlled UART: 4 pin header, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Tools > Firmware, 4. Select OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Alternative installation 1. Prepare TFTP server with OpenWrt sysupgrade image, 2. Connect to one of LAN (yellow) ethernet ports, 3. Connect to UART port (leaving out VCC pin!), 4. Power on router, 5. When asked to enter a number 1 or 3 hit 2, this will select flashing image from TFTP server option, 6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8), then router ip (default is 192.168.99.9) and for last, image name downloaded from TFTP server (default is uImageESR1200_1750), 7. After providing all information U-Boot will start flashing the image, You can observe progress on console, it'll take few minutes and when the Power LED will stop blinking, router is ready for configuration. Additional information If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: aigo3d0a0tdagr useful for creating backup of original firmware. When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep the old configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add GL.iNet AR-300M-LiteJeff Kletsky2019-03-134-81/+71
| | | | | | | | | | | | | | | | | | | | | AR300M-Lite is single-Ethernet variant of the AR300M series Its eth0 would otherwise be assigned to the WAN interface making it unreachable firstboot or failsafe. Installation instructions from OEM (OpenWrt variant): * Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI), * Do not preserve settings * Access rebooted device via Ethernet at OpenWrt default address Add previously missing LED defaults for all three variants; -nand, -nor, -lite to the definitions in 01_leds Non-lite variants thanks to Andreas Ziegler https://patchwork.ozlabs.org/patch/1049396/ Runtime-tested: GL.iNet AR300M-Lite Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: add support for LibreRouter v1Santiago Piccinini2019-03-131-0/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: QCA9558 RAM: 128M DDR2 Flash: 16MiB SPI-NOR ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through WiFi2: QCA9558 (bgn) 2T2R WiFi5: 2x mPCIE with AR9582 (an) 2T2R BTN: 1x Reset GPIO: multiple GPIO on header, PoE passthrough enable UART: 3.3V 115200 8N1 header on the board WDG: ATTiny13 watchdog JTAG: header on the board USB: 1x connector and 1x header on the board PoE: 10-32V input in ETH port 1, passthrough in port 2 mPCIE: 2x populated with radios (but replaceable) OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin using the web interface or with sysupgrade -n. Flash from bootloader (in case failsafe does not work) 1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART header in the board. 2. Connect an ETH cable and configure static ip addres 192.168.1.10/24 3. Turn on the device and stop the bootloader sending any key through the serial interface. 4. Use a TFTP server to serve <your image>-sysupgrade.bin file. 5. Execute the following commands at the bootloader prompt: ath> tftp 82000000 <your image>-sysupgrade.bin ath> erase 0x9f050000 +$filesize ath> cp.b 0x82000000 0x9f050000 $filesize ath> bootm 0x9f050000 More docs * Bootloader https://github.com/librerouterorg/u-boot * Board details (schematics, gerbers): https://github.com/librerouterorg/board Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
* ath79: add support for TP-Link RE350K v1Piotr Dymacz2019-03-111-0/+173
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for YunCore A770Piotr Dymacz2019-03-091-0/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE (802.3at) support, based on QCA9531 + QCA9887. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port) - 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA - 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11) - 2x regular LED, 1x RGB LED (all driven by GPIO) - 1x button (reset) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: 1. First, gain root access to the device, following below steps: - Login into web gui (default password/IP: admin/192.168.188.253). - Go to 'Advanced' -> 'Management' -> 'System' and download backup of configuration (bakfile.bin). - Open the file as tar.gz archive, edit/update 'shadow' file and change hash of root password to something known. - Repack the archive, rename it back to 'bakfile.bin' and use to restore configuration of the device. - After that, device will reboot and can be accessed over SSH. 2. Then, install OpenWrt: - Login over SSH and issue command: fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" - Upload 'sysupgrade' image and install it (only if previous command succeeded) with command: 'sysupgrade -n -F openwrt-...'. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: Add support for Ubiquiti Nanostation M (XW)Petr Štetiar2019-03-051-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: qca955x: assert mdio/gmac reset togetherChuanhong Guo2019-03-051-10/+8
| | | | | | | | This allows resetting gmac registers during initialization. Also add compatible string for qca955x mdio to enable more mdio clock dividers. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar934x: assert mac/mdio reset together for gmac0Chuanhong Guo2019-03-051-6/+3
| | | | | | This allows resetting gmac registers during initialization. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: make TP-Link revision naming consistentDavid Bauer2019-03-029-9/+9
| | | | | | | | This commit makes the TP-Link hardware-revision naming consistent to match the one used by the vendor. TP-Link refers to the different revisions as "vX" not "Version X". Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: TP-Link Archer C7 v4 swap usb led namesDavid Santamaría Rogado2019-03-021-2/+2
| | | | | | | | | | | | | | | | Commit 34b10b46 made usb match with the corresponding usb label. The problem is that v4 seems to use in stock firmware the upper led for usb 1 and the lower led for usb 2. The led assigned varies between TP-Link models and even same model versions. For example, Archer C7 v1 and v2 have the leds in the reverse order. Revert 34b10b46 and swap led labels instead, now usb port and led label match and also respect the original behavior. Tested-by: Oldrich Jedlicka <oldium.pro@gmail.com> Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* ath79: add support for TP-Link Archer C5 v1Bart Lauret2019-02-281-0/+46
| | | | | | | | | | | | | | | | | | | | TP-Link Archer C5 v1 is a dual band router based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: - 720 MHz CPU - 128 MB of RAM (Various chips) - 16 MB of FLASH (Various chips) - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi - minipcie slot with 3T3R 5 GHz QCA9880-BR4A - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch) - 10x LEDs, 2x software buttons For further informwation on the device, visit the wiki: <https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500> Signed-off-by: Bart Lauret <bblauret@gmail.com>
* ath79: TP-Link Archer C7 v4 swap usb port ledsDavid Santamaría Rogado2019-02-281-2/+2
| | | | | | | USB 1 triggers usb2 led and USB 2 triggers usb1. Lower LED is usb1 and upper LED usb2. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* ath79: Modify glinet x750 and AR300m MAC address offsetsLuo chongjun2019-02-282-2/+4
| | | | | | | | In the production of glinet, the MAC address of ethernet port is only written at the position where the ART area offset address is 0, and the MAC address of eth1 is added 1 on the basis of eth0. Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
* ath79: add support for COMFAST CF-E120A v3Roger Pueyo Centelles2019-02-281-0/+146
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless CPE with two Ethernet ports and a 802.11an radio. Specifications: - AR9344 SoC - 535/400/267 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 5 GHz, up to 25 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: fix wmac memory region for qca953xChuanhong Guo2019-02-201-1/+1
| | | | | | | According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h the size of wmac register range for qca953x is only 0x20000. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for I-O DATA WN-AC1600DGRINAGAKI Hiroshi2019-02-144-16/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - SoC: Qualcomm Atheros QCA9557 - RAM: 128 MB - Flash: 16 MB - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 5x 10/100/1000 Mbps - Switch: QCA8337N - LED/key: 6x/6x(4x buttons, 1x slide switch) - UART: through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR 2. Connect power cable to WN-AC1600DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Alternative flash instruction using initramfs image: 1. Prepare a computer and TFTP server software with the IP address "192.168.99.8" and renamed OpenWrt initramfs image "uImageWN-AC1600DGR" 2. Connect between WN-AC1600DGR and the computer with UART 3. Connect power cable to WN-AC1600DGR, press "4" on the serial console and enter the U-Boot console 4. execute "tftpboot" command on the console and download initramfs image from the TFTP server 5. execute "bootm" command and boot OpenWrt 6. On initramfs image, download the sysupgrade image to the device and perform sysupgrade with it 7. Wait ~150 seconds to complete flashing This commit also removes unnecessary "qca,no-eeprom" property from the ath10k wifi node. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix qca955x dual pci resource allocationSantiago Piccinini2019-02-141-1/+1
| | | | | | | | Tested with a dual pci QCA9558 board (LibreRouter v1) in three configurations: enabling pcie0 only, pcie1 only and both enabled. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
* ath79: fix qca955x pcie0 memory sizeSantiago Piccinini2019-02-141-1/+1
| | | | | | | | | Datasheet states that both PCI ranges are of 0x2000000 size: 0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Reviewed-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
* ath79: rename TP-LINK to TP-LinkPaul Wassi2019-02-144-4/+4
| | | | | | Remove inconsistencies in the vendor's name. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rename TL-WR740ND-v4 to TL-WR740N-v4Paul Wassi2019-02-141-2/+2
| | | | | | Give the device the same name it had in ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for Xiaomi Mi Router 4QDavid Bauer2019-02-111-0/+153
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9561 RAM: 64M DDR2 FLASH: 16M SPI-NOR ETH: 1x WAN - 2x LAN WiFi: QCA9561 3T3R BTN: 1x Reset - 1x WPS LED: 1x Blue - 1x Red - 1x Yellow UART: TX - GND - RX - VCC (From ethernet port) 115200n8 - 3.3V Installation ------------ 1. Connect to the device via UART. 2. Interrupt the U-Boot on power-on by pressing enter when prompted. 3. Connect you computer to one of the routers LAN ports. Assign yourself the IP 192.168.31.10/24. Copy the OpenWRT initramfs image to a tftp server root directory. Rename the image to 'x4q.bin'. 4. Load the initramfs image to the router by executing following command in U-Boot. The image will boot afterwards. > tftpboot 0x81000000 x4q.bin; bootm 5. SCP the sysupgrade-image into '/tmp'. Remember to assign yourself an IP in 192.168.1.0/24 for this step! 6. Install OpenWRT permanently by executing > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-LINK Archer C7 v4Oldřich Jedlička2019-02-051-0/+271
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the Qualcomm/Atheros QCA9561 SoC + QCA9880. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction: 1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin and rename it to ArcherC7v4_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
* ath79: add support for TP-Link Archer C2 V3 (AC900)Skirmantas Lauzikas2019-01-271-0/+185
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the TP-link Archer C2 V3 (AC900). Specifications: - CPU: QCA9563 750Mhz - Ram: 64MB (DDR2) - Flash: 8MB (SPI NOR) - Ethernet: 5x 10/100/1000 - Wifi: QCA9563 bgn + QCA9887 an+ac - 9x Leds, 2x buttons Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin via the router Web interface and flash as normal firmware update. Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt> [reorder entries, fix trailing whitespace in dts, add firmware partition compatible string, remove led default off states, use default on state for system led, reuse tplink-safeloader-uimage image build recipe, squash with dynamic partitioning commit, reword commit message, add installation instructions] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath79: add support for Devolo WiFi Pro 1750eDjango Armstrong2019-01-261-0/+83
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3) WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3) BTN: 1x Reset 1x WPS 1x USB eject LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports) Dupont 4 pin header Rear RJ45 serial port non-functional USB: 1x v2.0 Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password previously set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
* ath79: dts: Unify naming of gpio-led nodesPetr Štetiar2019-01-268-8/+8
| | | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> [split up, removed entries where it could clash due to ath9k-leds] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: dts: Unify naming of gpio-keys nodesPetr Štetiar2019-01-2613-13/+13
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* ath79: fix GL.iNet AR300M family GPIOs/LEDsJeff Kletsky2019-01-261-14/+2
| | | | | | | | | | | | | | | | | Change the "status" LED to proper GPIO 12 and "red" naming. Remove GPIO 2 from definition as a USB LED. GPIO 2 is used to control power to the USB socket, not an LED. As such, PWM on the line or typical LED triggers are inappropriate. Users who wish to control the USB power for custom applications can manipulate the GPIO through code, or for example, export it through /sys/class/gpio/export. Runtime-tested:  GL.iNet AR300M-Lite Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: add support for devolo WiFi pro 1200iDavid Bauer2019-01-051-0/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1750iDavid Bauer2019-01-051-0/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: align GL-AR750S boardname to other GL.iNet devicesChristoph Krapp2019-01-011-1/+1
| | | | | | As the official device name is GL-AR750S, rename the board accordingly. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: tweak the position of factory partition for wr818Rosy Song2018-12-311-8/+8
| | | | | | | | The 'factory' partition will move to 0x50000-0x60000 in 2019. As the webserver in bootloader is compatible with different mtdlayout, all the users still can upgrade firmware whatever on ath79 or ar71xx. Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ath79: add support for COMFAST CF-E110NRoger Pueyo Centelles2018-12-311-0/+158
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E110N, an outdoor wireless CPE with two Ethernet ports and a 802.11bgn radio. Specifications: - 650/400/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 26 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new want, so a factory reset will be needed: once the new firmware is flashed, perform the factory reset by pushing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing quicker. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Notes: The device is advertised, sold and labeled as "CF-E110N", but the bootloader and the stock firmware identify it as "v2". Acknowledgments: Petr Štetiar <ynezz@true.cz> Sebastian Kemper <sebastian_ml@gmx.net> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [drop unused labels from devicetree source file] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for TP-Link Archer C6 v2Georgi Vlaev2018-12-312-0/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* ath79: add support for EnGenius EWS511APGuan-Hong Lin2018-12-311-0/+144
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EWS511AP is a wireless managed wall AP with PoE support, based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887. Short specification: - 128MB of RAM - 16 MB of SPI FLASH - 2T2R 2.4 GHz (QCA9531), 802.11b/g/n - 1T1R 5 GHz (QCA9887), 802.11ac/n/a - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED - 1x RESET button - built-in watchdog chipset Flash instruction: From EnGenius firmware to OpenWrt firmware: Original firmware is based on QSDK. Use sysupgrade firmware directly in vendor GUI. Reset to factory default is necessary. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the OpenWrt firmware in the root directory on your computer. 2. Power up EWS511AP. Press 4 and then press any key to enter u-boot. 3. Download OpenWrt firmware (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin" 4. Flash the firmware (ath)> erase 0x9f060000 +f50000 (ath)> cp.b $fileaddr 0x9f060000 $filesize 5. Reboot (ath)> reset Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
* ath79: add status LED on GL.iNet AR300MPaul Wassi2018-12-311-1/+8
| | | | | | This adds the triggers for the status LED of this device. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-313-4/+4
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Add support for TP-Link WR810NPaul Wassi2018-12-313-0/+162
| | | | | | Device specifications given in b23b0fb28b760ce66a8f93d4681c8bd300d75d30 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR150Paul Wassi2018-12-311-1/+1
| | | | | | | This device is called GL-AR150, therefore rename the board to 'gl-ar150' Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for ELECOM WRC-1750GHBK2-I/CINAGAKI Hiroshi2018-12-313-138/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac routers, based on Qualcomm Atheros QCA9563. This commit also includes small fix; use "0x0x03000101" as pll_1000 instead of "0x03000000". Specification: - SoC: Qualcom Atheros QCA9563 - RAM: 128 MB (DDR2) - Flash: 16 MB (SPI-NOR) - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 10/100/1000 Mbps - LED/key: 4x/3x (2x buttons, 1x slide-switch) - UART: through-hole on PCB - Vcc, RX, GND, TX from switch (QCA8337N) side - 115200n8 Flash instruction using factory image: 1. Boot WRC-1750GHBK2-I/C normaly 2. Access to "http://192.168.2.1/" and open firmware upgrade page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Fix UBNT Unifi AC LEDsPaul Wassi2018-12-311-2/+2
| | | | | | | Both LEDs on these devices are ACTIVE_HIGH, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: Fix system LED on TP-Link WR740/741 v4Paul Wassi2018-12-311-1/+1
| | | | | | | The system LED on these devices is ACTIVE_LOW, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for TP-Link TL-WR841N/ND v8Antonio Silverio2018-12-311-0/+164
| | | | | | | | | | | | | | | | | | | CPU: Atheros AR9341 535MHz RAM: 32MB FLASH: 4MiB PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan WiFi: Atheros AR9341 2x2:2 bgn LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill BTN: WPS, WiFi, Reset Installation: Upload the factory image via the vendor-GUI. Signed-off-by: Antonio Silverio <menion@gmail.com> [resolve merge conflicts, squash commits, fix commit title, remove default default off led properties, mark sysupgrade image compatible with the ar71xx version of the board, drop blank lines from dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for GL.iNet GL-AR750SChristoph Krapp2018-12-311-0/+154
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now this patch adds nor image generation only. NAND image generation is not supportet at the moment. Furtheremore support for the MicroSD port is not implemented as of now. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x switch button, 1x reset button - LED: 3x LEDS (green) - Another LED can be accessed on GPIO 7 if soldered Flash instruction: - Set static ip to 192.168.1.2 - Unplug the power cord - Hold reset button - Plug power back in - Right led will flash 5 times - Release reset button - Browse to 192.168.1.1 - Choose sysupgrade image in NOR-flash section - Press "update nor firmware" - After successful transfer unplug network cable before device restarts Signed-off-by: Christoph Krapp <achterin@googlemail.com> [resolve merge conflicts, rename buttons, use switch input type for mode switch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix OCEDO Koala ethernet configurationDavid Bauer2018-12-301-11/+1
| | | | | | | | | The OCEDO Koala has incorrect PLL settings which result in ~3% packet loss on ethernet connections. Also omit the gmac-configuration as it's incorrect too. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DIR-859 A1Weijie Gao2018-12-301-0/+177
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: ubnt-bullet-m-xw: Remove eth1 disabled nodePetr Štetiar2018-12-271-4/+0
| | | | | | It's redundant as eth1 is disabled by default in ath79.dtsi. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Move eth0 mtd-mac-address to the common includePetr Štetiar2018-12-272-2/+4
| | | | | | | It's same for Bullet and Nanostation so far, so let's hope it's going to be the same for other boards sharing the same platform. Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-20 03:25:55 +0000