| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the label MAC address for several devices in
ath79.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").
Some measurements performed on TP-Link Archer C7-v5:
mib-type=0, mib-poll-interval=500ms (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.93 0.00 0.00 1.93 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
mib-type=0, mib-poll-interval=2s (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.14 0.00 0.00 1.14 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
| |
This prepares for support of v5.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
| |
Parsing "firmware" partition (to create kernel + rootfs) was implemented
using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With
recent upstream mtd changes we can do it in a more clean way for DTS
targets. It just requires adding a proper "compatible" string to the
"firmware" partition node.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
| |
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.
The existing led sequences should be the same as before.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
| |
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
Fixes spaces vs. tabs issues and remove indentation on blank lines.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
This helps getting rid of SUPPORTED_DEVICES which can be
auto-generated in image/Makefile.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|