aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/config-4.14
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for D-Link DIR-859 A1Weijie Gao2018-12-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: drop unused mtd splitterMathias Kresin2018-12-061-2/+0
| | | | | | | Neither the seama nor the wrgg splitter are used at the moment. Drop them for now to not bloat the target from the beginning. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Buffalo WZR-HP-AG300HBernhard Frauendienst2018-09-101-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-AG300H is a dual band router based on Qualcom Atheros AR7161 rev 2 Specification: - 680 MHz CPU (Qualcomm Atheros AR7161) - 128 MiB RAM (2x Samsung K4H511638G-LCCC) - 32 MiB Flash (2x Winbond 25Q128BVFG) - WiFi 5 GHz a/n (Atheros AR9220) - WiFi 2.4 GHz b/g/n (Atheros AR9223) - 1000Base-T WAN (Atheros AR7161) - 4x 1000Base-T Switch (Atheros AR8316) - 1x USB 2.0 - 3 Buttons (AOSS/WPS, Reset, USB Eject) - 2 Slide switches (Router (on/off/auto), Movie Engine (on/off)) - 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber, WLAN 5GHz green, WLAN 5GHz LED amber, Router green, Diag red, Movie Engine blue, USB green) It is already supported by the ar71xx target. For more information on the device visit the wiki: <https://openwrt.org/toh/buffalo/wzr-hp-ag300h> Serial console: - The UART Header is next to Movie Engine Switch. - Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V) - The Serial setting is 115200-8-N-1. Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.11.1 - Go to “Administration” → “Firmware Upgrade” - Upload the OpenWrt factory image Tested: - Ethernet (LAN, WAN) - WiFi - Installation - via TFTP rescue - via factory image - on firmware v1.77 (28-05-2012) - on pro firmware v24SP2 r30356 (26-03-2018) - via sysupgrade from ar71xx (wlan devices don't work because of new names) - via sysupgrade from itself - Buttons - LEDS - USB (Power control and device recognition) Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
* ath79: port cybertan_part from ar71xxChristian Lamparter2018-09-101-0/+1
| | | | | | | | | | | | | This patch ports the cybertan_part code from ar71xx and converts the driver to a DT-supported mtd parser. As a result, it will no longer add the u-boot, nvram and art partitions, which were never part of the special Cybertan header. Instead these partitions have to be specified in the DT, which has the upside of making it possible to add properties (i.e.: read-only), labels and references to these important partitions. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: disable unused drivers for tiny targetLucian Cristian2018-07-071-8/+0
| | | | | | | | | | | Shrink the tiny kernel by moving all switch and ethernet phy drivers to the generic kernel config instead of the target kernel config. All boards in the tiny and nand target are either ar7240 or ar9331 based, which don't support external xMII and therefore no external ethernet phy can be connected. None of the boards uses a realtek switch either. Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add tl-wr2543-v1 supportLucian Cristian2018-06-261-0/+1
| | | | | | to switch between wlan leds we need a userspace implementation Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: enable rtl8366rb phyLucian Cristian2018-05-221-0/+1
| | | | | | is needed for at least tplink wr1043nd-v1 Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-221-2/+0
| | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ath79: fix TP-Link TL-WR1043ND v1 image buildMatthias Schiffer2018-05-171-0/+1
| | | | | | | | Both initramfs and flashed images are built and boot. No Ethernet, no WLAN, probably further issues, so the image is not added to TARGET_DEVICES for now. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ath79: cleanup kernel configMathias Kresin2018-05-171-4/+1
| | | | | | Remove outdated or not required kernel config settings. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add new OF only target for QCA MIPS siliconJohn Crispin2018-05-071-0/+247
This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>