aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ath79: Correct glinet, gl-ar300m-lite in 02_networkJeff Kletsky2019-09-281-1/+1
| | | | | | | | | | | | | | | Previously, the board name for the GL-AR300M-Lite was incorrect in 02_network, resulting in an unintended, fall-through condition when initializing the network configuration. While builds prior to commit 8dde11d521 (merged June 5, 2019) ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi functioned properly, the error was noted in resolving first-boot connectivity issues related to the single-phy nature of the device and the "swap" of eth0 and eth1 related to that commit. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> (cherry picked from commit 549ea4dc1878d95ee2b752b8840d75a64a67b679)
* ath79: remove invalid uses of ath9k_patch_fw_mac_crcAdrian Schmutzler2019-09-221-3/+3
| | | | | | | | | | | | | Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which is meant to generate a checksum, for fixing their ath9k MAC addresses. However, those do not have a checksum field, and the calculated checksum offset would be negative. This patch will use ath9k_patch_fw_mac function for those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit f8d8b3f85d70a85d4fabc9b8ed4dbc8020be0523)
* treewide: sysupgrade: use $UPGRADE_BACKUP to check for backupRafał Miłecki2019-09-161-2/+2
| | | | | | | | Now that $UPGRADE_BACKUP is set conditionally there is no need to check the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a858db313687ddfa6ed1ddba76bd74844a7b89dc)
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-121-2/+2
| | | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 641f6b6c26cb9ab5e1198810015e5f4b2b5b34ad)
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-09-071-3/+3
| | | | | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 8b4bc7abe073489a3595eeb2d81818852319c148) [rmilecki: dropping ARGV without this change broke sysupgrade] Fixes: 6ac62c4b6cae ("base-files: don't set ARGV and ARGC")
* treewide: fix invalid UPGRADE_OPT_SAVE_CONFIG spellingsRafał Miłecki2019-09-061-2/+2
| | | | | | | | That was a result of accidentally running "sed" twice on some files. Fixes: 9b9412d55cca ("treewide: replace remaining (not working now) $SAVE_CONFIG uses") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 1078de96e315f3cc2675b2c5935009e8c6159ad4)
* treewide: replace remaining (not working now) $SAVE_CONFIG usesRafał Miłecki2019-09-061-2/+2
| | | | | | | | This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG Fixes: f25d164aca80 ("base-files: pass "save_config" option to the "sysupgrade" method") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 5797fe84a3b508483f7d82e177157c1bf2f342d9)
* ath79: Merge cases in 11-ath10k-caldataAdrian Schmutzler2019-09-041-5/+2
| | | | | | | Cosmetical patch that just merges two cases. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 28baaaae82155e7fc695789dd0a807cc2f298be8)
* ath79: Fix whitespace errors in 11-ath10k-caldataAdrian Schmutzler2019-08-271-2/+2
| | | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 1174b94bc98db9730cec8501397cf997b6f7b35c)
* ath79: add support for devolo WiFi pro 1750xDavid Bauer2019-07-212-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED Power (non-controllable) 1x LED Status (internal) 1x LED LAN (controlled by PHY) 1x LED WLAN BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to external-LED header. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit cb3cd526948af3f69da1af18e035177a0a8f58e3)
* ath79: Use -v1 suffix for TP-Link WDR3600/4300Adrian Schmutzler2019-07-172-4/+4
| | | | | | | | | | | | | | | In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have been used while most other TP-Link devices include the revision. Although there actually is only one major revision of these devices, they bear the revision on their bottom (v1.x). TP-Link also refers to the devices as V1 on its web page. This patch thus adds -v1 to both so it is more consistent with other devices and with what you would expect from reading the on-device sticker and the support pages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C25 v1Adrian Schmutzler2019-06-104-9/+19
| | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip, but not all of them as e.g. for the C59. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Reorder some TP-Link Archer devices in 01_ledsAdrian Schmutzler2019-06-101-8/+8
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: migrate Archer C7 5GHz radio device pathsDavid Santamaría Rogado2019-06-101-6/+20
| | | | | | | | | | | | | | | | | | When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79, the 5ghz radio stops working because the device path changed. Some people subtitute the unsupported QCA9880v1 in the Archer v1 with supported QCA9880v2 radio. Since the stock radio doesn't work, so it's safe to apply the change also for the Archer v1 images as well. Also this patch renames the migration file and variables from wmac to wifi. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed comment, added return 0 (not that it matters since uci is clever, see 00-wmac-migration thread), reworded commit message]
* ath79: Consistently label art partition with lower caseAdrian Schmutzler2019-06-103-8/+5
| | | | | | | | This patch harmonizes the label and alias for art partitions across ath79. Since lower case seems to be more frequent, use that consistently. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Read MAC addresses from flash in 11-ath10k-caldataAdrian Schmutzler2019-06-101-14/+23
| | | | | | | | | | In commit c3a8518 eth0 and eth1 have been swapped for some devices, but 11-ath10k-caldata has not been updated. Instead of fixing this by swapping eth0/eth1, this patch will read addresses from flash (as done for several devices already) so adjustments due to eth order become obsolete. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consistently label info partitionAdrian Schmutzler2019-06-101-9/+3
| | | | | | | | | | | | | | | | The info/product-info partition, which frequently contains MAC adresses, is typically assigned the 'info' alias in DTS, but then labelled with 'info', 'product-info' or 'config'. This leads to different aliases if used for setting MAC adresses in DTS compared to when using e.g. mtd_get_mac_binary. Occationally, also multiple switch-case entries are used just because of different labelling. This patch relabels those partitions in ath79 to consistently use 'info'. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for 8devices Carambola2 development boardRytis Zigmantavičius2019-06-051-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Atheros AR9331 (400 MHz) - 64 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 1T1R 2.4 Wlan (AR9331) - 2x 10/100 Mbps Ethernet - 3x LEDs, 1x gpio button - 1x USB 2.0, 5V - UART over usb, 115200n8 Upgrading from ar71xx target: - Put image into board: scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \ root@192.168.1.1/tmp/ - Run sysupgrade sysupgrade /tmp/sysupgrade.bin Upgrading from u-boot: - Set up tftp server with sysupgrade.bin image - Go to u-boot (reboot and press ESC when prompted) - Set TFTP server IP setenv serverip 192.168.1.254 - Set device ip from same subnet setenv ipaddr 192.168.1.1 - Copy new firmware to board tftpboot 0x81000000 sysupgrade.bin - erase flash erase 0x9f050000 +${filesize} - flash firmware cp.b 0x81000000 0x9f050000 ${filesize} - Reset board reset Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com> [wrapped long line in commit description, whitespace and art address fix in DTS, keep default lan/wan setup, removed -n in sysupgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for ZBT-WD323Kristian Evensen2019-06-053-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT-WD323 is a dual-LTE router based on AR9344. The detailed specifications are: * AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN). * 128 MB RAM * 16MB of flash(SPI-NOR, 22MHz) * 1x 2.4GHz wifi (Atheros AR9340) * 3x 10/100Mbos Ethernet (AR8229) * 1x USB2.0 port * 2x miniPCIe-slots (USB2.0 only) * 2x SIM slots (standard size) * 4x LEDs (1 gpio controlled) * 1x reset button * 1x 10 pin terminal block (RS232, RS485, 4x GPIO) * 2x CP210x UART bridge controllers (used for RS232 and RS485) * 1x 2 pin 5mm industrial interface (input voltage 12V~36V) * 1x DC jack * 1x RTC (PCF8563) Tested: - Ethernet switch - Wifi - USB port - MiniPCIe-slots (+ SIM slots) - Sysupgrade - Reset button - RS232 Intallation and recovery: The board ships with OpenWRT, but sysupgrade does not work as a different firmware format than what is expected is generated. The easiest way to install (and recover) the router, is to use the web-interface provided by the bootloader (Breed). While the interface is in Chinese, it is easy to use. First, in order to access the interface, you need to hold down the reset button for around five seconds. Then, go to 192.168.1.1 in your browser. Click on the second item in the list on the left to access the recovery page. The second item on the next page is where you select the firmware. Select the menu item containing "Atheros SDK" and "16MB" in the dropdown close to the buttom, and click on the button at the bottom to start installation/recovery. Notes: * RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1 Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: fix default config for devices with eth0/eth1 swappedChuanhong Guo2019-06-052-70/+56
| | | | | | | | | | | | | | | | also fix the following problems in this commit: glinet,gl-ar150: This router uses an uncommon order of setting up gmacs in ar71xx. gmac0 is preferred to be wan port because of the additional link status info available. So this router will have eth0/eth1 swapped comparing to ar71xx. tplink,tl-wr710n-v1: same as gl-ar150 embeddedwireless,dorin: eth0 is used as switch port, which was incorrect. It's correct now, so keep this one untouched. tplink,tl-wr842n-v1: we don't swap PHYs on ar7241 so the original port order is incorrect. reorder archer-a7-v5 entry. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: rework LED configurations for tplink,archer-d50-v1Chuanhong Guo2019-06-051-3/+3
| | | | | | | | | | | | The original one has the following problem: 1. Port mask of lan led includes wan port. 2. By using netdev trigger with vlan port, the link led is always on. This commits fixes the above problems by correcting port mask for lan led and use swconfig trigger for wan leds. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add leds migrations for archer-c7-v2 and v4David Santamaría Rogado2019-05-311-0/+6
| | | | | | | | | | | | In ar71xx v2 has blue color defined because the same mach-*.c is also used for TL-WDR4900 model with blue leds. ath79 v2 dts defines them as green. For v4 the situation is the same as v5 so the conversion is identical only v4 instead v5. So now upgrading from ar71xx to ath79 should be also smoother for v2 and v4. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
* ath79: add support for WD My Net N750Ryan Mounce2019-05-273-7/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: AR9344 RAM: 128MB Flash: 16MiB Winbond 25Q128BVFG SPI NOR 5GHz WiFi: AR9380 PCIe 3x3:3 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Gigabit ethernet via AR8327N switch (green + amber LEDs) 2x USB 2.0 via GL850G hub 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO Known issues: AR8327N LEDs only have default functionality, not presented in sysfs. This is a regression from ar71xx. UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX See https://openwrt.org/toh/wd/n750 for flashing detail. Procedures unchanged from ar71xx. Tested sysupgrade + factory flash from WD Emergency Recovery Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ath79: add leds migrations for archer-c7-v5Petr Štetiar2019-05-201-0/+3
| | | | | | | | | ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more generic `tplink` as the DTS is reused by more boards, so we need to perform migrations of the LED names during upgrade. Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link Archer D50 V1Davide Fioravanti2019-05-183-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer D50 v1 is a dual-band AC1200 router + modem. The router section is based on Qualcomm/Atheros QCA9531 + QCA9882. The "DSL" section is based on BCM6318 but it's currently not supported. Internally eth0 is connected to the Broadcom CPU. Router section - Specification: CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB) RAM: 64 MB (DDR2) Flash: 8 MB (SPI NOR) Wifi 2.4GHz: QCA9531 2T2R Wifi 5GHz: QCA9982 2T2R 4x 10/100 Mbps Ethernet 8x LED, 3x button UART header on PCB Known issues: DSL not working (eth0) (WIP) UART connection --------------- J2 HEADER (Qualcomm CPU) . TX . RX . GND O VCC J16 HEADER (Broadcom CPU) O VCC . GND . RX . TX The following instructions require a connection to the J2 UART header. Flash instruction under U-Boot, using UART ------------------------------------------ 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Initramfs instruction under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin bootm 0x81000000 Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616 4. Double check the .mod file size. It must be 7995392 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed default-state = "off", it's already the default, added pcie node, fixed typo]
* ath79: add support for Aruba AP-105Chris Blake2019-05-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Atheros AR7161-8C1A @ 680 MHz RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR) WI1: Atheros AR9223-AC1A 802.11bgn WI2: Atheros AR9220-AC1A 802.11an ETH: Atheros AR8021-BL1E + PoE LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G BTN: 1 x Reset I2C: AT97SC4303s TPM (needs driver!) CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud Factory installation: - Needs a u-boot replacement. See Wiki for information on how to do a in-circut flash with a SPI-Flasher like a CH314A or flashrom. Wiki page can be found at https://openwrt.org/toh/aruba/aruba_ap-105 - Be careful when dis- and reassembling the device to not squish any of the antenna cables in the process! - Be sure to make a full 16 MiB backup of your device before flashing the new u-boot! This is needed if you ever have interest in reverting back to stock firmware. Not working: - TPM (needs a driver) Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ath79: Add support for TP-Link TL-WR1043N v5Adrian Schmutzler2019-05-182-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - QCA9563 at 775 MHz - 64 MB RAM Zentel A3R12E40CBF-8E - 16 MB flash Winbond W25Q128FVSG - 3 (non-detachable) Antennas / 450 Mbit - 1x/4x WAN/LAN Gbps Ethernet (QCA8337) - reset and Wi-Fi buttons TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4, except that the USB port has been removed and there is no longer a removable antenna option. It also has different partitioning scheme. The software is more in line with the Archer series in that it uses a nested bootloader scheme. (This has been adapted from the OpenWrt Wiki page) <https://openwrt.org/toh/tp-link/tl-wr1043nd> Installation on HW rev.5: Factory firmware can be installed via the WEB interface. Alternatively, it is also possible to use a TFTP server for recovery purposes: - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin - Set static IP of your PC to *192.168.0.66* - Router will obtain IP 192.168.0.86 for a few seconds while loading, when reset button pressed at power On. And finally, there's always u-boot access through the UART. For information visit the wiki. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworked commit message]
* ath79: add support for EnGenius ECB1750sven friedmann2019-05-184-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - Qualcomm Atheros SoC QCA9558 - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 1x 10/100/1000 Mbps Ethernet - 3T3R 2.4 GHz (QCA9558 WMAC) - 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH) https://fccid.io/A8J-ECB1750 Tested and working: - lan, wireless, leds, sysupgrade (tftp) Flash instructions: 1.) tftp recovery - use a 1GbE switch or direct attached 1GbE link - setup client ip address 192.168.1.10 and start tftpd - save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory - plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed - afterwards login via ssh and do a sysuprade 2.) oem webinterface factory install (not tested) Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin". 3.) oem webinterface command injection OEM Firmware already running OpenWrt (Attitude Adjustment 12.09). Use OEM webinterface and command injection. See wiki for details. https://openwrt.org/toh/engenius/engenius_ecb1750_1 Signed-off-by: sven friedmann <sf.openwrt@okay.ms> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [use interrupt-driven "gpio-keys" binding]
* ath79: add TP-Link WR842N v3Sven Roederer2019-04-132-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the TP-Link WR842N v3 which is already supported on ar71xx target (0b45bec22c59cc6e6b2fa71dc9a88386c5587132). Specification: * SoC: QCA9533 ver 2 rev 0 * 16 MB Flash (gd25q128) * 64 MB RAM * 1 WAN 10/100 MBit/s (blue connector) * 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors) * Atheros AR9531 (2,4GHz, two fixed antennas) * USB * Reset / WPS button * WiFi button (rf kill) * 8 green leds; 1 red/green led * serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed) Installation: * flash via vendor WebUI (the filename must not exceed certain length) * sysupgrade from installed OpenWrt (also ar71xx) Thanks to Holger Drefs for providing the hardware Tested-by: @kofec (github) Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ath79: add support for Netgear EX6400 and EX7300Daniel Gimpelevich2019-04-092-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Correct MAC address for WAN interface of Archer A7/C7 v5Adrian Schmutzler2019-04-081-0/+5
| | | | | | | | | | | These devices share the network config with C7v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti airCube ISPChristian Mauderer2019-04-082-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer <oss@c-mauderer.de> [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for OCEDO UrsusMarkus Scheck2019-04-082-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm Atheros QCA9558 RAM: 128MB FLASH: 16MB (Macronix MX25L12845EMI-10G) WLAN1: QCA9558 2.4GHz 802.11bgn 3SS WLAN2: QCA9880 5GHz 802.11ac 3SS LED: Power, LAN1, LAN2, 2.4GHz, 5GHz Serial:Next to SPI Flash, Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3) The Serial setting is 115200-8-N-1 INSTALLATION: 1. Serve an OpenWrt ramdisk image named "ursus.bin". Set your IP-address to 192.168.100.8/24. 2. Connect to the serial. Power up the device and interrupt the boot process. 3. Set the correct bootcmd with > setenv bootcmd run bootcmd_1 > saveenv 4. Run > tftpboot 0x81000000 ursus.bin > bootm 0x81000000 5. Wait for OpenWrt to boot up. 6. Transfer OpenWrt sysupdate image and flash via sysupgrade. Signed-off-by: Markus Scheck <markus.scheck1@gmail.com> Tested-by: David Bauer <mail@david-bauer.net> [whitespace fix, renamed LED labels and SoC type fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for NEC Aterm WG1200CRINAGAKI Hiroshi2019-04-063-7/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - SoC : Qualcomm Atheros QCA9563 - RAM : DDR2 128 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9563 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100/1000 Mbps - Switch : QCA8334 - LEDs/Input : 12x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from power connector side - 115200 bps Flash instruction using factory image: 1. Boot WG1200CR normaly 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Known issues: - cannot be controlled LEDs other than Power (Green/Red) - only Power LEDs are connected to SoC GPIO; other LEDs connected to the gpiochip on ath10k chip (QCA9888) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit message formatting]
* ath79: engenius epg5000: add leds migration scriptTomasz Maciej Nowak2019-04-061-0/+16
| | | | | | | | | | | | | | | With transition from ar71xx to ath79 some of devices change their naming of LEDs. When upgrading from ar71xx target images this will require the user to adjust previously working configuration. This commit adds migration script which can be used to rename old names to new ones. With this previously working configuration will be automatically adjusted, wihtout user intervention. This commit adds migration case for EnGenius EPG5000, the wireless LEDs names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to epg5000:blue:wlan2g and epg5000:blue:wlan5g. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add support for TP-Link CPE210 v2Adrian Schmutzler2019-04-022-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 This is based on the support patch for the identical CPE210 v3 by Mario Schroen <m.schroen@web.de>. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for TP-Link CPE210 v3Mario Schroen2019-04-022-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: Qualcomm Atheros QCA9533 (650MHz) * RAM: 64MB * Storage: 8 MB SPI NOR * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Thanks to robimarko for the work inside the ar71xx tree. Thanks to adrianschmutzler for deep discussion and fixes. Signed-off-by: Mario Schroen <m.schroen@web.de> [Split into DTS/DTSI, read-only config partition in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename, light subject touches] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for COMFAST CF-E5/E7Ding Tengfei2019-03-243-10/+25
| | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on Qualcomm/Atheros QCA9531. Short specification: 2x 10/100 Mbps Ethernet, with 24v PoE support 64 MB of RAM (DDR2) 16 MB of FLASH (SPI) 2T2R 2.4 GHz, 802.11b/g/n built-in 1x 3 dBi antennas output power (max): 80 mW (19 dBm) Qucetel EC20 LTE MODULE(1x external detachable antenna) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [commit subject fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add TP-Link TL-WR710N v1Marcin Jurkowski2019-03-242-0/+9
| | | | | | | | | | | | | | | | | | | | | This commit adds support for TP-Link TL-WR710N v1 router. CPU: Atheros AR9331 400MHz RAM: 32MB FLASH: 8MiB PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN WiFi: Atheros AR9331 1x2:1 bgn USB: ChipIdea HDRC USB2.0 LED: SYS BTN: Reset Sysupgrade from `ar71xx` works without glitches. Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0` respectively, what's consistent with `ar71xx` target. Wireless radio path is automatically upgraded from `platform/ar933x_wmac` to `platform/ahb/18100000.wmac`. Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
* ath79: add support for TP-Link TL-WR941N v7 (CN)Chuanhong Guo2019-03-241-2/+4
| | | | | | | | | | | | | | | | | This adds support for the Chinese version of TL-WR941N v7. It uses QCA9558+AR8236 while the international version uses TP9343 instead. Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 4 MB - RAM: 64 MB - Ethernet: Atheros AR8236 with 5 FE ports Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: Add support for Ubiquiti NanoBeam ACTobias Schramm2019-03-223-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ath79: GL.iNet AR300M-nand/nor: correct LAN LEDAndreas Ziegler2019-03-211-1/+1
| | | | | | | | The port labled as "LAN" is eth1. That's different from the -lite variant, where the only existing port eth0 is used as LAN Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
* ath79: align naming of Ubiquiti Nanostation MSven Roederer2019-03-181-1/+1
| | | | | | | | | | | | | Support for the Nanostation M (XW) was added in 40530c8eb with board name "nanostation-m-xw". The current image for the "Nanostation M" uses "nano-m" as the board name. This commit renames it to the full product name as it's used by all other boards. The legacy boardname of the ar71xx target is added via SUPPORTED_DEVICES to ease switching to ath79 target. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [touch-ups on the commit message, removed subject remains] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for jjPlus JA76PF2Tomasz Maciej Nowak2019-03-182-4/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board. Specification SoC: Atheros AR7161 RAM: 64 MB DDR Flash: 16 MB SPI NOR Ethernet: 2x 10/100/1000 Mbps AR8316 LAN (CN11), WAN/PoE (CN6 - close to power barrel connector, 48 V) MiniPCI: 2x LEDS: 4x, which 3 are GPIO controlled Buttons: 2x GPIO controlled Reset (SW1, closer to ethernet ports), WPS (SW2) Serial: 1x (only RX and TX are wired) baud: 115200, parity: none, flow control: none Currently there is one caveat compared to ar71xx target images as the MAC addresses are random on every reboot. To remedy this one needs to store the WAN MAC address in RedBoot configuration. OpenWrt on first boot, after flashing, will read out the address and assign proper ones to both WAN and LAN ports. It is iportant to NOT keep the old configuration when doing sysupgrade from ar71xx. Upgrading from OpenWrt ar71xx image 1. Connect to serial port, 2. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n <openwrt_sysupgrade_image_name> 3. After writing new image OpenWrt will reboot, now interrupt boot process and enter RedBoot (bootloader) command line by pressing Ctrl+C, 4. Enter following commands (replace variable accordingly), set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_adress> (confirm storing the value by inputting y and pressing Enter) reset 5. Now board should restart and boot OpenWrt with proper MAC addresses. Installation 1. Prepare TFTP server with OpenWrt initramfs image, 2. Connect to WAN ethernet port, 3. Connect to serial port, 4. Power on the board and enter RedBoot (bootloader) command line by pressing Ctrl+C, 5. Enter following commands (replace variables accordingly): set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_address> (confirm storing the value by inputting y and pressing Enter) ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress> load -r -b 0x80060000 <openwrt_initramfs_image_name> exec -c "" 6. Now board should boot OpenWrt initramfs image, 7. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade <openwrt_sysupgrade_image_name> 8. Wait few minutes, after the D2 LED will stop blinking, the board is ready for configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: routerstation: prepare to use sysupgrade-tar format imageTomasz Maciej Nowak2019-03-181-4/+21
| | | | | | | | | | | | | | | | | | In PR [1] introducing initial support for Ubiquiti RouterStation boards, Mathias Kresin suggested to replace the combined sysupgrade image with tarball generated by sysupgrade-tar.sh. This would simplify deployment of sysupgrade as the kernel size (needed to update FIS partition) could be simply calculated on the fly instead of reading value from combined image header. Unfortunately this would break sysupgrade compatibility between ar71xx image and ath79 image. Therefore this commit creates migration path to use new sysuprade image, it adds code to accept both of them at this moment. The plan is to keep it until new stable version is released. Then the image recipe should be changed to new format and compatibility code for old image removed. 1. https://github.com/openwrt/openwrt/pull/1237 Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: qca955x: add wmac migration hotplug eventTomasz Maciej Nowak2019-03-181-0/+32
| | | | | | | | | | | When upgrading from ar71xx target images to ath79 based ones, the integrated wireless interface changes its sysfs path. Therefore the previous enabled wireless interface will be disabled, which can cause false complains about it not working. This commit adds hotplug event which migrates to new path and will keep the wrireless interface enabled after upgrade. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Speed up caldata/eeprom handlingAdrian Schmutzler2019-03-132-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Speed comparison @ UBNT AC-Mesh (just manually) results in a time reduction by three orders of magnitude (99.9 %). > time dd if=/dev/mtd6 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096 4096+0 records in 4096+0 records out real 0m 16.84s user 0m 0.07s sys 0m 13.54s > time dd if=/dev/mtd6 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.02s user 0m 0.00s sys 0m 0.02s Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Rosen Penev <rosenp@gmail.com>
* ath79: add suport for EnGenius EPG5000Tomasz Maciej Nowak2019-03-133-12/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band wireless router. Specification SoC: Qualcomm Atheros QCA9558 RAM: 256 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled Buttons: 2x GPIO controlled UART: 4 pin header, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Tools > Firmware, 4. Select OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Alternative installation 1. Prepare TFTP server with OpenWrt sysupgrade image, 2. Connect to one of LAN (yellow) ethernet ports, 3. Connect to UART port (leaving out VCC pin!), 4. Power on router, 5. When asked to enter a number 1 or 3 hit 2, this will select flashing image from TFTP server option, 6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8), then router ip (default is 192.168.99.9) and for last, image name downloaded from TFTP server (default is uImageESR1200_1750), 7. After providing all information U-Boot will start flashing the image, You can observe progress on console, it'll take few minutes and when the Power LED will stop blinking, router is ready for configuration. Additional information If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: aigo3d0a0tdagr useful for creating backup of original firmware. When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep the old configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add GL.iNet AR-300M-LiteJeff Kletsky2019-03-132-0/+8
| | | | | | | | | | | | | | | | | | | | | AR300M-Lite is single-Ethernet variant of the AR300M series Its eth0 would otherwise be assigned to the WAN interface making it unreachable firstboot or failsafe. Installation instructions from OEM (OpenWrt variant): * Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI), * Do not preserve settings * Access rebooted device via Ethernet at OpenWrt default address Add previously missing LED defaults for all three variants; -nand, -nor, -lite to the definitions in 01_leds Non-lite variants thanks to Andreas Ziegler https://patchwork.ozlabs.org/patch/1049396/ Runtime-tested: GL.iNet AR300M-Lite Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: add support for LibreRouter v1Santiago Piccinini2019-03-132-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: QCA9558 RAM: 128M DDR2 Flash: 16MiB SPI-NOR ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through WiFi2: QCA9558 (bgn) 2T2R WiFi5: 2x mPCIE with AR9582 (an) 2T2R BTN: 1x Reset GPIO: multiple GPIO on header, PoE passthrough enable UART: 3.3V 115200 8N1 header on the board WDG: ATTiny13 watchdog JTAG: header on the board USB: 1x connector and 1x header on the board PoE: 10-32V input in ETH port 1, passthrough in port 2 mPCIE: 2x populated with radios (but replaceable) OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin using the web interface or with sysupgrade -n. Flash from bootloader (in case failsafe does not work) 1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART header in the board. 2. Connect an ETH cable and configure static ip addres 192.168.1.10/24 3. Turn on the device and stop the bootloader sending any key through the serial interface. 4. Use a TFTP server to serve <your image>-sysupgrade.bin file. 5. Execute the following commands at the bootloader prompt: ath> tftp 82000000 <your image>-sysupgrade.bin ath> erase 0x9f050000 +$filesize ath> cp.b 0x82000000 0x9f050000 $filesize ath> bootm 0x9f050000 More docs * Bootloader https://github.com/librerouterorg/u-boot * Board details (schematics, gerbers): https://github.com/librerouterorg/board Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>