aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files/etc/hotplug.d
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: add support of D-Link DIR-825 B1Dmitry Tunin2018-08-111-0/+22
| | | | | | Add support for the ar71xx supported D-Link DIR-825 B1 to ath79. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add ath9k calibration data MAC addresses patchingChristian Lamparter2018-08-111-0/+50
| | | | | | | | | | | | | | | | | | This patch copies over the MAC patching helper functions from lantiq's target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom file. Not all vendors bothered to write the correct MAC addresses for the ath9k wifi into the calibration data. And while ath9k does have some special dt-properties to extract the addresses from a fixed position, there are still devices that require userspace to edit or modify the caldata. In my case, the MAC address for the Wi-Fi device is stored in an unsorted key-value based "nvram" database and there's an existing userspace tool to extract the data. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for TP-Link TL-WDR4900 v2Chuanhong Guo2018-08-111-1/+2
| | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 8 MB - RAM: 128 MB - Ethernet: AR8327N with 5 GE ports. - Wireless radio: QCA9558 for 2.4G and AR9580 for 5G. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for OCEDO KoalaDavid Bauer2018-08-091-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Fix led nodes for TL-WR740N v2 and add its clonesChuanhong Guo2018-08-081-1/+8
| | | | | | | | | | | | | | | | This patch did the following things: 1. Separate ath9k-leds out of gpio leds so that all other leds will work before ath9k loded (e.g. during preinit/init stage). 2. Rename wps led to qss since that's how TP-Link mark it. 3. Rename LED prefix to tp-link because that dts is shared by many devices. 4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1. (This will require a forced sysupgrade if you comes from the previous wr740n v2 image.) 5. Remove SUPPORTED_DEVICES. (tl-wr740n-v2 doesn't exist anywhere so it's useless.) 6. Add all WR741ND v1 clones found in ar71xx. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: rename tl-archer-c7 to archer-c7Chuanhong Guo2018-08-061-4/+4
| | | | | | | | This router is called Archer C7 and the tl was used to identify TP-LINK. Since we have added tplink in dts/board name, the tl prefix is useless now. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: remove quotes for boardname in scriptsChuanhong Guo2018-08-062-21/+20
| | | | | | Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: put all devices in alphabetical order in scriptsChuanhong Guo2018-08-061-1/+1
| | | | | | | And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: really fix TP-Link Archer C7 v2 MAC addressMathias Kresin2018-08-041-1/+1
| | | | | | | | | | | | | | | | | | | | Revert 290c54473ead ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address") which obviously aims to have a distinct MAC address per interface. Unfortunally it doesn't match what is used by the stock firmware and we shouldn'z use MAC Adresses not reserverd for/assigned to a particular board. The correct MAC adress increments for this board are: wlan0 (5GHz) : -1 wlan1 (2.4GHz) : 0 eth1 (LAN) : 0 eth0 (WAN) : 1 Fixes: FS#408 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Port PowerCloud Systems CAP324 supportDaniel F. Dickinson2018-07-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The CAP324 was an AP for a NaaS offering that is now defunct. While previously supported in the ar71xx arch, there were some errata (to be fixed shortly). Notable differences from ar71xx support: 1) The method of getting the ath9k firmware for the PCIe 2ghz wifi has changed (due to changes in how the arch handles this), since this device doesn't use the EEPROM except to get the MAC address of the wifi. 2) /etc/config/wireless will need to be regenerated as the path(s) to the wireless device(s) have changed. 3) ath79 OpenWrt firmware no longer supports build an image that allows reverting to stock firmware (as the cloud service no longer exists, the stock firmware is useless), instead using all of the flash for image and overlay (less u-boot/env and art). 4) Initial network config treats the ethernet port as a Lan port with the standard default address (192.168.1.1 unless changed in .config --e.g. via menuconfig) instead of using DHCP (this was the default for the stock firmware, however for openwrt use this is rather confusion and counter-productive as the user has a harder time finding the device on the network. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ath79: add support for OCEDO RaccoonDavid Bauer2018-07-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Raccoon SOC: Atheros AR9344 RAM: 128MB FLASH: 16MiB WLAN1: AR9344 2.4 GHz 802.11bgn 2x2 WLAN2: AR9382 5 GHz 802.11an 2x2 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5 Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. NOTE: The U-Boot won't boot with the serial attached. Boot the device without serial attached and attach it after 3 seconds. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'raccoon-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for UniFi AC-Mesh ProChristoph Krapp2018-07-071-0/+1
| | | | | | | | | The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except USB support. Furthermore for setting parameters like antenna gain it is helpful to know the exact device variant. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: add support for TP-Link RE450 v2Peter Lundkvist2018-07-021-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE450 v2 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers) Flash instruction: Apply factory image in OEM firmware web-gui. U-Boot does not seem to have any recovery functions, so debricking requires connection via UART. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* ath79: add support for Unifi AC MeshAdrian Schmutzler2018-06-281-0/+1
| | | | | | | | | The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for more AR7241 TP-Link boardsDmytro Smyrnov2018-06-281-0/+3
| | | | | | | | | | | Its common AP99(AR7241) platform with following devices: TP-Link TL-WR841N/ND v7 (SoC AR7241 / Wifi AR9287 / without USB) TP-Link TL-MR3220 v1 (SoC AR7241 / Wifi AR9285 / USB support) TP-Link TL-MR3420 v1 (SoC AR7241 / Wifi AR9287 / USB support) Signed-off-by: Dmytro Smyrnov <dioptimizer@hotmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Ubiquiti UniFi AC-ProLucian Cristian2018-06-281-1/+2
| | | | | | | | rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: sync naming of Ubiquiti devicesAdrian Schmutzler2018-06-281-1/+1
| | | | | | | Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer c7 v2Sibren Vasse2018-06-261-1/+5
| | | | Signed-off-by: Sibren Vasse <github@sibrenvasse.nl>
* ath79: add tl-wr2543-v1 supportLucian Cristian2018-06-261-0/+1
| | | | | | to switch between wlan leds we need a userspace implementation Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add support for ON Networks N150RZoltan HERPAI2018-06-261-0/+1
| | | | | | | | | | | | This is a rebranded Netgear WNR612v2, specs are the same. - Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: add Netgear WNR612 v2Zoltan HERPAI2018-06-261-0/+1
| | | | | | | | | | | | | | | Netgear WNR612 v2: - cpu Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 As there is a rebranded WNR612v2 called ON Networks N150R, add a dtsi which includes all device support, and add a separate dts for the device only (with a separate one for the subsequent N150R). Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: add ubiquiti unifi ap ac lite/lrLucian Cristian2018-06-181-0/+3
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add support for Phicomm K2TWeijie Gao2018-06-182-0/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds dts for qca956x and also support for Phicomm K2T The qca965x.dtsi adds nearly all the necessary components. Both ath9k AHB and PCIe worked well. The Phicomm K2T uses MTD partition 'config' to store the mac addresses in JSON format. To extract these fields correctly, a script is introduced: /lib/functions/k2t.sh This script provides a helper function to extract mac addresses, and is used in three places. Hardware spec of Phicomm K2T: CPU: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337 WiFi 5.8GHz: QCA9886 Flash instruction: Apply sysupgrade.bin via serial console: tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ath79: add TP-Link TL-WR740N/ND v2 portAlex Maclean2018-06-011-0/+1
| | | | Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ath79: preliminary support for TP-Link WDR3600 / WDR4300 (AR9344)Johann Neuhauser2018-05-221-0/+4
| | | | | | | | | | | | | | | | working: - leds - buttons - lan / wan - usb (hub port 1 + 2) - wifi 5g - sysupgrade - ... not working: - wifi 2g Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: add AVM FRITZ!WLAN Repeater 300EMathias Kresin2018-05-171-0/+21
| | | | | | No known issues, everything works fine. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add new OF only target for QCA MIPS siliconJohn Crispin2018-05-072-0/+98
This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-21 07:35:23 +0000