aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files/etc/board.d
Commit message (Collapse)AuthorAgeFilesLines
* ath79: split base-files into subtargetsAdrian Schmutzler2019-10-273-840/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | While most of the target's contents are split into subtargets, the base-files are maintained for the target as a whole. However, OpenWrt already implements a mechanism that will use (and even prefer) files in the subtargets' directories. This can be exploited to make several scripts subtarget-specific and thus save some space (especially helpful for the tiny devices). The only script remaining in parent base-files is /etc/hotplug.d/ieee80211/00-wifi-migration, everything else is moved/split. Note that this will increase overall code lines, but reduce code per subtarget. base-files ipk size reduction: master (generic) 49135 B split (generic) 48533 B (- 0.6 kiB) split (tiny) 43337 B (- 5.7 kiB) split (nand) 44423 B (- 4.6 kiB) Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for ZyXEL NBG6716André Valentin2019-10-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Attention: Kernel partition size has been enlarged to 4MB. To switch, you must update to latest ar71xx-nand snapshort and flash the sysupgrade-4M-Kernel.bin: zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f You will end up with a fresh config if you do not inject config into the image. The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but ath79 can only use the first 128MB. Therefore the complete NAND needs to be overwritten. If not, the old UBI may make problems and lead to reboot loop. Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6716> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6716> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6716> ATSE NBG6716 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6716> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6716> ATGU |NBG6716# Signed-off-by: André Valentin <avalentin@marcant.net>
* ath79: add support for Netgear WNR1000 v2Michal Cieslakiewicz2019-10-212-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNR1000v2. Router was previously supported by ar71xx target only. Note: this is a 4_32 device with limited upgrade capabilities. Specification ============= * Description: Netgear WNR1000 v2 * Loader: U-boot * SOC: Atheros AR7240 (340 MHz) * RAM: 32 MiB * Flash: 4 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 3712 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9285) * USB: no * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_tiny=y CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr1000-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNR2000 v3Michal Cieslakiewicz2019-10-212-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNR2000v3. Router was previously supported by ar71xx target only. Note: this is a 4_32 device with limited upgrade capabilities. Specification ============= * Description: Netgear WNR2000 v3 * Loader: U-boot * SOC: Atheros AR7241 (360 MHz) * RAM: 32 MiB * Flash: 4 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 3712 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9287) * USB: no * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_tiny=y CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Sitecom WLR-7100Tomasz Maciej Nowak2019-10-211-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless router. Specification SoC: Atheros AR1022 RAM: 64 MB DDR2 Flash: 8 MB SPI NOR WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R QCA9882 integrated (connected to PCIe lane) Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled, 5x switch Buttons: 2x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Toolbox > Firmware, 4. Browse for OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues 5GHz LED doesn't work Additional information When TX line on UART is connected, and board is switched on from power off state, the DDR memory training may fail. If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), which may or may not work with introduced images. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add support for UniFi AC-LRAndreas Ziegler2019-10-151-0/+1
| | | | | | | | | | | | | | The Unifi AC-LR has identical hardware to the Unifi AC-Lite. The antenna setup is different according to the vendor, which explains the thicker enclosure. Therefore, it is helpful to know the exact device variant, instead of having "Ubiquiti UniFi-AC-LITE/LR". Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [fix legacy name in commit message; add old boardname to SUPPORTED_DEVICES] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for COMFAST CF-E313ACRoger Pueyo Centelles2019-10-131-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E313AC, an outdoor wireless CPE with two Ethernet ports and a 802.11ac radio. Specifications: - QCA9531 SoC - 650/400/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps WAN Ethernet, 48V PoE-in - 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out - 1x manual pass-through PoE switch - 64 MB RAM (DDR2) - 16 MB FLASH - QCA9886 2T2R 5 GHz 802.11ac, 23 dBm - 12 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. Alternatively, the U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The device's LEDs will blink several times and the recovery page will be at http://192.168.1.1; use it to upload the sysupgrade image. Note: Four MAC addresses are stored in the "art" partition (read-only): - 0x0000: 40:A5:EF:AA:AA:A0 - 0x0006: 40:A5:EF:AA:AA:A2 - 0x1002: 40:A5:EF:AA:AA:A1 - 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data) The stock firmware assigns MAC addresses to physical and virtual interfaces in a very particular way: - eth0 corresponds to the physical Ethernet port labeled as WAN - eth1 corresponds to the physical Ethernet port labeled as LAN - eth0 belongs to the bridge interface br-wan - eth1 belongs to the bridge interface br-lan - eth0 is assigned the MAC from 0x0 (*:A0) - eth1 is assigned the MAC from 0x1002 (*:A1) - br-wan is forced to use the MAC from 0x1002 (*:A1) - br-lan is forced to use the MAC from 0x0 (*:A0) - radio0 uses the calibration data from 0x5000 (which contains a valid MAC address, *:A3). However, it is overwritten by the one at 0x6 (*:A2) This commit preserves the LAN/WAN roles of the physical Ethernet ports (as labeled on the router) and the MAC addresses they expose by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position of the eth0/eth1 compared to the stock firmware: - eth0 corresponds to the physical Ethernet port labeled as LAN - eth1 corresponds to the physical Ethernet port labeled as WAN - eth0 belongs to the bridge interface br-lan - eth1 is the interface at @wan - eth0 is assigned the MAC from 0x0 (*:A0) - eth1 is assigned the MAC from 0x1002 (*:A1) - br-lan inherits the MAC from eth0 (*:A0) - @wan inherits the MAC from eth1 (*:A1) - radio0's MAC is overwritten to the one at 0x6 This way, eth0/eth1's positions differ from the stock firmware, but the weird MAC ressignations in br-lan/br-wan are avoided while the external behaviour of the router is maintained. Additionally, WAN port is connected to the PHY gmac, allowing to monitor the link status (e.g., to restart DHCP negotiation when plugging a cable). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: Correct glinet, gl-ar300m-lite in 02_networkJeff Kletsky2019-09-291-1/+1
| | | | | | | | | | | | | | Previously, the board name for the GL-AR300M-Lite was incorrect in 02_network, resulting in an unintended, fall-through condition when initializing the network configuration. While builds prior to commit 8dde11d521 (merged June 5, 2019) ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi functioned properly, the error was noted in resolving first-boot connectivity issues related to the single-phy nature of the device and the "swap" of eth0 and eth1 related to that commit. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: remove redundant ucidef_set_interfaces_* calls in 02_networkAdrian Schmutzler2019-09-251-2/+1
| | | | | | | | | | If already included in ucidef_add_switch, you do not have to additionally set the interface mode in ucidef_set_interfaces_* functions. This patch removes/adjusts such redundant cases. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support of Netgear WNDR3800CHDmitry Tunin2019-09-211-1/+2
| | | | | | | | Add support for the ar71xx supported Netgear WNDR3800CH to ath79. The device is identical to WNDR3800 except NETGEAR_BOARD_ID. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: provide label MAC addressAdrian Schmutzler2019-09-191-10/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ath79. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - alfa-network,ap121f - avm,fritz300e - ubnt-xm devices For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - adtran,bsap1800-v2 - adtran,bsap1840 - dlink,dir-842-c1/-c2/-c3 - engenius,ecb1750 - iodata,etg3-r - iodata,wn-ac1167dgr - iodata,wn-ac1600dgr - iodata,wn-ac1600dgr2 - iodata,wn-ag300dgr - nec,wg800hp - nec,wg1200cr - trendnet,tew-823dru Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C59v2Keith Maika2019-09-162-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath79 support for Archer C59v2, previously supported by ar71xx. TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* ath79: eg200: enable status led usageKarl Palsson2019-09-151-1/+0
| | | | | | | | | This enables using the "eTactica" LED during boot, to indicate failsafe, and during upgrade, while still leaving the LED alone for normal operation. This brings the device more in line with how other devices work, and makes the failsafe functionality easier to use and understand. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: add support for TP-Link WDR3500 v1Adrian Schmutzler2019-09-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: AR9344 CPU: 560 MHz Flash: 8 MiB RAM: 128 MiB WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9300 5GHz 802.11an Ethernet: AR934X built-in switch, WAN on separate physical interface USB: 1x 2.0 Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wdr3500v1_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [removed stray newline] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for gl-ar750Luochongjun2019-08-241-0/+5
| | | | | | | | | | | | | | | | | | | | This patch supports gl-ar750, which was previously supported by ar71xx. Specification: - SOC: QCA9531 (650MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 10/100: 2xLAN + 10/100: 1xWAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Switch: 1x switch - Button: 1x reset button - LED: 3x LEDS (white) Flash instruction: Support for sysupgrade directive upgrades, as well as luci upgrades. Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
* ath79: migrate TP-Link TL-MR3420v2 to ath79Lim Guo Wei2019-08-172-18/+20
| | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: ar9341 - RAM: 32M - Flash: 4M - Ethernet: 5x FE ports - WiFi: ar9341-wmac Flash instruction: Upload generated factory firmware on vendor's web interface. This changes the key assignment compared to ar71xx support of this device, since of the two keys on the device one is used as combined Reset/WPS and the second one as WiFi on/off button. Despite, the reset button required GPIO_ACTIVE_HIGH to work correctly. Signed-off-by: Lim Guo Wei <limguowei@gmail.com> [redo commit message] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for PISEN TS-D084xixiao zheng2019-08-171-0/+1
| | | | | | | | | | | | | | | | | | | | | PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz (AR9331) - 1x USB 2.0 Flash instruction: Upload generated factory image through web interface. Signed-off-by: xixiao zheng <xixiaozheng64@gmail.com> [wrap commit message, add flash instruction] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: adtran,bsap1840/bsap1800-v2: move bootcount out of 02_networkChuanhong Guo2019-08-171-1/+0
| | | | | | | | | These device supports were introduced before /etc/init.d/bootcount and they had a bootcount reset done in /etc/board.d/02_network. Move it into /etc/init.d/bootcount instead. Suggested-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-141-14/+14
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix identation errors in 01_ledsDavid Bauer2019-08-091-7/+7
| | | | | | Fix the identation of 01_leds to keep the style of the file consistent. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix whitespace errors from adding D-Link DIR-842 C3Adrian Schmutzler2019-08-091-2/+2
| | | | | | | | | We completely overlooked whitespace errors when reviewing 796ad2f7ef6f ("ath79: add support for D-Link DIR-842 C3"). Fix them and and also fix Makefile indent for C1/C2. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Comfast WR650AC v1/v2Joan Moreau2019-08-091-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a dual band 11a/11n router with 1x wan and 4x gig lan ports. There are two versions of this router which can be identified through the factory web interface, v1 has 128mb ram and a uboot size of 128k, v2 has 256mb ram and a uboot size of 256k, the remaining hardware and PCB markings are the same. Short specification: SoC: Qualcomm Atheros QCA9558 - 720 MHz Switch: Atheros AR8327 Second radio : Qualcomm Atheros QCA9880 802.11ac 4 LAN/1 WAN 1000Mps Ethernet 256 MB of RAM (DDR2) 16 MB of FLASH 3x2.4 GHz, 3x5GHz antennas Steps to install : Option A : Use vendor UI Option B (if A is not working) : (a) Download 'backup' from vendor UI and rename it backup.tar.gz (b) Open the archive, and update the root password in /etc/shadow by '$1$9wX3HGfB$X5Sb3kqzzBLdKRUR2kfFd0' (c) 'Restore' from the archive using the vendor UI. Root password is now 'aaa' (d) Scp the firwmware to the device: $ scp <openwrt-sysupgrade>.bin root@192.168.1.1:/ (d) ssh to the device and flash the firmware: $ cd / $ mtd -e firmware -r write <openwrt-sysupgrade>.bin firmware Signed-off-by: Gareth Parker <gareth41@orcon.net.nz> Signed-off-by: Ding Tengfei <dtf@comfast.cn> Signed-off-by: Joan Moreau <jom@grosjo.net> [reformatted commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Comfast E314N-v2Joan Moreau2019-08-092-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Taken code from https://patchwork.ozlabs.org/patch/884850/ that was never pushed by the author, and adapted to ath79. The Comfast E314N-V2 is a 2.4 GHz 2x2 radio with a built-in directional antenna and a second Ethernet port - very similar to the Ubiquiti NanoStation M2. The Ethernet port features a pass-through PoE capability, enabled or disabled with a slide switch. Specifications : - System-On-Chip: Qualcomm/Atheros QCA9531 - CPU/Speed: 650 MHz - Flash size: 8 MiB - RAM: 64 MiB - 2 Ethernet 1Gbp - 1 reset button - 1 switch to choose PoE from LAN or Wan. 48Vdc - Wifi 2.4 Ghz (b/g/n) - UART inside the box (3.3V, pins marked on the PCB) Firmware can be flashed on these units by the following method: 1.) Apply power to the unit 2.) Immediately AFTER applying power, hold down the reset button 3.) The WAN, LAN, and wireless lights will flash - wait three seconds (three flashes) and then release the button. 4.) After a second, the lights will flutter quickly and the unit will be visible at 192.168.1.1. A web page will be available to enable quick and simple uploading and flashing of firmware. During the boot process, these units also look for a tftp server at 192.168.1.10. If one is present, the firmware can be uploaded as a file called firmware-auto.bin Signed-off-by: Joan Moreau <jom@grosjo.net> [wrapped commit message - fix commit title capitalization] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for PISEN WMB001NChuanhong Guo2019-08-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: AR9341 - RAM: 64M - Flash: 16M - Ethernet: 1 * FE port - WiFi: ar934x-wmac - Sound: WM8918 DAC 1 * 3.5mm headphone jack 2 * RCA connectors for speakers 1 * SPDIF out - USB: 1 * USB2.0 port Flash instruction: Upload generated factory image via vendor's web interface. Notes: A. Audio stuff: 1. Since AR934x, all pins for peripheral blocks can be mapped to any available GPIOs. We currently don't have a PCM/I2S driver for AR934x so pinmux for i2s and SPDIF are bound to i2c gpio node. This should be moved into I2S node when a PCM/I2S driver is available. 2. The i2c-gpio node is for WM8918. DT binding for it can't be added currently due to a missing clock from I2S PLL. B. Factory image: Image contains a image header and a tar.gz archive. 1. Header: A 288 byte header that has nothing to do with appended tarball. Format: 0x0-0x7 and 0x18-0x1F: magic values 0x20: Model number string 0xFC: Action string. It's either "update" or "backup" 0x11C: A 1 byte checksum. It's XOR result of 0x8-0x11B Firmware doesn't care about the rest of the header as long as checksum result is correct. The same header is used for backup and update routines so the magic values and model number can be obtained by generating a backup bin and grab values from it. 2. Tarball: It contains two files named uImage and rootfs, which will be flashed into corresponding mtd partition. Writing a special utility that can only output a fixed binary blob is overkill so factory image header is placed under image/bin instead. C. LED The wifi led has "Wi-Fi" marked on the case but vendor's firmware used it as system status indicator. I did the same in this device support patch. D. Firmware Factory u-boot is built without 'savenv' support so it's impossible to change kernel offset. A 2MB kernel partition won't be enough in the future. OKLI loader is used here to migrate this problem: 1. add OKLI image magic support into uImage parser. 2. build an OKLI loader, compress it with lzma and add a normal uImage header. 3. flash the loader to where the original kernel supposed to be. 4. create a uImage firmware using OKLI loader. 5. flash the created firmware to where rootfs supposed to be. By doing so, u-boot will start OKLI loader, which will then load the actual kernel at 0x20000. The kernel partition is 2MB, which is too much for our loader. To save this space, "mtd-concat" is used here: 1. create a 64K (1 erase block) partition for OKLI loader and create another partition with the left space. 2. concatenate rootfs and this partition into a virtual flash. 3. use the virtual flash for firmware partition. Currently OKLI loader is flashed with factory image only. sysupgrade won't replace it. Since it only has one function and it works for several years, its unlikely to have some bugs that requires a replacement. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for D-Link DIR-842 C3Perry Melange2019-08-072-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C3: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: circuit onboard, but components are not soldered Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
* ath79: add support for TP-Link CPE220 v2Adrian Schmutzler2019-08-073-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | This seems to be identical to CPE210 v1 despite having removable antennas. Specifications: * SoC: Qualcomm Atheros AR9344 (560 MHz) * RAM: 64MB * Storage: 8 MB * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE510 v1Adrian Schmutzler2019-08-073-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with two Ethernet ports based on Atheros AR9334 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 2T2R 5 GHz - 13 dBi built-in antenna - Power, LAN0, LAN1 green LEDs - 4x green RSSI LEDs Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Based on the work of Paul Wassi <p.wassi@gmx.at> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE210 v1Adrian Schmutzler2019-08-073-0/+13
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: Qualcomm Atheros AR9344 (560 MHz) * RAM: 64MB * Storage: 8 MB * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP9343-based TP-Link TL-WR94x devicesAdrian Schmutzler2019-08-052-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for several TP-Link devices based on TP9343 ("a QCA9561 without PCIe and USB"): - TL-WR940N v3 - TL-WR940N v4 - TL-WR941ND v6 The devices are only different concerning LEDs and MAC address assignment. All TL-WR940 are with non-detachable antennas (N), all TL-WR941 devices are with detachable antennas (ND). Specification: - 750 MHz CPU - 32 MB of RAM - 4 MB of FLASH - 2.4 GHz WiFi - 4x 10/100 Mbps Ethernet Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to * (see below) 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. * TFTP image names: 940 v3: wr941ndv6_tp_recovery.bin 940 v4: wr940nv4_tp_recovery.bin 941 v6: wr941ndv6_tp_recovery.bin Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for D-Link DIR-842 C1Jackson Lim2019-08-052-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C1: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: circuit onboard, but components are not soldered Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim <jackcolentern@gmail.com> [fix whitespace issues] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WR841N/ND v12Adrian Schmutzler2019-08-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC ID, same TFTP image name...). Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wr841nv11_tp_recovery.bin (it's really v11, not v12) 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR841N/ND v10Adrian Schmutzler2019-08-052-0/+2
| | | | | | | | | | | | | | | | | | | | | | | The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor changes, it contains a newer revision of the QCA9533 SoC and the CPU clock is significantly higher. Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wr841nv10_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for ALFA Network AP121FRoger Pueyo Centelles2019-07-312-0/+4
| | | | | | | | | | | | | This commit ports support for the ALFA Network AP121F, a pocket-size router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the ath79 target (it was already supported in ar71xx; see commit 0c6165d2 for more details). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env partition writable] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: fix indent in 01_ledsAdrian Schmutzler2019-07-241-2/+2
| | | | | | | | | Change capitalization from spaces to tabs in order to match the style of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [fix capitalization in commit title, add short description] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DIR-842 C2Jackson Lim2019-07-242-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C2: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: 2.0 Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim <jackcolentern@gmail.com> [Reword reset-hog comment, fix formatting] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Add support for TP-Link Archer C60 v2Adrian Schmutzler2019-07-182-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60 v2 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed IP address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery Flash instruction (under U-Boot, using UART): tftp 0x81000000 ...-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C60 v1Adrian Schmutzler2019-07-182-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 ...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE510-v2/v3Andrew Cameron2019-07-182-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, and 4 green LEDs - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in) - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna - Adjustable transmission power from 0 to 23dBm/200mw Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Trendnet TEW-823DRUPramod Pancha2019-07-182-1/+9
| | | | | | | | | | | | | | | | | | | | | Trendnet TEW-823DRU is a dual-band AC1750 router. The router is based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: 720 MHz CPU 256 MB of RAM 16 MB of FLASH 3T3R 2.4 GHz 3T3R 5 GHz 5x 10/100/1000 Mbps Ethernet Firmware can be flashed from the web interface. Tested on 3 routers with no issues. Signed-off-by: Pramod Pancha <pancha@vill.com> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link RE355 v1 and RE450 v1Christoph Krapp2019-07-172-0/+4
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: Qualcomm Atheros QCA9558 RAM: 64/128MiB Flash: 8MiB SPI-NOR Wifi: - 2.4GHz: 3T3R (QCA9558) - 5GHz: 3T3R (QCA9880) LAN: 1x 10/100/1000 Mbps UART: - TP1: Tx - TP2: Rx - TP3: Gnd - TP4: 3v3 Flash instructions: Flash factory image through stock firmware WEB UI. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: add support for Bluesocket BSAP1880 boardDaniel Gimpelevich2019-07-172-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Qihoo C301Chuanhong Guo2019-07-162-0/+12
| | | | | | | | | | | | | | | | Specifications: - SoC: AR9344 - RAM: 128MB - Flash: 2 * 16MB (MX25L12845) - Ethernet: 2 * FE LAN & 1 * FE WAN - WiFi: 2.4G: AR9344 5G: QCA9882 Flash instruction: 1. Hold reset and power up the router 2. Set your IP to 192.168.1.x 3. Open 192.168.1.1 and upload the generated *factory* firmware Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for devolo WiFi pro 1750xDavid Bauer2019-07-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED Power (non-controllable) 1x LED Status (internal) 1x LED LAN (controlled by PHY) 1x LED WLAN BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to external-LED header. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Use -v1 suffix for TP-Link WDR3600/4300Adrian Schmutzler2019-07-031-2/+2
| | | | | | | | | | | | | | | In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have been used while most other TP-Link devices include the revision. Although there actually is only one major revision of these devices, they bear the revision on their bottom (v1.x). TP-Link also refers to the devices as V1 on its web page. This patch thus adds -v1 to both so it is more consistent with other devices and with what you would expect from reading the on-device sticker and the support pages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE610-v1Andrew Cameron2019-06-242-0/+4
| | | | | | | | | | | | | | | | | | | | | TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, WLAN5G green LEDs - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: Add support for TP-Link Archer C25 v1Adrian Schmutzler2019-06-103-9/+15
| | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip, but not all of them as e.g. for the C59. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Reorder some TP-Link Archer devices in 01_ledsAdrian Schmutzler2019-06-101-8/+8
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consistently label art partition with lower caseAdrian Schmutzler2019-06-101-1/+1
| | | | | | | | This patch harmonizes the label and alias for art partitions across ath79. Since lower case seems to be more frequent, use that consistently. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consistently label info partitionAdrian Schmutzler2019-06-101-9/+3
| | | | | | | | | | | | | | | | The info/product-info partition, which frequently contains MAC adresses, is typically assigned the 'info' alias in DTS, but then labelled with 'info', 'product-info' or 'config'. This leads to different aliases if used for setting MAC adresses in DTS compared to when using e.g. mtd_get_mac_binary. Occationally, also multiple switch-case entries are used just because of different labelling. This patch relabels those partitions in ath79 to consistently use 'info'. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for 8devices Carambola2 development boardRytis Zigmantavičius2019-06-051-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Atheros AR9331 (400 MHz) - 64 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 1T1R 2.4 Wlan (AR9331) - 2x 10/100 Mbps Ethernet - 3x LEDs, 1x gpio button - 1x USB 2.0, 5V - UART over usb, 115200n8 Upgrading from ar71xx target: - Put image into board: scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \ root@192.168.1.1/tmp/ - Run sysupgrade sysupgrade /tmp/sysupgrade.bin Upgrading from u-boot: - Set up tftp server with sysupgrade.bin image - Go to u-boot (reboot and press ESC when prompted) - Set TFTP server IP setenv serverip 192.168.1.254 - Set device ip from same subnet setenv ipaddr 192.168.1.1 - Copy new firmware to board tftpboot 0x81000000 sysupgrade.bin - erase flash erase 0x9f050000 +${filesize} - flash firmware cp.b 0x81000000 0x9f050000 ${filesize} - Reset board reset Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com> [wrapped long line in commit description, whitespace and art address fix in DTS, keep default lan/wan setup, removed -n in sysupgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 09:21:32 +0000