aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: Fix mikrotik NAND compile problemHauke Mehrtens2020-07-071-1/+1
| | | | | | | | | | This Fixes the folowing compile error: drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove': drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function) nand_release(&rbni->chip); Fixes: ce958dd88a7e ("kernel: Update kernel 4.14 to version 4.14.187") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: Fix mikrotik NAND compile problemHauke Mehrtens2020-07-061-1/+1
| | | | | | | There is one closing bracket too much. Fixes: ce958dd88a7e ("kernel: Update kernel 4.14 to version 4.14.187") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Update kernel 4.14 to version 4.14.187Hauke Mehrtens2020-07-045-9/+9
| | | | | | | | | | | | Fixes: - CVE-2020-10757 The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was backported which needed some adaptations to other code. Build tested: ramips Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: correct button type for TL-MR3020 mode sliderDavid Bauer2020-05-311-2/+2
| | | | | | | | | | | | | | The TP-Link TL-MR3020 has a three-state mode slider which was previously integrated as a button (EV_KEY). This led to spurious activations of failsafe mode. Set the type for the button to switch (EV_SW), to avoid unintended activations of failsafe mode. Related: commit 27f3f493de06 ("gpio-button-hotplug: unify polled and interrupt code") Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix reset key for TP-Link TL-WR802N V1/V2Lech Perczak2020-05-311-2/+2
| | | | | | | | | | | | | | | | | | During porting support for this router to ath79 target it was discovered that GPIO mapping was incorrect (GPIO11 active high). Correct mapping for both V1 and V2 is GPIO12 active low. Default configuration from GPL source for V2 explicitly states this, and this was confirmed experimentally on ath79 by looking on /sys/kernel/debug/gpio. Correctness of this was also validated for V1 by cross-flashing vendor firmware for V1 on V2 hardware, in which reset button also worked. Fix it. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [slightly adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix splitting firmware partition for TL-WR902AC v1Adrian Schmutzler2020-05-301-0/+2
| | | | | | | | | | | | The -O option for the tplink-v1-header was missing for the TP-Link TL-WR902AC v1, while safeloader and MTDPARTS where set up with a single firmware partition. This led to bootloops after using sysupgrade. Fixes: FS#3118 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* packages/boot: remove rbcfgThibaut VARÈNE2020-05-281-1/+1
| | | | | | | The new sysfs soft_config driver makes buggy rbcfg obsolete and entirely replaces it. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: mikrotik: mach-rbspi.c remove wlan idThibaut VARÈNE2020-05-121-7/+7
| | | | | | | Following on the previous commit, this patch removes useless id argument from rbspi_wlan_init(). Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: mikrotik: bypass id check in __rb_get_wlan_data()Thibaut VARÈNE2020-05-121-7/+3
| | | | | | | | | | | | | | | | | | | The id parameter in __rb_get_wlan_data() was incorrectly used on the assumption that id "0" would always be tied to ath9k with RLE encoding and positive id (in fact, only id "1" was valid) would always be tied to ("external") ath10k with LZO encoding. Newer hardware revisions of supported devices prove this assumption to be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO compressed, so disable this check to allow newer hardware to correctly decode caldata for ath9k. Since ath10k caldata is no longer pulled from this implementation, this commit also disables the publication in sysfs to avoid wasting memory. Note: this patch assumes that ath9k caldata is never stored with the new "LZOR" encoding scheme found on some ath10k devices. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* kernel: bump 4.14 to 4.14.180Koen Vandeputte2020-05-122-3/+3
| | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2020-12114 - CVE-2020-11669 Compile-tested on: pistachio Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx/mikrotik: ath10k: use new sysfs driverThibaut VARÈNE2020-05-081-2/+2
| | | | | | Fetch ath10k calibration data from new mikrotik sysfs driver Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx/mikrotik: enable mikrotik platform driverThibaut VARÈNE2020-05-081-0/+2
| | | | Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* kernel: bump 4.14 to 4.14.176Koen Vandeputte2020-04-161-1/+1
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch - 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch - 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch Fixes: - CVE-2020-8648 (potentially) - CVE-2020-8647 - CVE-2020-8649 Compile-tested on: cns3xxx, octeontx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: Fix gigabit switch support for Mikrotik RB951G-2HnDBaptiste Jonglez2020-03-281-0/+2
| | | | | | | | | | | | | | | | | | | | Without this patch, when using rev 3 of the Atheros AR9344 SoC, the gigabit switch (AR8327) does not work or works very erratically. This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a different PLL value, according to the feedback from several users (including myself) as shown here: https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports Performance is acceptable: testing L3 forwarding without NAT yields a performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64 bytes payload). Both tests show that 100% of CPU time is spent on softirq. A similar fix for a different device (RB2011) was added in e457d22261 ("Make GBit switch work on RB2011"). Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* ar71xx: use status led for GL.iNet GL-AR750SJan Alexander2020-03-261-0/+1
| | | | | | | | | | | | Use power led for device status. The status led behavior has already been fixed in af28d8a539fe ("ath79: add support for GL.iNet GL-AR750S") when porting the device to ath79. This fixes it for ar71xx as well. Signed-off-by: Jan Alexander <jan@nalx.net> [minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: remove hard-coded folder name from Mikrotik RB upgradeAdrian Schmutzler2020-03-171-1/+6
| | | | | | | | | | | | | | So far, specifying "BOARD_NAME := routerboard" is required by the upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard" is hardcoded in platform_do_upgrade_mikrotik_rb(). This patch replaces the latter with a grep for the name like it is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh. This should enable upgrades from ar71xx to ath79 without setting BOARD_NAME for the latter. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: image: move IMAGE_SIZE to image.mkSungbo Eo2020-03-111-1/+1
| | | | | | | | | | IMAGE_SIZE is widely used in many targets. Declare it in the default template to clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally from the previously defined device. While at it, remove duplicate KERNEL_SIZE declaration. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ar71xx: fix port order on TP-Link Archer C60 v1/v2Adrian Schmutzler2020-03-111-6/+2
| | | | | | | | | The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are actually inverted compared to the ports of the internal switch. Add this information to 02_network. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: remove wrong MAC address adjustment for Archer C60 v2Adrian Schmutzler2020-03-111-2/+1
| | | | | | | | | | | The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac is broken since a "mac" partition is not set up for this device on ar71xx. Instead, the MAC address is already patched correctly in 11-ath10k-caldata. Remove the useless adjustment. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2Adrian Schmutzler2020-03-112-5/+5
| | | | | | | | | | | | | | | | | | | The MAC addresses for lan/wan are swapped compared to the vendor firmware. This adjusts to vendor configuration, which is: lan *:7b label wan *:7c label+1 2.4g *:7b label 5g *:7a label-1 Only one address is stored in <&mac 0x8>, corresponding to the label. This has been checked on revisions v1, v2 and v3. Since ar71xx calculates the ath10k MAC address based on the ethernet addresses, the number there is adjusted, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx/ath79: ew-dorin, fix the trigger level for WPS buttonCatrinel Catrinescu2020-03-111-1/+1
| | | | | | | | | Because the WPS button had the wrong trigger level, the failsafe mode was triggered quite often, after this commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=27f3f493de Signed-off-by: Catrinel Catrinescu <cc@80211.de>
* ar71xx: add missing LED migration for Archer C7David Bauer2020-03-011-0/+3
| | | | | | | | | | | | When changing the LED names for the Archer C7 to represent the correct color, a migration for existing UCI entries was not created. Add a migration to keep existing LED configurations working. Fixes commit c79c001b593b ("ar71xx: Archer C7 v1 LED names and RFKILL fixes") Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: correct AVM FRITZ Repeater 450E WPS button flagDavid Bauer2020-03-011-1/+1
| | | | | | | | | The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low. Correct the active low flag to avoid unintenional activation of failsafe mode on boot. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.171Koen Vandeputte2020-02-244-4/+4
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2013-1798 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.167Koen Vandeputte2020-01-243-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: change u-boot-env to read-write for gl-ar150/-domino/mifiKimmo Vuorinen2020-01-231-3/+3
| | | | | | | | | Change u-boot-env partitions to be mounted as read-write for gl-ar150, gl-domino and gl-mifi so uboot-envtools support is possible. Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: use dynamic partitioning for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-221-1/+1
| | | | | | | This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and will allow to use this for ath79 as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: ubnt-rocket-m-ti: fix RSSI LED definitionsLech Perczak2020-01-212-6/+8
| | | | | | | | | | | | | | | | When mapping for RSSI LEDs was defined for interface wlan0 on Ubiquiti Rocket M Titanium, it missed connection to actual interface. Therefore create the mapping to interface, so RSSI LEDs work without additional configuration, after starting rssileds service. While at that, split RSSI into ~equal intervals for 6 LEDs, and remove coefficients needed for PWM LEDs, as this board does not support PWM LEDs. Finally, for complete support, enable 'rssileds' package in per-device rootfs, so the indicator works out of box. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* kernel: bump 4.14 to 4.14.164Koen Vandeputte2020-01-202-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx/mikrotik: use ath10k-ct-smallbuffers for 64 MiB devicesThomas Nixon2020-01-151-1/+1
| | | | | | | | | | This image is only needed on one device (wAP AC); since this target is going to be removed anyway it doesn't make sense to add an extra "low RAM" image. Fixes OOM issues on RouterBoard wAP AC. Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* ar71xx: Remove mtd cfi_cmdset_0002 status check patchTokunori Ikegami2020-01-051-62/+0
| | | | | | | | | | | | | Currently the patch only changes break to use goto statement instead. But not necessary acutually since the ret value checked after the for loop. So it is okay for the break case before changed by the patch also. This patch only reverts the following commit partially. https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e77619eaa7 Note: The changes are mainly applied into the linux kernel upstream. Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.162Hauke Mehrtens2020-01-051-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ramips Runtime-tested on: ramips Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.159Koen Vandeputte2019-12-241-1/+1
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 302-0002-dmaengine-dw-implement-per-channel-protection-contro.patch Fixes: - CVE-2019-19332 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix MAC address setup for TL-WDR4300 boardSungbo Eo2019-12-212-1/+5
| | | | | | | | | | | | | | | | | The current ethernet MAC address setup of TL-WDR4300 board is different from the setup of stock firmware: OpenWrt: lan = label_mac -2, wan = label_mac -2 stock: lan = label_mac, wan = label_mac +1 This patch applies to all devices using TL-WDR4300 board: TL-WDR3600 v1 TL-WDR4300 v1 TL-WDR4300 v1 (IL) TL-WDR4310 v1 Mercury MW4530R v1 Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ar71xx: indicate upgrade using system LEDDavid Bauer2019-12-161-0/+3
| | | | | | | | | This enables the system LED to indicate a running firmware upgrade. This pattern is used on most platforms provided by the generic base-files package. ar71xx uses it's own implementation for the system-LED, where the upgrade case is not yet implemented. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.158Koen Vandeputte2019-12-101-1/+1
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 400-mtd-add-rootfs-split-support.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ubnt-(xm,xw): add rssileds packageLech Perczak2019-11-211-2/+8
| | | | | | | | | | | | | | | | | | In order to make RSSI indicator on the device work out of box, include "rssileds" package in per-device rootfs image by default for Ubiquiti XM and XW devices, namely: - Bullet M (XM/XW) - Rocket M (XM/XW) - Nanostation M (XM/XW) - Nanostation Loco-M (XW) This moves the package addition to the individual devices in order to prevent accidental inclusions of the package when not looking at the parent node carefully enough. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [add bullet-m-xw, remove rocket-m-ti, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix buttons for TP-Link TL-WDR4900 v2Adrian Schmutzler2019-11-191-2/+13
| | | | | | | TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so don't set up an RFKILL for this device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix LED setup for TL-WDR4900 v2Adrian Schmutzler2019-11-191-2/+36
| | | | | | | | | | | | | | | | | In ar71xx there is only one combined mach file for Archer C5/C7 and TL-WDR4900 v2. This one uses the same LED struct for all devices, defining "green" LEDs for them. However, WDR4900 uses blue front LEDs, while only C5/C7 uses green ones. Despite, in base-files WDR4900 is actually set up with "blue" for the mentioned LEDs. Thus, this patch creates a separate LED struct for WDR4900, so the LEDs can be set up correctly. Despite, the wlan5g LED is removed as it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7). Note: While front LEDs are blue, USB LEDs (on the back) are green, so colors are mixed intentionally for the WDR4900 v2. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix MAC address setup for TL-WDR4900 v2Adrian Schmutzler2019-11-171-3/+6
| | | | | | | | | | | | The MAC address setup of the TL-WDR4900 v2 is different from the C5/C7. This aligns ar71xx with the setup in ath79: wlan0 (5GHz) : -2 wlan1 (2.4GHz) : -1 eth1 (LAN) : 0 eth0 (WAN) : 1 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2Adrian Schmutzler2019-11-132-3/+2
| | | | | | | | | | | | | | | | | | | As discussed in 1d18a14a90c7 ("ath79: really fix TP-Link Archer C7 v2 MAC address"), stock firmware MAC address assignment is actually as follows: wlan0 (5GHz) : -1 wlan1 (2.4GHz) : 0 eth1 (LAN) : 0 eth0 (WAN) : 1 This has never been fixed for ar71xx, so let's do it now. Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned to basemac-1 before ... Fixes: FS#408 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix tl-wdr3320-v2 upgrade南浦月2019-11-081-1/+1
| | | | | | | | | Fix the error that tl-wdr3320-v2 can't upgrade firmware via web interface by using magic_ver="0200" for this device. Signed-off-by: 南浦月 <nanpuyue@gmail.com> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix bug in NBG6716 kernelpacking, add firmware partitionAndré Valentin2019-10-271-2/+3
| | | | | | | -Fix the kernel image generation (more robust) -Add a firmware partition table allowing easy upgrade to ath79 Signed-off-by: André Valentin <avalentin@marcant.net>
* ar71xx: add model detection for UniFi AC-LRAndreas Ziegler2019-10-232-0/+9
| | | | | | | | | | | | | | This commit adds correct model detection for UniFi AC-LR. Previously, said device was incorrectly detected as UniFi-AC-LITE/MESH. The Information about the device is stored at 0xC in the EEPROM partition. It corresponds to the sysid in /etc/board.info of the Ubiquiti stock firmware. Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [adjust naming style of target to existing ones] Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: improve support for TP-Link CPE510 v2Adrian Schmutzler2019-10-217-21/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") where the support for this device wasn't optimal. Device support for the CPE510v2 so far has been a hack to enable flashing with CPE510v1 images. Those even have different hardware (e.g. additional ethernet port). With this patch, we provide proper support for this device in ar71xx. Installation: - Flash factory image through stock firmware WEB UI or through TFTP - To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. - Rename factory image to recovery.bin - Stock TFTP server IP: 192.168.0.100 - Stock device TFTP address: 192.168.0.254 Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net> [Rebased onto revert commit, changed comments in mach-cpe510.c, changed commit title and description, fixed eth0 MAC address, removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: WNDR4300: fix WAN LED behaviourMichal Cieslakiewicz2019-10-211-2/+1
| | | | | | | | | Change WAN LED behaviour to be consistent with other Netgear routers running OpenWrt. Instead of link speed, use amber colour to indicate link status. Green LED should be used when Internet connection is up and running. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx: WNDR4300: use standard labels for buttonsMichal Cieslakiewicz2019-10-211-3/+3
| | | | | | | GPIO key labels have been changed to standard ones (rfkill, reset, wps). It does not affect button functionality. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx: remove unnecessary execute permission bitSungbo Eo2019-10-121-0/+0
| | | | | | .c files do not need to be executable. 644 is enough. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: bump 4.14 to 4.14.147Koen Vandeputte2019-10-082-15/+13
| | | | | | | | | | | | | Refreshed all patches. Altered patches: - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx) - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79) Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-0613-173/+173
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 01:00:16 +0000