aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump kernel 4.4 to version 4.4.147Matthias Schiffer2018-08-092-28/+5
| | | | | | | | target/linux/ar71xx/patches-4.4/103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch has been applied upstream; the two deleted brcm2708 patches have been useless even before (as the second one only reverted the first one). Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: bump kernel 4.4 to version 4.4.140Hauke Mehrtens2018-07-132-48/+1
| | | | | | | | | | These two patches: target/linux/ar71xx/patches-4.4/403-mtd_fix_cfi_cmdset_0002_status_check.patch target/linux/ramips/patches-4.4/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch are replaced by upstream commit 242dbd2b3df ("mtd: cfi_cmdset_0002: Change erase functions to check chip good only") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: fix 5 GHz Wi-Fi on NBG6716Matti Laakso2018-06-221-1/+7
| | | | | | | | | | Some NBG6716 do not have ath10k calibration data in flash, only in chip OTP. To determine if flash has a valid calibration data, the first two bytes telling the length of the calibration data are checked against the requested length. If the lengths match, calibration data is valid and read from flash. Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
* kernel: bump kernel 4.4 to version 4.4.137Hauke Mehrtens2018-06-152-1/+2
| | | | | | | | | | | | The new option CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE was added, in this commit: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/commit/?h=linux-4.4.y&id=ffe4bf3eb3cfa10f9ef295c08c21f4fe3bb07e21 Handle it by setting it to the opposite value CONFIG_CC_OPTIMIZE_FOR_SIZE is set to. Tested on lantiq Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump kernel 4.4 to 4.4.135 for 17.01Hauke Mehrtens2018-06-021-1/+1
| | | | | | * Refreshed patches Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: Deactivate build of Netgear WNR2000v3Hauke Mehrtens2018-06-021-1/+2
| | | | | | | | | This devices always looses the settings after power loss, nothing is been saved. Deactivate building this image till this problem is fixed. See FS#672 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: fix and improve ALFA Network Tube2H supportPiotr Dymacz2018-05-091-1/+12
| | | | | | | | | Fix ART offset (make it universal for 8/16 MB versions of the board) and while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B). Fixes: FS#1532 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: bump kernel 4.4 to 4.4.131 for 17.01Etienne Haarsma2018-05-072-10/+10
| | | | | | | | | * Refreshed patches Compile-tested: ar71xx Run-tested: ar71xx Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com>
* kernel: bump kernel 4.4 to 4.4.129 for 17.01Etienne Haarsma2018-04-302-7/+7
| | | | | | | | | * Refreshed patches Compile-tested: ar71xx Run-tested: ar71xx Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com>
* ar71xx: Ubiquiti Airmax M: add relocate-kernel to invalidate cacheMatthias Schiffer2018-04-261-0/+1
| | | | | | | | | | | | | | Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956 (Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the caches for the whole kernel address range after decompressing the kernel image, leading to hard to debug boot failures, depending on kernel version and configuration. As a workaround, prepend the relocate-kernels loader, which will invalidate the caches after moving the kernel to the correct load address. Reported-by: Andreas Ziegler <dev@andreas-ziegler.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: sysupgrade: improve CPE/WBS 210/510 validation, add new metadata offsetMatthias Schiffer2018-04-101-12/+20
| | | | | | | | | Previously, tplink_pharos_check_image() would accept any image with ELF magic and only non-printable data in the support-list, as in this case the while-read loop would not run at all. Add the new support-list offset and ensure an image is only accepted when the model string is actually found. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* Kernel: bump 4.4 to 4.4.124 for 17.01Stijn Segers2018-04-011-1/+1
| | | | | | | | | | * Refreshed patches * Removed 087-Revert-led-core-Fix-brightness-setting-when-setting-.patch (applied upstream) Compile-tested on ar71xx, ramips/mt7621, x86/64 Run-tested on ar71xx Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* kernel: bump 4.4 to 4.4.120 for 17.01Stijn Segers2018-03-041-1/+1
| | | | | | | | | Bump the 4.4 kernel for the 17.01 release to 4.4.120. Refresh patches. Compile-tested: ar71xx, ramips/mt7621, x86/64 Run-tested: ar71xx, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* kernel: update 17.01 kernel to 4.4.116Stijn Segers2018-02-202-7/+10
| | | | | | | | | | | | | | | | | | This bumps the 4.4. kernel in LEDE 17.01 to 4.4.116. More Meltdown & Spectre mitigation. * Refresh patches. * Refresh x86/config for RETPOLINE. * Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream) * Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream) * 650-pppoe_header_pad.patch does not apply anymore (code was replaced). Bumps from 4.4.113 to 4.4.115 were handled by Kevin Darbyshire-Bryant. Compile-tested on: ar71xx, ramips/mt7621, x86/64 Run-tested on: ar71xx, ramips/mt7621, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ar71xx: remove bs-partition ro-flag for UniFi ACDavid Bauer2018-02-111-1/+1
| | | | | | | | | | | | This removes the read-only flag from the bs (bootselect) partition on UniFi AC devices. This allows to correct the indicator from which partition the device is booting its kernel from. See also: - https://github.com/freifunk-gluon/gluon/issues/1301 - https://bugs.lede-project.org/index.php?do=details&task_id=662 Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: /lib/ar71xx.sh: add model detection for TP-Link TL-WR810NMatthias Schiffer2018-02-031-0/+3
| | | | | | Properly report the revision in /tmp/sysinfo/model. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: bump 4.4 to 4.4.112 for 17.01Kevin Darbyshire-Bryant2018-01-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: target/linux/generic/patches-4.4/030-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch target/linux/generic/patches-4.4/030-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch target/linux/generic/patches-4.4/030-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch target/linux/generic/patches-4.4/030-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch CVEs completely or partially addressed: CVE-2017-5715 CVE-2017-5753 CVE-2017-17741 CVE-2017-1000410 Compile-tested: ar71xx Archer C7 v2 Run-tested: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ar71xx: Netgear WNR2000v4: do not include USB packages [17.01]Stijn Segers2018-01-131-1/+0
| | | | | | | | | The Netgear WNR2000v4 does not have a USB port. Hence, including USB packages into the default images is useless. It looks like the WNR2000v4 definition in master is OK. v2 fixes the silly typo in the patch title (WNR2000v4 instead of WNR200v4) Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ag71xx: Fix rx ring buffer stall on small packets flood on qca956x and qca953x.Vittorio Gambaletta2018-01-093-1/+22
| | | | | | Backported from Code Aurora QSDK Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
* ar71xx: QCA956X: add missing registerHenryk Heisig2018-01-096-4/+66
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* kernel: update kernel 4.4 to version 4.4.110Hauke Mehrtens2018-01-071-1/+1
| | | | | | This fixes: CVE-2017-5754 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.4 to 4.4.107Etienne Haarsma2017-12-233-3/+3
| | | | | | | | | | | | | Bump 4.4 to 4.4.107 and refreshed all patches. Made the following patch for Mediatek and Oxnas compatible with kernel 4.4.107: 0072-mtd-backport-v4.7-0day-patches-from-Boris.patch Compile-tested: ar71xx Run-tested: ar71xx Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com> Reviewed-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Rosen Penev <rosenp@gmail.com>
* ar71xx: fix switch port numbering on RB750r2 and RB750UPr2João Chaínho2017-12-131-0/+6
| | | | | | | | This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite). Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them. Signed-off-by: João Chaínho <joaochainho@gmail.com> (cherry picked from commit 61027e343025b5f47e7e79db71576e6bd5e97c1d)
* kernel: bump 4.4 to 4.4.103 for 17.01Etienne Haarsma2017-12-123-3/+3
| | | | | | | | | | | | | Refreshed all patches. Removed upstream ramips patches: 0101-MIPS-ralink-Fix-MT7628-pinmux.patch 0102--MIPS-ralink-Fix-typo-in-mt7628-pinmux-function.patch Compile-tested: ar71xx Run-tested: ar71xx Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com>
* kernel: bump 4.4 to 4.4.102Etienne Haarsma2017-11-261-3/+3
| | | | | | | | | | | | Refreshed all patches. Removed upstream ramips patch: 0063-set-CM_GCR_BASE_CMDEFTGT_MEM-according-to-datasheet.patch Compile-tested: ar71xx Run-tested: ar71xx Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com> Tested-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx: fix LED config for DIR-869 A1Florian Beier2017-11-031-7/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the LED configuration for the D-Link DIR-869 A1. In order to support the device I probed around using an initramfs image for the UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them. GPIO 16 set to low meant that the color was white while pulling it to high made the color change to orange. The past code was written based upon these findings. However, running a flashed image I now discovered that GPIO 15 controls the orange LEDs while GPIO 16 controls the white ones and that both are active when low. This means that the GPIOs were inverted and one active_low was set wrong which this patch fixes. Behavior of the LED front after this patch is applied: cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness 0 -> white LEDs are OFF 255 -> white LEDs are ON cat /sys/devices/platform/leds-gpio/leds/d-link:orange:status/brightness 0 -> orange LEDs are OFF 255 -> orange LEDs are ON If the brightness of both is set to 255 the LED front will be white. If the brightness of both is set to 0 the LED front will be off. Signed-off-by: Florian Beier <beier.florian@gmail.com>
* ar71xx: add rssileds to WA850RE v1 imageMathias Kresin2017-10-071-0/+1
| | | | | | | | | | | | A default rssileds config exists for the TP-Link WA850RE v1 but the rssiled package is not included by default. The compressed 17.01.3 image size increases by 3302 bytes which should be tolerable even for a 4MB flash board. Fixes: FS#1043 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: fix MAC addresses on TP-Link TL-WR1043ND v4Matthias Schiffer2017-09-112-2/+3
| | | | | | | | | | The addresses were read from the 'config' partition, which would not always contain the addresses at the same offsets, depending on the stock firmware version used before flashing LEDE. Change this to get the addresses from the 'product-info' partition, which is read-only. Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: update 4.4 to 4.4.86Kevin Darbyshire-Bryant2017-09-041-1/+1
| | | | | | Refresh patches Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: update kernel 4.4 to version 4.4.79Hauke Mehrtens2017-07-282-43/+6
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: fix switch port mapping for TP-Link TL-WR74xN/D seriesPiotr Dymacz2017-07-231-1/+1
| | | | | | | | | Backport of ad8c315: "ar71xx: fix switch port mapping for TP-Link TL-WR74xN/D series". Fixes FS#843 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP121FPiotr Dymacz2017-07-2313-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users. Device is based on Atheros AR9331 WiSoC and is running a custom version (updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR1) - 16 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz - 1x microSD (optional, on separate PCB) - 3x LED, 1x button, 1x switch - UART header on PCB Flash instruction (under U-Boot web recovery mode): 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: set US region code for TP-Link TL-WR710N v1 imageMatthias Schiffer2017-07-121-0/+1
| | | | | | | Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so far, so we can just set US unconditionally. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: Fix UBIFS work on Mikrotik RB95x devicesSergey Sergeev2017-07-051-0/+2
| | | | | | | | If nand chip has no NAND_NO_SUBPAGE_WRITE flag on its options ubifs can't use it mtd devices and the kernel crashes with error: __nand_correct_data: uncorrectable ECC error Signed-off-by: Sergey Sergeev <adron@yapic.net>
* ar71xx: fix Wallys DR344 GPIO-connected LEDs and buttonPiotr Dymacz2017-05-303-10/+33
| | | | | | | | | | | | | | | | | | | | This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board and sets color of all LEDs to green as the mass production boards have only green one. Actually, DR344 has 6 GPIO-connected LEDs and one button: - GPIO11: status - GPIO12: sig1 - GPIO13: sig2 - GPIO14: sig3 - GPIO15: sig4 - GPIO16: reset button - GPIO17: lan WAN LED is connected directly with AR8035 PHY. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: set GE interface as wan by default in Wallys DR344Piotr Dymacz2017-05-301-1/+1
| | | | | | | This aligns default network interfaces configuration with vendor firmware: GE (eth0) -> wan, FE (eth1) -> lan. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix GE interface support in Wallys DR344Piotr Dymacz2017-05-301-30/+8
| | | | | | | | GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with AR8035, not with AR8327. Without this fix, GE interface doesn't work at all or shows high packet loss ratio. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: update kernel 4.4 to 4.4.69Stijn Segers2017-05-241-2/+2
| | | | | | | | | | | | | | | | | | | | | Bump the 17.01 tree kernel to 4.4.69. Trunk 4.4 and 17.01 4.4 have diverged, talked this through with jow, he was okay with a clean diff against 17.01 and not a backported trunk patch. The following patches were applied upstream: * 062-[1-6]-MIPS-* series * 042-0004-mtd-bcm47xxpart-fix-parsing-first-block Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup, as it was incorrectly included upstream thus dropped from LEDE, but subsequently reverted upstream. Thanks to Kevin Darbyshire-Bryant for pointing me to it. Compile-tested on: ar71xx, ramips/mt7621, x86/64. Run-tested on: ar71xx, ramips/mt7621, x86/64. Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx: enable nand-utils in the mikrotik subtarget to ensure it makes it to ↵Felix Fietkau2017-05-122-2/+4
| | | | | | | | initramfs Without it, sysupgrade from initramfs to nand fails Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: select ATH79_NVRAM only by boards actually use itPiotr Dymacz2017-04-281-4/+5
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix minor syntax error in /lib/upgrade/platform.shMatthias Schiffer2017-04-221-1/+1
| | | | | | | Fix a '==' that should be a '=' in a test condition. Busybox fortunately doesn't care. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add TP-LINK TL-WR841N/ND v12 imageVittorio Gambaletta2017-04-201-1/+7
| | | | | | | | | | | | | This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC ID, same TFTP image name...). If the stock firmware web interface doesn't accept LEDE factory image, it can be flashed via the U-Boot TFTP recovery mode, by long-pressing the reset button after power on. The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12). Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
* ar71xx: fix Wallys DR344 ethernet MAC addresses offsetsPiotr Dymacz2017-04-021-2/+3
| | | | | | | Without this fix, ethernet interfaces on Wallys DR344 use random MAC addresses. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: update kernel 4.4 to 4.4.59Hauke Mehrtens2017-04-021-2/+2
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: add ath10k driver and firmware for Netgear R6100 to firmware imageStijn Segers2017-03-111-1/+1
| | | | | | | | A Netgear R6100 owner reported the LEDE images lack the ath10k driver and firmware [1]. This patch adds both to the R6100 image. [1] https://forum.lede-project.org/t/netgear-r6100-5ghz-wifi-not-working-after-initial-install/2222 Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx: fix platform_find_rootfspart()Thibaut VARENE2017-03-011-1/+1
| | | | | | | | platform_find_rootfspart() fails if the kernel partition comes before the rootfs partition. The proposed patch fixes this while preserving what I understand was the original idea: stop at first match. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* kernel: update kernel 4.4 to version 4.4.50Jo-Philipp Wich2017-02-201-11/+11
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: Remove images for rb-941-2ndThibaut VARENE2017-02-191-2/+0
| | | | | | | | | | The code that generates this image is broken in many ways. The new code currently in master generates images that will not be compatible with the ones in 17.01. To avoid a migration nightmare, this patch removes image generation for this device in 17.01 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: fix ethernet PLL configuration for QCA956xFelix Fietkau2017-02-171-1/+1
| | | | | | | QCA956x is configured like AR934x, not like the older chips. Should fix ethernet hangs when using the WAN port without SGMII Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix DEFAULT_PACKAGES for mikrotik devicesFelix Fietkau2017-02-151-1/+2
| | | | | | Include packages from the default profile for NAND devices Signed-off-by: Felix Fietkau <nbd@nbd.name>