aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx/generic: enable Zyxel NBG6616 in kernel config againMatthias Schiffer2018-08-271-0/+1
| | | | | | | | The NBG6616 shares a config symbol with the NBG6716. It was accidentally removed from the config when the ar71xx-tiny target was split off. Fixes: 0cd5e85e7ad6 ("ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: fix typo in rb91x nand sourceKoen Vandeputte2018-08-241-1/+2
| | | | | | Fixes: 3b1ea0996f83 ("ar71xx: fix build error due to bad include") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.66Koen Vandeputte2018-08-2244-356/+218
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix build error due to bad includeKoen Vandeputte2018-08-224-5/+20
| | | | | | | | | | | | | | | | | | While "rawnand.h" is available in kernel 4.14, the default for this target is kernel 4.9 in which "nand.h" should be used. Add an extra check to include the correct file depending on kernel version Fixes these build errors: drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory #include <linux/mtd/rawnand.h> ^~~~~~~~~~~~~~~~~~~~~ compilation terminated. Fixes: 318e19ba6755 ("ar71xx: add v4.14 support") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: add missing include for checking kernel versionKoen Vandeputte2018-08-2210-0/+10
| | | | | | | | | | | | | | | | | | Fixes these build errors: arch/mips/ath79/mach-rb2011.c:20:5: error: "LINUX_VERSION_CODE" is not defined, evaluates to 0 [-Werror=undef] #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^~~~~~~~~~~~~~~~~~ arch/mips/ath79/mach-rb2011.c:20:26: error: "KERNEL_VERSION" is not defined, evaluates to 0 [-Werror=undef] #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^~~~~~~~~~~~~~ arch/mips/ath79/mach-rb2011.c:20:40: error: missing binary operator before token "(" #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0) ^ Fixes: 318e19ba6755 ("ar71xx: add v4.14 support") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: add v4.14 supportJohn Crispin2018-08-22164-78/+8268
| | | | | | adds v4.14 patches for testing but leaves v4.9 as default for now. Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 4.9 to 4.9.119Koen Vandeputte2018-08-102-14/+8
| | | | | | | | | | | | Refreshed all patches. Delete upstreamed patch: - 100-tcp-add-tcp_ooo_try_coalesce-helper.patch Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-08-091-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros QCA9558. Ported from ar71xx target. Specification: - Qualcomm Atheros QCA9558 - 64 MB of RAM - 16 MB of Flash - 5x 10/100/1000 Ethernet - QCA8337N - 4x LEDs, 2x keys - UART header on PCB - Vcc, TX, RX, GND from LED side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Connect power cable to BHR-4GRV2 and turn on it 3. Access to "http://192.168.12.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新実行") button 5. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ar71xx: allow to override at803x sgmii aneg statusDavid Bauer2018-08-082-0/+43
| | | | | | | | | | | | | When checking the outcome of the PHY autonegotiation status, at803x currently returns false in case the SGMII side is not established. Due to a hardware-bug, ag71xx needs to fixup the SoCs SGMII side, which it can't as it is not aware of the link-establishment. This commit allows to ignore the SGMII side autonegotiation status to allow ag71xx to do the fixup work. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix QCA955X SGMII link lossDavid Bauer2018-08-085-0/+127
| | | | | | | | | | | | | | | | | | | The QCA955X is affected by a hardware bug which causes link-loss of the SGMII link between SoC and PHY. This happens on change of link-state or speed. It is not really known what causes this bug. It definitely occurs when using a AR8033 Gigabit Ethernet PHY. Qualcomm solves this Bug in a similar fashion. We need to apply the fix on a per-device base via platform-data as performing the fixup work will break connectivity in case the SGMII interface is connected to a Switch. This bug was first proposed to be fixed by Sven Eckelmann in 2016. https://patchwork.ozlabs.org/patch/604782/ Based-on-patch-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.9 to 4.9.118Koen Vandeputte2018-08-071-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: add support for TP-LINK CPE510 V2.0Andrew Cameron2018-08-022-2/+22
| | | | | | | | Adds Support for the TP-LINK CPE510 V2.0 by TP-Link. The hardware is almost the same as the CPE510 V1.0 Follow the same processes as for the CPE510 V1.0 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* Revert "ar71xx: ag71xx: Prevent kernel oops for board def"Jo-Philipp Wich2018-08-011-15/+1
| | | | | | | | | | | This reverts commit 7a3e133751870a3431e2430386a77a002eb24117. This change reportedly breaks connectivity on some ar71xx devices, so revert it for now. Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087 Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* Revert "ar71xx: ag71xx: Add connect message: fixed phy"Jo-Philipp Wich2018-08-011-7/+0
| | | | | | | | | | | This reverts commit 0b9f4e880807e3cfd22d12b929202e1edcdc577c. This change reportedly breaks connectivity on some ar71xx devices, so revert it for now. Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087 Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* Revert "ar71xx: ag71xx_phy: Fix compilation for debug messages"Jo-Philipp Wich2018-08-011-4/+2
| | | | | | | | This reverts commit 2655fbe8efb2a596aa8db92cffa817e3bf0c64ea. The patch introduces syntax errors, revert it for now. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: cr3000: cleanup board definitionDaniel F. Dickinson2018-08-011-16/+23
| | | | | | | | | | | | | 1) Add comments so it's clear why we did things; this may prevent someone (e.g. me) from sinking time into fixing things that aren't broken and/or were done for reason. 2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0. 3) Cosmetic reording of some code (tested) that makes the defintion more clear. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr3000: Use correct company nameDaniel F. Dickinson2018-08-013-3/+3
| | | | | | It's 'PowerCloud Systems' not 'PowerCloud'. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr3000: Drop support for defunct cloudDaniel F. Dickinson2018-08-011-11/+2
| | | | | | | | | The CR3000 stock firmware is now irrelevant as it required a now defunct cloud service. Therefore only build images that use the entire flash (overwriting stock firwmare-specific partitions that no longer matter), previously called 'nocloud' images. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* kernel: bump 4.9 to 4.9.116Koen Vandeputte2018-08-017-109/+17
| | | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches Remove upstreamed patches. - 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch - 403-mtd_fix_cfi_cmdset_0002_status_check.patch - 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch - 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - 900-gen_stats-fix-netlink-stats-padding.patch Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112 - backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch This patch has been slightly altered to compensate for a new helper function introduced in later kernels. Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9 Compile-tested on: ar71xx, bcm2710 Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: re-add patch for AT8032 Ethernet PHYDaniel Golle2018-07-311-4/+4
| | | | | | | | | | The patch was wrongly removed by a kernel version bump to 4.9.105 in the believe that it was merged upstream thow it wasn't. This lead to unrecoverable link losses on devices which use those PHYs such as many ubnt single-port CPEs. Fixes: 7dca1bae82 (kernel: bump to 4.9.105) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ar71xx: define switch for rb-952ui-5ac2ndThibaut VARÈNE2018-07-301-2/+2
| | | | | | | QCA9533 built-in switch can be configured Tested-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: fix TL-WR1043N v5 port mappingJohn Crispin2018-07-301-1/+4
| | | | | | fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.") Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.Tim Thorpe2018-07-301-1/+1
| | | | | | Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing. Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
* ar71xx: TL-WR1043N v4/v5: add orange WAN LED supportTim Thorpe2018-07-301-3/+14
| | | | | | | | | | | Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and v5. Change the name of a MAC address offset constant to make it consistent with the format of the existing constants. Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
* ar71xx: add support for TP-Link Archer C59 v2Keith Maika2018-07-3012-5/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* ar71xx:add support for E750G v8张鹏2018-07-3012-2/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E750G v8 is based on Qualcomm QCA9344. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4G GHz (AR9344) - 2x 10/100 Mbps Ethernet (PoE support) - 2x 10/100/1000 Mbps Ethernet - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
* ar71xx:add support for E750A v4张鹏2018-07-3011-1/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E750A v4 is based on Qualcomm QCA9344. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 5G GHz (AR9344) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 7x LED (6 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J23) and LEDs (J2) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
* ar71xx:add support for E558 v2张鹏2018-07-3012-0/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9558) - 3x 10/100/1000 Mbps Ethernet (one port with PoE support) - 4x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 3-pos switch - 1x DC jack for main power input (9-48 V) - UART (JP5) and LEDs (J8) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com>
* ar71xx: ag71xx: Prevent kernel oops for board defDaniel F. Dickinson2018-07-301-1/+15
| | | | | | | | | | | The driver is written in such a way that with a board defintion that connects a fixed phy, mdio, and switch in a certain way, a kernel oops could result because of lack of previously probed mdio bus. This commit allows for easier debugging in this case by casting the correct blame with serial console messages. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: ag71xx: Add connect message: fixed phyDaniel F. Dickinson2018-07-301-0/+7
| | | | | | | | It's a little noisier but makes it obvious when the ar7240 switch was connected to the MDIO bus, and to which phy device (or the failure to do so). Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: ag71xx_phy: Fix compilation for debug messagesDaniel F. Dickinson2018-07-301-2/+4
| | | | | | | | | | | NB: Error only appears with ag71xx debug messages and dynamic printk enabled. This is probably why no one has caught it before. Previously phy probe debug messages used old (now wrong) functions to get the phy name for printing. There was also the chance of a NULL pointer in the event no phy_device was found. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cap324: Drop support for defunct cloudDaniel F. Dickinson2018-07-301-11/+2
| | | | | | | | | Only build images for straight OpenWrt (using all flash; wipes out partitions that contain information only important for accessing a now defunct cloud service with the stock firmware) since the stock firmware is now irrelevant. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cap324: Use correct company nameDaniel F. Dickinson2018-07-304-5/+5
| | | | | | It's 'PowerCloud Systems' not just 'PowerCloud' Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cap324: Use correct MAC addressesDaniel F. Dickinson2018-07-301-3/+3
| | | | | | | The wrong MAC addresses (from the point of view of the physical device label) were being assigned to the wrong interfaces. Fix that. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cap324: Use standard eth as static lanDaniel F. Dickinson2018-07-301-1/+1
| | | | | | | | | | While the stock firmware and previous ar71xx versions of openwrt used the single ethernet port as a DHCP client, for unmodified openwrt usage it makes more sense to do the standard openwrt thing and make the ethernet port a static lan with known address so that users can find the device on the network more easily. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr5000: use correct company nameDaniel F. Dickinson2018-07-302-3/+3
| | | | | | It's 'PowerCloud Systems' not just 'PowerCloud' Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr5000: Drop support for defunct cloudDaniel F. Dickinson2018-07-301-12/+2
| | | | | | | The Skydog cloud service no longer exists hence supporting going back to stock firmware with cloud support is no longer applicable. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr5000: Tweak switch LED settingsDaniel F. Dickinson2018-07-301-4/+4
| | | | | | | This is basically cosmetic and sets the Port 1-4 LEDs to blink on 10/100/1000M. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr5000: Fix the reset button as KEY_RESTARTDaniel F. Dickinson2018-07-301-1/+1
| | | | | | | The reset button was incorrectly returning KEY_WPS_BUTTON as the key code. We want KEY_RESTART., so make that fix. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr5000: board data: Use better macro nameDaniel F. Dickinson2018-07-301-2/+2
| | | | | | | The PCIe wireless MAC address address is better labelled as WMAC than MAC to emphasize that it is for a wireless interface. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: improve MikroTik wAP R supportThibaut VARÈNE2018-07-303-2/+67
| | | | | | | | | | | | | 81d446b045176e3e25bb0ef74e3d060b51a0a353 introduced incomplete support for this device. This patch attempts to correct the situation based on OEM source code. LED1-3 are GSM mode on OFW (2G/3G/4G) hence unassigned here. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Tested-by: David Ehrmann <ehrmann@gmail.com>
* ar71xx: add missing diag LED support for RB wAP 2nDThibaut VARÈNE2018-07-301-1/+2
| | | | | | | 3b15eb06c366cf3805590a61f22e966a95bf8101 did not include diag.sh edit Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: rbspi: mark rb911L user led as active lowThibaut VARÈNE2018-07-301-1/+4
| | | | | | | | | | | | The active_low flag was missing for the user LED. This LED is open drain (confirmed in OEM source) and open drain only makes sense for active low GPIOs. The two wireless LEDs mentioned in the comments are also #defined for future reference. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Tested-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: rbspi: fix RB wAP AC gpio conflict and LEDThibaut VARÈNE2018-07-302-11/+9
| | | | | | | | | | | | | | | e15c63a37574bd15ce3a6636c2f04741ab76f7b9 introduced code that was trying to register GPIO 1 as both an LED and a button. The OEM source makes it clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button. Furthermore the (green) power led default state should also be defined, (matching OEM source), and it should be used by diag.sh since it's currently the only software-controllable LED. This patch fixes these issues and renames the corresponding #defines for clarity Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: rbspi: clarify USB power gpios actionThibaut VARÈNE2018-07-301-10/+9
| | | | | | | | | | | | | | | The gpios that control power toggle for USB on the RouterBOARD devices are active low _off_ switches. When they are active (low), power is off. When they are inactive (high), power is on. Rename GPIO defines, set gpios to GPIOF_ACTIVE_LOW for consistency and reflect their true action in the display name. This brings openwrt code in line with OEM. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Tested-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: Move F9K1115v2 under ar71xx tiny targetKin Chan2018-07-165-10/+10
| | | | | | | | | | | | F9K1115v2 has a kernel partition size of 1408 kB. Since kernel 4.9.x+ the kernel image for this device compiled had exceeded the kernel partition size limit and thus failing size check. The kernel image generated for this device under ar71xx tiny target is 1329.67 kB < 1408 kB. Signed-off-by: Kin Chan <kcchan1@outlook.com>
* ar71xx: add support for MikroTik RB931-2nDThibaut VARÈNE2018-07-169-2/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RB931-2nD (hAP mini): https://mikrotik.com/product/RB931-2nD Specifications: * SoC: Qualcomm QCA9533 (650MHz) * RAM: 32MiB * Storage: 16MiB SPI NOR flash * Ethernet: 3x100M * Wireless: QCA9533 built-in, dual-chain 802.11b/g/n Installation: 1. Setup a DHCP/BOOTP Server with the following parameters: * DHCP-Option 66 (TFTP server name): pointing to a local TFTP server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename of the to be booted image. The usable intramfs files are: - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin 2. Press the reset button on the board and keep that pressed. 3. Connect the board to your local network via its Internet port. 4. Release the button after the LEDs on the board are turned off. Now the board should load and start the initramfs image from the TFTP server. 5. Now connect the board via either of its LAN ports (2 or 3). 6. Upload the sysupgrade image to the board with scp: $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin 7. Log in to the running system listening on 192.168.1.1 via ssh as root (without password): $ ssh root@192.168.1.1 8. Flash the uploaded firmware file from the ssh session via the sysupgrade command: root@OpenWrt:~# sysupgrade /tmp/fw.bin Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ar71xx: move boards to tiny subtargetMathias Kresin2018-07-125-35/+36
| | | | | | | Move boards to the tiny subtarget which break the build if the kernel is set to "Optimize for performance". Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: factor out safe loader image build codeMathias Kresin2018-07-073-60/+44
| | | | | | | | | | Add a template for safeloader images and include it instead of overwriting variables defined in the common tp-link build commands. Split the existing tp-link templates to proper implement the safeloader template. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: drop unnecessary LOADER_TYPE variablesMathias Kresin2018-07-071-5/+1
| | | | | | | Drop the LOADER_TYPE variables in case no loader is used at all or move the variable to devices which are using a loader. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 05:39:42 +0000