aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: image: simplify Meraki MR16 device definitionPiotr Dymacz2017-07-091-10/+2
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix upgrade platform check for Compex WPJ558Enrique Giraldo2017-07-091-1/+1
| | | | | | The magic number was wrong and always marked the images as invalid. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
* ar71xx: support LED in TP-Link TL-WR902AC RJ45 socketPiotr Dymacz2017-07-092-3/+8
| | | | | | | | | TP-Link TL-WR902AC has another one, tiny LED inside RJ45 socket which is attached to GPIO15. Add support for it, use it as a "lan" LED and rename old one to "internet". Also, fix uci option name for "lan" LED in system configuration ("wan" -> "lan"). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: verify TP-Link TL-WR902AC sysupgrade imagePiotr Dymacz2017-07-091-2/+2
| | | | | | | Until we enable requirement for metadata in sysupgrade images under ar71xx target, this prevents users from using wrong image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add metadata to some TP-Link imagesHenryk Heisig2017-07-091-2/+9
| | | | | | | This commit adds metadata to TP-Link sysupgrade images created by tplink-safeloader with uImage kernel header. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855REPiotr Dymacz2017-07-041-2/+2
| | | | | | | Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices. Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID") Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix Netgear WNDR3700 v4 switch port mappingQian Zheng2017-07-041-2/+2
| | | | Signed-off-by: Qian Zheng <sotux82@gmail.com>
* ar71xx: add support for TP-Link TL-WR902AC v1Piotr Dymacz2017-07-0414-3/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FWPiotr Dymacz2017-07-043-0/+3
| | | | | | | | We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel with TP-Link header embedded inside "safeloader" image type and thus get rid of statically defined "kernel" and "rootfs" partitions in cmdline. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: refresh and cleanup mikrotik subtarget kernel configPiotr Dymacz2017-07-041-8/+2
| | | | | | | Refresh mikrotik subtarget kernel config and enable kernel support for boards which belong to this subtarget only. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: refresh and cleanup nand subtarget kernel configPiotr Dymacz2017-07-041-5/+19
| | | | | | | Refresh nand subtarget kernel config and enable kernel support for boards which belong to this subtarget only. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: refresh and cleanup target kernel configPiotr Dymacz2017-07-041-9/+9
| | | | | | | Refresh target kernel config and disable kernel support for all boards which belong to nand and mikrotik subtargets only. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix typo in network defaultsJo-Philipp Wich2017-06-291-1/+1
| | | | | | | | Commit 9fec39a (ar71xx: add support for TP-Link TL-WA855RE v1) introduced a typo in 02_network, fix it by removing the stray paren. Reported-by: Henryk Heisig <hyniu@o2.pl> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: image: specify TPLINK_HWID for TP-Link RE450Piotr Dymacz2017-06-291-0/+1
| | | | | | | | | | TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin. As we don't want to break sysupgrade (all existing LEDE release images for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0. Fixes FS#852 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_IDPiotr Dymacz2017-06-291-13/+13
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix switch port mapping for TP-Link TL-WR74xN/D seriesPiotr Dymacz2017-06-291-1/+1
| | | | | | Fixes FS#843 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C58 v1Henryk Heisig2017-06-2915-7/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 3x button - UART header on PCB, RX, TX at TP4+5 (backside) QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to patch macaddress. Flash instruction: Use "factory" image directly in vendor GUI. Recovery method: 1. Set PC to fixed ip address 192.168.0.66/24. 2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and rename it to "tp_recovery.bin". 3. Start a tftp server with the file "tp_recovery.bin" in its root directory. 4. Turn off the router. 5. Press and hold Reset button. 6. Turn on router with the reset button pressed and wait ~15 seconds. 7. Release the reset button and after a short time the firmware should be transferred from the tftp server. 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f020000 +$filesize cp.b $fileaddr 0x9f020000 $filesize reset This commit is based on GitHub PR#1112 Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for TP-Link TL-WA855RE v1Federico Cappon2017-06-2912-6/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/397/198 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x external antennas - 2x LED (green and orange in the same package), 2x button - UART: TP5(TX) and TP4(RX) test points on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in EU version of the device, but should work also with the same device version sold in other countries. Signed-off-by: Federico Cappon <dududede371@gmail.com>
* ar71xx: fix EnGenius ENS202EXT mtd definitionPiotr Dymacz2017-06-291-4/+4
| | | | | | | | | | | | | | Use statically defined sizes for kernel and rootfs mtd partitions. Vendor upgrade script writes both firmware parts independently which ends up in a gap between kernel and rootfs images. This results in incorrectly calculated rootfs_data start offset. Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL definition. Fixes FS#835 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: move Arduino Yun to generic building codeCamille Bilodeau2017-06-293-8/+10
| | | | | | | | | | | | | | | | | | Migrate Arduino Yun from legacy to generic building code. Note: the mtd partitioning is changed to adopt the LEDE default partitioning. It allows to have a kernel bigger than 1280k. It is necessary as kernel > 4.4 with default LEDE configuration grows bigger. To use the new partitioning, you need to update your U-Boot env in advance: setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro" setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000" saveenv Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
* ar71xx: remove Arduino Yun 8 MiB prototypeCamille Bilodeau2017-06-292-8/+0
| | | | | | | | | The Arduino Yun has 16 MiB flash. Early prototype boards with 8 MiB were not available for sell: https://blog.arduino.cc/2013/08/21/updating-about-arduino-yun-and-arduino-robot/ Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
* ar71xx: wpj344: set MAC on wanLeon M. George2017-06-291-0/+3
| | | | Signed-off-by: Leon M. George <leon@georgemail.eu>
* ar71xx: wpj344: remove unused eth1 deviceLeon M. George2017-06-291-8/+0
| | | | Signed-off-by: Leon M. George <leon@georgemail.eu>
* ar71xx: wpj344: read MAC addresses from u-boot mtdLeon M. George2017-06-291-4/+5
| | | | | | | This way, the assigned addresses match those on the barcode labels. Otherwise, the addresses appear to vary on boot. Signed-off-by: Leon M. George <leon@georgemail.eu>
* kernel: cleanup CONFIG_SCHED_HRTICKStijn Tintel2017-06-291-1/+0
| | | | | | | Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the generic config in b47fd7656336162360ebf66147326763ddae3f8d. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: update kernel 4.4 to 4.4.74Stijn Tintel2017-06-2712-22/+22
| | | | | | | | Refresh patches. Compile-tested on ar71xx. Runtime-tested on ar71xx. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx/images/senao: fix reproducible issue using tarAlexander Couzens2017-06-251-0/+1
| | | | | | | | Use deterministic sorting Use numeric owner/group Set uid/gid to 0 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/image: make tar calls reproducibleAlexander Couzens2017-06-252-3/+11
| | | | | | | | Use --mtime when SOURCE_DATE_EPOCH is set. Use gzip -n9z instead of tar z to remove timestamp in gzip header. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx: add AVM FRITZ!WLAN Repeater 300E supportMathias Kresin2017-06-2414-0/+205
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: AR7242 (Virian 400MHz) * RAM: 64 MB DDR (W9751G6JB-25) * Flash: 16MB SPI flash (S25FL129PIF) * WiFi: AR9382 (2.4/5GHz) + 2x SE2595L * LAN: 1x1000M (PEF7071V) To install LEDE via EVA bootloader, a FTP connection need to be established to 192.168.178.1 within the first seconds after power on: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add AR724x PCIe init fixesMathias Kresin2017-06-248-33/+175
| | | | | | | | | | | | Add upstream send AR724x PCIe patches to get the PCIe controller out of reset during driver init. The AVM Fritz 300E bootloader doesn't take care of releasing the different PCIe controller related resets which causes an endless hang as soon as either the PCIE Reset register (0x180f0018) or the PCI Application Control register (0x180f0000) is read from. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: image: simplify TP-Link devices definitionsPiotr Dymacz2017-06-111-86/+28
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: fix TP-Link TL-WR710N v2/v2.1 BOARDNAMEPiotr Dymacz2017-06-111-2/+2
| | | | | | | | | | All TP-Link TL-WR710N versions share the same machine code. This has been working since the beginning as we don't use double-quotes to protect spaces inside command line values. Thus, kernel interprets 'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: tp-link.mk: keep devices in alphabetical orderPiotr Dymacz2017-06-111-406/+399
| | | | | | | | Keep TP-Link devices definitions in alphabetical order whenever it's possible. Also group together similar devices or devices from the same series. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: cleanups in 10-ar922x-led-fixPiotr Dymacz2017-06-111-22/+20
| | | | | | | Fix code style, indentation and leading/trailing whitespaces in: /etc/hotplug.d/net/10-ar922x-led-fix Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: cleanups in 11-ath10k-caldataPiotr Dymacz2017-06-111-24/+24
| | | | | | | Fix code style and boards alphabetical order in: /etc/hotplug.d/firmware/11-ath10k-caldata Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C25 v1Ludwig Thomeczek2017-06-1114-0/+274
| | | | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [minor code style fixes, boards alphabetical order fixes, reworked commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR942N v1Serg Studzinskii2017-06-1114-2/+333
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: move WRTnode2Q to generic build targetPiotr Dymacz2017-06-113-8/+9
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: simplify Ubiquiti devices definitionsPiotr Dymacz2017-06-111-45/+29
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: mikrotik: shorten DEVICE_TITLEPiotr Dymacz2017-06-111-4/+4
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: use simply expanded variablesPiotr Dymacz2017-06-116-202/+202
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: update GL.iNet boards DEVICE_TITLEPiotr Dymacz2017-06-111-5/+5
| | | | | | | | Use "GL.iNet" as vendor name (based on information from the vendor, this is registered name of the company) and align model names with official website. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: fix 8devices boards DEVICE_TITLEPiotr Dymacz2017-06-111-2/+2
| | | | | | Be consistent with DEVICE_TITLE syntax and use vendor + board names. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: drop unused mtdlayouts from legacy.mkPiotr Dymacz2017-06-111-3/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: cosmetic: drop redundant empty linesPiotr Dymacz2017-06-115-23/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: add ROOTFS_SIZE to DEVICE_VARSPiotr Dymacz2017-06-111-4/+7
| | | | | | Also use ROOTFS_SIZE variable in place of static values. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: keep custom Build/* functions in separate filesPiotr Dymacz2017-06-113-53/+53
| | | | | | | | Most of the custom Build/* functions in ar71xx target are rarely used by image building code for devices from more than one subtarget. As they don't need to be always included, move them to corresponding *.mk files. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: keep DEVICE_VARS and Build/* at the beginningPiotr Dymacz2017-06-114-60/+60
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: simplify Compex devices definitionsPiotr Dymacz2017-06-111-20/+12
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: drop redundant kmod-usb-ohci from DEVICE_PACKAGESPiotr Dymacz2017-06-114-22/+22
| | | | | | kmod-usb-ohci is needed only on devices with AR71xx and AR7240 SoCs. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 14:30:13 +0000