aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: remove obsolete flash chip locking codeFelix Fietkau2016-12-125-52/+11
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove PB92 reference design board supportFelix Fietkau2016-12-1210-89/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP113 reference design board supportFelix Fietkau2016-12-1212-106/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP81 reference design board supportFelix Fietkau2016-12-1219-122/+10
| | | | | | This board is very old and unlikely to still be relevant today. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove obsolete duplicate driver source fileFelix Fietkau2016-12-121-294/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP83 reference design board supportFelix Fietkau2016-12-1218-661/+2
| | | | | | | | This board is very old and unlikely to still be relevant today. Support for it contains a significant amount of device specific baggage which is worth getting rid of. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: clean up spi controller related patchesFelix Fietkau2016-12-1223-667/+202
| | | | | | Remove various hacks for fast read, un-break device tree support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for YunCore SR3200 and XD3200Piotr Dymacz2016-12-1212-4/+256
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3Matthias Schiffer2016-12-064-3/+9
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: set GPIO reset line for Ubiquiti NanoStation Loco XWFelix Fietkau2016-12-041-0/+17
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for configuring at803x PHY GPIO reset via platform dataFelix Fietkau2016-12-041-0/+68
| | | | | | | Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW, because ar71xx is not converted to device tree yet. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix syntax error in /lib/ar71xx.shMatthias Schiffer2016-11-291-4/+4
| | | | | | | | Remove all comments in ubnt_xm_board_detect(), as it's not possible to add comments to specific lines of the case construct anyways. Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti" Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add model detection for UBNT Rocket TiMatthias Schiffer2016-11-291-1/+2
| | | | | Based-on-patch-by: Neal Oakey <neal.oakey@bingo-ev.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: remove squashfs-64k rootfs image from bin directory, the generic one ↵Felix Fietkau2016-11-291-1/+0
| | | | | | is enough Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove split kernel/rootfs images where the sysupgrade image can be ↵Felix Fietkau2016-11-291-17/+1
| | | | | | written to flash directly Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove 2MB flash variant of WP543Felix Fietkau2016-11-292-7/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove legacy devices that cannot be supported due to kernel ↵Felix Fietkau2016-11-292-38/+0
| | | | | | partition size limits Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove legacy gzip imagesFelix Fietkau2016-11-291-6/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove obsolete jffs2 image building codeFelix Fietkau2016-11-292-27/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: move DomyWifi DW33D to nand subtargetPiotr Dymacz2016-11-243-15/+11
| | | | | | | | | This device uses NAND FLASH, so it should be kept in nand subtarget. Also, inlcude in packages kmod-usb-ledtrig-usbport instead of obsolete kmod-ledtrig-usbdev. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: Fix switch config on Mikrotik RB450/GJoão Chaínho2016-11-211-2/+6
| | | | | | | This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G. The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged. Signed-off-by: João Chaínho <joaochainho@gmail.com>
* ar71xx: add support for YunCore CPE830Piotr Dymacz2016-11-2110-26/+131
| | | | | | | | | CPE830 is a clone of AP90Q, with different type of antenna (panel) and additional 4 LEDs for WiFi signal level indication. Use the same flash approach as for YunCore AP90Q. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE870Piotr Dymacz2016-11-2110-0/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341. Short specification: - 535/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm - internal 14 dBi panel antenna - 8x LED, 1x button - UART (JP1) header on PCB Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. setenv bootcmd "bootm 0x9f020000" 5. saveenv && reset Vendor firmware access (login/password): Admin/5up Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore AP90QPiotr Dymacz2016-11-2110-7/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2. Short specification: - 650/600/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz with external PA, up to 29 dBm - 2x internal 5 dBi omni antennas - 4x LED, 1x button - UART (JP1) header on PCB Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Flash instruction under vendor fimrware, using telnet/SSH: 1. Connect PC with 192.168.1.x address to WAN port 2. Power up device, enter failsafe mode with button (no LED indicator!) 3. Change root password and reboot (mount_root, passwd ..., reboot -f) 4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP 5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 6. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9f050000" - mtd erase firmware - mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E380AC v1 and v2Piotr Dymacz2016-11-2112-9/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035. There are two versions of this model, with different RAM and U-Boot mtd partition sizes: - v1: 128 MB of RAM, 128 KB U-Boot image size - v2: 256 MB of RAM, 256 KB U-Boot image size Version number is available only inside vendor GUI, hardware and markings are the same. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 1x 10/100/1000 Mbps Ethernet, with PoE support - 128 or 256 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm - 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm - 6x internal antennas - 1x RGB LED, 1x button - UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB - external watchdog (Pericon Technology PT7A7514) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530NPiotr Dymacz2016-11-2110-42/+329
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As we already have support for CF-E316N v2 and many devices from this vendor look similar, the support was included in existing mach-*.c file, with few cleanups and fixes. All 3 devices are based on Qualcomm/Atheros QCA9531 v2. COMFAST CF-E320N v2 is a ceiling mount AP with PoE support. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x RGB LED, 1x button - UART (J1), GPIO (J9) and USB (J2) headers on PCB - external watchdog (Pericon Technology PT7A7514) COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support. They seem to have different only the front panel. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, WAN with PoE support - 1x USB 2.0 (in CF-E520N covered by panel, available on PCB) - 32 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x LED, 1x button - UART (J1) headers on PCB Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix drivers/mtd/nand/ar934x_nfc.cPaul Wassi2016-11-181-8/+2
| | | | | | | Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw. Add *page* in the argument list and remove the local variable. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: enable serial console on mikrotik devicesJoão Chaínho2016-11-181-1/+4
| | | | | | | This patch enables the serial console on some Mikrotik devices (RB450, RB450G, RB493G, RB750UP). Signed-off-by: João Chaínho <joaochainho@gmail.com>
* kernel: update kernel 4.4 to version 4.4.32Stijn Tintel2016-11-161-2/+2
| | | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on all targets that use kernel 4.4 and aren't marked broken. Runtime-tested on ar71xx, octeon. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partitionHenryk Heisig2016-11-163-4/+8
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: Add usable, inactive LEDs on OpenMesh devicesJaylin Yu2016-11-161-0/+27
| | | | | | | | | | | OpenMesh devices have often LEDs which are not yet used by OpenWrt. These should still be available as disabled LEDs in the system configuration for easier modification. Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com> [sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh, add wifi/status LEDs] Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add support for Buffalo BHR-4GRV2FUKAUMI Naoki2016-11-1612-4/+218
| | | | Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
* ar71xx, ramips: reduce CPU load and flickering on devices using rssliedsMartin Weinelt2016-11-161-7/+7
| | | | | | | | | Polling every 40ms causes more than 10% CPU load on weak devices. An interval of 200ms is much more reasonable. Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net> [Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message] Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: enable HSR tuner on Ubiquiti UAP Outdoor+Matthias Schiffer2016-11-151-0/+1
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: fix DEVICE_TITLE for Ubiquiti UAP Outdoor+Matthias Schiffer2016-11-151-1/+1
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: generate region-coded factory images for TP-Link TL-WR841ND v11Matthias Schiffer2016-11-111-0/+3
| | | | | | | | The latest stock firmwares for US and EU regions have started checking the region code. Tested-by: Andreas Ziegler <ml@andreas-ziegler.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: fix kernel relocate stub parallel build issueFelix Fietkau2016-11-081-4/+5
| | | | | | Use per-kernel directory Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: tl-wpa8630: Fix kernel lenghtHenryk Heisig2016-11-081-1/+1
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: wpa8630: change board name to tl-wpa8630Henryk Heisig2016-11-0813-200/+202
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: Add support to Powerline ac TP-Link WPA8630Henryk Heisig2016-10-3112-2/+210
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: Add net config for MR12 & MR16Chris Blake2016-10-311-0/+2
| | | | | | | | | Both the MR12 and MR16 are single gigabit ethernet devices, similar to the MR18. This change gives them the correct network config on a fresh install. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> [Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: fix ethernet on wpj344 boardChristian Mehlis2016-10-311-0/+1
| | | | | | | | | In 814d70b2 the member mac06_exchange_en of struct ar8327_pad_cfg was changed to mac06_exchange_dis, but wpj344 was not adopted to stay in sync. Signed-off-by: Christian Mehlis <christian@m3hlis.de> Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
* ar71xx: add support for D-Link DAP-2695 rev. A1Stijn Tintel2016-10-2712-0/+269
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* ar71xx: build relocate stub for generic and legacy imagesStijn Tintel2016-10-272-7/+4
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* ar71xx/base-files: rename 09_fix-trx-header 09_fix-checksumStijn Tintel2016-10-271-0/+0
| | | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* kernel: mtdsplit: add support for WRGG imagesStijn Tintel2016-10-271-0/+1
| | | | | | | | Support splitting WRGG images, found in some D-Link devices (e.g. DAP-2695). Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: John Crispin <john@phrozen.org>
* ar71xx: Ignore firmware building errors of UBNT and CyberTAN devicesChuanhong Guo2016-10-262-13/+14
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ar71xx: add support for TP-Link WR802N v1Julius Schulz-Zander2016-10-2612-0/+132
| | | | | | | This patch adds support solely for version 1 of the TP-Link WR802N. It is based on Rick Pannen's patch posted on the OpenWrt devel list. Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
* ar71xx: Remove switch config for the MR12/MR16Chris Blake2016-10-261-2/+0
| | | | | | | These boards do not have a switch, so they should have never been added to this file in the first place. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: add mac partition to the MR12/MR16Chris Blake2016-10-263-23/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space after u-boot-env is used to store the boards Mac address. Sadly as this was removed on any device already on OpenWRT/LEDE, moving forward a new, 64k partition named "mac" will be used to store the mac address for the device (which is the minimum size). This allows users to properly set the correct MAC, without editing the ART partition (which holds the same MAC for all devices). The reason the space is taken from kernel instead of rootfs is currently kernels are only 1.3MB, so that way we can leave the current rootfs space alone for users who fully utilize the available storage space. Once this partition is added to a device, you can set your MAC doing the following: mtd erase mac echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5 sync && reboot Where 00:18:0a:33:44:55 is your MAC address. This was tested, and confirmed working on both the MR12 and MR16. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 21:58:40 +0000