aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx/lzma-loader: fix O32 ABI conformanceGabor Juhos2016-01-171-0/+3
| | | | | | | | | | | | | | | | | | | | | | According to the calling convention of the o32 ABI the caller function must reserve stack space for $a0-$a3 registers in case the callee needs to save its arguments. The assembly code of the loader does not reserve stack space for these registers thus when the 'loader_main' function needs to save its arguments, those will be stored in the 'workspace' area instead of the stack. Because the workspace area is also used by other part of the code, the saved register values gets overwritten and this often leads to failed kernel boots. Fix the code to reserve stack space for the registers to avoid this error. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 48279
* ar71xx: Use full 128MB flash on Netgear WNDR4300 and WNDR3700v4Felix Fietkau2016-01-171-1/+1
| | | | | | | | | | Change MTD on WNDR4300 and WNDR3700v4 to fully utilize the 128MB flash. Credit to @Tuochenlyu on GitHub. Signed-off-by: Chris Marchesi <chrism@vancluevertech.com> SVN-Revision: 48276
* ar71xx: fix ethernet MAC reset on DMA hangFelix Fietkau2016-01-131-38/+55
| | | | | | | | | Fully reset the chip like on a full up/down, but without the PHY statemachine restart. Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48228
* ar71xx: extend ethernet DMA stuck check to all ar724x (and newer) chipsFelix Fietkau2016-01-131-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48227
* kernel/4.1: update to version 4.1.15Hauke Mehrtens2016-01-121-8/+8
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48223
* ar71xx: fix ap152 supportFelix Fietkau2016-01-103-1/+2
| | | | | | | | | | - ethernet gigabit pll - switch configuration - sysupgrade Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 48187
* kernel: move at803x phy patch to genericFelix Fietkau2016-01-031-180/+0
| | | | | | Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 48108
* ar71xx: ensure that LOADADDR is passed to lzma-loaderFelix Fietkau2016-01-031-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48101
* ar71xx: fix factory images for WNR2200 (#19807)Felix Fietkau2016-01-031-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48085
* ar71xx: another fix to wndr3700_board_detectFelix Fietkau2016-01-031-1/+1
| | | | | | | | | | | | | | | | | | My last bugfix (r47538) introduced a new bug in wndr3700_board_detect (again...). Assigning the result of ar71xx_get_mtd_offset_size_format to the model variable before stripping of garbage using awk will cause all NUL bytes to be removed before awk is applied, leading to model strings like "NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to terminate the string. Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk directly. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 48075
* V2 ar71xx : Add Support for the Bitmain Antrouter R1John Crispin2016-01-0112-1/+144
| | | | | | | | | | This patch adds support for the Bitmain Antrouter R1 http://wiki.openwrt.org/toh/bitmain/r1 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 48058
* ar71xx: fix sysupgrade for wnr2200Felix Fietkau2015-12-231-1/+8
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48005
* ar71xx: Update preinit script for new ath10k firmwareJohn Crispin2015-12-231-1/+1
| | | | | | Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 47985
* ar71xx: refresh patchesJohn Crispin2015-12-237-19/+19
| | | | | | Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 47983
* ar71xx: add support for QCA956x ethernetJohn Crispin2015-12-231-0/+166
| | | | | | Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 47982
* ar71xx: update QCA956x supportJohn Crispin2015-12-232-46/+92
| | | | | | | | | | | - separate qca956x and tp9343 (they use different IDs) - rename qca9561->qca956x for consistency - add missing bits (device reset, gpio output select) - fix wmac setup Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 47981
* ar71xx: Add support for AirTight Networks C-55John Crispin2015-12-2314-1/+198
| | | | | | | | This patch is to add support for the AirTight Networks C-55 Access Point Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47973
* ar8216: rework/fix AR8337 MAC swap handlingFelix Fietkau2015-12-205-5/+0
| | | | | | | | | | | | | | In r45970 the MAC swap handling was made opt-in, however some boards have been forgotten during the conversion. Since the reference design uses this MAC swapping, and pretty much all known boards using this chip seem to do so too, enabling the swapping is a more reasonable default than leaving it disabled. Change the code to still allow boards to opt-out of this. Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47956
* ar71xx: Add ath79_register_m25p80_large to support >16MB SPI chipsFelix Fietkau2015-12-192-0/+9
| | | | | | | | | | The following patch is to add ath79_register_m25p80_large, which sets is_flash to false to support bit banging. This is needed on some 32MB+ SPI chips, such as the S25FL256S1 Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47952
* ar71xx: scan nand ubi partition for ath9k eeprom filesFelix Fietkau2015-12-191-0/+21
| | | | | | | | | | The MR18 stores the ath9k eeprom values on the NAND. This patch makes it possible to retrieve the images from there. Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47948
* ar71xx: refactor 10-ath9k-eepromFelix Fietkau2015-12-191-6/+6
| | | | | | | | | move all library includes and 'firmware already exists' check to the top of the script. Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47947
* ar71xx: PowerCloud CR5000 openwrt configurationFelix Fietkau2015-12-195-1/+18
| | | | | | | | | | | | OpenWrt configuration part of support for the PowerCloud Systems CR5000. The CR5000 is a dual-band 802.11n wireless router with 8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and five port gigabit ethernet switch. The CR5000 was sold as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47946
* ar71xx: PowerCloud CR3000 OpenWrt configurationFelix Fietkau2015-12-195-1/+23
| | | | | | | | | | | | OpenWRt configuration part of support for the PowerCloud Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast ethernet wan port that was sold by PowerCloud Systems as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47945
* ar71xx: PowerCloud CAP324 OpenWrt configurationFelix Fietkau2015-12-195-0/+17
| | | | | | | | | | | | | | | Openwrt configuration part of support for PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems who's stock firmware (CloudCommand) provides 'cloud' based managment of large numbers access points. The CAP324 is a dual-band 802.11n wireless access point with 16MB flash and 128MB RAM and single gigabit ethernet port. It can be powered via PoE or a wall wart. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47944
* ar71xx: Image generation for PowerCloud CR5000 Cloud RouterFelix Fietkau2015-12-192-0/+36
| | | | | | | | | | | | Kernel part of support for the PowerCloud Systems CR5000. The CR5000 is a dual-band 802.11n wireless router with 8MB flash, 64 MB RAM, (unused in stock firmware) USB 2.0 port, and five port gigabit ethernet switch. The CR5000 was sold as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47943
* ar71xx: Image generation for PowerCloud CR3000 Cloud RouterFelix Fietkau2015-12-192-2/+36
| | | | | | | | | | | | Image generation part of support for PowerCloud CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM, a four port fast ethernet switch, and a fast ethernet wan port which was sold by PowerCloud Systems as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47942
* ar71xx: PowerCloud CAP324 image generationFelix Fietkau2015-12-192-0/+38
| | | | | | | | | | | | | | | Image generation (and mtd partition) part of support for PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems who's stock firmware (CloudCommand) provides 'cloud' based managment of large numbers of access points. The CAP324 is a dual-band 802.11n wireless access point with 16MB flash and 128MB RAM and single gigabit ethernet port. It can be powered via PoE or a power adaptor. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47941
* ar71xx: Kernel board definition for PowerCloud CR5000Felix Fietkau2015-12-197-0/+192
| | | | | | | | | | | | Kernel part of support for the PowerCloud Systems CR5000. The CR5000 is a dual-band 802.11n wireless router with 8MB flash, 64 MB RAM, (unused in stock firmware) USB 2.0 port, and five port gigabit ethernet switch. The CR5000 was sold as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47940
* ar71xx: Kernel board definition for PowerCloud CR3000Felix Fietkau2015-12-197-0/+176
| | | | | | | | | | | | Kernel part of support for PowerCloud CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM, a four port fast ethernet switch, and a fast ethernet wan port which was sold by PowerCloud Systems as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47939
* ar71xx: Kernel board definition for PowerCloud CAP324Felix Fietkau2015-12-197-0/+148
| | | | | | | | | | | | | | | Kernel part of support for PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for the CloudCommand service for 'cloud' based managment of large numbers access points. The CAP324 is a dual-band 802.11n wireless access point with 16MB flash and 128MB RAM and single gigabit ethernet port. It can be powered via PoE or a power adaptor. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47938
* ar71xx: add support for TRENDnet TEW-823DRUJohn Crispin2015-12-1713-3/+221
| | | | | | | | | | | | | | Add support for TRENDnet TEW-823DRU: - cpu: QCA9558 @720MHz - flash: 16MB - ram: 256MB - 4+1 RJ45 100/1000Mbps - wifi: QCA9558 (bgn) and QCA9880-BR4A (ac) - 1x USB 2.0 Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 47927
* ar71xx: clean up ethernet tx queue after reset, wake queues when done - ↵Felix Fietkau2015-12-141-3/+8
| | | | | | | | fixes hangs reported in #18922 Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47892
* ar71xx: Update merakinand.sh to fix sysupgradeFelix Fietkau2015-12-131-1/+0
| | | | | | | | | | Remove reliance on /lib/upgrade/nand.sh as this is called by sysupgrade, based on felix's comments at https://lists.openwrt.org/pipermail/openwrt-devel/2015-December/037963.html Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47889
* ar71xx: add rx/tx delay definitons for qca955x's MACFelix Fietkau2015-12-121-0/+14
| | | | | | | | This patch adds the rx/tx register offsets for the qca955x SoC. Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47882
* ar71xx: add support for Cisco's MR18John Crispin2015-12-1216-0/+541
| | | | | | | | | | | This patch adds support for Cisco's MR18. Detailed instructions for the flashing the device can be found in the OpenWrt forum thread: <https://forum.openwrt.org/viewtopic.php?id=59248> Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47878
* ar71xx: reorganize target patches/files to make it possible to add boards ↵Felix Fietkau2015-12-1123-2314/+1843
| | | | | | | | without adding patch files Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47874
* ar71xx: on wnr2200, revert the mac0/mac1, the ethernet interfaces are ↵Felix Fietkau2015-12-111-3/+3
| | | | | | | | swapped. use MAC1 for wlan Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47873
* ar71xx: fix MAC address swapping on WNR2200 and fix the WLAN MAC addressFelix Fietkau2015-12-111-3/+4
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47871
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-113-3/+3
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
* ar71xx: build image for TL-WR710N v2.1John Crispin2015-12-111-1/+10
| | | | | | | | | | This patch just extends target/linux/ar71xx/image/Makefile to build images also for version 2.1 of TL-WR710N patch against the latest git Signed off by: Norbert Wegener <nw@wegener-net.de> SVN-Revision: 47849
* ar71xx: add LED driver NU801John Crispin2015-12-114-0/+476
| | | | | | | | | The MR18 uses a 3-channel 16-bit PWM Constant Current Driver for its status LED. Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47848
* ar71xx: Add support for Wallys DR344John Crispin2015-12-119-0/+254
| | | | | | | | This patch is for Wallys DR344 support under OpenWRT Signed-off-by: Philippe Duchein <wireless-dev@duchein.net> SVN-Revision: 47847
* ar71xx: image for AP121/16MJohn Crispin2015-12-111-1/+3
| | | | | | | | Build image for the AP121 reference board with 16MB flash. Signed-off-by: Norbert Wegener <nw@wegener-net.de> SVN-Revision: 47846
* ar71xx: fix switch port mapping for tl-wdr4300/3600Felix Fietkau2015-12-061-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47799
* ar71xx: convert gpio switch config to board.dJo-Philipp Wich2015-12-042-25/+27
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47763
* all: remove redundant board.d/00_model filesJo-Philipp Wich2015-12-041-13/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47753
* all: remove dummy ucidef_set_interface_loopback() from board.dJo-Philipp Wich2015-12-031-2/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47744
* ar71xx: board.d: add missing include (#21296)Jo-Philipp Wich2015-12-031-0/+1
| | | | | | | | | Include /lib/functions/system.sh in 02_network to define missing mtd_get_mac_binary() procedure. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47723
* board.d: remove redundant ucidef_set_interfaces_lan_wan() callsJo-Philipp Wich2015-12-031-21/+0
| | | | | | | | | | This removes calls to ucidef_set_interfaces_lan_wan() and ucidef_set_interfaces_lan() on boards where all relevant info can be inferred from the switch definition. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47722
* board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()Jo-Philipp Wich2015-12-031-87/+44
| | | | | | | | | | | | This changes uci-defaults-new.sh, config_generate and all relevant board.d files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into a single function. Also removes now superfluous enable and reset arguments. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47721
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 14:45:59 +0000