aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: add support for the MikroTik RB911-2Hn/5Hn boardsGabor Juhos2018-01-2211-3/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the MikroTik RB911-2Hn (911 Lite2) and the RB911-5Hn (911 Lite5) boards: https://mikrotik.com/product/RB911-2Hn https://mikrotik.com/product/RB911-5Hn The two boards are using the same hardware design, the only difference between the two is the supported wireless band. Specifications: * SoC: Atheros AR9344 (600MHz) * RAM: 64MiB * Storage: 16 MiB SPI NOR flash * Ethernet: 1x100M (Passive PoE in) * Wireless: AR9344 built-in wireless MAC, single chain 802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn) Notes: * Older versions of these boards might be equipped with a NAND flash chip instead of the SPI NOR device. Those boards are not supported (yet). * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the same hardware. Support for that can be added later with little effort probably. Installation: 1. Setup a DHCP/BOOTP Server with the following parameters: * DHCP-Option 66 (TFTP server name): pointing to a local TFTP server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename of the to be booted image. The usable intramfs files are: - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin 2. Press the reset button on the board and keep that pressed. 3. Connect the board to your local network via its ethernet port. 4. Release the button after the LEDs on the board are turned off. Now the board should load and start the initramfs image from the TFTP server. 5. Upload the sysupgrade image to the board with scp: $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin 5. Log in to the running system listening on 192.168.1.1 via ssh as root (without password): $ ssh root@192.168.1.1 7. Flash the uploaded firmware file from the ssh session via the sysupgrade command: root@OpenWrt:~# sysupgrade /tmp/fw.bin Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: make leds-gpio usable with single-ended GPIOsGabor Juhos2018-01-222-0/+90
| | | | | | | | | Add patches for the leds-gpio driver to make it usable with open-drain and open-source kind of GPIO lines. This type of functionality is required by various MikroTik boards. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: mach-rbspi: return rb_info from rbspi_platform_setupGabor Juhos2018-01-221-13/+13
| | | | | | | | | | | | Modify the rbspi_platform_setup() function to return the pointer of the rb_info structure. This allows board specific setup routines to access the various fields of the information. It is useful for investigating the hardware option bits for example. Also update the board setup codes, to ensure that those handle the new return value correctly. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: add definitions for RouterBOARD hardware option bitsGabor Juhos2018-01-221-0/+26
| | | | | | | | | | | | Add bit definitions for the 'hardware options' tag which is used in the MikroTik devices' hardware configurations. These values can be used in board setup codes, to do different initialization sequences. The values were obtained from the RouterOS 6.41-rc38 patches. Additionally, introduce two helper functions what make the processing of the hardware options easy. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* kernel: bump 4.4 to 4.4.112Kevin Darbyshire-Bryant2018-01-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: target/linux/generic/patches-4.4/030-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch target/linux/generic/patches-4.4/030-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch target/linux/generic/patches-4.4/030-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch target/linux/generic/patches-4.4/030-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch CVEs completely or partially addressed: CVE-2017-5715 CVE-2017-5753 CVE-2017-17741 CVE-2017-1000410 Compile-tested: ar71xx Archer C7 v2 Run-tested: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ar71xx: drop mdio-gpio.h include from mach-om5pacv2.cGabor Juhos2018-01-171-6/+0
| | | | | | | | | | | | | | The setup code of the OpenMesh OM5P ACv2 device uses nothing from the mdio-gpio.h header, so remove the inclusion of that. Also remove the kernel version check which is needed only because the mdio-gpio.h header exists in a different path in older kernels. Compile tested only. Cc: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix format of the 701-MIPS-ath79-add-routerboard-detection patchesGabor Juhos2018-01-172-2/+2
| | | | | | | | | | | | Commit e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff format, the unchanged, contextual lines must be preceded by a space character. Refresh the patches with quilt to fix them. Fixes: e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix format of the 741-MIPS-ath79-add-PCI-for-QCA9556-SoC patchesGabor Juhos2018-01-172-12/+12
| | | | | | | | | | | The patches introduced in commit 20e68f6d395d ("ar71xx: kernel: enable PCI on QCA9556 SoC") have non standard format. In unified diff format, the unchanged, contextual lines must be preceded by a space character. Refresh the patches with quilt to fix them. Fixes: 20e68f6d395d ("ar71xx: kernel: enable PCI on QCA9556 SoC") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: mach-rbspi: simplify reset button registrationGabor Juhos2018-01-171-64/+30
| | | | | | | | | | | | The setup code defines four individual structures for the Reset buttons of the supported boards. The only difference between the definitions is the GPIO number used for the button. Replace the different structures with one generic variant, and add a helper function to simplify the button registration. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix TP-Link Archer C7 v4 switch LEDsDavid Bauer2018-01-151-8/+12
| | | | | | | | Match mapping of the switch LEDs according to the TP-Link firmware behavior. LAN port 1 triggers the most right LAN LED, LAN port 2 the second LAN LED from the right and so on. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: image: rework EnGenius ENS202EXT factory imagePiotr Dymacz2018-01-151-7/+4
| | | | | | | | | Current EnGenius ENS202EXT factory image recipe version causes factory images of the following devices to be corrupted. This issue wasn't visible until recent changes of image Makefile snippets order. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)Roger Pueyo Centelles2018-01-159-10/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info. Specifications: - SoC: Qualcomm Atheros QCA9556 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive PoE in Working: - Board/system detection - Sysupgrade - Serial console - Ethernet - 2.4 GHz radio - 5 GHz radio - Reset button Not working: - LEDs (added according to Mikrotik's GPL sources but not functional) Unsupported: - ZT2046Q SPI temperature and voltage sensor Contributors: Giuseppe Tipaldi (@Ciusss89) Ricky (@rickydee) Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
* ar71xx: kernel: enable PCI on QCA9556 SoCRoger Pueyo Centelles2018-01-152-0/+24
| | | | | | | | | This patch enables the PCI bus on the QCA9556 SoC, the same way it is done on the same family SoC QCA9558. Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: add support for GL.iNet GL-AR750Piotr Dymacz2018-01-1515-10/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3x 10/100 Mbps Ethernet - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 1x USB 2.0 (power controlled by GPIO) - 1x microSD (GL857L) - 3x LED (all driven by GPIO) - 1x button (reset) - 1x 2-pos switch - header for optional PoE module - 1x micro USB for main power input - UART + I2C header on PCB Flash instruction: Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used to flash OpenWrt/LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: move Sitecom WLR-8100 from legacy to genericPiotr Dymacz2018-01-153-9/+10
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix Sitecom WLR-8100 supportDavide Fioravanti2018-01-156-14/+17
| | | | | | | | | | | | | | This patch fixes Sitecom WLR-8100: - mtd layout - LAN and WAN MAC address setup - 2.4 GHz Wi-Fi MAC address setup - 5 GHz Wi-Fi support (calibration data, MAC address setup, missing ath10k-* packages) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [squashed commits, fixed whitespace issues, reworded commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network R36APiotr Dymacz2018-01-1512-1/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36A is a successor of the previous model, the R36 (Ralink RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB - 1x USB 2.0 (power controlled by GPIO) - 6x LED (5 of them are driven by GPIO) - 2x button (reset, wifi/wps) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Teltonika RUT900Piotr Dymacz2018-01-1513-0/+267
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is an industrial 3G router based on Atheros AR9344. There are available 3 other models in RUT9xx series: RUT905, RUT950 and RUT955, which differ in availability of additional I/O ports, built-in GSM modem type, GPS antenna and other features. FCC ID of the RUT950 model (LTE module built-in): 2AET4-RUT950. This patch adds support for the RUT900 model only but can be easily extended to cover whole series. Also, as there are several different 3/4G modules (Huawei, Quectel, Telit) used in whole series, packages required for WWAN support are not included by default. It is up to the user to install required software for built-in modem. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA - built-in 3G module (example: Telit HE910-D) - 2x miniSIM slot - 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G) - PCA9539 16-bit GPIO I2C expander - 12x LED (4 are driven by AR9344, 7 by PCA9539) - 1x button (reset) - DC jack for main power input (9-30 V) - UART available on PCB edge connector Serial console pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network N5QPiotr Dymacz2018-01-1412-2/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network N5Q is a successor of previous model, the N5 (outdoor CPE/AP, based on Atheros AR7240 + AR9280). New version is based on Atheros AR9344. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm - 8x LED (7 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmare which is based on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP91-5GPiotr Dymacz2018-01-1413-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros AR7240 + AR9280. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 32 MB of RAM (DDR1) - 8 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm - 6x LED (5 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART and LEDs headers on PCB Flash instruction: Use "factory" image in vendor GUI (in case of problems, make sure your board has up to date firmware). Alternatively, TFTP in U-Boot can be used: select option "2. Load system code then write to Flash via TFTP" during early boot and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: cosmetic cleanups in preinit scriptsPiotr Dymacz2018-01-143-94/+83
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: drop LED control from 05_set_iface_mac_ar71xxPiotr Dymacz2018-01-141-1/+0
| | | | | | There is no "dir-615-c1:green:wancpu" LED defined in mach-dir-615-c1.c Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: fix boards order in 05_set_preinit_iface_ar71xxPiotr Dymacz2018-01-141-3/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: create new ar71xx/tiny subtarget for 4MB flash devicesMatthias Schiffer2018-01-1313-1007/+1076
| | | | | | | | | | | This new subtarget sets the small_flash flag and removes unused kernel configuration. small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default configuration; removing unneeded hardware support from ar71xx/tiny saves another ~18KB (both after LZMA). Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx/generic: add generic- prefix to vendor-specific image Makefile snippetsMatthias Schiffer2018-01-135-4/+4
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: reorganize kernel configurationMatthias Schiffer2018-01-135-898/+728
| | | | | | | | | | Rather than including all machines for the generic subtarget in the base configuration, leave the base configuration without specific machines and create a proper subtarget config for ar71xx/generic. The configuration diffs of the mikrotik and nand subtargets get significantly shorter, as will the configurations of future subtargets. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: disable devicetree supportMatthias Schiffer2018-01-135-25/+75
| | | | | | | | | | | | While we'd like to convert ar71xx to DT-based configuration eventually, we aren't quite there yet, and shipping half-baked DT support that is not used at all wastes precious space. Saves ~120KB before LZMA, ~33KB after LZMA. Run-tested on TP-Link CPE510 and TL-WR841 v7. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: bump 4.4 to 4.4.110Kevin Darbyshire-Bryant2018-01-101-1/+1
| | | | | | | | | | Refresh patches Fixes: CVE-2017-5754 aka Meltdown Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [fix typo in commit msg, conflict after 4.14 bump] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.9 to 4.9.75Kevin Darbyshire-Bryant2018-01-101-2/+2
| | | | | | | | | | | | | Refresh patches Fixes: CVE-2017-5754 aka Meltdown Tested-on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [fix conflict after 4.14 bump] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: fix Archer C7v4 5GHz MAC-addressDavid Bauer2018-01-091-1/+4
| | | | | | | | | | | The TP-Link firmware uses (primary_mac-1) as MAC-address for the 5GHz WiFi. This applies the same behaviour to LEDE. Currently, the MAC-address is retrieved from eth1, which does not exist on the Archer C7 v4. As a result from this, every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: remove obsolete '< KERNEL_VERSION(4, 4, 0)' checkGabor Juhos2018-01-091-5/+0
| | | | | | | | | Because the oldest supported kernel version on the ar71xx target is 4.4, the condition that the kernel version is smaller than 4.4.0 is always false. Remove the obsolete check from mach-rb4xx.c to clean up the code a bit. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: remove obsolete '< KERNEL_VERSION(4, 2, 0)' checkGabor Juhos2018-01-091-7/+0
| | | | | | | | | Because the oldest supported kernel version on the ar71xx target is 4.4, the condition that the kernel version is smaller than 4.2.0 is always false. Remove the obsolete check from ag71xx_main.c to clean up the code a bit. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: remove obsolete '< KERNEL_VERSION(3, 15, 0)' checksGabor Juhos2018-01-092-17/+0
| | | | | | | | | Because the oldest supported kernel version on the ar71xx target is 4.4, the condition that the kernel version is smaller than 3.15.0 is always false. Remove the obsolete checks from the target specific source files to clean up the code a bit. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx/mikrotik: disable TP-Link TL-WR810N v2 board supportGabor Juhos2018-01-091-0/+1
| | | | | | It does not belongs to the MikroTik boards. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx/mikrotik: disable unused MTD partitioning and split driversGabor Juhos2018-01-091-0/+6
| | | | | | Reduces the compressed kernel size by ~2.5KB. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx/mikrotik: disable unused ethernet switch and phy driversGabor Juhos2018-01-091-0/+4
| | | | | | | | | | | | | | | | | | | | Disable the drivers for the following ethernet switches: Realtek RTL8306 Realtek RTL8366/8367 Marvell 88E6060 (DSA) Marvell 88E6063 (DSA) Also disable the phy driver for Marvell PHYs. None of the supported RouterBOARDs are using any device which needs these drivers. Disable the DSA framework too, because it is not required by the remaining switch drivers. This reduces the compressed kernel size by ~20KB. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix Kconfig dependency of the 88E6063 switch DSA driverGabor Juhos2018-01-092-2/+4
| | | | | | | | | | | | The Marvell 88E6063 ethernet switch driver depends on the DSA framework. Add a 'depends on NET_DSA' statement to its Kconfig entry to state that explicitly. Fixes the following Kconfig warning: warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA) Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: sort kernel configurationsGabor Juhos2018-01-094-6/+6
| | | | | | | The symbols in some kernel configurations of the target are in wrong order. Sort them with kconfig.pl. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix compiler warnings in mdio-bitbang.c for 4.4Gabor Juhos2018-01-072-3/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Building Linux 4.4 for ar71xx throws the following warnings in drivers/net/phy/mdio-bitbang.c: CC drivers/net/phy/mdio-bitbang.o In file included from include/linux/irqflags.h:14:0, from drivers/net/phy/mdio-bitbang.c:20: drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_read': include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast (void)(&__dummy == &__dummy2); \ ^ include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck' typecheck(unsigned long, flags); \ ^ include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save' raw_local_irq_save(flags); \ ^ drivers/net/phy/mdio-bitbang.c:162:2: note: in expansion of macro 'local_irq_save' local_irq_save(flags); ^ include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast (void)(&__dummy == &__dummy2); \ ^ include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck' typecheck(unsigned long, flags); \ ^ include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore' #define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0) ^ drivers/net/phy/mdio-bitbang.c:175:2: note: in expansion of macro 'local_irq_restore' local_irq_restore(flags); ^ drivers/net/phy/mdio-bitbang.c:159:11: warning: unused variable 'i' [-Wunused-variable] int ret, i; ^ In file included from include/linux/irqflags.h:14:0, from drivers/net/phy/mdio-bitbang.c:20: drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_write': include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast (void)(&__dummy == &__dummy2); \ ^ include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck' typecheck(unsigned long, flags); \ ^ include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save' raw_local_irq_save(flags); \ ^ drivers/net/phy/mdio-bitbang.c:185:2: note: in expansion of macro 'local_irq_save' local_irq_save(flags); ^ include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast (void)(&__dummy == &__dummy2); \ ^ include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck' typecheck(unsigned long, flags); \ ^ include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore' #define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0) ^ drivers/net/phy/mdio-bitbang.c:200:2: note: in expansion of macro 'local_irq_restore' local_irq_restore(flags); ^ These are caused by the 900-mdio_bitbang_ignore_ta_value and 901-phy-mdio-bitbang-prevent-rescheduling-during-command patches. The first patch removes some code but it does not remove the variable which is used by the removed code only. The second patch adds local_irq_{save,restore} calls. The type of the argument of these calls must be 'unsigned long', but the patch defines the variable as 'long'. Fix both patches to silence the warnings. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ag71xx: Fix rx ring buffer stall on small packets flood on qca956x and qca953x.Vittorio Gambaletta2017-12-293-1/+22
| | | | | | Backported from Code Aurora QSDK Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
* ar71xx: spi-rb4xx: balance clk_prepare_enable() callGabor Juhos2017-12-241-2/+2
| | | | | | | | | | | | | Commit c312cef223dd ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call with clk_prepare_enable() to meet the common clock framework requirements. However it did not change the clk_disable() call in the error patch which thus leads to imbalance. Fix the code by using the correct counterpart of clk_prepare_enable() in both places. Fixes: c312cef223dd ("ar71xx: spi-rb4xx fix.") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)Roger Pueyo Centelles2017-12-216-3/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac wireless router. Additionally, it adds a new profile for devices with >= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget. See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info. Specifications: - SoC: Qualcomm Atheros QCA9558 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9822 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in - SFP: 1x host Working: - Board/system detection - NAND storage detection - Wireless - Ethernet - 1x user LED - Reset button - Sysupgrade Untested: - SFP cage (probably not working) Installation: - Boot initramfs image via TFTP and then flash sysupgrade image Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: fix spelling in mach-rb922.cRoger Pueyo Centelles2017-12-211-1/+1
| | | | Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: fix rb922gs_nand_scan_fixup()Roger Pueyo Centelles2017-12-211-1/+5
| | | | | | | | | Apply code from commits 9e1bc27e6d67fa29791eb0fac5e5f0066d12a761 (ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and 665bb2749906aff4d4ec607a308353fa30cb1b3a (ar71xx: fix invalid pointer dereference in rb95x_nand_scan_fixup()) to RB92x devices too. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* kernel: Update kernel 4.9 to 4.9.70Hauke Mehrtens2017-12-193-3/+3
| | | | | | Runtime tested on lantiq. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: fix lan ports on ens202extMarty E. Plummer2017-12-181-0/+1
| | | | | | | | | In the stock firmware both eth0 and eth1 are set to br-lan, add this behavior to our images. Fixes: FS#1084 Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
* ar71xx: fix invalid pointer dereference in rb95x_nand_scan_fixup()Gabor Juhos2017-12-161-0/+4
| | | | | | | | | | | | Since Linux 4.6, mtd->priv no longer points to the NAND specific structure. Under 4.9 it contains NULL, thus using it to access chip->options causes an invalid pointer dereference (FS#1200). Update the code to use the mtd_to_nand() helper under 4.9 to obtain the address of the chip specific data. Fixes: 7bbf4117c6fe ("ar71xx: Add kernel 4.9 support") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix invalid pointer dereference in c60_nand_scan_fixup()Gabor Juhos2017-12-151-0/+4
| | | | | | | | | | | | | | | | Since Linux 4.6, mtd->priv no longer points to the NAND specific structure. Under 4.9 it contains NULL, thus using it to access the fields of the nand_chip structure causes an invalid pointer dereference. Update the code to use the mtd_to_nand() helper under 4.9 to obtain the address of the chip specific data. Compile tested only. Fixes: 7bbf4117c6fe ("ar71xx: Add kernel 4.9 support") Signed-off-by: Gabor Juhos <juhosg@freemail.hu> Tested-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: fix LED name typo for GL-AR300Mkyson Lok2017-12-151-1/+1
| | | | | | It shouldn't use double colon characters. Signed-off-by: kyson Lok <kysonlok@gmail.com>
* Revert "ar71xx: TL-WR1043N v4/v5: add orange WAN LED support"John Crispin2017-12-141-19/+3
| | | | | | | | | | This reverts commit 256990cbc0157feb8a9f37efeebf0330ab73727f. this commit caused a compile error "TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined. Signed-off-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-28 14:11:12 +0000