aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: remove wrong MAC address adjustment for Archer C60 v2Adrian Schmutzler2020-03-111-2/+1
| | | | | | | | | | | The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac is broken since a "mac" partition is not set up for this device on ar71xx. Instead, the MAC address is already patched correctly in 11-ath10k-caldata. Remove the useless adjustment. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2Adrian Schmutzler2020-03-112-5/+5
| | | | | | | | | | | | | | | | | | | The MAC addresses for lan/wan are swapped compared to the vendor firmware. This adjusts to vendor configuration, which is: lan *:7b label wan *:7c label+1 2.4g *:7b label 5g *:7a label-1 Only one address is stored in <&mac 0x8>, corresponding to the label. This has been checked on revisions v1, v2 and v3. Since ar71xx calculates the ath10k MAC address based on the ethernet addresses, the number there is adjusted, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx/ath79: ew-dorin, fix the trigger level for WPS buttonCatrinel Catrinescu2020-03-111-1/+1
| | | | | | | | | Because the WPS button had the wrong trigger level, the failsafe mode was triggered quite often, after this commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=27f3f493de Signed-off-by: Catrinel Catrinescu <cc@80211.de>
* ar71xx: add missing LED migration for Archer C7David Bauer2020-03-011-0/+3
| | | | | | | | | | | | When changing the LED names for the Archer C7 to represent the correct color, a migration for existing UCI entries was not created. Add a migration to keep existing LED configurations working. Fixes commit c79c001b593b ("ar71xx: Archer C7 v1 LED names and RFKILL fixes") Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: correct AVM FRITZ Repeater 450E WPS button flagDavid Bauer2020-03-011-1/+1
| | | | | | | | | The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low. Correct the active low flag to avoid unintenional activation of failsafe mode on boot. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.171Koen Vandeputte2020-02-244-4/+4
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2013-1798 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.167Koen Vandeputte2020-01-243-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: change u-boot-env to read-write for gl-ar150/-domino/mifiKimmo Vuorinen2020-01-231-3/+3
| | | | | | | | | Change u-boot-env partitions to be mounted as read-write for gl-ar150, gl-domino and gl-mifi so uboot-envtools support is possible. Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: use dynamic partitioning for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-221-1/+1
| | | | | | | This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and will allow to use this for ath79 as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: ubnt-rocket-m-ti: fix RSSI LED definitionsLech Perczak2020-01-212-6/+8
| | | | | | | | | | | | | | | | When mapping for RSSI LEDs was defined for interface wlan0 on Ubiquiti Rocket M Titanium, it missed connection to actual interface. Therefore create the mapping to interface, so RSSI LEDs work without additional configuration, after starting rssileds service. While at that, split RSSI into ~equal intervals for 6 LEDs, and remove coefficients needed for PWM LEDs, as this board does not support PWM LEDs. Finally, for complete support, enable 'rssileds' package in per-device rootfs, so the indicator works out of box. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* kernel: bump 4.14 to 4.14.164Koen Vandeputte2020-01-202-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx/mikrotik: use ath10k-ct-smallbuffers for 64 MiB devicesThomas Nixon2020-01-151-1/+1
| | | | | | | | | | This image is only needed on one device (wAP AC); since this target is going to be removed anyway it doesn't make sense to add an extra "low RAM" image. Fixes OOM issues on RouterBoard wAP AC. Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* ar71xx: Remove mtd cfi_cmdset_0002 status check patchTokunori Ikegami2020-01-051-62/+0
| | | | | | | | | | | | | Currently the patch only changes break to use goto statement instead. But not necessary acutually since the ret value checked after the for loop. So it is okay for the break case before changed by the patch also. This patch only reverts the following commit partially. https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e77619eaa7 Note: The changes are mainly applied into the linux kernel upstream. Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com> Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.162Hauke Mehrtens2020-01-051-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ramips Runtime-tested on: ramips Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.159Koen Vandeputte2019-12-241-1/+1
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 302-0002-dmaengine-dw-implement-per-channel-protection-contro.patch Fixes: - CVE-2019-19332 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix MAC address setup for TL-WDR4300 boardSungbo Eo2019-12-212-1/+5
| | | | | | | | | | | | | | | | | The current ethernet MAC address setup of TL-WDR4300 board is different from the setup of stock firmware: OpenWrt: lan = label_mac -2, wan = label_mac -2 stock: lan = label_mac, wan = label_mac +1 This patch applies to all devices using TL-WDR4300 board: TL-WDR3600 v1 TL-WDR4300 v1 TL-WDR4300 v1 (IL) TL-WDR4310 v1 Mercury MW4530R v1 Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ar71xx: indicate upgrade using system LEDDavid Bauer2019-12-161-0/+3
| | | | | | | | | This enables the system LED to indicate a running firmware upgrade. This pattern is used on most platforms provided by the generic base-files package. ar71xx uses it's own implementation for the system-LED, where the upgrade case is not yet implemented. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.158Koen Vandeputte2019-12-101-1/+1
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 400-mtd-add-rootfs-split-support.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ubnt-(xm,xw): add rssileds packageLech Perczak2019-11-211-2/+8
| | | | | | | | | | | | | | | | | | In order to make RSSI indicator on the device work out of box, include "rssileds" package in per-device rootfs image by default for Ubiquiti XM and XW devices, namely: - Bullet M (XM/XW) - Rocket M (XM/XW) - Nanostation M (XM/XW) - Nanostation Loco-M (XW) This moves the package addition to the individual devices in order to prevent accidental inclusions of the package when not looking at the parent node carefully enough. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [add bullet-m-xw, remove rocket-m-ti, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix buttons for TP-Link TL-WDR4900 v2Adrian Schmutzler2019-11-191-2/+13
| | | | | | | TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so don't set up an RFKILL for this device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix LED setup for TL-WDR4900 v2Adrian Schmutzler2019-11-191-2/+36
| | | | | | | | | | | | | | | | | In ar71xx there is only one combined mach file for Archer C5/C7 and TL-WDR4900 v2. This one uses the same LED struct for all devices, defining "green" LEDs for them. However, WDR4900 uses blue front LEDs, while only C5/C7 uses green ones. Despite, in base-files WDR4900 is actually set up with "blue" for the mentioned LEDs. Thus, this patch creates a separate LED struct for WDR4900, so the LEDs can be set up correctly. Despite, the wlan5g LED is removed as it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7). Note: While front LEDs are blue, USB LEDs (on the back) are green, so colors are mixed intentionally for the WDR4900 v2. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix MAC address setup for TL-WDR4900 v2Adrian Schmutzler2019-11-171-3/+6
| | | | | | | | | | | | The MAC address setup of the TL-WDR4900 v2 is different from the C5/C7. This aligns ar71xx with the setup in ath79: wlan0 (5GHz) : -2 wlan1 (2.4GHz) : -1 eth1 (LAN) : 0 eth0 (WAN) : 1 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2Adrian Schmutzler2019-11-132-3/+2
| | | | | | | | | | | | | | | | | | | As discussed in 1d18a14a90c7 ("ath79: really fix TP-Link Archer C7 v2 MAC address"), stock firmware MAC address assignment is actually as follows: wlan0 (5GHz) : -1 wlan1 (2.4GHz) : 0 eth1 (LAN) : 0 eth0 (WAN) : 1 This has never been fixed for ar71xx, so let's do it now. Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned to basemac-1 before ... Fixes: FS#408 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix tl-wdr3320-v2 upgrade南浦月2019-11-081-1/+1
| | | | | | | | | Fix the error that tl-wdr3320-v2 can't upgrade firmware via web interface by using magic_ver="0200" for this device. Signed-off-by: 南浦月 <nanpuyue@gmail.com> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: fix bug in NBG6716 kernelpacking, add firmware partitionAndré Valentin2019-10-271-2/+3
| | | | | | | -Fix the kernel image generation (more robust) -Add a firmware partition table allowing easy upgrade to ath79 Signed-off-by: André Valentin <avalentin@marcant.net>
* ar71xx: add model detection for UniFi AC-LRAndreas Ziegler2019-10-232-0/+9
| | | | | | | | | | | | | | This commit adds correct model detection for UniFi AC-LR. Previously, said device was incorrectly detected as UniFi-AC-LITE/MESH. The Information about the device is stored at 0xC in the EEPROM partition. It corresponds to the sysid in /etc/board.info of the Ubiquiti stock firmware. Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [adjust naming style of target to existing ones] Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: improve support for TP-Link CPE510 v2Adrian Schmutzler2019-10-217-21/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") where the support for this device wasn't optimal. Device support for the CPE510v2 so far has been a hack to enable flashing with CPE510v1 images. Those even have different hardware (e.g. additional ethernet port). With this patch, we provide proper support for this device in ar71xx. Installation: - Flash factory image through stock firmware WEB UI or through TFTP - To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. - Rename factory image to recovery.bin - Stock TFTP server IP: 192.168.0.100 - Stock device TFTP address: 192.168.0.254 Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net> [Rebased onto revert commit, changed comments in mach-cpe510.c, changed commit title and description, fixed eth0 MAC address, removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: WNDR4300: fix WAN LED behaviourMichal Cieslakiewicz2019-10-211-2/+1
| | | | | | | | | Change WAN LED behaviour to be consistent with other Netgear routers running OpenWrt. Instead of link speed, use amber colour to indicate link status. Green LED should be used when Internet connection is up and running. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx: WNDR4300: use standard labels for buttonsMichal Cieslakiewicz2019-10-211-3/+3
| | | | | | | GPIO key labels have been changed to standard ones (rfkill, reset, wps). It does not affect button functionality. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx: remove unnecessary execute permission bitSungbo Eo2019-10-121-0/+0
| | | | | | .c files do not need to be executable. 644 is enough. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: bump 4.14 to 4.14.147Koen Vandeputte2019-10-082-15/+13
| | | | | | | | | | | | | Refreshed all patches. Altered patches: - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx) - 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79) Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-0613-173/+173
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.145Koen Vandeputte2019-09-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.144Koen Vandeputte2019-09-205-20/+15
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 816-pcie-support-layerscape.patch Fixes: -CVE-2019-15030 Compile-tested on: cns3xxx, layerscape Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix typo in platform_do_upgrade_compex()Rafał Miłecki2019-09-161-1/+1
| | | | | Fixes: 641f6b6c26cb ("treewide: use new procd sysupgrade $UPGRADE_BACKUP variable") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: make IRQ fixes target specificKoen Vandeputte2019-09-141-0/+57
| | | | | | | | | | | | | Move the IRQ fix from generic to ar71xx specific. Other targets like ath79 have specific pathes to delete this code. This resulted in a build failure on ath79 While at it, wipe the 4.19 version, as ar71xx will never reach this. Fixes: 530f76708cef ("ar71xx: Fix potentially missed IRQ handling during dispatch") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix potential IRQ misses during dispatch for qca953xKoen Vandeputte2019-09-131-0/+27
| | | | | | | | | | | If both interrupts are set in the current implementation only the 1st will be handled and the 2nd will be skipped due to the "if else" condition. Fix this by using the same approach as done for QCA955x just below it. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Revert "ar71xx: use platform code for qca955x usb0 init"Koen Vandeputte2019-09-121-14/+0
| | | | | | | | | | | | | | | This reverts commit 5b98061bb1ac7e3affadda7b55c6f4ed4eb8268e. As Piotr Dymacz pointed out: In QCA MIPS based WiSOCs, for first USB interface, device/host mode can be selected _only_ in hardware see description of 57c641ba6e QCA955x and QCA9563, second USB can be switched to device mode in software (tested and confirmed on real hardware). Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: qca955x pci init/reset fixesTomislav Požega2019-09-111-0/+120
| | | | | | | | | | | | | | Current ar724x code does the reset only on single pci bus, and in case of qca9558 writes the wrong register (0x10 vs 0x0c). This change allows the reset of second pci bus, commonly used in Archer C7 devices, in case host controller is stuck in reset. If the resetting controller on boot can solve any other issue it can be enabled unconditionally by removing reset check before ar724x_pci_hw_init is called. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> [refreshed to apply cleanly] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: enable ddr wb flush on qca955xTomislav Požega2019-09-111-0/+49
| | | | | | | | Enable flushing of write buffers on qca955x. GPL code has 0x88 reg defined for PCI flush which is likely an error since the device freezes on boot. So use DS default value 0xA8 for PCI flush. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* ar71xx: use platform code for qca955x usb0 initTomislav Požega2019-09-111-0/+14
| | | | | | | Switch from ci_usb_setup to generic platform initialization of usb0 port. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* treewide: sysupgrade: use $UPGRADE_BACKUP to check for backupRafał Miłecki2019-09-113-4/+4
| | | | | | | Now that $UPGRADE_BACKUP is set conditionally there is no need to check the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-053-4/+4
| | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: fix invalid UPGRADE_OPT_SAVE_CONFIG spellingsRafał Miłecki2019-09-053-4/+4
| | | | | | | That was a result of accidentally running "sed" twice on some files. Fixes: 5797fe84a3b5 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: replace remaining (not working now) $SAVE_CONFIG usesRafał Miłecki2019-09-053-4/+4
| | | | | | | This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG Fixes: b534ba961100 ("base-files: pass "save_config" option to the "sysupgrade" method") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: sysupgrade: accept ath79 combined-imageTomasz Maciej Nowak2019-09-011-1/+1
| | | | | | | | | | There is md5 sum of whole image embedded in combined-image header which is checked on sysupgrade. The check will fail for ath79 images which may have embedded metadata. This is because metadata are appended after the combined image is created. To allow smooth transition from ar71xx to ath79, strip metadata before calculating md5 sum for whole image. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ar71xx: WNR2200: remove redundant GPIO for WLAN LEDMichal Cieslakiewicz2019-08-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | Without this patch, an extra entry appears for AR9287 GPIO that duplicates WLAN LED but in fact drives nothing: gpiochip1: GPIOs 502-511, ath9k-phy0: gpio-502 ( |netgear:blue:wlan ) out hi gpio-503 ( |netgear:amber:test ) out hi gpio-504 ( |netgear:green:power ) out lo gpio-505 ( |rfkill ) in hi gpio-507 ( |wps ) in hi gpio-508 ( |reset ) in hi gpio-510 ( |ath9k-phy0 ) out hi <===! The pin pointed above is default LED GPIO (8) for AR9287. For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN LED instead - but initialization code is missing that information. This fix calls ap9x_pci_setup_wmac_led_pin() function at device setup, forcing WLAN LED pin to be 0 and removing redundant entry. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx/ath79: ag71xx: dont fetch the same var againKoen Vandeputte2019-08-271-1/+1
| | | | | | | tx_size was just declared above and set to BIT(tx->order) Use the declaration instead, which could avoid a pointer deref Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ag71xx: use base address value directly from the sourceKoen Vandeputte2019-08-271-2/+2
| | | | | | This brings the code more inline with the ath79 flavour Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: ag71xx: make use of managed dev API simplifying codeKoen Vandeputte2019-08-271-51/+34
| | | | | | | | | Backport of a4eef43a120d ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev") combined with the initial changes from John Crispin. Simplifies the code a lot by using the Managed dev API. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-30 01:34:18 +0000