aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/patches-4.9
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: kernel: enable PCI on QCA9556 SoCRoger Pueyo Centelles2018-01-151-0/+12
| | | | | | | | | This patch enables the PCI bus on the QCA9556 SoC, the same way it is done on the same family SoC QCA9558. Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: disable devicetree supportMatthias Schiffer2018-01-133-4/+74
| | | | | | | | | | | | While we'd like to convert ar71xx to DT-based configuration eventually, we aren't quite there yet, and shipping half-baked DT support that is not used at all wastes precious space. Saves ~120KB before LZMA, ~33KB after LZMA. Run-tested on TP-Link CPE510 and TL-WR841 v7. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: bump 4.9 to 4.9.75Kevin Darbyshire-Bryant2018-01-101-2/+2
| | | | | | | | | | | | | Refresh patches Fixes: CVE-2017-5754 aka Meltdown Tested-on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [fix conflict after 4.14 bump] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: fix Kconfig dependency of the 88E6063 switch DSA driverGabor Juhos2018-01-091-1/+2
| | | | | | | | | | | | The Marvell 88E6063 ethernet switch driver depends on the DSA framework. Add a 'depends on NET_DSA' statement to its Kconfig entry to state that explicitly. Fixes the following Kconfig warning: warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA) Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* kernel: Update kernel 4.9 to 4.9.70Hauke Mehrtens2017-12-193-3/+3
| | | | | | Runtime tested on lantiq. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: fix board detection with newer RouterBOOT versionsGabor Juhos2017-12-121-0/+43
| | | | | | | | | | | | | | | Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD) use "Board=" kernel parameter instead of "board=" to pass the board name to the kernel. Due to this change the board detection code is not working on the devices shipped with the new RouterBOOT version. Because the kernel is unable to identify these boards they become unusable despite that they are supported by the current code. Update the prom_init code to convert the 'Board' kernel parameter to 'board'. After this change, the board detection works also with the new RouterBOOT versions. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* kernel: MIPS compile out no-op DMA mapping ops where possibleFelix Fietkau2017-12-081-1/+1
| | | | | | Slightly improves networking throughput on some devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.9 to 4.9.67Stijn Tintel2017-12-073-3/+3
| | | | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - generic/190-1-5-e1000e-Fix-error-path-in-link-detection.patch - generic/190-3-5-e1000e-Fix-return-value-test.patch - generic/190-4-5-e1000e-Separate-signaling-for-link-check-link-up.patch - generic/190-5-5-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - ramips/0102-MIPS-ralink-Fix-MT7628-pinmux.patch - ramips/0103-MIPS-ralink-Fix-typo-in-mt7628-pinmux-function Update patches that no longer apply: - layerscape/815-spi-support-layerscape.patch - ramips/0099-pci-mt7620.patch Compile-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64. Runtime-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.9 to 4.9.63Koen Vandeputte2017-11-222-2/+2
| | | | | | | | | | | Refreshed all patches. Removed upstreamed parts. Compile-tested: cns3xxx, imx6, mvebu, layerscape Run-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: complete support for RB mAP 2nDRobert Marko2017-11-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD mAP 2nD https://mikrotik.com/product/RBmAP2nD Specifications: - SoC: Qualcomm QCA9531 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: builtin QCA9531, 2x2:2 - Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2) - USB: microUSB type AB port This patch adds missing code to fully support mAP. Machfile already contained configuration for mAP 2nD, but device specific configuration like LEDs etc., was missing. Note: The POE LED works but doesn't turn on when POE passthrough is enabled, despite being configured with GPIO trigger. Installation 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ar71xx: complete support for RB wAP 2nDRobert Marko2017-11-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD wAP https://mikrotik.com/product/RBwAP2nD Specifications: - SoC: Qualcomm QCA9533 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9533, 2x2:2 - Ethernet: 1x100M (802.3af/at POE in) This patch adds missing code to fully support wAP. Machfile already contained configuration for wAP 2nD but device specific configuration like LEDs etc. was missing. Installation: 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ar71xx: fix regression in 74x164 initialization with 4.9Felix Fietkau2017-11-101-10/+12
| | | | | | | | | The memcpy of the init data relies on chip->registers to be initialized, which only happens later in the code. Move this initialization further down to make it work. This was breaking PCIe/USB on some MikroTik RouterBoard devices. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix flash fast read on devices using multiple flash chipsFelix Fietkau2017-11-051-5/+11
| | | | | | | Add a callback to allow the SPI driver to indicate which devices fast flash read works on. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: Add kernel 4.9 supportHauke Mehrtens2017-10-1187-0/+7197
This add support for kernel 4.9 to the ar71xx target. It was compile tested with the generic, NAND and mikrotik subtarget. Multiple members of the community tested it on their boards and did not report any major problem so far. Especially the NAND part received some changes to adapt to the new kernel APIs. The serial driver hack used for the Arduino Yun was not ported because the kernel changed there a lot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 07:51:40 +0000