aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/patches-4.4
Commit message (Collapse)AuthorAgeFilesLines
* kernel: Update kernel 4.4 to 4.4.100Rosen Penev2017-11-251-3/+3
| | | | | | Run-tested on ramips Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ar71xx: complete support for RB mAP 2nDRobert Marko2017-11-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD mAP 2nD https://mikrotik.com/product/RBmAP2nD Specifications: - SoC: Qualcomm QCA9531 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: builtin QCA9531, 2x2:2 - Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2) - USB: microUSB type AB port This patch adds missing code to fully support mAP. Machfile already contained configuration for mAP 2nD, but device specific configuration like LEDs etc., was missing. Note: The POE LED works but doesn't turn on when POE passthrough is enabled, despite being configured with GPIO trigger. Installation 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ar71xx: complete support for RB wAP 2nDRobert Marko2017-11-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD wAP https://mikrotik.com/product/RBwAP2nD Specifications: - SoC: Qualcomm QCA9533 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9533, 2x2:2 - Ethernet: 1x100M (802.3af/at POE in) This patch adds missing code to fully support wAP. Machfile already contained configuration for wAP 2nD but device specific configuration like LEDs etc. was missing. Installation: 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: bump 4.4 to 4.4.91Kevin Darbyshire-Bryant2017-10-081-1/+1
| | | | | | | | | Refresh patches. Compile-tested for: ar71xx Archer C7 v2 Run-tested on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ar71xx: Fix NULL pointer dereferece in at803x_link_change_notify()Andrey Jr. Melnikov2017-10-071-2/+2
| | | | | | | Check pdata pointer before use to avoid OOPS if dev_get_platdata() return NULL. Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
* ar71xx: rework chipidea usb controller patchFelix Fietkau2017-10-071-13/+44
| | | | | | | | Handle AR9344 as well. Disable the EHCI platform device when device mode is active, to avoid resource conflicts. Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* kernel: update 4.4 to 4.4.85Kevin Darbyshire-Bryant2017-08-311-1/+1
| | | | | | | | Refresh patches Compile & run tested: ar71xx - Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* kernel: update kernel 4.4 to version 4.4.79Hauke Mehrtens2017-07-281-37/+0
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update kernel 4.4 to 4.4.74Stijn Tintel2017-06-2712-22/+22
| | | | | | | | Refresh patches. Compile-tested on ar71xx. Runtime-tested on ar71xx. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: add AR724x PCIe init fixesMathias Kresin2017-06-248-33/+175
| | | | | | | | | | | | Add upstream send AR724x PCIe patches to get the PCIe controller out of reset during driver init. The AVM Fritz 300E bootloader doesn't take care of releasing the different PCIe controller related resets which causes an endless hang as soon as either the PCIE Reset register (0x180f0018) or the PCI Application Control register (0x180f0000) is read from. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: fixup ar71xx/ar933x_wmac_reset: remove indefinite wait for wmac resetKevin Darbyshire-Bryant2017-06-111-1/+1
| | | | | | Fix malformed patch introduced by 296312fca13a4cab1d157e0474e1f0bcca6adf5c Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* ar71xx/ar93xx_wmac_otp_read_word: fix wrongly used sizeof(*u)Alexander Couzens2017-06-111-2/+2
| | | | | Found-by: Coverity Scan #1330474 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ar71xx/ar933x_wmac_reset: remove indefinite wait for wmac resetAlexander Couzens2017-06-111-2/+1
| | | | | Found-by: Coverity Scan #1329327 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* kernel: update kernel 4.4 to 4.4.71Jo-Philipp Wich2017-06-071-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes the following security vulnerabilities: CVE-2017-8890 The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the Linux kernel through 4.10.15 allows attackers to cause a denial of service (double free) or possibly have unspecified other impact by leveraging use of the accept system call. CVE-2017-9074 The IPv6 fragmentation implementation in the Linux kernel through 4.11.1 does not consider that the nexthdr field may be associated with an invalid option, which allows local users to cause a denial of service (out-of-bounds read and BUG) or possibly have unspecified other impact via crafted socket and send system calls. CVE-2017-9075 The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel through 4.11.1 mishandles inheritance, which allows local users to cause a denial of service or possibly have unspecified other impact via crafted system calls, a related issue to CVE-2017-8890. CVE-2017-9076 The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux kernel through 4.11.1 mishandles inheritance, which allows local users to cause a denial of service or possibly have unspecified other impact via crafted system calls, a related issue to CVE-2017-8890. CVE-2017-9077 The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel through 4.11.1 mishandles inheritance, which allows local users to cause a denial of service or possibly have unspecified other impact via crafted system calls, a related issue to CVE-2017-8890. CVE-2017-9242 The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel through 4.11.3 is too late in checking whether an overwrite of an skb data structure may occur, which allows local users to cause a denial of service (system crash) via crafted system calls. Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890 Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074 Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075 Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076 Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077 Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242 Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.71 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: update kernel 4.4 to version 4.4.69Kevin Darbyshire-Bryant2017-05-215-20/+20
| | | | | | | | | | | | | | | | | | | Refresh patches. A number of patches have landed upstream & hence are no longer required locally: 062-[1-6]-MIPS-* series 042-0004-mtd-bcm47xxpart-fix-parsing-first-block Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup as it was incorrectly included upstream thus dropped from LEDE. As it has now been reverted upstream it needs to be included again for LEDE. Run tested ar71xx Archer C7 v2 and lantiq. Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk> [update from 4.4.68 to 4.4.69] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "ar71xx: Add support for Teltonika RUT900"John Crispin2017-05-181-25/+0
| | | | | | | | This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: Add support for Teltonika RUT900Steffen Weinreich2017-05-181-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org>
* ar71xx: fold 641-MIPS-ath79-fix-AR934x-OTP-offsets.patch into the patch that ↵Felix Fietkau2017-04-2615-131/+91
| | | | | | it fixes Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: Add OTP support for AR934xChris Blake2017-04-261-0/+66
| | | | | | | | | | The patch 523-MIPS-ath79-OTP-support only supports the OTP offsets for AR933x chips, which has changed on newer platforms such as the AR934x. The follwoing change is to add support for reading the OTP on the AR934x. Tested on an Aerohive AP-121. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* kernel: update kernel 4.4 to 4.4.56Hauke Mehrtens2017-03-261-1/+1
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: add support for MikroTik hAP acRyan Mounce2017-03-231-1/+2
| | | | | | | | | | | This patch adds initial support for the MikroTik RouterBOARD hAP ac (RB962UiGS-5HacT2HnT). All functions are supported except: -SFP cage (eth1) is not working -WLAN LEDs are not working Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ar71xx: add support for RB LHG 5nDThibaut VARENE2017-03-151-1/+2
| | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD LHG 5 https://routerboard.com/RBLHG-5nD Specifications: - SoC: Atheros AR9344 (600MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin AR9344 5GHz, 2x2:2 - Ethernet: 1x100M Initial flash via initramfs, like all other RB devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* kernel: update kernel 4.4 to 4.4.53Hauke Mehrtens2017-03-121-1/+1
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: fix build without CONFIG_NOP_USB_XCEIV (FS#593)Felix Fietkau2017-03-071-9/+6
| | | | | | | | Open-code usb_phy_generic_register instead of calling it, since it is really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel config and add a proper dependency instead Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: Enable RB2011 TTYArvid E. Picciani2017-02-261-1/+2
| | | | | | Enables TTY on the Mikrotik RouterBoard RB2011*R* Signed-off-by: Arvid E. Picciani <aep@exys.org>
* kernel: update kernel 4.4 to 4.4.50Kevin Darbyshire-Bryant2017-02-231-11/+11
| | | | | | | | | | Bump kernel from 4.4.49 to 4.4.50 Compile tested: All targets Run tested: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* ar71xx: Add more boards to the routerboard serial detection patchThibaut VARENE2017-02-201-1/+3
| | | | | | This patch enables serial console on the 435 series and the 953gs. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add new SPI NOR RB devices to the list of serial-enable patchThibaut VARENE2017-02-151-1/+5
| | | | Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* kernel: bump to 4.4.45Koen Vandeputte2017-01-271-2/+2
| | | | | | | | Refreshed patches for all supported targets. Compiled & tested on cns3xxx & imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Kernel: bump to 4.4.44Stijn Segers2017-01-273-37/+25
| | | | | | | | Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64. .44 has been run-tested on the 17.01 branch here on ar71xx and mt7621. Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx: QCA956X: add missing registerHenryk Heisig2017-01-263-3/+41
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: Chipidea USB device supportSvetoslav Neykov2017-01-202-0/+179
| | | | | | | | | | | | Changes the platform to use the Chipidea driver instead of the generic USB host driver which has support for both host and device modes (selected on boot). The changes in 930-chipidea-pullup.patch are already in mainline. I'll upstream 920-usb-chipidea-AR933x-platform-support.patch once I can test the changes with a newer kernel. Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
* kernel: backport MIPS changes introducing a separate IRQ stackFelix Fietkau2017-01-151-1/+1
| | | | | | | | Prevents crashes when IRQs arrive when the current kernel stack context already contains deeply nested function calls, e.g. when stacking lots of network devices on top of each other Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: enable serial console on Mikrotik RB411/RB433David Varga2017-01-131-1/+3
| | | | | | | | | This patch adds support for serial console on Mikrotik RB411 and RB433 series devices. Signed-off-by: David Varga <duvi@duvinet.hu> [picked from FS#377] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: remove a non-upstream spi core patchFelix Fietkau2017-01-051-19/+0
| | | | | | | - use standard flags instead - remove dead code from the rb4xx spi drivers Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump to 4.4.39Kevin Darbyshire-Bryant2016-12-203-13/+13
| | | | | | | | Bump & refresh patches for all 4.4 targets. Compile & run tested: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* kernel: bump to 4.4.38Kevin Darbyshire-Bryant2016-12-131-1/+1
| | | | | | | | Bump & refresh patches for all 4.4 supported targets. Compile & run tested: ar71xx - Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* ar71xx: remove obsolete flash chip locking codeFelix Fietkau2016-12-125-52/+11
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP81 reference design board supportFelix Fietkau2016-12-129-104/+9
| | | | | | This board is very old and unlikely to still be relevant today. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP83 reference design board supportFelix Fietkau2016-12-123-73/+2
| | | | | | | | This board is very old and unlikely to still be relevant today. Support for it contains a significant amount of device specific baggage which is worth getting rid of. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: clean up spi controller related patchesFelix Fietkau2016-12-1216-591/+194
| | | | | | Remove various hacks for fast read, un-break device tree support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for configuring at803x PHY GPIO reset via platform dataFelix Fietkau2016-12-041-0/+68
| | | | | | | Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW, because ar71xx is not converted to device tree yet. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: enable serial console on mikrotik devicesJoão Chaínho2016-11-181-1/+4
| | | | | | | This patch enables the serial console on some Mikrotik devices (RB450, RB450G, RB493G, RB750UP). Signed-off-by: João Chaínho <joaochainho@gmail.com>
* kernel: update kernel 4.4 to version 4.4.32Stijn Tintel2016-11-161-2/+2
| | | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on all targets that use kernel 4.4 and aren't marked broken. Runtime-tested on ar71xx, octeon. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: update to v4.4.23Álvaro Fernández Rojas2016-09-301-1/+1
| | | | | | | Refresh patches for all targets that support kernel 4.4. compile/run-tested on brcm2708/bcm2710 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker GatewayChris Blake2016-09-271-1/+1
| | | | | | | | | This patch adds support for Cisco's Z1. Detailed instructions for the flashing the device can be found in the OpenWrt wiki: <https://wiki.openwrt.org/toh/meraki/z1> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* kernel: update kernel 4.4 to version 4.4.20Álvaro Fernández Rojas2016-09-153-3/+3
| | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on brcm2708 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: Backport pending appended DTB handling patchesDaniel Gimpelevich2016-09-121-1/+1
| | | | | | | | | | Backport patches from upstream Linux kernel which are making the kernel stores the appended dtb not in the same resisters as defined in the UHI specification, use a separate variable on MIPS. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [some modifications] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update kernel 4.4 to version 4.4.19Stijn Tintel2016-08-231-4/+4
| | | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on all targets that use kernel 4.4 and aren't marked broken. Runtime-tested on ar71xx, octeon and x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: add missing LZO support select for routerboard devicesFelix Fietkau2016-08-041-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-08 08:04:45 +0000