aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/mikrotik
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: reorganize kernel configurationMatthias Schiffer2018-01-131-211/+21
| | | | | | | | | | Rather than including all machines for the generic subtarget in the base configuration, leave the base configuration without specific machines and create a proper subtarget config for ar71xx/generic. The configuration diffs of the mikrotik and nand subtargets get significantly shorter, as will the configurations of future subtargets. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: disable devicetree supportMatthias Schiffer2018-01-131-1/+0
| | | | | | | | | | | | While we'd like to convert ar71xx to DT-based configuration eventually, we aren't quite there yet, and shipping half-baked DT support that is not used at all wastes precious space. Saves ~120KB before LZMA, ~33KB after LZMA. Run-tested on TP-Link CPE510 and TL-WR841 v7. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx/mikrotik: disable TP-Link TL-WR810N v2 board supportGabor Juhos2018-01-091-0/+1
| | | | | | It does not belongs to the MikroTik boards. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx/mikrotik: disable unused MTD partitioning and split driversGabor Juhos2018-01-091-0/+6
| | | | | | Reduces the compressed kernel size by ~2.5KB. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx/mikrotik: disable unused ethernet switch and phy driversGabor Juhos2018-01-091-0/+4
| | | | | | | | | | | | | | | | | | | | Disable the drivers for the following ethernet switches: Realtek RTL8306 Realtek RTL8366/8367 Marvell 88E6060 (DSA) Marvell 88E6063 (DSA) Also disable the phy driver for Marvell PHYs. None of the supported RouterBOARDs are using any device which needs these drivers. Disable the DSA framework too, because it is not required by the remaining switch drivers. This reduces the compressed kernel size by ~20KB. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: sort kernel configurationsGabor Juhos2018-01-091-1/+1
| | | | | | | The symbols in some kernel configurations of the target are in wrong order. Sort them with kconfig.pl. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: add support for TP-Link TL-WR1043N v5Tim Thorpe2017-11-141-0/+1
| | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4, except that the USB port has been removed and there is no longer a removable antenna option. The software is more in line with the Archer series in that it uses a nested bootloader scheme. Specifications: - QCA9563 at 775 MHz - 64 MB RAM - 16 MB flash - 3 (non-detachable) Antennas / 450 Mbit - 1x/4x WAN/LAN Gbps Ethernet (QCA8337) - reset and Wi-Fi buttons Signed-off-by: Tim Thorpe <tim@tfthorpe.net> Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: add support for Wallys DR342Piotr Dymacz2017-11-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342. Short specification: - 560/450/225 MHz (CPU/DDR/AHB) - 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V) - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm - 2x MMCX connectors - miniPCIe connector with PCIe and USB 2.0 buses - optional miniSIM slot - 7x LED, 1x button - UART, (E)JTAG and LED headers - 1x DC jack for main power (12-56 V) Flash instruction (do it under U-Boot, using UART): 1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: only use SPI NOR 4K sectors on smaller flash chips for mikrotik devicesFelix Fietkau2017-11-061-1/+0
| | | | | | | | On NOR based Mikrotik devices, 4K sectors significantly slow down firmware flashing and jffs2 usage. On NAND based devices they may be necessary to run rbcfg (the boot loader config is often on SPI NOR). Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add support for limiting 4K erase sector support based on flash chip ↵Felix Fietkau2017-11-061-0/+1
| | | | | | | | | | | | | | | | size Some targets need 4K sectors for small flash chips (e.g. some routerboards, where the entire chip is just one "erase block"), whereas on other devices 4K sectors lead to horrible flash erase/write performance. Set the default limit in the generic kernel configuration to 4 MiB to ensure that all new platforms don't use 4K sectors for bigger flash chips. On all existing targets use 16 MiB for now to avoid regressions. They will be changed individually in follow-up commits. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: re-enable 4k sectors for the mikrotik subtargetsFelix Fietkau2017-10-241-0/+1
| | | | | | | | On RB91x (and possibly others), there is a small SPI flash to store boot loader and configuration. It needs 4K sectors to be able to write the configuration using rbcfg Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: Add kernel 4.9 supportHauke Mehrtens2017-10-111-1/+1
| | | | | | | | | | | | | This add support for kernel 4.9 to the ar71xx target. It was compile tested with the generic, NAND and mikrotik subtarget. Multiple members of the community tested it on their boards and did not report any major problem so far. Especially the NAND part received some changes to adapt to the new kernel APIs. The serial driver hack used for the Arduino Yun was not ported because the kernel changed there a lot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: unify CONFIG_CMDLINEFelix Fietkau2017-09-281-1/+0
| | | | | | | Booting from jffs2 directly is no longer supported, use rootfstype=squashfs consistently for all subtargets Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for COMFAST CF-E355ACEnrique Giraldo2017-09-101-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9882. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 64MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net> [whitespace fixes, ac radio caldata offset fix] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-USB150Piotr Dymacz2017-09-101-0/+1
| | | | | | | | | | | | | | | | | | | | | GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4) - 1T1R 2.4 GHz - 2x LED, 1x button - UART header on PCB Flash instruction: Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used to flash LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP121FPiotr Dymacz2017-07-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users. Device is based on Atheros AR9331 WiSoC and is running a custom version (updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR1) - 16 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet - 1T1R 2.4 GHz - 1x microSD (optional, on separate PCB) - 3x LED, 1x button, 1x switch - UART header on PCB Flash instruction (under U-Boot web recovery mode): 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR902AC v1Piotr Dymacz2017-07-041-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FWPiotr Dymacz2017-07-041-0/+1
| | | | | | | | We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel with TP-Link header embedded inside "safeloader" image type and thus get rid of statically defined "kernel" and "rootfs" partitions in cmdline. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: refresh and cleanup mikrotik subtarget kernel configPiotr Dymacz2017-07-041-8/+2
| | | | | | | Refresh mikrotik subtarget kernel config and enable kernel support for boards which belong to this subtarget only. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link Archer C58 v1Henryk Heisig2017-06-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 3x button - UART header on PCB, RX, TX at TP4+5 (backside) QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to patch macaddress. Flash instruction: Use "factory" image directly in vendor GUI. Recovery method: 1. Set PC to fixed ip address 192.168.0.66/24. 2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and rename it to "tp_recovery.bin". 3. Start a tftp server with the file "tp_recovery.bin" in its root directory. 4. Turn off the router. 5. Press and hold Reset button. 6. Turn on router with the reset button pressed and wait ~15 seconds. 7. Release the reset button and after a short time the firmware should be transferred from the tftp server. 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f020000 +$filesize cp.b $fileaddr 0x9f020000 $filesize reset This commit is based on GitHub PR#1112 Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ar71xx: add support for TP-Link TL-WA855RE v1Federico Cappon2017-06-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/397/198 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x external antennas - 2x LED (green and orange in the same package), 2x button - UART: TP5(TX) and TP4(RX) test points on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in EU version of the device, but should work also with the same device version sold in other countries. Signed-off-by: Federico Cappon <dududede371@gmail.com>
* ar71xx: add AVM FRITZ!WLAN Repeater 300E supportMathias Kresin2017-06-241-0/+3
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: AR7242 (Virian 400MHz) * RAM: 64 MB DDR (W9751G6JB-25) * Flash: 16MB SPI flash (S25FL129PIF) * WiFi: AR9382 (2.4/5GHz) + 2x SE2595L * LAN: 1x1000M (PEF7071V) To install LEDE via EVA bootloader, a FTP connection need to be established to 192.168.178.1 within the first seconds after power on: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: add support for TP-Link Archer C25 v1Ludwig Thomeczek2017-06-111-0/+1
| | | | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net> [minor code style fixes, boards alphabetical order fixes, reworked commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-Link TL-WR942N v1Serg Studzinskii2017-06-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: disable ENS202EXT in mikrotik and nand subtargetsJo-Philipp Wich2017-05-311-0/+1
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: Add support for TP-Link MR6400Filip Moc2017-05-271-0/+1
| | | | | | | | | | | | | | | | | You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Hardware Specification (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Signed-off-by: Filip Moc <lede@moc6.cz>
* ar71xx: enable nand-utils in the mikrotik subtarget to ensure it makes it to ↵Felix Fietkau2017-05-121-0/+2
| | | | | | | | initramfs Without it, sysupgrade from initramfs to nand fails Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: Compex WPJ563 supportChristian Mehlis2017-03-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc) - RAM: 128 MiB - Storage: 16MB NOR flash - Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO - Ethernet: 2x1G Tested and working: - ethernet / switch / lan / wan - 2.4GHz SoC wifi - PCIe - leds - buzzer Ramload: - tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin - bootm 0x84000000 Install: - tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin - erase 0x9f030000 +$filesize - erase 0x9f680000 +1 - cp.b $fileaddr 0x9f030000 $filesize Erasing 0x9f680000 is required because uboot defines "bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot the higher address. I think the 16 mb flash are intended to be used as 8+8mb for a fallback image. In my hardware only the lower address has a bootable image. But to make sure future hardware will boot lede too, I erase one block, so uboot will skip this address. Signed-off-by: Christian Mehlis <christian@m3hlis.de>
* ar71xx: add support for P&W R602N and CPE505NPiotr Dymacz2017-03-231-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for TP-LINK TL-WR840N v2 and v3Vaclav Svoboda2017-03-231-0/+1
| | | | | | | | | | | | | | This patch adds support for the TP-LINK TL-WR840N v2 and v3. - SoC: Qualcomm QCA9533-BL3A (650 MHz) - RAM: 32 MiB (Zentel A3S56D40GTP) - Flash: 4 MiB (v2: Macronix MX 25L323F) (v3: Winbond 25Q32FVSIG) - LAN: 4x 100M - WAN: 1x 100M Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
* ar71xx: add support for Rockeetech AP531B0Shuanglin Liu2017-03-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB)) - RAM: 64 MiB DDR2 - Storage: 16 MiB of flash (optional 16 MiB second flash) - Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) 1x100M (port 4) - PCI-E: x1 - SIMcard slot: x1 - USB 2.0 port: x1 (optional) - Ext GPIO pin: x8 - UART for serial console: x1 - External watchdog: x1 (optional) - Power supply: 9-48V (DC jack/passive PoE) Installation through tftp: - Copy <Firmware Image Name> into tftp directory - Connect board via ttl port and Ethernet port - Boot the AP531B0 - When "Autobooting in 1 seconds" appears press Enter - Set serverip and ipaddr appropriate (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1) - Enter "tftp 0x8050000 <Firmware Image Name>" - Enter "erase 0x9f050000 +$filesize" - Enter "cp.b 0x80500000 0x9f050000 $filesize" - Enter "reset" Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
* ar71xx: add support for TL-WR802N Version 2Thomas Roberts2017-02-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the TP-Link TL-WR802N Version 2. Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of FLash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to http://192.168.0.1 (default user is "admin" & password is "admin) - Go to "System Tools -> Firmware Upgrade" - Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 <Firmware Image Name> - Record the result of "printenv bootcmd" - Enter "erase <Result of 'printenv bootcmd'> +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm <Result of 'printenv bootcmd'>" (e.g bootm 0x9f020000) Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
* ar71xx: add support for 8devices Lima boardKarol Dudek2017-02-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lima is a module for the (IoE) internet of everything applications, based on Qualcomm/Atheros QCA4531. Specification: - 650/600/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 32 MB of FLASH - 2T2R 2.4 GHz - 2x 10/100 Mbps Ethernet - USB 2.0 Host - PCIe - UART for serial console - 14x GPIO Flash instruction: 1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin and rename it to 8dev_recovery.bin 2. Binary file copy to USB stick and plug into slot USB 3. Press S2 (reset) button 4. Press and hold the S1 button by 5 seconds 5. Wait ~40 seconds to complete recovery Tested on: - Lima development kit Signed-off-by: Karol Dudek <karoiz@sli.pl>
* ar71xx: provide support for RB-941-2nD via mach-rbspi.cThibaut VARENE2017-02-151-1/+0
| | | | | | | | | This patch implements support for the hAP lite in mach-rbspi.c hAP lite was supported via mach-rb941.c, so this file is removed as well as the corresponding build bits. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for RB mAP L-2nDThibaut VARENE2017-02-151-0/+1
| | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD mAP lite https://routerboard.com/RBmAPL-2nD Specifications: - SoC: Qualcomm QCA9533 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Wireless: builtin QCA9533, 2x2:2 - Ethernet: 1x100M This is another 16M SPI NOR mikrotik device. The machine file is named mach-rbspi.c because I plan to add support for several of the other spi-based RouterBOARD devices in subsequent patches: they share most of the hardware and thus the same codebase. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ar71xx: add support for TP-Link TL-WA850RE v2Piotr Dymacz2017-02-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Image was tested only in US version of the device, but should work also with the same device version sold in other countries. Available FLASH space, with LEDE trunk, is only 240 KB. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix up mikrotik subtarget kernel configPiotr Dymacz2017-02-031-0/+4
| | | | | | Disable all devices which do not belong to the mikrotik subtarget. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support to TP-Link Archer C59v1 and C60v1Henryk Heisig2017-01-261-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: Fix mikrotik subtarget default profile for device profile selectionAlex Samorukov2017-01-251-0/+1
| | | | Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
* ar71xx: improve Mikrotik hAP Lite device supportAlex Samorukov2017-01-251-2/+0
| | | | | | | | - remove CONFIG_MTD_SPI_NOR_USE_4K_SECTORS - enable jffs2 support - fix sysupgrade Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
* ar71xx: fix up the kernel config for the mikrotik subtargetFelix Fietkau2017-01-161-0/+64
| | | | | | Limit enabled devices to routerboards, disable all other devices Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: convert mikrotik routerboard support to UBIFelix Fietkau2017-01-162-22/+18
| | | | | | | | | | Remove the wget2nand script, drop the need for manual installation, use sysupgrade instead. There are now two different NAND images, one for 64 MiB flashes, the other for >= 128 MiB Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: create a proper default profile for the mikrotik subtarget, drop ↵Felix Fietkau2017-01-162-23/+6
| | | | | | other profiles Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for TP-Link RE450Tal Keren2016-12-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | Add full support for TP-Link RE450. The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci). The ethernet interface is AR8035, but the mdio is connected to the gpio and the chipset builtin mdio bus isn't used, which is unique (and weird), so the kernel gpio mdio module is used. The two ethernet leds are connected to the GPIO, so they are both configured, one to indicate link status and the other to indicate data transfer. The generation of the image was added to the image Makefile. The return value of tplink-safeloader is not ignored anymore (to fail on error) The result factory image is flashable from the stock web ui. Signed-off-by: Tal Keren <kooolk@gmail.com> [rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand] Signed-off-by: Radek Dostál <rd@radekdostal.com> [hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard] Signed-off-by: Henryk Heisig <hyniu@o2.pl> [jo@mein.io: squash fixes from Radek and Henryk into original commit] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for TP-LINK WR1043ND v4Ludwig Thomeczek2016-12-201-0/+1
| | | | Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: add support for TP-LINK TL-WR940N v4David Lutz2016-12-161-0/+1
| | | | Signed-off-by: David Lutz <kpanic@hirnduenger.de>
* ar71xx: remove PB92 reference design board supportFelix Fietkau2016-12-121-1/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP113 reference design board supportFelix Fietkau2016-12-121-1/+0
| | | | | | | Due to flash size limitations, support for this board has not been functional for years Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP81 reference design board supportFelix Fietkau2016-12-121-1/+0
| | | | | | This board is very old and unlikely to still be relevant today. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove AP83 reference design board supportFelix Fietkau2016-12-121-1/+0
| | | | | | | | This board is very old and unlikely to still be relevant today. Support for it contains a significant amount of device specific baggage which is worth getting rid of. Signed-off-by: Felix Fietkau <nbd@nbd.name>